Chauvet SlimPAR HEX 6 IRC User manual

User Manual

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 2 of 24
TABLE OF CONTENTS
1. Before You Begin..................................................................................................................................................... 4
What Is Included.................................................................................................................................................................................4
Unpacking Instructions.......................................................................................................................................................................4
Claims............................................................................................................................................................................................4
Manual Conventions...........................................................................................................................................................................4
Symbols...............................................................................................................................................................................................4
Disclaimer............................................................................................................................................................................................4
Product at a Glance............................................................................................................................................................................5
Safety Notes........................................................................................................................................................................................5
2. Introduction............................................................................................................................................................... 6
Overview..............................................................................................................................................................................................6
Dimensions..........................................................................................................................................................................................7
3. Setup.......................................................................................................................................................................... 8
AC Power ............................................................................................................................................................................................8
Fuse Replacement........................................................................................................................................................................8
Fuse Replacement Diagram...................................................................................................................................................8
Power Linking................................................................................................................................................................................9
Power Linking Diagram...........................................................................................................................................................9
Mounting............................................................................................................................................................................................10
Orientation ...................................................................................................................................................................................10
Rigging.........................................................................................................................................................................................10
Rigging Diagram....................................................................................................................................................................10
DMX Linking......................................................................................................................................................................................11
DMX Linking Diagram.................................................................................................................................................................11
4. Operation................................................................................................................................................................. 12
Control Panel Description.................................................................................................................................................................12
Menu Map....................................................................................................................................................................................12
DMX Configuration ...........................................................................................................................................................................13
DMX Starting Address................................................................................................................................................................13
DMX Personalities.......................................................................................................................................................................13
DMX Channel Assignments and Values...................................................................................................................................14
12-CH.....................................................................................................................................................................................14
8-CH.......................................................................................................................................................................................14
6-CH.......................................................................................................................................................................................14
Standalone Configuration.................................................................................................................................................................15
Static Color Mode........................................................................................................................................................................15
Auto Program Mode....................................................................................................................................................................15
Program Speed...........................................................................................................................................................................15
Sound-Active Mode.....................................................................................................................................................................16
Custom Color Mode....................................................................................................................................................................16
Infrared (IR) Remote Control......................................................................................................................................................17
IRC-6 Operation ....................................................................................................................................................................17
Master/Slave Configuration..............................................................................................................................................................19
Configuring the Slaves................................................................................................................................................................19
Configuring the Master ...............................................................................................................................................................19
Settings Configuration......................................................................................................................................................................20
Program Speed...........................................................................................................................................................................20
Sound Sensitivity.........................................................................................................................................................................20
Dimmer Mode..............................................................................................................................................................................20

Page 3 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
5. Technical Information............................................................................................................................................ 21
Product Maintenance........................................................................................................................................................................21
6. Technical Specifications....................................................................................................................................... 22
Returns........................................................................................................................................................................ 23
Contact Us................................................................................................................................................................... 24

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 4 of 24
1.
B
EFORE
Y
OU
B
EGIN
What Is
Included
•SlimPAR™ HEX 6 IRC
•Hanging Bracket with Mounting Hardware
•
Power Cord
•Warranty Card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the SlimPAR™ HEX 6 IRC and check that all the parts are in the package, and are
in good condition.
Claims
If the box, or any of the contents, appear damaged from shipping, save all the packaging and file a
claim with the carrier immediately. Failure to report damage to the carrier immediately, or failure to
save all the packaging, can invalidate a claim.
For other issues, such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with Chauvet within 7 days of delivery. See Contact Us at the end of
this manual.
Manual
Conventions
Convention
Meaning
1—512
A range of values
50/60
A set of values
Settings
A menu option
Menu > Settings
A sequence of menu options
<Enter>
A button
Symbols
Convention
Meaning
Critical information. Ignoring it can cause malfunction, damage the product, or harm
the operator.
Important information. Ignoring it can cause the product to malfunction.
Useful information.
Disclaimer
The information and specifications contained in this User Manual are subject to change without
notice. Chauvet assumes no responsibility or liability for any errors or omissions, and reserves the
right to revise or recreate this manual at any time. The latest version of this manual can
be
downloaded from http://www.chauvetlighting.com/product-manuals-literature/.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Date
M. Trouard
1/30/2015
A. Leon
2/11/2015

Page 5 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Product at a
Glance
Use on Dimmer
x
Auto Program
P
Outdoor Use
x
Auto-Ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important information about the mounting, use, and maintenance of this
product. Read these notes before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Make sure the power cord is not crimped or damaged.
•Always disconnect the product from the power source before cleaning it or replacing the fuse.
•Never disconnect the product from the power source by pulling or tugging on the cord.
•If mounting the product overhead, always secure it with a safety cable.
•Make sure there are no flammable materials close to the product when it is operating.
•Avoid direct eye exposure to the light source while the product is on.
•Do not touch the product’s housing when the product is operating.
•This product is not intended for permanent installation.
•The product is for indoor use only.
•Do not expose the product to rain or moisture.
•Make sure that the voltage of the power source used for the product is within the range stated on
the label, on the rear panel of the product, or Technical Specifications in this manual.
•Never connect the product to a dimmer or a rheostat.
•Make sure to replace the fuse with another fuse of the same type and rating.
•Always install the product in a location with adequate ventilation, and leave at least 20 in (50 cm)
between the product and adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Do not operate the product in an ambient temperature higher than 104 °F (40 °C).
•Always carry the product by the mounting bracket.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by untrained people can lead to damage or
malfunction.
•If repairs are required, contact the nearest authorized technical assistance center.
See Contact Us at the end of this manual.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely
disconnect the product from power via the breaker or by unplugging it.
Keep this User Manual for future reference. If you sell the product to another user, be sure to give
this manual to the next owner.

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 6 of 24
2.
I
NTRODUCTION
Overview
Back View
Power In
Microphone
Fuse Holder
Display
Power Out
DMX In
Control
Buttons
DMX Out
Safety Loop
IR Sensor
Front View

Page 7 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Dimensions
8.9 in
226 mm
9.5 in
241 mm
3.7 in
95 mm

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 8 of 24
3.
S
ETUP
AC Power
The SlimPAR™ HEX 6 IRC has an auto-ranging power supply that works with an input voltage
range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the
current value listed on the label affixed to the product’s back panel, or refer to the
Technical Specifications in this manual. The listed current rating indicates the product’s average
current draw under normal conditions.
For more information, you may download Sizing Circuit Breakers from the Chauvet website
:
www.chauvetlighting.com/download/.
Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the
product has an appropriate electrical ground to avoid the risk of electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel is configured as a 0 to 100% switch.
Fuse
Replacement
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
Disconnect the product from power before replacing the fuse.
Fuse Replacement
Diagram
Always replace a blown fuse with another of the same type and rating.
A spare fuse is not included; however, the safety cap has room for a spare.
Installed Fuse
(held by plastic clip)
Spare Fuse Holder
(inside safety cap)
Safety cap

Page 9 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Power Linking
Daisy chaining products together through their Power In and Power Out sockets, called power
linking, allows many products to be powered from one power connection.
Up to 11 SlimPAR™ HEX 6 IRC products can be power linked at 120 V, and up to
21 SlimPAR™ HEX 6 IRC products can be power linked at 230 V.
The diagram below illustrates the power-linking process.
Power Linking
Diagram
•Do not power link more than 11 SlimPAR™ HEX 6 IRC products at 120 V.
•Do not power link more than 21 SlimPAR™ HEX 6 IRC products at 230 V.
•The power linking diagram shown above corresponds to the North American version of
the product ONLY! If using the product in other markets, you must consult with the local
CHAUVET® distributor as power linking connectors and requirements may differ in your
country or region.
1st Product
2nd Product
3rd Product
Additional Products

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 10 of 24
Mounting
Before mounting the product, read and follow the safety recommendations indicated in
the Safety Notes above. For the CHAUVET® line of mounting
clamps, go to
www.chauvetlighting.com/cables-clamps-main.html/.
Orientation
The SlimPAR™ HEX 6 IRC is designed to hang from a pipe or truss with the front lens at any angle.
Place the product so there is at least 20” of space around it. Be sure it is accessible for programming
and control panel operation.
Rigging
Rig the product from a structure or surface that can support the product’s weight. See the
Technical Specifications in this manual for the product’s weight.
When mounting the product overhead, always use a mounting clamp and safety cable. Mount the
product securely to a rigging point, such as a pipe or truss. The mounting bracket (yoke) has a
13-mm hole. The CH-05 safety cable and the CLP-15 mounting clamp (both available from Chauvet)
are appropriate for this product.
The bracket adjustment knobs allow for directional a
djustment when aiming the product to the
desired angle. Only loosen or tighten the bracket knobs manually. Using tools could damage the
knobs.
Rigging Diagram
Mounting
Clamp
Bracket
Adjustment
Knobs (2x)
Double-Bracketed
Yoke
Safety Cable

Page 11 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
DMX Linking
When operating the SlimPAR™ HEX 6 IRC in DMX mode, DMX linking in a daisy chain allows the
DMX controller to send DMX signals to all the products.
To DMX link a number of SlimPAR™ HEX 6 IRC products into a daisy chain, connect a DMX cable
from DMX Out of the DMX controller to DMX In of the first product in the daisy chain.
Then connect another DMX cable from DMX Out of the first product in the daisy chain to DMX In of
the next product.
Continue connecting each subsequent product until all the products are part of the chain.
DMX Linking
Diagram
When DMX linking SlimPAR™ HEX 6 IRC products for Master/Slave operation
, the DMX
controller is not a part of the DMX daisy chain and the master is the first product in the chain.
See Master/Slave Configuration for details.
DMX
In
DMX
Out
DMX
In
DMX
Out
2nd Product
3rd Product
Other
Products
1st Product
DMX Controller

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 12 of 24
4.
O
PERATION
Control Panel
Description
To access the control panel functions, use the four buttons underneath the display.
Button
Function
<MENU>
Enters or exits from a menu function
<UP>
Navigates up through a list or increases a numeric value
<DOWN>
Navigates down through a list or decreases a numeric value
<ENTER>
Enters into a menu function or sets the currently shown value
Menu Map
The menu map outlines the functions available through the menu, the programming levels that can
be entered, and a description for each function.
Main Function
Programming Levels
Description
DMX Personalities and
Starting Address
6-CH
d 1–d512 Selects DMX personality and
starting address
8-CH
12CH
Static Color Mode
C--
C 1–C 63
Selects static color
Auto Program Mode
P--
P 1–P 4
Selects auto program
Program Speed
S--
S 1–S100
Selects auto program speed (slow to fast)
Sound-Active Mode Snd
Snd1
Selects Sound-Active program (6-color)
Snd2
Selects Sound-Active program (63-color)
Sound Sensitivity
SenS
u 0–u100
Sets sound sensitivity
Custom Color Mode U--
r 0–r255
Red (0–100%)
g 0–g255
Green (0–100%)
b 0–b255
Blue (0–100%)
A 0–A255
Amber (0–100%)
W 0–W255
White (0–100%)
P 0–P255
Ultraviolet (0–100%)
Dimmer dIM
OFF
Dimmer, off
dIM1
Dimmer, fast speed
dIM2
Dimmer, medium speed
dIM3
Dimmer, slow speed
Infrared SET
On
Turns infrared on or off
OFF

Page 13 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
DMX
Configuration
The SlimPAR™ HEX 6 IRC has 3 different DMX personalities, with different capabilities. In general if
the DMX personality has more channels, it allows for more control functions. The following sections
describe how to configure the SlimPAR™ HEX 6 for use with a DMX controller.
For more information about DMX, see the CHAUVET® DMX Primer, available at
http://www.chauvetlighting.com/downloads/DMX_Primer_Rev6_WO.pdf.
For information about CHAUVET® DMX controllers, see the Chauvet
website at
http://www.chauvetlighting.com/controllers-main.html.
DMX Starting
Address
When choosing a DMX starting address, consider the number of DMX channels in the DMX
personality. Choosing a starting address that is too high can restrict access to some of the product’s
channels and their functions.
The SlimPAR™ HEX 6 IRC uses 6, 8, or 12 channels of DMX, depending on the personality.
•The highest DMX starting address in 6-channel personality is 507.
•The highest DMX starting address in 8-channel personality is 505.
•The highest DMX starting address in 12-channel personality is 501.
To set the DMX starting address, do the following:
1. If the display shows dand a number from 1–512, go to step 3.
2. Press <MENU> repeatedly the display shows dand a number from 1–512.
3. Use <UP> or <DOWN> to change the DMX starting address.
4. Press <ENTER> to select the DMX starting address.
DMX
Personalities
The SlimPAR™ HEX 6 IRC has 3 DMX personalities: a 6-channel personality, an 8-channel
personality, and a 12-channel personality.
DMX personalities with more channels have more
functions and provide more control options.
To set the DMX personality, do the following:
1. Press <MENU> repeatedly until the desired personality is shown.
2. Press <ENTER> to select the personality.
•6-CH is for the 6-channel personality
•8-CH is for the 8-channel personality
•12CH is for the 12-channel personality

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 14 of 24
DMX Channel
Assignments and
Values
The following tables show which DMX channels control which functions in each of the DMX
personalities. It is important to understand these channel assignments when operating the product
with a DMX controller.
12-CH
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5
Amber
000 ó255
0–100%
6
White
000 ó255
0–100%
7
Ultraviolet
000 ó255
0–100%
8
Strobe
000 ó010
No function
011 ó255
Slow to fast
9
Color
000 ó015
No function
016 ó255
Color macros
10
Auto Programs
000 ó010
No function
011 ó050
Auto program 1
051 ó100
Auto program 2
101 ó150
Auto program 3
151 ó200
Auto program 4
201 ó225
Sound-Active mode (6-color)
226 ó255
Sound-Active mode (63-color)
11
Speed
000 ó255
Auto program speed (slow to fast)
12
Dim Mode
000 ó051
Dimmer mode manually set in Menu Options
052 ó101
Dimmer mode off
102 ó152
Dimmer mode 1 (fast speed)
153 ó203
Dimmer mode 2 (medium speed)
204 ó255
Dimmer mode 3 (slow speed)
8-CH
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0–100%
2
Red
000 ó255
0–100%
3
Green
000 ó255
0–100%
4
Blue
000 ó255
0–100%
5
Amber
000 ó255
0–100%
6
White
000 ó255
0–100%
7
Ultraviolet
000 ó255
0–100%
8 Strobe
000 ó010
No function
011 ó255
Slow to fast
6-CH
Channel
Function
Value
Percent/Setting
1
Red
000 ó255
0–100%
2
Green
000 ó255
0–100%
3
Blue
000 ó255
0–100%
4
Amber
000 ó255
0–100%
5
White
000 ó255
0–100%
6
Ultraviolet
000 ó255
0–100%

Page 15 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Standalone
Configuration
Use standalone configurations to operate the product without a DMX controller. There are a variety
of standalone modes and they are powerful tools for making exciting looks.
Never connect a product operating in a standalone mode (Sound-Active, Auto Program
, or
Infrared) to a DMX chain that includes a DMX controller. Products in a standalone mode can
transmit DMX signals that interfere with the DMX signals from the controller.
Static Color Mode
Static Color mode sets the product to one of 63 preset static colors.
To select a preset static color, do the following:
1. Press <MENU> repeatedly until C-- shows on the display.
2. Press <ENTER> and C 1–C 63 shows on the display.
3. Use <UP> or <DOWN> to select the desired preset color:
4. Press <ENTER>.
Auto Program
Mode
Auto Program mode sets the product to 1 of 4 color change programs.
To enable the Auto Program mode, do the following:
1. Press <MENU> repeatedly until P-- shows on the display.
2. Press <ENTER> and P 1–P 4 shows on the display.
3. Use <UP> or <DOWN> to select the desired auto program:
•P 1 - 6-color snap
•P 2 - 6-color fade
•P 3 - 63-color snap
•P 4 - 63-color fade
4. Press <ENTER>.
Program Speed
Program Speed sets the speed of the auto programs.
To set the auto programs’ speed, follow the instructions below:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired auto program speed
S 1–S100 (slow to fast).
3. Press <ENTER>.

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 16 of 24
Sound-Active
Mode
Sound-Active mode sets the product to respond to sounds and music.
To enable the Sound-Active mode, do the following:
1. Press <MENU> repeatedly until Snd shows on the display.
2. Press <ENTER> and Snd1 (6-color) or Snd2 (63-color) shows on the display.
3. Use <UP> or <DOWN> to select the desired sound-active program.
4. Press <ENTER>.
The product will respond only to low frequencies of music (bass and drums).
If the product is not responding to sound, increase the sensitivity. See Sound Sensitivity for
more information.
Custom Color
Mode
Custom Color mode sets a custom color by adjusting the individual colors in the product.
1. Press <MENU> repeatedly until U-- shows on the display.
2. Press <ENTER> and one of the following shows on the display (where XXX is a number
between 0 and 255:
•rXXX (red)
•gXXX (green)
•bXXX (blue)
•AXXX (amber)
•WXXX (white)
•PXXX (ultraviolet)
3. Press <ENTER> repeatedly to select a color.
4. Use <UP> or <DOWN> to find a value between 0–255.
NOTE: Selecting 0 will turn the color off.
5. Press <ENTER> to select the value.
6. Repeat steps 3 to 5 until the product displays the desired color.

Page 17 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Infrared (IR)
Remote Control
Infrared functionality of the SlimPAR™ HEX 6 IRC allows the product to be controlled with an
infrared remote controller. The IRC-6 available from CHAUVET® can remotely set the product to
various modes, as well as adjust program speed and microphone sensitivity.
To turn on the infrared functionality, do the following:
1. Press <MENU> repeatedly until SET shows on the display.
2. Press <ENTER> and On or OFF shows on the display.
3. Press <UP> or <DOWN> to select On (turns on IR functionality) or
OFF (turns off IR functionality).
4. Press <ENTER>.
IRC-6 Operation
The IRC-6 infrared remote control works only when it is pointed directly at the product and there is
nothing in between the remote and the product. If the products are spaced far apart,
the remote
might need to be pointed at each product.
The next section describes how to use the IRC-6.
Auto Program Mode
Auto Program mode enables the auto programs on the product.
To use Auto Program mode, do the following:
1. Press <AUTO> on the IRC-6.
2. Press <+> or <–> to choose an auto program.
To adjust the speed of the auto program, do the following:
1. Press <SPEED> on the IRC-6.
2. Press <+> or <–> to increase or decrease the speed of the auto program.
Sound-Active Mode
Sound-Active mode enables the sound-active programs.
To use Sound-Active mode, do the following:
1. Press <SOUND> on the IRC-6.
2. Press <+> or <–> to choose a sound-active program.
To adjust the sound sensitivity in Sound-Active mode, do the following:
1. Press <SENSITIVITY> on the IRC-6.
2. Press <+> or <–> to either increase or decrease sound sensitivity.
Manual Color Selection
Manual color control enables selection of the 9 colors preprogrammed into the IRC-6.
To choose a specific color with the IRC-6, do the following:
1. Press <MANUAL> on the IRC-6.
2. Press any number between <0> and <9> to choose a color.
Manual Color Control
Manual color control enables individual adjustment for each color in the product.
To manually control the RGBAW+UV colors, do the following:
1. Press <MANUAL> on the IRC-6.
2. Press <R>, <G>, <B>, <A>, <UV>, or <W> (red, green, blue, amber, ultraviolet, or white) to
choose your color.
3. Press <+> or <–> to increase or decrease the amount of the color.

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 18 of 24
IRC-6 Operation cont.
Strobe
Strobe enables a variable strobe. Any program or color can be made to strobe. The product will
strobe as it goes through the Auto Program or Sound-Active modes.
To enable, and adjust the rate of, the strobe, do the following:
1. Press <STROBE> on the IRC-6.
2. Press <+> or <–> to increase or decrease the strobe rate.
To turn the strobe off, press <STROBE>.
Fade
Fade limits the Auto mode to the two programs that fade from color to color.
To enable fade, do the following:
1. Press <FADE> on the IRC-6.
2. Press <+> or <–> to toggle between the two auto programs with fade.
To exit fade and return to snap with access to all auto programs, do the following:
1. Press <AUTO>.
2. Press <+> or <–> to select an auto program.
Blackout
Blackout stops the signal from the IRC-6 to the product causing the product to go dark.
To black out the product, press <BLACKOUT> on the IRC-6.
To bring the product back on, press <BLACKOUT> on the IRC-6.
The IRC-6 will not respond to any inputs when Black Out is activated.
If the remote does not respond when a button is pressed, try pressing <BLACK OUT>. You
may have inadvertently activated Black Out.

Page 19 of 24 SlimPAR™ HEX 6 IRC User Manual Rev. 3
Master/Slave
Configuration
Master/Slave configuration allows a single SlimPAR™ HEX 6 IRC (the master) to control the actions
of one or more SlimPAR™ HEX 6 IRCs (the slaves) without a DMX controller.
In Master/Slave mode the master is set to operate in Auto Program, Sound-Active, or Infrared mode
and the slaves are set to operate in Slave mode.
The master and slaves are daisy chained though their DMX In and Out sockets
with the master
being the first product at the beginning of the chain. See DMX Linking for
an illustration of the
products in a daisy chain.
Once set and connected, the slaves will operate in unison with the master.
•The master is the first product in the DMX daisy chain.
•Never connect more than 31 slaves to the master.
•Never connect a DMX controller to a DMX daisy chain of master and slaves.
•Configure all the slaves before connecting the master to the DMX daisy chain.
Configuring the
Slaves
Configure the slaves for Slave mode before or after they are put in position, but before they are
daisy chained to the master.
To configure a slave, do the following:
1. Press <MENU> repeatedly until any DMX personality shows on the display.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to set the DMX address to d 1.
4. Press <ENTER>.
Configuring the
Master
Configure the master after all the slaves are connected to it and configured into Slave mode.
To configure the master, do the following:
1. Make sure the product is connected to a power source and connected to all the slaves.
2. Use the control panel to set the product into any of the standalone modes described in
Standalone Configuration.

SlimPAR™ HEX 6 IRC User Manual Rev. 3 Page 20 of 24
Settings
Configuration
The SlimPAR™ HEX 6 IRC can be customized with settings for program speed, sound sensitivity
and dimmer speed. Below are instructions for configuring the settings available in the
SlimPAR™
HEX 6 IRC.
Program Speed
Program speed sets the speed of the auto programs.
To set the auto program speed, follow the instructions below:
1. Press <MENU> repeatedly until S-- shows on the display.
2. Use <UP> or <DOWN> to select the desired program speed.
3. Press <ENTER>.
Sound Sensitivity
Sound sensitivity sets the sensitivity level of the microphone.
To set the sound sensitivity, follow the instructions below:
1. Press <MENU> repeatedly until SenS shows on the display.
2. Use <UP> or <DOWN> to select the desired sound sensitivity level.
3. Press <ENTER>.
Dimmer Mode
Dimmer mode sets the speed of the dimmer.
1. Press <MENU> repeatedly until dIM shows on the display.
2. Use <UP> or <DOWN> to select the desired Dimmer mode.
3. Press <ENTER>.