Child Craft F02102 User manual

Model Covered: F02102
Long Beach 4 Drawer Chest
F02102.59
2018 / 12
10861
AB20302A
White
Light Gray
Dark Gray
White

AB
D
C
E
H
F
J
IKL
AA
Z
Y
BB
A. End Panel - Left 92103436 1
B. End Panel - Right 92103437 1
C. Top Front Rail 92103438 1
D. Front Rail 92103439 1
E. Bottom Front Rail 92103440 1
G. Back Panel
92103441 1
F. Top Panel
92103442 2
H. Lower Back 92103443 1
I. Drawer Front 92103444 4
J. Drawer Back 92103445 4
K. Drawer Bottom 92103446 4
L. Drawer Right Side 92103447 4
M. Drawer Left Side 92103448 4
92103449 28
N. Dowel Ø8
92103449 12
O. Dowel Ø6
92103449 44
P. Flat Head Screw
92103449 6
Q. Minifix Screw
92103449 30
R. Flat Head Screw
92103360 32
S. Glide Screw
92103449 6
T. Minifix Round Nut
92103360 4
U. Glides
92103450 8
V. Handle
92103450 16
W. Handle Screw
92103361 1
X. Union Plastic
92103359 2
Y. Pan Head Screw
92103359 2
Z. Pan Head Screw
92103359 2
AA. Bracket
92103359 1
BB. Restraint Strap
2
Carefully remove and lay out all hardware and parts.
Check quantities and match the parts list.
Construct case on an even flat floor.
Note: during the assembly process whenever using
screws or bolts, check each with the parts list by letter
and size identification.
Be sure to use the proper size specified in the assembly
directions. If any parts are missing or broken or you need
assistance with assembly.
DO NOT return your product to the dealer. Please
identify the furniture by the model number identification
stamped on the assembly when you call or write to
Foundations. Make note of all identification numbers and
include this information with your request.
DO NOT Substitute Parts!
G
M
Anti-Tip Kit Parts
Hardware Package
NOP
QRST
U-W
U-X U-Y U-Z
VW
X

NH
N
Q
(6x)
O
O
O
O
C
D
E
Q
O
O
O
O
O
O
O
O
N
N
N
N
N
N
L
N
N
N
M
Q
F
N
N
B
Q
Q
N
N
N
A
Q
Q

S
U-Z
S
U-Z
B
Y
AA-W
A
U-W
S
S
U-Z
S
S
U-Z
S
S
U-Z
B
S
S
U-W
S
S
U-W
S
S
U-W
S
A
S
S

T
P
T
(2x)
T1st
2nd
P
B
C
D
E
P
P
P
H
(2x)

P
T
T
P
P
(3x)
P
(2x)
T
P
P
A
A

T
T
P
F
PP
G
G
7
P
P
T
(2x)
(2x)
P
STEP 8
STEP 9
(30x)
R
X
G
G

P
S
S
S
U-Y
U-X
V
8
w
K
P
P
P
L
M
P
P
P
J
S
S
S
U-Y
w
V
w
w
V
w
w
STEP 10 (2x)
( I ) White

P
S
S
S
U-Y
U-X
V
9
w
STEP 11 (2x)
K
P
P
P
L
M
I
P
P
P
J
S
S
S
U-Y
w
V
w
w
V
w
w

FURNITURE
FRAME
FURNITURE
FRAME
FURNITURE
FRAME
WALLBOARD
BB
AA
WALLBOARD WALLBOARD
Y
YAA
Z
AA
Z
STEP 12
10
ANTI-TIP RESTRAINT ASSEMBLY INSTRUCTION
Anti-tip Restraint Assembly is REQUIRED in order to complete construction of this product.
When properly installed, this hardware can provide additional protection against the unexpected tipping of
furniture.
ASSEMBLY INSTRUCTIONS:
1) Attach one bracket ¨AA¨ to back of unit using ( 2 ) of screw ¨Z¨ as shown in diagram below.
2) Place the furniture against wall at the desired location in your room. Mark the location on the wall which will
position a second bracket ¨AA¨ approximately 1" lower than the one attached to the unit.
3) Remove furniture from desired location to allow installation of a second bracket ¨AA¨ on wall.
Attach the second bracket ¨AA¨ to the wall. Note-if a ¨Hollow Wall Anchor Bolt¨ system (not provided) is
used, it will be necessary to purchase a type that is appropriate for your wall construction and will also
be compatible with bracket ¨AA¨.
If bracket ¨AA¨ is mounted into a wall stud then it may be necessary to bore a 5/64" diameter x 1" deep
pilot hole into the wall at the location of each of the 2 screw holes in bracket ¨AA¨. This will assist in an
easier installation of the 2 screws ¨Y¨.
4) Move furniture back into the desired location approximately 3" away from the wall.
5) Lace an end of the nylon restraint strap ¨BB¨ through each bracket. Bring both ends together and
slide the beaded end of the strap through the keyhole shaped slot on the other end. Pull down on the
beaded end until it snap-locks into the keyhole.
6) Move furniture against wall and continue to adjust nylon restraint strap to
secure unit snugly against wall.
7) Check to make sure the strap is securely laced and locked to the
brackets.