CHIEF Pole Clamp Accessory FSA-1017 User manual

INSTALLATION INSTRUCTIONS
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX [phone]
8401 EAGLE CREEK PARKWAY, STE 700
SAVAGE, MINNESOTA 55378 USA
8807-000042
©2005 Chief Manufacturing
www.chiefmfg.com
12/05
BEFORE YOU BEGIN
Pole Clamp Accessory
Model: FSA-1017
The FSA-1017 Pole Clamp Accessory is used to provide
a means for attaching a desktop or wall mount to a
1 1/2" to 2" pole.
CAUTION!
To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be
attached to it, thoroughly study all instructions and illustrations before you begin the installation.
• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.

Model: FSA-1017 Installation Instructions
2
INTRODUCTION
TOOLS REQUIRED FOR INSTALLATION
• 5/32" Hex Key (provided)
INSPECT MOUNT BEFORE ASSEMBLY
Carefully inspect components for shipping damage . If
damage is apparent, call your carrier claims agent and do
not continue with installation until the carrier has
reviewed the damage.(see Figure 1)
Figure 1: PARTS
EXISTING MOUNT PREPARATION
Prior to installing the FSA-Pole clamp, the existing mount
has to be modified.
To prepare the existing mount:
1. Remove display, if present, from existing mount
following the instructions supplied with mount.
2. Loosen button head cap screw securing swing arm to
baseonexistingmountusinga5/32"hexkey(40).
(see Figure 2)
3. Uninstall button head cap screw, one nylon washer,
andtwo flatwashersfrom swing arm and set aside for
reuse. (see Figure 2)
4. Lift swing arm up and off of pivot pin and set aside for
reuse. (see Figure 2)
5. Removelargenylon washer,pivot pin, and Nylocknut
from existing mount base and set aside for reuse.
(see Figure 2)
Figure 2: Remove Mount from Existing Base
POLE CLAMP INSTALLATION
1. Insert Nylock nut (previously set aside) crown down
into front half of pole clamp. (see Figure 3)
Figure 3: Insert Nylock Nut
Table 1: Parts
Ref. Description QTY
10 CLAMP, Front, Pole Mount 1
20 CLAMP, Rear, Pole Mount 1
30 SCREW, Button Head Cap, 3
40 KEY, Hex, 5/32" (not shown) 1
10 20
30
Flat Washer
BHCS
Flat Washer
Nylon Washer
Nylock Nut
Swing Arm
Large Nylon Washer
Pivot Pin
Existing Mount Base
Nylock Nut
(10)

Installation Instructions Model: FSA-1017
3
NOTE: The following steps reuse hardware set aside
during existing mount preparation.
2. Place large Nylon washer into seat in pole mount
front. (see Figure 4)
3. Slide pivot pin through large nylon washer and down
into pole mount front. (see Figure 4)
4. Slide swing arm assembly down onto top of pivot pin.
5. Assemble two flat waskhers and one nylon washer
onto button head cap screw. (see Figure 4)
6. While holding Nylock nut, previously installed into
pole mount front, slide button head cap screw with
washersthroughswingarmanddownintopolemount
front until contact with Nylock nut is made.
7. Secure swing arm to pole mount front by screwing
button head cap screw into nylock nut.
NOTE: It may be necessary to move Nylock nut slighty
in order to allow button head cap screw to
properly seat in nut and allow tightening.
Figure 4: Install Swing Arm to Front Pole Mount
8. Place pole mount front with swing arm against pole in
approximate mounting location.
9. Place three BHCS (30) into pole mount rear (20) and
place against pole aligning with mount front (10).
10. Secure pole mount rear (20) to pole mount front (10)
and pole by tightening three BHCS (20) using 5/32"
hex key.
Figure 5: Mount FSA-1017 with Swing Arm on Pole
ADJUSTMENTS
The FSA-1017 allows for both vertical and horizontal
position adjustment on pole.
To adjust FSA-1017 position:
1. Loosen single (right) rear BHCS (30). (see Figure 6)
2. Move FSA-1017 to desired position. (see Figure 6)
3. Tighten BHCS (30).
CAUTION!
ALWAYS use two people when adjusting FSA-1017
position.
Figure 6: Pole Mount Adjustment
Flat Washer
Phillips BHCS
Flat Washer
Nylon Washer
Swing Arm
Large Nylon Washer
Pivot Pin
Pole Mount
(Front)
Recessed Seat
Pole Mount front (10)
with Swing Arm
(30)
Pole
(20)
View From Rear
Adjustment Screw

Model: FSA-1017 Installation Instructions
4