Chicago Pneumatic CP310 9-19 User manual

W ARNING - AV ERTISSEMENT - ADV ERTENCIA - W ARNUNG - AV V ISO -
AV ISO - V AROITUS
To reduce the risk of inj ury, before using or servicing tool, read and understand the following
information as well as separately provided safety instructions (Item number: 6159948 750).
The features and descriptions of our products are subj ect to change without prior notice.
Erick son V ersion
Cnomo V ersion
Erick son V ersion
CP310 9-19 / CP310 9-24 / CP310 9-28 / CP3119-12 / CP3119-15 / CP3119-18 /
CP3119-22 / CP310 9-19ES / CP310 9-24ES / CP310 9-28 ES / CP3119-12ES /
CP3119-15ES / CP3119-18 ES / CP3119-22ES / CP3119-12EL / CP3119-12EXL
Cnomo V ersion
CP3119-12 / CP3119-15 / CP3119-18 / CP3119-22 / CP3119-12ES / CP3119-
15ES / CP3119-18 ES / CP3119-22ES

Item Part no Q ty Description
8 5
8 7
8 6
38
8 5 6153961660 1 Complete silencer kit
8 6 6158 702 100 1 Inlet hose assembly L= 67” (1.7m)
8 7 6158 751160 1 Reinforced cloth- lined exh aust hose L= 30”
(0.75m)
38 61552 6052 0 1 ollet Ø 4” on 
38 61552 60530 1 o 4 on 
38 61552 60540 1 o  on 
38 61552 60550 1 o  on 
100 61552 30190 1 Collet- holder ex tension
35 61552 6048 0 1 CNOMO collet Ø 3mm
35 61552 60500 1 CNOMO collet Ø 1/ 8 ” (6.35mm)
35 61552 60510 1 CNOMO collet Ø 8 mm
Routers
CP310 9-XX, CP3119-XX Item Part no Q ty Description
104
103
108
109
105
106
107
103 6153962 8 90 1 Machined routing kit
104 6155952 450 1 Flange
105 6156071450 1 Adj usting nut
106 615542 132 0 1 Router nose
107 615542 1312 1 Machined routing guide
108 61568 70560 1 Circlip
109 615758 12 70 1 Ball bearing
Dust ex traction system
CP310 9-XX, CP3119-XX Item Part no Q ty Description
110
111
115
113
110
112
114
110 6153960130 1 Suction cap
111 6158 600510 1 Diamond burr Ø 7.2 mm shank Ø 6mm
(Max. 2 8 000 tr/ min)
112 6158 600030 1 Diamond cylinder Ø 1- 1/ 16” shank Ø 6mm
(Max. 2 0000 tr/ min)
113 61539602 30 1 Suction cap
114 6158 600040 1 Diamond cylinder Ø 52 mm shank Ø 6mm
(Max. 15000 tr/ min)
115 6153960140 1 Suction cap
OPTIONAL ACCESSORIES
100
35
2 050541043
Issue no: 04
Series: C

Tool Co. LLC
All rights reserved. Any unauthorized use
or copying of the contents or part thereof
is prohibited. This applies in particular to
trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any
damage or malfunction caused by the use of
unauthorised parts is not covered by Warranty or
Product Liability.
INSTRUCTIONS
This product is designed for removing
material using abrasives. No other
use permitted. For professional use
only. Before servicing the power tool,
the supply of compressed air must be
disconnected or shut off.
When disposing of components,
lubricants, etc … ensure that the
relevant safety procedures are carried
out.
The tool is designed for a working
pressure of 6.3 bar (90 psig). The
compressed air must be clean. The
installation of a filter is recommended.
or maximum efficiency and
performance, comply with the
specification of the air hose (antistatic
hose). (efer to figure no.1 for
compressed air connection).
A mini  1mm (38")
B: 7 m max.
A
B
To obtain maximum efficiency from the
pneumatic tool, preserve its features
and avoid repeated repairs, a routine
inspection and repair programme
are recommended at least every 500
hours, the intervals between the
various inspections depending on the
amount of exertion on the power tool.
For dust extraction, please contact
your local sales.
Check the free speed of the tool
at regular intervals and after each
operation or maintenance task. Remove
the abrasive to check the speed. The
max imum allowed speed shown on the
tool must not be ex ce eded and the
vibration level must not be ex ce ssive.
This tool is fitted with blades which can
operate without lubricated air. However,
a small amount of oil allows the tool to
provide full power and lengthens its life.
The use of dry air with no trace of oil may
reduce the life of blades.
Declaration of noise and vibration emission
All values are current as of the date of this
publication.
These declared values were obtained by
laboratory type testing in accordance with the
stated standards and are suitable for
comparison with the declared values of other
tools tested in accordance with the same
standards. These declared values are not
adequate for use in risk assessments and
values measured in individual work places may
be higher. The actual ex posure values and risk
of harm ex perienced by an individual user are
unique and depend upon the way the user
works, the workpiece and the workstation
design, as well upon the ex posure time and the
physical condition of the user.
We, Chicago Pneumatic, cannot be held liable
for the consequences of using the declared
values, instead of values reecting the actual
ex p osure, in an individual risk assessment in
a work place situation over which we have no
control.
This tool may cause hand- arm vibration
syndrome if its use is not adequately managed.
We recommend a programme of health
surveillance to detect early symptoms which
may relate to noise or vibration ex posure, so
that management procedures can be modified
to help prevent future impairment.
2 050541043
Issue no: 04
Series: C
Original instructions.
© Copyright 2017, Chicago Pneumatic

DISASSEMBLY AND REASSEMBLY
INSTRUCTIONS
Disconnect the machine from the
compressed air supply.
Remove all accessories.
CP3119-12EL, CP3119-12EXL
●Unscrew the front housing (45) and the
intermediate housing (43).
●Disassembling the collet spindle assembly
(see figure 2).
● Unscrew the plug (52) before extracting the
spindle, being careful with the needles.
Disassembling the turbine
●Remove the turbine from its housing (15),
and pull out the lock ring (28 or 31).
●Unscrew the speed governor (17) or the
screw (16).
Left thread (see figure 3).
● Disassemble the turbine (see figure 4).
●CLAMP THE ROTOR SLIGHTLY IN A VICE
FITTED WITH LEAD JAWS, then unscrew
the coupling fork (41) or the collet holder
(37).
Reassembling the turbine
●Proceed in reverse order with respect to
disassembly.
Be careful with the direction for
assembling the blades.
● Apply a small quantity of "LOCTITE 243" on
the thread of the governor (17) or screw (16)
before tightening the governor to a torque of
2 N.m.
●Make sure that the turbine is correctly
positioned (see figure 5).
CP3119-12EL, CP3119-12EXL
Reassembling the complete collet holder:
●Proceed in the reverse order with respect to
disassembly.
●Grease the collet holder (49) before
positioning the needles.
LIMITED GUARANTEE
1. This Chicago Pneumatic product is
guaranteed against defective workmanship
or materials, for a maximum period of 12
months following the date of purchase from
Chicago Pneumatic or its agents, provided
that its usage is limited to single shift
operation throughout that period. If the usage
rate exceeds that of single shift operation,
the guarantee period shall be reduced on a
prorata basis.
2. If, during the guarantee period, the product
appears to be defective in workmanship or
materials, it should be returned to Chicago
Pneumatic or its agents, together with a short
description of the alleged defect. Chicago
Pneumatic shall, at its sole discretion,
arrange to repair or replace free of charge
such items as are deemed faulty by reason of
defective workmanship or materials.
3. This guarantee ceases to apply to products
which have been abused, misused or
modified, or which have been repaired using
other than genuine Chicago Pneumatic spare
parts or by someone other than Chicago
Pneumatic or its authorized service agents.
4. Should Chicago Pneumatic incur any
expense correcting a defect resulting from
abuse, misuse, accidental damage or
unauthorized modification, they will require
that such expense shall be defrayed in full.
5. Chicago Pneumatic accepts no claim for
labour or other expenditure made upon
defective products.
6. Any direct, incidental or consequential
damages whatsoever arising from any defect
are expressly excluded.
7. This guarantee is given in lieu of all other
guarantees, or conditions, expressed or
implied, as to the quality, merchantability or
fitness for any particular purpose.
8. No one, whether an agent, servant or
employee of Chicago Pneumatic, is
authorized to add to or modify the terms of
this limited guarantee in any way.
4 521
10mm
3
2 050541043
Issue no: 04
Series: C
Check out the collection of pneumatic grinders we offer.