Christie DWX555-GS User manual

USER MANUAL
020-000724-02
GS Series
DWX555-GS/DHD555-GS/DWU555-GS

The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.

NOTICES
COPYRIGHT AND TRADEMARKS
Copyright ©2015 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their
respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user's own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user's
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES DANS
LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT DES
INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
! ! ! ! ! ! ! ! !
! ! -! ! ! ! ! ! ! /

GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or
availability could occur which may not be reflected in this document. Christie reserves the right to
make changes to specifications at any time without notice. Performance specifications are typical,
but may vary depending on conditions beyond Christie's control such as maintenance of the
product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be
liable for errors contained herein or for incidental or consequential damages in connection with the
performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can be
recycled and reused. This symbol means that electrical and electronic equipment, at their end-
of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie's limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie's limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Problems caused by combination of the product with non-Christie equipment, such as
distribution systems, cameras, video tape recorders, etc., or use of the product with any non-
Christie interface device.
c. Damage caused by misuse, improper power source, accident, fire, flood, lightening,
earthquake or other natural disaster.
d. Damage caused by improper installation/alignment, or by product modification, if by other than
a Christie authorized repair service provider.
e. For LCD projectors, the warranty period specified applies only where the LCD projector is in
"normal use". "Normal use" means the LCD projector is not used more than 8 hours a day, 5
days a week. For any LCD projector where "normal use" is exceeded, warranty coverage under
this warranty terminates after 6000 hours of operation.
f. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.

Table of Contents
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) i
1. SAFETY
2. INTRODUCTION
2.1 Projector Components.................................................................................................. 2-1
2.2 Built-in Keypad..............................................................................................................2-4
2.3 Input/Output (I/O) Panel................................................................................................ 2-5
2.4 Remote Control............................................................................................................. 2-6
2.5 LED Status Indicators................................................................................................... 2-8
3. INSTALLATION
3.1 Connect to Computer.................................................................................................... 3-1
3.2 Connect to Video Equipment........................................................................................ 3-2
3.3 Turn the Projector On................................................................................................... 3-3
3.4 Turn the Projector Off................................................................................................... 3-3
3.5 Adjust the Projector Position......................................................................................... 3-4
3.6 Calculate Lens Offset ................................................................................................... 3-7
3.7 Removing and Installing the Lens............................................................................... 3-13
3.8 Cable Cover Installation.............................................................................................. 3-14
3.9 Portrait Cover Installation ........................................................................................... 3-15
3.10 Ceiling Mount Installation............................................................................................ 3-16
4. OPERATION
4.1 Size and Position Menu................................................................................................ 4-2
4.2 Image Settings Menu.................................................................................................... 4-7
4.3 Configuration Menu ...................................................................................................... 4-9
4.4 Light Source................................................................................................................4-14
4.5 Status Menu................................................................................................................ 4-15
4.6 Input Switching & PIP Menu....................................................................................... 4-18
4.7 Language Menu.......................................................................................................... 4-20
4.8 Test Pattern Menu ...................................................................................................... 4-20
4.9 Web User Interface..................................................................................................... 4-21
4.9.1 Logging On .................................................................................................... 4-21
4.9.2 Main Tabbed Page - General......................................................................... 4-21
4.9.3 Main Tabbed Page - Status ........................................................................... 4-22
4.9.4 Main Tabbed Page - Lens.............................................................................. 4-23
4.9.5 Network.......................................................................................................... 4-24
4.9.6 Tools .............................................................................................................. 4-27
4.9.7 Administrator Page ........................................................................................ 4-27
4.9.8 About Page .................................................................................................... 4-28
4.10 Christie Presenter....................................................................................................... 4-29
4.10.1 Connect to the Projector ................................................................................ 4-29
4.10.2 Install Christie Presenter software ................................................................. 4-30
4.10.3 Use Christie Presenter................................................................................... 4-31
4.11 Card Reader Operation .............................................................................................. 4-37
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1 Inputs............................................................................................................................ 6-1
6.2 PIP/PBP Compatibility .................................................................................................. 6-6

Table of Contents
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) ii
6.3 Key Features ................................................................................................................6-7
6.4 List of Components....................................................................................................... 6-8
6.5 Optional Accessories.................................................................................................... 6-8
6.6 REGULATORY............................................................................................................. 6-9
6.7 Federal Communications Commission (FCC) Warning.............................................. 6-10
6.8 OSD Tree.................................................................................................................... 6-11
6.9 Preset Mode tables..................................................................................................... 6-19

Section 1: SAFETY
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 1-1
1. SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
WARNING
.
• Do not look into the projector lens when the laser is on. The bright light may
result in permanent eye damage.
• To reduce the risk of fire or electric shock, do not expose this projector to
rain or moisture.
• Do not open or disassemble the projector as this may cause electric shock.
• All installation and maintenance procedures must be performed by a
Christie accredited service technician.
• Keep all combustible material away from the concentrated light beam of the
projector.
• Position all cables where they cannot contact hot surfaces or be pulled or
tripped over.
• Always power down the projector and disconnect all power sources before
servicing or cleaning.
• Use a soft cloth moistened with a mild detergent to clean the display
housing.
• Disconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
• Operate the projector under the following conditions:
- Operating temperature range: 5°C to 35°C
- Storage temperature range: -10°C to 60°C
- Humidity range: 5% to 80 % RH (Max.), non condensing
- Operating altitude: 10,000 ft. maximum
• Use only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specified voltage and power range for
your region.
• Remove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
• Do not block the ventilation slots and openings on the projector.
• Do not use abrasive cleaners, waxes or solvents to clean the projector.
• Do not allow anything to rest on the power cord.

Section 1: SAFETY
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 1-2
Important Laser Notice
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007.
IEC 60825-1:2007
WARNING
.
• This projector is a Class 2 laser device that conforms with IEC 60825-
1:2007 and CFR 1040.10 and 1040.11
• Class 2 laser product, Do Not Stare Into Beam
• This projector has built-in Class 4 laser module. Disassembly or
modification is very dangerous and should never be attempted.
• Any operation or adjustment not specifically instructed by the user's guide
creates the risk of hazardous laser radiation exposure.
• Do not open or disassemble the projector as this may cause damage by the
exposure of laser radiation.
• Do not stare into beam when the projector is on. The bright light may result
in permanent eye damage.
• Without following the control, adjustment or operation procedure may
cause damage by the exposure of laser radiation.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
MAX OUTPUT:8.0mW
WAVE LENGTH:440~455nm

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-1
2. INTRODUCTION
The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip laser based projector. The projector is available in
WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light
Processing (DLP®) technology from Texas Instruments. It is primarily designed
for fixed installation markets.
2.1 Projector Components
Front View
Ind. Part Name Description
1Front IR Sensor Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
2 Projection Lens Allows automated lens control and adjustment:
vertical and horizontal offsets, zoom and focus.
3Lens Ring Protects the lens motors and mechanism. Remove in
order to insert or remove the lens.
4 Adjustable Feet Raise or lower the feet to level the projector.
1
2
3
4

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-2
Rear View
Ind. Part Name Description
1Rear IR Sensor Receives signals from the IR remote. Keep the signal
path unobstructed for uninterrupted communication
with the projector.
2 Input/Output (I/O) Panel Connects the projector to external devices.
3AC Input Connect to the supplied power adapter.
4 Power Button Switch the power button to turn on the power source.
5Kensington Lock Use to secure the projector to countertops, tables, etc.
K
HDBaseT REMOTE
IN
GREEN/Y BLUE/PB RED/PR RS232 USB
MINI USB
ETHERNET CVBS S-VIDEO
REMOTE
OUT HDMI VGA IN VGA OUT DISPLAY PORT DVI
1
2
3
4
5

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-3
Left View
Right View
Ind. Part Name Description
1Cooling Air Vents
(Intake) Keep these vents unobstructed to prevent the projector from overheating.
2 LED Status Indicators Displays the status of the projector. They are (from left
to right): LIGHT, STATUS, and PIC MUTE.
3Built-in Keypad Controls the projector.
4Cooling Air Vents
(Exhaust) Keep these vents unobstructed to prevent the projector from overheating.
1
2
3
4

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-4
2.2 Built-in Keypad
Ind. Part Name Description
1Power Turn the projector on or off
2 Menu Display menus
3Enter Confirm a selection
4 Auto Automatically optimize image
5Lens Adjust the lens vertical or horizontal offset setting
6 Focus Adjust focus
7Exit Return to previous level or exit menus if at top level
8 Arrow Keys • Adjust a setting UP or DOWN
• Navigate within a menu
9Input Select an input for the main or PIP/PBP image
10 Picture Mute Display or blank the video image.
11 Zoom Adjust zoom
7
9
8
10
11
1
2
3
5
6
4

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-5
2.3 Input/Output (I/O) Panel
Ind. Connector Name Ind. Connector Name
1HDBaseT 9Component IN
2 Remote IN 10 RS232
3Remote OUT 11 Mini USB
4 HDMI 12 USB Type A
5VGA-IN 13 Ethernet
6VGAOUT 14CVBS
7Display Port 15 S-Video
8DVI
HDBaseT REMOTE
IN
GREEN/Y BLUE/PB RED/PR RS232 USB
MINI USB
ETHERNET CVBS S-VIDEO
REMOTE
OUT HDMI VGA IN VGA OUT DISPLAY PORT DVI
1
9
2 3 4 5 6 7 8
10 12 13 14 1511

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-6
2.4 Remote Control
16
17
18
19
20
21
22
24
25
26
27
28
29
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
23

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-7
Ind. Part Name Description
1Picture Mute Display or blank the video image.
2 Power on Turn projector ON.
3Gamma Adjust mid-range levels.
4 Bright Adjust amount of light in the image.
5PIP/PBP Turn PIP/PBP ON/OFF.
6 Size Adjust the PIP/PBP size
7Number Keys Enter a number, such as a channel, value, etc.
8 Help Display context-sensitive help.
9Menu Display menus.
10 Arrow Keys • Adjust a setting UP or DOWN.
• Navigate within a menu.
11 Test Display a test pattern.
12 Auto Automatically optimize image.
13 OSD Use to hide or show menus.
14 Keystone H Adjust the horizontal keystone.
15 Keystone V Adjust the vertical keystone.
16 Standby Turn projector OFF.
17 Contrast Adjust difference between dark and light.
18 Hot-key Select your preset keys quickly.
19 Swap Swap the main and PIP/PBP images.
20 Layout Adjust the PIP/PBP layout.
21 Focus Adjust focus to improve image clarity as desired.
22 Zoom Adjust zoom to achieve a desired image size.
23 Proj Key Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
24 Exit Return to previous level or exit menus if at top level.
25 Enter • Select a highlighted menu item.
• Change or accept a value.
26 Input Select an input for the main or PIP/PBP image.
27 Info Display source image information.
28 Lens H Horizontal Lens Shift - Adjust the position of the image
horizontally.
29 Lens V Vertical Lens Shift - Adjust the position of the image
vertically.

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-8
2.5 LED Status Indicators
The LED status indicators are located on the right side of the projector. Each
LED is defined below.
• LIGHT LED
• STATUS LED
LED Status Projector State
Red (flashing) When projector has lost over 60% initial luminance
Orange (solid) Laser diode time has expired
Green (solid) Laser diode is on and operating correctly
Off Laser diode is off
LED Status Projector State
Off AC power is off (without AC plug in)
Off, but keypad LED
is on AC has been applied, projector is in standby mode
Green (solid) Projector is powered up and operating normally
Green (flashing) Projector communications
Orange (solid) Non-portrait mode used
NOTE: Please refer to section 3.5.
Orange (flashing) Projector is in cool down mode or startup mode
Green (flashing) /
Red (flashing) Projector is in flash (LAN) update state
Red (solid) Over-temperature
Red (flashing) Fan failure

Section 2: INTRODUCTION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 2-9
• PICTURE MUTE LED
LED Status Projector State
Green (solid) Light is on - image is displayed
Orange (solid) Light is on - image is blank

Section 3: INSTALLATION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 3-1
3. INSTALLATION
3.1 Connect to Computer
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1RS232 Cable 4USB Type B Mini Cable 7DisplayPort Cable
2 HDMI Cable 5 VGA out Cable 8 DVI Cable
3VGA in Cable 6USB Type A Cable 9Power Cord
HDBaseT REMOTE
IN
GREEN/Y BLUE/PB RED/PR RS232 USB
MINI USB
ETHERNET CVBS S-VIDEO
REMOTE
OUT HDMI VGA IN VGA OUT DISPLAY PORT DVI
Desktop Laptop
1 2 3 4 5 6 7 8
9

Section 3: INSTALLATION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 3-2
3.2 Connect to Video Equipment
NOTE:
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
Ind. Connector Name Ind. Connector Name Ind. Connector Name
1Component
(YPbPr) Cable 4VGA in Cable 7CVBS Cable
2HDMI Cable 5 3 RCA Component
Cable 8 S-Video Cable
3VGA to RBG
SCART 615-pin to 3 RCA
Component/HDTV
Adapter
HDBaseT REMOTE
IN
GREEN/Y BLUE/PB RED/PR RS232 USB
MINI USB
ETHERNET CVBS S-VIDEO
REMOTE
OUT HDMI VGA IN VGA OUT DISPLAY PORT DVI
Component video output equipment DVD player
1 2
3
4
5
6
7 8
Video cassette recorder

Section 3: INSTALLATION
GS Series User Manual
020-000724-02 Rev. 1 (10-2015) 3-3
3.3 Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated.
2. Turn on the projector by pressing " " on the remote control or press " "
on the built-in keypad. The Status LED is Orange with a long blink.
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite
Video).
4. The projector detects the source you selected and displays the image.
NOTE:
The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is
displayed.
3.4 Turn the Projector Off
1. Press " " on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
2. Press " " again to confirm your selection. If you do not press " " again,
the warning message will disappear after 10 seconds.
1
1
2
1
3
Status LED
1
2
1
Power on
1
2
Input Key
1
3
Power on
1
2