Chicago Electric 42292 User manual

BABA
BABA
BATTERTTER
TTERTTER
TTERY FLOAY FLOA
Y FLOAY FLOA
Y FLOAT CHARGERT CHARGER
T CHARGERT CHARGER
T CHARGER
OPERAOPERA
OPERAOPERA
OPERATING INSTRUCTIONSTING INSTRUCTIONS
TING INSTRUCTIONSTING INSTRUCTIONS
TING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2000 by Harbor Freight Tools®. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
42292
®

Battery Float Charger
The Battery Float Charger is used for the
maintenance of wet or gel cell batteries that are
stored or used periodically in such items as
boats, cars, snowmobiles, ATVs, and tractors.
The Float Charger prevents self discharge of
the battery, while maintaining and extending the
life of rechargeable 12 volt batteries. It
maintains a battery charge for batteries rated
from 5 to 125 amp-hours, by providing a
constant (minimum current) 13.5 VDC
regulated output. Other types of chargers
provide a strong, rapid charge but tend to boil
out liquids and decay electrodes.
It is simple to use. Hook it up, plug it in and
forget it.
Safety Warnings and Precautions
❑Do not make connections to battery
near open flame, sparks, or when
smoking.
❑Make connection to battery before plugging
charger into electrical outlet.
❑To prevent damage to charger, connect cable
clips to proper terminals on battery: black clip
to negative (–), red clip to positive (+).
❑Do not touch clips together while charger is
plugged in.
❑Do not place charger or electrical hookups
on ground or floor.
❑Do not turn on equipment that battery is
connected to while charging.
❑Remove charger power module from
electrical outlet, and disconnect the battery
clamps when finished.
❑Do not pull power cord to remove power
module from electrical outlet.
Specifications
Operation
1. Place Float Charger within 3 feet of battery.
2. Connect Red clip to positive (+) terminal of
battery.
3. Connect Black clip to negative (–) terminal
of battery.
4. Plug power module into electrical outlet.
Caution: If the Parts Box (#F) is to be mounted
on a sub-plate, do not use a power driver. To
mount the Parts Box, use the included 2 rubber
washers and 2 Phillips head screws and hand
tighten into place.
SKU 42292 Page 2
Battery Float Charger: 12 volts DC, 5 to 125
amp hours
Voltage Output: 13.5 VDC
Dimensions: 1-3/4 x 1-1/2 x 2-1/4 inches
Total length from power module to connector
clips: 53 inches
Input Voltage: 120 volts AC, 60 Hz, 14 watts
Remove battery cell caps before charging.
Caution: Make sure battery is vented (if battery is
maintenance free and non-fillable, it has vent slots -
make sure vents are clear and dirt free.
Always remove battery from vehicle before charging.
Use this product in accordance with the battery’s
and vehicle’s manual recommendations, safety
warnings and charging instructions.
Caution: Never charge battery in an enclosed area.
Never leave charger unchecked for such periods
of time as to create a hazard.
Caution: Surges and sparks in electrical power
supply could possibly cause battery explosion.
Battery charger should be plugged into a surge
protector outlet.
Caution: Batteries can explode under certain
conditions; excessive heat and/or poor
ventilation can cause battery explosion.
Safety Warnings and Precautions (continued)
REV 07/02; 05/03; 02/05 REV 10/05

Parts Listing Parts Diagram
Part # Description Qty
A Lid 1
B Power Cord 1
C Transformer 1
D Body 1
E Pin 2
F Parts Box 1
G Radiator 1
H Cover 1
I Pan Screw 2
J Circuitry 1
K Battery Cables 1
L Battery Clips 2
SKU 42292 Page 3
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS
PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYERTHAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT
ORTHAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND
PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
K
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.