Child Craft Crib'N'Double 31001 User manual

1
Crib‘N’Double beD CoNverts
to toDDler beD or Full size
HeaDboarD & FootboarD
31001
assembly DireCtioNs aND Parts list
Directions for Maintenance, Cleaning, Storage and Use of your Crib/Toddler Bed are also included.
BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.
YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CRIB/TODDLER BED:
3Flat Tipped Screwdriver 3enclosedAllen Wrenches (A & B)
Parts eNCloseD iN HarDware bag
tHis is tHe assembly iNstruCtioNs
For Cribs solD iN tHe uNiteD states
Division of Foundations®Worldwide, Inc.
(12) Allenhead Bolts
C
(1) Allen Wrench
B
(1) Allen Wrench
A
(6) Allenhead Bolts
D (4) Allenhead Bolts
E
(17) Allenhead Bolts
F
(16) Allenhead Bolts
J (2) Allenhead Bolts
K
(20) Connector Nuts
I
(16) Joint Connector Nuts
H
(2) Joint Connector Nuts
G
•5216 Portside Dr, Medina, OH 44256 USA •PH: 877.716.2757 (U.S. Only) or 330.722.5033 •FAX: [phone]
•www.childcraftbaby.com
SI648E

2
Parts eNCloseD iN CartoN
Pouches
(storage for Assembly Directions)
(1) Long Foot Assembly
L (1) Short Foot Assembly
M (1) Short Head Assembly N
(1) Short Foot Cap Rail
O (1) Short Head Cap Rail
P
(1) Stationary Post - Left
S (1) Stationary Post - Right T
(1) Long Foot Cap
U (1) Spring
V
(1) Stretcher
(For use on Toddler Bed Only)
W
(2) Post Caps
(For use on Toddler Bed Only)
X
(1) Guard Rail Extender
(For use on Toddler Bed Only)
Y
(1) Stationary Side Assembly
Z
Q (1) Foot Post - Left R (1) Foot Post - Right

3
PreParatioN
Attach Stationary Posts S& Tby inserting Joint Connector Nuts Hinto the locator holes in the back face near top end of Stationary Side
Assembly Zand into bottom of the bottom rail of Stationary SideAssembly Z. Unslotted end of Joint Connector Nut Hwill be inserted into
hole. At the same time, insert Allenhead Bolts Cand Das shown in the diagram through posts. Thread Allenhead Bolts into Joint
Connector Nuts H. It may be necessary to use a at tip screwdriver in the slot at bottom of Joint Connector Nut Hto rotate it. This will
allow proper alignment of its threads with the thread on the Allenhead Bolts. Leave slightly loose until all bolts have been installed. Then
tighten all bolts securely using Allen Wrench A.
steP 1 - Diagram 1: attaCHiNg statioNary Posts to statioNary siDe
NOTE: Tighten securely means a good
snug t, do not allow the heads of bolts
and screws to dig into the wood.
T
Z
These holes have a
large counterbore on
the opposite face.
H
C
H
S
H
C
Locate and place Dowel Pin
on end of Stationary Side Z
into this locator hole.
NOTE: Bolt D(which is
the longer bolt) will only
be installed in the lower
mounting holes.
D
Carefully remove and lay out all hardware and parts. Check quantities and match the Hardware List and the Parts List. NOTE:
During the assembly process whenever using screws or bolts, check each with the Hardware List by letter and size
identication. Place each screw or bolt on the diagram of the item which is sketched actual size. Be sure to use the proper size
specied in the assemblydirections.Ifanypartsaremissingorbrokenoryouneedassistancewithassembly,DONOTreturnthe product
toyourdealer.Call Foundations®for assistance at 877.716.2757 (U.S. Only) or 330.722.5033 (Monday through Friday, 9:00 a.m.– 4:00
p.m. Eastern Time). Please identify the Crib’n’Double Bed by the model identication number stamped on the inside face of short head or short foot
assemblies, available when you call or write us at: Foundations®, 5216 Portside Dr, Medina, OH 44256 USA. Make note of all
identication numbers and include this information with your request. DO NOT SUBSTITUTE PARTS! Record your model identication
number here for future identication: Model #________________________

4
steP 2 - Diagram 2: assemble CaP rails to sHort HeaD aND Foot assemblies
Position Short Head Cap Rail Pabove Short Head Assembly Nas shown. Insert dowel pins in top rail of Short Head Assembly Ninto
receiving holes located in the bottom face of Short Head Cap Rail P. Then install two (2)Allenhead Bolts Finto receiving holes in bottom
edge of top rail on Short Head Assembly Nand thread into metal inserts. Once threads are engaged, tighten securely.
Follow this same procedure to attach Short Foot Cap Rail Oto Short Foot Assembly M using two (2) more of Allenhead Bolts F.
steP 3 - Diagram 3: attaCHiNg Foot Posts to sHort HeaD aND Foot assemblies
Attach Foot Post - Left Qto Short HeadAssembly Nby inserting Allenhead Bolts Fthrough their locator holes in Short HeadAssembly N
and threading into threaded inserts in Foot Post - Left Q. Tighten all Allenhead Bolts Fsecurely using Allen Wrench A.
Repeat this step to attach Attach Foot
Post - Right Rto Short Foot Assembly M.
F
NOTE:TheWarning label
will be positioned here.
Observe the orientation
of Short Head Cap Rail P
which has a shaped
narrow end.
F
Large Counterbore
Here
Threaded Insert
P
F
Shaped area will
be on outside face.
NOTE: The Warning label will be positioned
here. Observe the orientation of Short Head
Cap Rail Pwhich has a shaped narrow end.
Dowel Pins Threaded metal
insert in bottom
face (2) Places.
F
Outside Face
N
Q
N

5
steP 4 - Diagram 4: attaCHiNg sHort HeaD assembly to statioNary siDe assembly
Attach Short Head Assembly Nto Stationary Side Assembly from Step 1. Allenhead Bolts Fwill be installed through receiving holes in
the end rail of Short HeadAssembly Nand threaded into the metal inserts installed in Stationary Post - Left S. Atotal of two (2) Allenhead
Bolts Fare required.
Repeat this step to attach Short Foot Assembly Mto Stationary Post - Right T.
steP 5 - Diagram 5: iNstalliNg loNg Foot assembly
D
S
T
Allow dowel pins on both ends of Long FootAssembly Lbottom rail to enter hole in posts Qand R. Joint Connector Nuts Hwill be installed
in the bottom edge of both the top and bottom rail of Long Foot Assembly Las each of the following bolts are installed (NOTE: Install
unslotted end of Joint Connector Nuts H into hole rst). Insert Allenhead Bolt Dthrough bottom hole in Foot Post Qand Rand into bottom
rail of Long Foot Assembly Land thread into Joint Connector Nut H as described in Step 1. Insert Allenhead Bolt Cinto the top hole and
also thread it into a Joint Connector Nut H. Tighten all bolts securely.Atotal of two (2) of Bolts Cand two of Bolts Dwill be used with four
(4) Joint Connector Nuts Hduring this process.
Stationary Side Assembly
from Step 1.
Z
Short Foot Assembly from
Step 3 (this part is shown
after installation).
M
N
Short Head Assembly
from Step 3.
NOTE: Allenhead Bolt D
is longer than Allenhead
Bolt C.
C
Insert dowel on end of
bottom rail of Long Foot
Assembly Linto post Q
and R.
Threaded Insert
F
H
H
F
L

6
steP 7 - Diagram 7: attaCHiNg sPriNg to Crib
Before installing Spring V, determine the height for installation. Pull out “SwingArms” to the appropriate angle as shown. With the help of
a friend, carefully lower Spring Vinto the assembled crib to the selected height. Insert Allenhead Bolts Jinto the mounting holes in the
“SwingArms” and through the locator holes in Short Head and FootAssemblies Mand N. From the outside of the assembled crib, insert
connector Nuts Iinto the locator holes and thread onto Allenhead Bolts J. Tighten securely using Allen Wrench Awith bolts Jand Allen
Wrench Bwith Connector Nuts I.A total of four (4) of Iand Jare used to attach Spring V. Also install Allenhead Bolts Jand Connector
Nuts Iin the spring mounting position holes not used at this time.
To adjust height of Spring V, unthread all of the Allenhead Bolts J
and Connector Nuts Iand move Spring Vto the other height location
shown on the diagram. Then follow the same process for attaching the
Spring Vat its now location by following the process described above.
steP 6 - Diagram 6: attaCHiNg loNg Foot toP CaP
Attach Long Foot Top Cap Uto the crib assembly by lowering it down on top edge of Long Foot Assembly L. Allow the dowel pins in the
top of posts Qand R to t into the two receiving grooves. Also carefully align dowel pins in the top edge of Long Foot Assembly Lto enter
receiving holes in bottom face of Long Foot Top Cap U. Install ve (5) Allenhead Bolts Fthrough bottom edge of top rail in the Long Foot
Assembly Land carefully thread into the metal inserts in Long Foot Top Cap Ubottom face. Once aligned, thread bolts into inserts and
tighten securely using Allen Wrench A.This hole at each end will
receive dowel pin in Long
Foot Assembly Ltop rail.
Groove will
receive dowel
pins on top of
posts Qand R.
Threaded Inserts
(5 places)
F
(5 places)
U
“Swing Arms” rotated at
45º angle as shown.
Second possible
height location of
Spring V(these will
also be lled with parts
Iand Jto prevent
nger entrapment
of child.
ISwing
Arm on
spring.
I
J
Text on pouches should
face up during installation.
L
M
N

7
InsertAllenhead Bolts Jand Connector Nut Iinto empty holes in posts.Also installAllenhead Bolts Ewith Connector Nuts Ithrough edge
of posts Qand R. Each allenhead bolt will be securely threaded into a Connector Nut Iand tightened securely. Use Allen Wrenches A
and B to securely threaded these items together. Filling these holes will add security to the crib by prevent nger entrapment for the child.
Before using crib, refer to page 12 and 13 for Warnings and maintenance of the crib.
steP 8 - Diagram 8: FilliNg emPty Holes
I
J
E
I
Receiving hole
through post Q
and R(2 total)
NOTE: This hole was
provided for the
attachment of a guard
rail (if desired) when crib
is converted to a Toddler
Bed.
Install two (2) of Iand J
through each of the (4)
posts as shown.
NOTE: These holes were
provided to allow the
conversion of the crib to
a full bed.
Q
R

8
When use as a crib has been completed, you have the option to convert to a Toddler Bed for years of additional use in your child’s room.
Remove mattress. Spring Vmust be installed in lowest position. Remove and store (see Storage on page 12) Long Foot Top Cap U
and Long Foot Assembly L. Refer to Steps 6 and 5 and perform these steps in reverse to remove these parts.
Store away all parts and hardware removed in the event you wish to convert your Toddler Bed to a Crib. DO NOT store extra hardware
in pouch attached to spring.
steP 9 - Diagram 9: CoNvert “Crib” to a“toDDler beD”
G
DW
Gently stretch posts Q
and Raway from each
other to allow space for
the dowels on Stretcher
W.
Insert dowel pin
on end of
Stretcher Winto
receiving hole in
posts Qand R.
Install Stretcher Wby gently stretching foot posts Qand Raway from each other just enough to allow wood dowels in the ends of Stretcher
W to t into the receiving holes in the posts Qand R. If this does not allow adequate room, then it may be necessary to temporarily unbolt
one of the bolts securing the Spring Vto the crib and reconnecting it once Stretcher Wis installed. InstallAllenhead Bolts D(just removed
during the removal of Long FootAssembly L) through receiving hole near bottom of posts Qand Rand thread into a Joint Connector Nut
Gwhich is to be installed in the bottom edge of Stretcher W(part Gis a part not previously used and should have been stored away once
the crib was assembled). Tighten bolts Dsecurely using Allen Wrench A.
Q
R
W
V

9
Align dowel pins in top of posts Qand Rwith holes in Post Caps Xand press Post Caps Xdown over dowel pins. Insert Allenhead Bolts
Kthrough hole in Post Caps Xand tighten securely into threaded insert in top of posts Qand Rusing Allen Wrench A.
steP 10 - Diagram 10: attaCH Post CaPs to Posts
KX
Q
Post Cap X shown
installed here.
Threaded Insert
Insert Allenhead Bolts Eand Connector Nuts Iinto the empty holes in posts Qand R. Tighten securely using Allen Wrench Aand B.
IMPORTANT! refer to warnings on page 10 before using as Toddler Bed.
steP 11 - Diagram 11: FilliNg emPty Holes iN Posts
E
I
(2) Empty holes in each
foot posts Qand R
(bolts and connectors
shown installed in this
post)
Q
R
Q
R

10
iNstalliNg a guarD rail
A Guard Rail can be purchased for added security. Follow the
directions on the instruction sheet included with the Guard Rail.
You will need (2) Guard Rail Extenders Yand (4) of Allenhead
Bolts Dfrom this crib.
Fill all empty holes in Foot Posts Qand Ras directed in Step 11.
ENTRAPMENT. Openings in and between bed parts can entrap head and neck
of a small child. NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
over bed. NEVER place items with a string, cord or ribbon, such as hood strings
or pacier cords, around a child’s neck. These items may catch on bed parts.
(1310 mm) in length, 27 1/4 in. (690 mm) in width, and 4 in. (100 mm) in thickness.
•The users maximum weight shall not be greater than 50 lbs. (22.7 kg).
•Mattress MUST be moved into lowest position for proper positioning behind
stretcher.
•This crib contains all components necessary to convert to a toddler bed. However,
a guardrail may be available for purchase to provide additional security. Contact
Foundations®for assistance. Refer to maintenance section for contact information.
!
!
!
!(For Toddler Bed)
!
WARNING
!
!
WARNING
!
:INFANTS HAVE DIED IN TODDLER BEDS FROM
!
!
WARNING
!
:STRANGULATION HAZARD: NEVER place bed near windows
where cords from blinds or drapes may strangle a child. NEVER suspend strings
CAUTION:
ENTRAPMENT HAZARD: To avoid dangerous gaps
any mattress used in this bed shall be a full-size crib mattress at least 51 5/8 in

!