Childcare BabyDen User manual

CNP BRANDS
20 Calarco Drive
Derrimut, Victoria. 3030, Australia
Tel: [phone]
email: [email protected]
www.cnpbrands.com.au
Bl. 012-3001-1084a-C

User Guid e
The BabyDen
The ConfigureGate
The HearthGate

Index
 • Warnings 4
 • Careofyourproduct 4
 • Partschecklist 5
 • Overviewofbasicgates 18
 • UnfoldingandsettinguptheBabyDen 6-7
 • Accessories(availableseparately) 7
 • Fittingthebase 8
 • Openingandclosingthewalkthroughdoorsection 9
 • Measuringtheareaaroundthefireplace/hearth 10
 • UnfoldingandsettinguptheHearthGate 12
 • Fittingthewallfitting 13-15
 • Openingandclosingthewalkthroughdoorsection 9
 • Measuringtheareatoprotectorisolate 11
 • UnfoldingandsettinguptheConfigureGate 12
 • Fittingthewallfittings 13-15
 • Openingandclosingthewalkthroughdoorsection 9
 • Addingoptionalsections 16
 • Removingsections 17
 • Fittinghingecaps/cones/covers 17
Generel
information
The BabyDen
The HearthGate
The Configure-
Gate
Extra
functions
3

4
Important Notes
PleasenotethatthisUserGuideappliestoall
threeproducts.Consequently,equipmentand
illustrationsmaynotcorrespondtoyourpro-
duct.
Pleasemakesurethatyourproductisnot
damaged.Yoursuppliermustbeadvisedabout
transportdamages,ifany,beforeyoustart
usingtheproduct.
Whenfittedasinstructed,thisproductcomplies
thefollowingstandards:
ASTMF1004
IMPORTANT. KEEP
INSTRUCTIONS
FOR FUTURE
REFERENCE
BeforeattemptingtounfoldtheBabyDen
/HearthGate/ConfigureGate,readtheinstruc-
tionsthoroughly.Failuretodosomayresultin
damagetothegateandrisktoyourchild.
• Intendedforusewithchildrenfrom0months
through24months.
• Whenusedasasafetygate(HearthGate 
/ConfigureGate),neverusewithoutwall
fittings.
• WhenusedasaHearthGate,alwaysplace
thegatemimimum75cm(29.5”)away 
fromthesourceofheat/fireandminimum 
90cm(35.4”)fromopenfire.
• Sinceeveryfireplace/woodburningstove 
reachesdifferenttemperatures,theabove 
placingisonlyintendedasaguideline. 
Testyourownunitatmaximumheatoutput
beforeplacingthegate.Ifthegateishotto
touch,movegatefurtherfromheatsource
thantherecommendedminimumdistance.
• Checkandtightenmountingsregularly
• Neverallowchildtoclimborswingongate.
• Donotuseifanypartofgateisbrokenor 
missing.
• Whenfolded,storeawayfromchildren.
• Thisproductwillnotnecessarilypreventall
accidents.
Never leave child unattended.
• UseonlyapprovedsparepartsfromBabyDan.
• Useonlywithlockingmechanismsecurely
engaged.
• Installaccordingtomanufacturer’s
instructions.
• Whenusedasafiresurround,thisproduct
isnotafireguard.Itisintendedtokeep 
childrenawayfromtheareasurrounding 
thefireplace.
• DonotleaveanythingintheBabyDen 
whichcouldprovideafootholdorcreatea
dangerofsuffocationorstrangulation.
• WhenusedasaBabyDenbeawareofthe
riskofopenfireandothersourcesofstrong
heat,suchaselectricbarfires,gasfires,etc.
inthenearvicinityoftheBabyDen.
WARNING:
Topreventseriousinjuryordeath,
securelyinstallgateorenclosure
anduseaccordingtomanufacturer’s
instructions.Neverleavechildunat-
tended.Neverusewithachildableto
climboverordislodge/openthegateor
enclosure.Thisproductwillnotneces-
sarilypreventallaccidents.Useonly
withlocking/latchingmechanismsecu-
relyengaged.
Warnings
Care of Your Product
• NopartoftheBabyDen/HearthGate  
/ConfigureGaterequireslubrication.
• Cleansectionsandplasticpartsusing 
warmsoapywater,oradampcloth.
• Donotuseabrasivecleanersorbleach
• Textilebasewashableatmax.40˚C.
• Assurpluscolourmightoccurplease 
washbeforeuse.
• TextilebaseMUSTNEVERBEPUTINTHE
TUMBLEDRYER!
• Ifusingoutdoors,andtohelpprevent 
rust,treatallexposedmetalonthegate 
witharustinhibitor.Somerustingmaystill
occur.
!

Parts Check List
HearthGate ConfigureGate Baby Den
incl. wall incl. wall
Qty. Description fittings fittings
1 60cm(24”)Extension
 Availableseparately 
1 ConfigureGate
 consistingof3sections 
1 HearthGate
 consistingof5sections
1 BabyDen
 consistingof6sections  
2
UpperBarBrackets(A)
2 LowerBarBrackets (B)   ()
2 LowerBarSlides (C)   ()
4
WallPlates (D)   ()
2 LowerBarBracketsscrews (E)   ()
2 UpperBarBracketsnuts (F)   ()
2
Hingecaps withgroove(G)   ()
2
Hingecovers plain(H)   ()
2
Hingecones (I)   ()
2
Removable,verticalbar (J)   ()
8 Woodscrews (K)   ()
5

6
Unfolding and Setting up the BabyDen
UnpackyourfoldedBabyDenonastable
surfacemakingsurethehandleisonthetop
side.
SeparatetheBabyDenintotwopartsby
liftinguponthecentreremovable,vertical
bar(seeill.1)whileslidingitsidewaysoutof
thelowerhinge(1a).
Unfoldthesections:
Liftup(1)onthesectionwithtophinges
whilepressingdown(2)ontheconnected
section(2).
Itiseasiesttoliftupandturnthesectionsif
youliftandpressasclosetothehingesas
possible(seeill.2).
Turnaroundthesection(3).
Thetophingeshavemarkingsintendedfor
settingupasaBabyDen.
InordertosetuptheBabyDeninasquare
orahexagon,turnaroundthesections,and
releasewhenthearrowonthehingeisinline
withthemarkingonthetophinge.
Foldoutbothpartssothatthesectionsform
ahexagon-followthemarkings:
1.
2.
3.
4.
1a
Central
vertical bar
Top hinge
Pressdown
Liftup
Cone hinge
2a
(1)(2)
(3)

Unfolding and Setting up the BabyDen
Theremovable,verticalbarhasbeenfitted
intheendsectionbythemanufacturer(see
”overviewofbasicgates”page18).
Liftuptheverticalbarandremoveit.
Aligntheendsofthetwopartsandmake
surethatthehingesdroptogetherbothon
topandbottom(seetheextractspicturesof
ill.5).
Connectthetwopartsbypushingtheverti-
calbars(1)upintothetophingeandlet
themslideintothegrooveofthelowerhinge
(2).
Wallmountingequipmentisnotincluded
withtheBabyDen.
ShouldyouwishtousetheBabyDenasa
safetygate,followtheinstructionsofthe
ConfigureGateandHearthGate(seeindex
page3).
Note:
Shouldyouwanttoattachall6sectionsof
theBabyDentothewall,youwillhavetouse
theenclosedlooseverticalbar(J).
5.
6.
7.
Re-fitthevertical
bar
Tophinge
Bottomhinge
6a (1)
(2)
7

8
Fitting the Base (Base only included in CC7050C)
PlacethetextilebaseintheBabyDenwith
theprintedsidefacingup.
Startbyfittingthebasetothethreecorners
withhingesasshowninill.9.
Passtheelasticofthebaseunderneaththe
BabyDen.
Slidetheremovable,verticalbaroutofthe
hinge.Holdtheelasticasshown(seeill.10),
whileslidingthebarbackinplace.
Hereafterfitthelastthreecornersofthe
basebypullingtheelasticunderneaththe
BabyDenanduparoundthehinge(seeill.
11).
Tietheribbonsaroundthehorizontal,square
tubesofthemetalsections-notaroundthe
bars.
8.
9.
10.
11.

Opening and Closing the Walk Through Door Section
Opening of walk through door section
Squeezethehandleasfaraspossible(1).
Thedoormayeasilybeopenedineitherdirec-
tion(2).
Closing the walk through door section
Squeezethehandleasfaraspossible(1)and
alignthebottomofdoorwithgateframe.
Releasehandle,anddoorshouldlock.
Thewalkthroughdoorsectionwillbepro-
perlylockedwhenthehandlehookfalls
downintotheholeoftheoppositehinge(see
pos.A),andthelockingbarandtheholeof
thebottomframehaveengaged(seepos.B
ofill.15).
Testtoensurebothlocksareengaged.
12.
13.
14.
15.
Pos.A
(1)
Pos.B
(1)
(2)
(2)
9

10
Measuring the Area Around the Fireplace/Hearth
Measuring around fireplace/hearth.
The distance from the gate sections to the
fireplace/hearth must be minimum 75 cm
(29.5”).
• Thegatemustneverbesetupina  
straightline.
Shoulditnotbepossibletokeeptherecom-
mended distances, separate sections are
availableatyoursupplier.
The distance from the gate sections to
open fire must be minimum 90 cm (35.4”).
• Thegatemustneverbesetupina  
straightline.
16.
17.
Important
• Thementionedminimumdistancesto 
 fireplace/hearthareonlyrecommended 
 distancessinceeveryfireplace/wood 
 burningstovereachesdifferenttempera-
 tures.Testyourunitatmaximumheat 
 outputbeforefinalplacingofthegate.
• Placethegateaccordingtotheinstruc-
 tionsatmaximumheatoutput.Ifgateis
 toohottotouch,movegatefurtherfrom
 heatsourcethanrecommended.
Min.75cm
(29.5”)
Extension
Extension
Extension
Min.75cm
(29.5”)
Min.75cm
(29.5”)
Min.90cm
(35.4”)
Min.90cm
(35.4”)
Min.90cm
(35.4”)

Measuring the Area to Protect/Isolate
Setting up on top of stairs
IftheConfigureGateisplacedontopof
stairs,pleasenotethefollowing:
• Thegatemustbesetupinacurveaway
 fromthestairs(seeill.18).
• Thegatemustneverbesetupina 
 straightline.
• Theremustbeaminimumdistanceof40
 cm(15.7”)fromgatetostairs.
Shoulditnotbepossibletokeeptherecom-
mended distances, separate sections are
availableatyoursupplier.
Setting up on bottom of stairs
IftheConfigureGateisplacedonbottomof
stairs,pleasenotethefollowing:
• Thegatemustbesetupinabowaway 
 fromthestairs(seeill.19).
• Thegatemustbeplacedasfarawayfrom
thestairsthatthechildwillnotbeableto 
reachthebottomstairandcrawloverthe 
gate.Thedistancetothebottomstair  
mustbeminimum40cm(15.7”).
In general
Pleasenotethatthechildisabletoreach
throughthebars-thereforeplacethegate
farawayfromthings.
• Thegatemustneverbesetupina  
straightline.
Please note the following:
With3sectionsitfitsopningsfrom90-180cm.
With5sectionsitfitsopningsfrom90-300cm.
With6sectionsitfitsopningsfrom90-360cm.
18.
19.
20.
Extension
Extension
Extension
Min.40cm
(15.7”)
11

12
Setting up the HearthGate and ConfigureGate
Placethefoldedgateonastablesurface
withthehandlefacingup.
SeparatetheHearthGateintwopartsbypul-
lingupinthecentreremovable,verticalbar
(seeill.21)andletitslideoutofthegroove
ofthebottomhinge(ill.21a).
Unfoldthesections:
Atthecorner,liftupslightlyonthesection
withhingeteethfacingdown(1)whilegently
pressingdownontheconnectedsection(2).
Rotatethesection(3).
Unfoldthegatetothedesiredshape.
Unfoldbothpartsandaligntheendsection
withconehingeunderneaththeendsection
withtophinge(ill.23)-besurethatthe
hingesengagebothontopandonbottom
(seecircledrawingsofill23).
Connectthetwopartsbypushingtheremo-
vable,verticalbarupintotheupperhinge(1)
andletitslideintothegroove(2).
• Ifaddingsections-gotopage16.
• Ifgateistoolong-gotopage17.
• Ifmakingnochanges-continuewith 
 fittingthewallfittingsonnextpage.
21.
22.
23.
24.
Fitverticalbar
21a
Centre vertical
bar
Pressdown
Liftup
Cone hinge
Tophinge
Bottomhinge
24a
22a
Top hinge
(2)
(1)
(1)
(2) (3)

max
15cm
(6”)
ad
d
b
c
25a.
Fitting the Wall Fittings
Assemblelowerbarbrackets(b)andslides
(c)withscrewsandnutsasshown.Tighten
screwsjustenoughtoallowpartstoslide
easily.Slidewallplates(d)ontobackof
upperandlowerbarbrackets(aandb)until
clickisheardandlockedinplace.
Placeupperbracketaroundtopconehinge.
Slidelowerbracketassemblyonto
removablebarandpushbarupintoupper
bracket.Repeatforoppositesideofgate.
MoveConfigureGatetodesiredlocation.
Rotateupperandlowerbracketsuntilflush
againstmountingsurface.Withapencil,out-
linebracketsonmountingsurface.
NOTE: Lowerbracketisadjustable.Itcanbe
movedup(maximum15cm(6”))toaccom-
modatevariousheightsoffloormolding;and
bylooseningscrew,canadjustwidthsto
accommodate uneven wall construction.
25.
26.
27.
28.
13

Screwholes
Press
Press
16a.
14
Fitting the Wall Fittings
Removewallplatesfrombracketsbypres-
singlockingtabs(29and30)andliftingoff.
WARNING
Ifplacedaroundafireplace/hearth,adistan-
ceofminimum75cm(29.5”)fromsourceof
heat/fireisrecommended.
Ifplacedaroundopenfire,minimumdistance
mustbe90cm(35.4”).
Seealso”Measuringtheareaaroundthefire-
place/hearth”onpage10.
Holdonewallplate(d)insidewalloutlineand
screwintwowoodscrews.Repeatforother
wall plate.
NOTE:Screwsprovidedareformounting
directlyintowood.Ifmountingintobrick,
drywallorothersurfaces,useappropriate
hardware.
29.
30.
31.
32.
Min.75cm
(29.5”)

Fitting the Wall Fittings
Reattachbracketstowallplates.Gateshould
nowbeproperlyinstalled.
Theotherendofthegateisfittedinthe
sameway.
OpeningandclosingtheWalkThroughDoor
Section:Seepage9
33.
15

16
Adding Optional Sections
Anextensionhasatophingeinoneendand
aconehingeintheother.Thismakesitpos-
sibletofittheextensiontoallkindsof
sections.
Theremovable,verticalbarhasalreadybeen
fittedbythemanufacturer.Removethisbar
byliftingitup(1)andslidingitoutofthe
lowerhinge(2).
Toavoidrearrangingthecaps/covers/cones,
addextensionsaccordingtothenextillustra-
tions.
ConfigureGate
Separatethegatebetweendoorandsection
(seeill.35)byremovingtheremovable,verti-
cal bar.
Fittheextensionbyplacingthetophingeon
thedoorsectionovertheconehingeofthe
extension(seeill.35a).Thehingesmustbe
alignedbothontopandbottom.
Letthehingesdroptogetherandinsertthe
removable, vertical bar.
Fitthelastsectioninthesameway.
HearthGate
Separatethegatebetweentwosections(see
ill.36)byremovingtheremovable,vertical
bar.
Fittheextensionbyplacingthetophingeof
theextensionovertheconehingeofthesec-
tion(seeill.36a).Thehingesmustbealigned
bothontopandbottom.
Letthehingesdroptogetherandinsertthe
removable vertical bar.
Fitthelastsectioninthesameway.
34.
35.
36.
1
2
ConeHinge
Tophinge
35a
36a
Tophinge
Extension
Tophinge
Extension
Conehinge Conehinge

Removing Sections
Ifyouwanttoremoveasectionfromthe
gateyouhavebought,alwaysremovethe
endsection(s).
Removetheremovable,verticalbarbylifting
itup(1)andletthebarslideoutofthe
groovetowardsthehinge(2).
Liftoffthesection(s).
Removetheloosecapsfromtheendsection
(theillustrationshowstheendsectionofthe
HearthGate-endsectionofConfigureGate
seeill.40).
Fitting of hinge caps /cones /covers
Dependingonthenumberofsectionsremo-
vedoradded,youwillendupwithoneofthe
illustratedendsections(ill.39and40).
Fittheloosecaps/covers(remainingcaps
/coversareenclosedinaplasticbag)on
whatisnowtheendsectionsaccordingtoill.
39and40.
Thecaps/coversareenclosedinaplastic
bag.Fittheseaccordingtoill.39and40.
37.
38.
40.39.
H
I
G
H
37a
Loosecap
Loosecap
(2)
17

6
2 21
13 2 31 2
13 2 31 2 2
6
44
4
5
4
5
7
4
7
7
4x
6x
6x
Overview of Basic Gates
ConfigureGate
HearthGate
BabyDen
1a
1b
18
AssemblingtheBabyDen
Walkthroughdoor
Sectionwithwalkthroughdoor
Handle
Lockingbar
Sectionwithconehinges
Sectionwithtophinges
Loosecap,plain
Loosecapwithgroove
Loosecap,cone
Removable,verticalbar
(thesearesetoffingrey)
1
1a
1b
2
3
4
5
6
7