Childcare Swift Car Red 022012-012 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
Swift Car
Walker “Red”
Model # 022012-012

Use only accessories as recommended by the supplier.
ALWAYS use the safety locks once the walker height is correctly adjusted.
Check that all safety locks are engaged before placing child in the walker.
This walker should not be used by a child who can walk unaided.
This walker should not be used by a child weighing less than 7kgs and 65cm in height.
A child should discontinue using this walker when weighing more than 11kgs and 80cm in height.The walker is not
suitable for babies under 6 months of age.
Electrical cords, heaters, replaces and other hot objects, or any other objects or substances that may be dangerous,
should be guarded or put out of reach of a child using the walker.
Promptly replace any broken parts.
The walker should not be used (whether indoors or outdoors) on surfaces that have any obstructions that could cause
the walker to tip over.
The walker should not be carried with a child in it.
Adjust the height of the walker so that both feet of a child in the walker should be able to touch the ground.
Care must be taken while folding and unfolding the walker to prevent ngers being caught.
Read all instructions before assembly and use of the walker. Keep
instructions for future use.
BEFORE ASSEMBLINGTHIS WALKER, READ AND UNDERSTANDTHE INSTRUCTIONS.
Never leave a child unattended.
Always keep child in view while in walker.
Only use on at surfaces free of objects that could cause the walker to tip over.
To avoid burns, keep the child away from hot liquids, ranges, radiators, space heaters and
replaces etc...
Do not use the walker if it is damaged or broken.
Do not use until baby can sit up by itself.
To avoid serious injury or death,block stairs/steps securely before using walker.
Clean (friction components) regularly to maintain stopping performance.
Remove packaging from walker vicinity after it’s assembly.
KEEP INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
SAFETY PRECAUTIONS
WARNING
WARNING - STAIR HAZARD
AVOID SERIOUS INJURY OR DEATH:BLOCK STAIRS/STEPS SECURELY BEFORE USING WALKER.

Battery Safety Information
In exceptional circumstances, batteries leak uids that can cause a chemical burn injury or ruin your product.To avoid
leakage:
• DO NOT mix old and new batteries or batteries of different types: alkaline, standard (carbon zinc) or rechargeable
(nickle-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.
• ALWAYS remove exhausted batteries from the product.
• Dispose of batteries safely.
• DO NOT dispose of this product in a re.The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same equivalent type,as recommended.
• DO NOT charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable,rechargeable batteries are used,they are only to be charged under adult supervision.
SAFETY PRECAUTIONS
Keep medication,strings,elastics and small toys out of reach from any position of the walker.
ALWAYS attach the toys tightly to the walker according to the instructions.Check frequently.
This walker should be used only for short periods of time eg:20mins

Due to variations in the style and design of our products, the photographs and illustrations shown in this
instruction manual are generic,therefore product fabrics,colour and design may vary from images shown.
CNP Brands reserves the right to alter product specications without notice as a result of our ongoing
policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Swift Car Walker
Congratulations on your purchase of the Swift Car
Walker“Red”
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to read
this manual carefully before using this product and keep it in a
safe place for future reference.
CONGRATULATIONS

ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the
box against the list below. If anything is missing, please contact
Customer Service.
InAustralia,contact CNP Brands on 1300 667 137,in New Zealand
contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
There are no accessories recommended for use with this Childcare Walker.
Main frame
Toy tray
Rear spoiler
Side mirror
x 1
x 1
x 1
x 2
x 1
x 1
x 2
x 2
Seat pad
Seat support
Rear wheel
Front castor

ASSEMBLY CONTENTS / ASSEMBLY / OPERATING INSTRUCTIONS
Supplied loose in box:
Toy wheel x 4 x 6Friction blocks
IMPORTANT! Please note that a screwdriver (not included) is required to access the Toy Tray Battery Pack to insert 2 x AA Batteries
(sold separately).
To assemble Toy Wheels...
To assemble Front Castors...
1
1
2
Lift Main Frame until the unit clicks into position
and is able to stand freely without assistance.
Flip the unit over to access the base.
Push all four toy wheels into position until they
“click”and lock into position.
1a.
1a.
2a.

ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Front Castors continued...
To assemble Rear Wheels...
To assemble Friction Blocks...
To assemble rear Seat Support...
2
1
1
1
Push the castors into the position (the hole
closest to the edge of the front of the walker),
until it is fully locked as shown in the image
opposite.
Insert the Rear Wheels into the frame by
aligning the slot and pressing in until it is fully
locked as shown in the image opposite.
Insert the Friction Blocks around the base into
the corresponding mountings.
Push into place until fully locked as shown in
the image opposite.
Flip the unit over to access the Main Frame.
Push rear Seat Support into slots located on
the Rear Upper Tray until it“clicks” and locks
into position.
2a.
1a.
1a.
1b.
1a.

ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Seat Pad...
1
2
3
Place the Seat Pad over the rear Seat Support
with the warning label facing the rear.
Push the plastic tabs through the openings in
the Main Frame provided.
From the underside, pull the tabs down and
clip onto the frame.
Unit should now resemble the image opposite.
1a.
1b.
2a.
3a.
To assemble rear Seat Support continued...
2Unit should now resemble the image opposite.2a.

ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Side Mirrors...
To assemble Rear Spoiler...
To assemble Toy Tray...
1
1
1
2
Push the Side Mirrors into the top frame.
Unit should now resemble the image opposite.
Push the Rear Spoiler into slots located on the
Rear Upper Tray until it“clicks” and locks into
position.
Unit should now resemble the image opposite.
Turn Toy Tray over and unscrew the battery
cover.
Insert 2 x AA batteries.
Replace battery cover by screwing back into
place.
Position the rear side of the Toy Tray into the
Main Frame.
Push the front side of the Toy Tray down to click
into position.
1a.
1b.
1a.
1b.
1a.
1b.
1c.
2a.
2b.
The walker is now ready for use.
IMPORTANT! Please note that a screwdriver (not included) is required
to access the Toy Bar Battery Pack to insert 2 x AA Batteries (sold
separately).

ASSEMBLY / OPERATING INSTRUCTIONS
To adjust Unit Height...
1
2
3
4
To adjust the height of the unit,ip the unit over.
Grasp the base to prevent it from collapsing.
Twist red knob clockwise.
Push red knob in while sliding unit to desired
height.
Release red knob and it will automatically lock into
position.
There are 3 height positions for this walker and
one fold position.
1a.
1b.
2a.
2b.
3a.
4a.

HOW TO CARE FOR YOUR CHILDCARE WALKER
Cleaning
Maintenance
This product has been designed and developed with safety,comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference.
To ensure the long-lasting use of your walker, do not use abrasive
cleaners.Always store product in a clean dry place.
Seat Pad: Remove from frame. Fasten buckles on seat restraint and
seat pad. Hand wash with cold water. No bleach.
Music Tray and snack tray: Wipe clean with a damp cloth and mild
soap.Air dry. Do not immerse in water.
Frame: Wipe the metal frame with soft, clean cloth and mild soap.
Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required. To maintain the safety of
your walker, seek prompt repairs for bent, torn, worn or broken parts.
Use only those parts and accessories approved by CNP Brands.
If you have any difculties in assembling the walker, please contact
our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand
contact Wainhouse Distribution on 0800 567 5000.

Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut,VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [e-mail]