Child Craft Folding Mini Wood Crib F61301 User manual

1
AB20046G
AB20046_G1
Foundations®Worldwide, Inc.
5216 Portside Dr, Medina Oh 44256 USA • PH: 1 330.722.5033 • FAX: [phone]
www.childcraftbaby.com
Folding Mini Wood Crib
ASSEMBLY ASSISTANCE
IMPORTANT: retain for future reference read
carefully.
Foundations®strives for the highest quality in our
products but occasionally a missing part or problem
can occur during assembly.
If any parts are missing or broken or you need
assistance with assembly, DO NOT return the
product to your dealer. Go to our website at
www.childcraftbaby.com or Call Foundations®
for assistance at 1-877-716-2757 (U.S. Only) or
1-330-722-5033 (Monday through Friday, 9:00
a.m.– 4:00 p.m. Eastern Time). Please have the
model number and manufacture date available
when you call or write us at:
Foundations®, 5216 Portside Dr. Medina Oh. 44256
Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE .
FOR CUSTOMER SERVICE CALL
1-877-716-2757
(outside of U.S. 330-722-5033). DO NOT CALL
RETAILER OR RESELLER FOR SERVICE
AS THEY ARE NOT AUTHORIZED TO
RESOLVE ANY SERVICE ISSUES.
FOR FEDERAL SAFETY STANDARD
COMPLIANCE CERTIFICATES, PLEASE VISIT
OUR WEBSITE AT
www.childcraftbaby.com
Record the information for your product here:
Model number:
Manufacture date:
PO number:
Models Covered: F61301.
• Adult assembly required.
• Read all instructions BEFORE assembly and USE
of product. KEEP INSTRUCTIONS FOR FUTURE
USE.
• Unpack carton, remove packing materials,
including poly bag. Identify and check all parts.
ASSEMBLY INSTRUCTIONS
THIS IS THE ASSEMBLY INSTRUCTIONS FOR CRIBS SOLD IN THE UNITED STATES

2
A. 6mm x 80mm Allen Head Bolt
B. 6mm x 60mm Allen Head Bolt
C. 6mm x 20mm Allen Head Bolt
D. Joint Connector 6mm Thread
E. Dowel 10mm Dia X 40mm
F. 6mm Connector Nut
G. 6mm Joint Connector
H. 6mm Connector Nut
I. 4 mm Allen Wrench
J. 6mm x 10mm Allen Head Bolt
K. Front Support Bracket
L. Mattress Support Bracket Right
M.Mattress Support Bracket Left
N. Stationary Side Assy (Back )
O. Stationary Post Left (Back)
P. Stationary Post Right (Back)
Q. Headboard Assembly
R. Front Assembly
S. Front Post - Right
T. Front Post - Left
U. Footboard Assembly
V. Mattress Support
W. 3” Mattress
X. Brace Block Right
Y. Brace Block Left
AA. 2” Locking Caster
BB. 2” Non Locking Caster
Hardware Package
AB20046_G3
O P Q
RT
SU
VX
Y
W
AA
BB
N
Crib Parts
PARTS LIST
Part Description Part Number Quantity
11200324
11200326
11200384
11200330
11200323
11200331
11200395
11200394
11200070
11200393
11200380
11200378
11200379
22301009
22301065
22301066
22301820
22301004
22301063
22301064
22301819
22301062
21100123
22301028
22301029
12100056
12100055
8
12
4
20
12
2
2
4
2
4
2
1
1
PREPARATION
Carefully remove and lay out all hardware and parts.
Check quantities and match the parts list. Construct
Crib on an even at oor.
Note: during the assembly process whenever
using screws or bolts, Check each with the parts list
by letter and size identication. Place each screw
or bolt on the diagram of the item which is sketched
actual size. Be sure to use the proper size specied
in the assembly directions. If any parts are missing
or broken or you need assistance with assembly
DO NOT return your product to the dealer.
Please identify the crib by the model number
identication stamped on the inside face of the
Stationary side assembly when you call or write to
Foundations®. Make note of all identification
numbers and include this information with your
request.
DO NOT Substitute Parts!
SUGGESTED TOOLS
#2 Medium Straight Screwdriver, Rubber Mallet
1
1
1
1
1
1
1
1
1
1
1
1
2
2
AB20046_G2
A
B
C D E
FG
I
JK
LM
H

3
Construct Front assembly:
Place dowel pin in end of top rail of Front Assembly
R into recieving hole in post during assembly.
Place Joint Connectors D into holes in the bottom
of the top and lower rails of Front Assembly R .
Insert 2, 80mm Allen Head Bolts A into Front Post
S . Align Front Post S with Front Assembly R .
Note: Post has 2 holes facing forward as shown in
Figure 2.
Rotate the Joint Connectors D to align threads with
Bolts. Thread Bolts A into Joint Connector D
Snug bolts with Allen Wrench I .
Repeat assembly with Front Post T .
Tighten all bolts securely.
See gure 2.
Figure 1
STEP 1
AB20046_G4
O
N
D
P
A
STEP 2
Construct Stationary Side (back) assembly:
Place Joint Connectors D into holes in the bottom
of top and lower rails of Stationary Side Assembly N
Insert 2, 80mm Allen Head Bolts A into Stationary
Post P .
Align Stationary Post P with Stationary Side
Assembly N .
Note: Post has 4 holes facing forward as shown in
Figure 1
Rotate the Joint Connectors D with a straight
screwdriver to align threads with bolts. Thread Bolts
A into Joint Connector D .Snug bolts with Allen
Wrench I .
Repeat assembly with stationary post O .
Tighten all bolts securely.
See gure 1.
Figure 2
R
T
D
A
AB20046_G5
S

4
Figure 3
STEP 3
Q
AB20046_G6
FK
C
B
E
Y
D
1
2
STEP 4
Figure 4
AB20046_G7
B
E
D
U
P
Q
Construct Headboard and Footboard assembly:
There are 2 positions for the Front Support Bracket
shown as lower 1 and upper 2 appropriate height
for the intended child as explained in warnings
section.
Insert screw in back side of Front Support Bracket
K into lower blind hole and align upper hole with
through hole in Headboard Assembly Q .
Note: lower screw does not fasten to the wood rail
and is there to prevent rotation of K .
Insert 20 mm bolt C through Bracket and
Connector Nut F through Headboard Assembly Q
and tighten with Allen Wrenchs I .
Insert 2 Wood Dowels E into Brace Block Y .
align with holes in headboard assembly Q and
push together.
Insert Joint connector D into bottom of Brace Block
and align the threads with a straight screwdriver to
accept the Bolt B . Thread B into D .
Tighten all bolts securely with Allen Wrench.
Repeat the above steps for the Footboard assembly
U and use Brace block X .
See gure 3.
Add Headboard and Footboard:
Insert 2 Wood Dowels E into blind holes on the
Foot Board Assembly U . Insert exposed end of
wood dowels E into recieving holes in stationary
post Right P . Insert 2 Joint Connectors D into
Footboard assembly (inside face of back rail) and 1
Joint Connector D into bottom of Brace Block. Align
Joint Connector threads with a straight screwdriver
to accept bolts.
Align Footboard Assembly with Stationary Side
Assembly (Back) and push together. Insert 3 bolts
B through Stationary Side Assembly (Back) and
snug bolts with Allen wrench.
Repeat assembly for Headboard Assembly Q .
After all bolts are in place tighten all securely.
See gure 4, shown from bottom view.

5
Figure 5
STEP 5
Add Front Assembly:
Insert 4 wood Dowels E into blind holes on
Headboard Assembly Q and Footboard Assembly
U . Insert Joint Connectors D into inside face of
Headboard Assembly Q and Footboard Assembly
U . Align Joint connector threads with a straight
screwdriver to accept Bolts B . Insert Bolts
B into Front Assembly and snug them.
After all bolts are in place tighten all securely.
See gure 5 shown from bottom view.
AB20046_G8
B
E
D
U
Q
AB20046_G9
H
J
L
V
Figure 6
STEP 6
Attach Mattress Support Brackets:
Note: Face of Mattress Support with warning sheet
applied must face upwards for the below procedure.
Align Mattress Support Bracket L with holes in
Mattress Support V making sure lip is under
Mattress Support V . Insert 2 of the 6 mm
Connector Nuts H from underneath through holes.
Place 6mm x 10mm Allen Head Bolts J through top
and snug together.
Repeat the above steps to attach Mattress Support
Bracket M to the opposite end of Mattress Support
V .
Tighten Screws and Connector Nuts securely with
Allen Wrenches.
See gure 6.

6
Figure 8
Figure 7
AB20046_G10
G
C
C
2
1
V
K
L
M
Add Mattress Support to crib.
There are 2 positions for the Mattress Support V
shown as lower 1 and upper 2 . Refer to warning
section to determine appropriate height for the
intended child. The position must be the same as
the position of the Front Support Brackets K .
The Mattress Support V is lowered into the crib
until the front rests on the Front Support Brackets K
Align the Mattress Support Brackets L and M with
the holes in the crib. Insert Joint Connector G into
hole in L and M from inside of crib then through
correct height hole in the crib. Thread Bolt C from
the outside into the Joint Connector G .
Tighten securely with Allen wrenches.
NOTE: Do not overtighten Bolt C and Joint
Connector G . They are designed to move
freely after being tightened to permit
Mattress Support to pivot.
See gure 7.
BB
AA
AB20046_G11
STEP 7
STEP 8
Add Casters to crib.
Place 2 Non Locking Casters BB in the Stationary
Side Assembly (Back). Place stem of Caster into
hole in bottom of leg and push until fully engaged.
Place 2 Locking Casters AA into Front Assembly.
Place stem of Caster into hole in bottom of leg and
push until fully engaged.
With the Casters in place use a rubber mallet or
similar tool and tap the Casters into the inserts until
the caster stem is fully engaged.
Note: Once the casters are fully engaged and
installed they cannot be removed without
damaging crib.
See gure 8 shown from bottom view.

7
Figure 9
AB20046_G12
1
2
2
FOLDING CRIB FOR STORAGE
Step 1 lift spring up with mattress.
Step 2 Fold sides in to close crib.
Step 3 Secure the crib in the closed position. Using
the Velcro loop fasteners attached on
the bottom of the Mattress Support V , wrap
the Velcro around the slats (spindles) in the
Front Assembly.
See gure 9.

8
Maintenance Cleaning and Storage
MAINTENANCE:
Upon completion of the assembly, check to make sure all screws, bolts and connectors are tightened and
secure.
Periodically check crib for damaged hardware, loose joints, missing parts or sharp edges before and after
assembly and frequently during use.
DO NOT use crib if any parts are missing or broken.
If any parts are missing, broken or you need Assistance DO NOT return crib to your dealer.
Call Foundations® at 330.722.5033 and include model identication numbers recorded on page 1.
DO NOT substitute parts.
CLEANING:
Mix a mild solution of gentle dishwashing soap and water, apply to surface using a clean cloth lightly
dampened in the solution. Rinse well with clear water using a soft clean cloth, then dry all surfaces with a
soft dry cloth.
DO NOT use abrasive cleaners or any cleaners with harsh chemicals that would contact a child’s
skin, scouring pads, steel wool or coarse rags. This crib should be treated the same as any ne
furniture.
STORAGE:
When storing crib use Caution as extreme temperature or humidity changes could be harmful.
Use caution when a vaporizer is in use. Always aim vapor stream away from crib as well as away
from any wood furniture item.
After completing the assembly the user is advised to read and be aware of ALL WARNINGS,
CAUTIONS, CLEANING, STORAGE USE AND MAINTENANCE notices in these directions and
printed on the top surface of Mattress Support. A pouch is attached to the underside of the
Mattress Suport for the permanent storage of the assembly directions. Please place the
complete set of assembly directions into the pouch for future referral. We caution the user to Not
place excess hardware in the pouch as it could present danger to the child if retrieved.
WARNING
Infants can suffocate if improperly fitted mattresses
or improperly fitted sheets are used. Use only
Foundations replacement mattresses and sheets.
To purchase properly fitting mattresses and sheets,
call 330-722-5033 or online at www.foundations.com
or contact your authorized Foundations dealer.
®
®

9
● The crib, including side rails, must be fully erected prior to use. Make sure latches are
secure.
● Strings can cause strangulation! NEVER place items with a string around a child’s neck
such as hood strings or pacifier cords. NEVER suspend strings over crib or attach
strings to toys.
● Discontinue use of the crib when child is able to climb out or reaches the height of 35
inches (89 cm).
● Child can become entrapped and die when improvised netting or covers are placed on
top of product. NEVER add such items to confine child in product.
● When child is able to pull to a standing position, set mattress to lowest adjustable
position and remove bumper pads, large toys and other objects that could serve as steps
for climbing out.
● NEVER place crib near window where cords from blinds or drapes can strangle a child.
● Use ONLY the mattress provided by the manufacturer (which must be at least
37 3/4 inches (96 cm) long by 23 3/4 inches (60.4 cm) wide and not more than 3 inches
(7.6 cm) thick.
● Always provide the supervision necessary for the continued safety of your child. When
used for playing, NEVER leave child unattended.
● To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
back to sleep, unless otherwise advised by your physician.
● NEVER use this product if there are any loose or missing fasteners, loose joints, broken
parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact
Foundations for replacement parts. Never substitute parts.
● NEVER use plastic shipping bags or other plastic film as mattress covers not sold
and intended for that purpose. They can cause suffocation.
● NEVER use a water mattress with this crib.
● If renishing, use a non-toxic nish specied for children’s products.
● DO NOT use crib near objects that child could reach or pull into crib and cause injury
such as lamps, heaters, fireplaces, or ironing boards.
● To avoid injuries, do not allow children to climb or play on or under the crib.
Meets CPSC
Safety Requirements
5216 Portside Dr.
Medina Ohio 44256 USA
Telephone: [phone]
Fax: [phone]
www.childcraftbaby.com
WARNING
Infants can suffocate
• In gaps between a mattress too small or too thick and sides of crib.
• On soft bedding. NEVER add a mattress, pillow, comforter or padding.
WARNING
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY OR DEATH.