manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Christie
  6. •
  7. Projector
  8. •
  9. Christie I Series User manual

Christie I Series User manual

This manual suits for next models

16

Other Christie Projector manuals

Christie Roadster S9 User manual

Christie

Christie Roadster S9 User manual

Christie HS Series Operating manual

Christie

Christie HS Series Operating manual

Christie boxer 4K30 User manual

Christie

Christie boxer 4K30 User manual

Christie LWU701i User manual

Christie

Christie LWU701i User manual

Christie Q Series User manual

Christie

Christie Q Series User manual

Christie D4K25 User manual

Christie

Christie D4K25 User manual

Christie DWU951 User manual

Christie

Christie DWU951 User manual

Christie CP4230 User manual

Christie

Christie CP4230 User manual

Christie RPMX-D120U User manual

Christie

Christie RPMX-D120U User manual

Christie CP2309-RGB Assembly instructions

Christie

Christie CP2309-RGB Assembly instructions

Christie CP2320-RGB Assembly instructions

Christie

Christie CP2320-RGB Assembly instructions

Christie DWU951 User manual

Christie

Christie DWU951 User manual

Christie Mirage 304K Assembly instructions

Christie

Christie Mirage 304K Assembly instructions

Christie CP2215 User manual

Christie

Christie CP2215 User manual

Christie DWU951 User manual

Christie

Christie DWU951 User manual

Christie LX900 User manual

Christie

Christie LX900 User manual

Christie D4KLH60 Mirage 4KLH User manual

Christie

Christie D4KLH60 Mirage 4KLH User manual

Christie Vivid Red Guide

Christie

Christie Vivid Red Guide

Christie Q Series User manual

Christie

Christie Q Series User manual

Christie D4K3560 User manual

Christie

Christie D4K3560 User manual

Christie J Series 2.0 kW User manual

Christie

Christie J Series 2.0 kW User manual

Christie CP2315-RGB Assembly instructions

Christie

Christie CP2315-RGB Assembly instructions

Christie CP2208-LP User guide

Christie

Christie CP2208-LP User guide

Christie CP2000-M User manual

Christie

Christie CP2000-M User manual

Popular Projector manuals by other brands

iEmmet MP-312 user manual

iEmmet

iEmmet MP-312 user manual

Epson VS400 Specifications

Epson

Epson VS400 Specifications

Sony VPL-HS10 Marketing Specifications & Features manual

Sony

Sony VPL-HS10 Marketing Specifications & Features manual

Sony VPL-HW65ES Quick reference manual

Sony

Sony VPL-HW65ES Quick reference manual

Toshiba TLP-791U Specifications

Toshiba

Toshiba TLP-791U Specifications

Philips LC1341 Declaration of conformity

Philips

Philips LC1341 Declaration of conformity

NEC NP600S EDU Specifications

NEC

NEC NP600S EDU Specifications

BenQ SH753P user manual

BenQ

BenQ SH753P user manual

Eiki EK-623U series quick start guide

Eiki

Eiki EK-623U series quick start guide

Epson PowerLite Pro Cinema 6020UB user guide

Epson

Epson PowerLite Pro Cinema 6020UB user guide

Epson PowerLite Home Cinema 705HD user guide

Epson

Epson PowerLite Home Cinema 705HD user guide

Navitar FX instruction manual

Navitar

Navitar FX instruction manual

InFocus LitePro 560 user guide

InFocus

InFocus LitePro 560 user guide

Sony SRX-R815P operating instructions

Sony

Sony SRX-R815P operating instructions

Vivitar DP1500 X specification

Vivitar

Vivitar DP1500 X specification

Asus ZenBeam Latte user manual

Asus

Asus ZenBeam Latte user manual

Epson PowerLite 810p specification

Epson

Epson PowerLite 810p specification

BOXLIGHT CP-322i/CP-634i user manual

BOXLIGHT

BOXLIGHT CP-322i/CP-634i user manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

Coolant Refill Instruction Sheet 1 of 9
020-100686-01 Rev. 1 (03-2011)
Coolant Refill
Instruction Sheet
INTRODUCTION
The following procedure should be performed whenever the coolant system needs to be refilled.
NOTICE: Never allow the pump to run dry to avoid damaging it.
KITS REQUIRED
• #003-001837-xx Coolant Refill Kit (includes JeffCool E105 jug of coolant, refill bottle, funnel, MSDS sheet)
INSTRUCTIONS
SERIES I
Series 1 projectors include the CP2000-S/-SB/-h/-i/-X/-XB/-Z/-M/-MR and the Roadie 25K/HD+30K/
HD+35K. For details on how to flush the coolant system on these models refer to, Roadie 25K/
HD+30K/HD+35K, CP2000-S/-SB/-h/-i/-X/-XB/-M/-MR/-ZX Coolant Flush Instruction Sheet
(P/N: 020-100179-03).
CP2000-S/-SB/-H/-I/-X/-XB AND ROADIE 25K/D+30K/HD+35K
ACCESS COOLING SYSTEM
1. Remove the projector lid. On the Roadie 25K/HD+30K/HD+35K or CP2000-X/-XB, open the
igniter door (Figure 1, left). On a CP2000-S/-SB/-i/-h (Figure 1, right), open the non-operator
side pedestal door and skip to Step 3.
Figure 1 Access Cooling System
2 of 9 Coolant Refill Instruction Sheet
020-100686-01 Rev. 1 (03-2011)
2. On the CP2000-X/-XB or Roadie 25K/HD+30K/HD+35K, remove the center (8 screws) and front
belly pan (4 screws), as shown in Figure 2.
Figure 2 Remove Belly Pans
3. Prime/Purge of Air: Power up the projector (no lamp). Manipulate or “prime” all coolant hoses
by flicking, pinching and raising them as necessary (Figure 3) to keep liquid moving and flowing
to-and-from the pump. You must purge the system of all air, otherwise the coolant will not flow
properly and may cause the DMDs to overheat. NOTE: The coolant in the reservoir disappears
into the system immediately after the pump has been started. You must continually refill the
reservoir until the coolant level stops falling.
CAUTION! Purge all hoses of air! On CP2000-X/-XB and Roadie 25K/HD+30K/
HD+35K, check hoses in belly pan area.
Figure 3 Refill the System & Prime
all Hoses to Eliminate Air Locks
Coolant Refill Instruction Sheet 3 of 9
020-100686-01 Rev. 1 (03-2011)
4. Continue running the projector (no lamp), topping up the reservoir as you eliminate more and
more air pockets from all coolant hoses (Figure 4).
TIPS:
• Watch for air near all hose fittings.
• Tiny or large bubbles indicates air present.
Continue priming (shake hose, etc).
• Solid, opaque hoses with no bubbles indicates
system is primed and ready for use.
5. Power down. Make sure reservoir is approximately
1/2 - 3/4 full, topping up as necessary. In the
CP2000-S/-SB/-i/-h, double-check level through
the viewing gauge on the pedestal door.
6. When you are certain that all air is purged, replace
the reservoir cap, belly pan, igniter door and
projector lid.
7. Power up and test.
CP2000-M/MR
ACCESSING THE COOLING SYSTEM
1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place.
2. Turn power OFF from the Control Display Panel (CDP).
3. Remove the top lid:
a. Use a #2 Phillips™ to loosen the 7 captive screws securing the top lid to the projector housing
(Figure 5).
Figure 5 Remove Top Lid
b. Unlock the rear access door using the low security key.
c. Lift the lid up from the rear of the projector and pull it away from the 2 tabs on the front skin.
NOTE: When installing, align the front 2 tabs and reverse the above steps.
Figure 4 Check all Coolant Hoses
for Air Bubbles
4 of 9 Coolant Refill Instruction Sheet
020-100686-01 Rev. 1 (03-2011)
CP2000-S/-SB/-H/-I/-X/-XB/-M/-MR AND ROADIE 25K/D+30K/HD+35K
FILLING THE RESERVOIR
1. Loosen the top screw (Figure 6) and use the fill bottle to add coolant. Power up the projector and
continue adding coolant so the fluid level does not drop below the Minimum Fill Line.
Figure 6 Fill the Reservoir
(Reservoir for CP2210, CP2220 and CP2230 shown)
2. Air Bubble Impeding Flow: If the liquid in the reservoir does not move due to air bubbles,
remove the entire fan pack and pump section. For instructions, refer to the CP2000-M/MR
Service Manual (P/N: 020-100124-xx). Tilt the pump at different angles until the coolant starts to
flow.
Coolant Refill Instruction Sheet 5 of 9
020-100686-01 Rev. 1 (03-2011)
CP2000-ZX
ACCESSING THE COOLING SYSTEM
1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place.
2. Turn power OFF from the Touch Panel Controller (TPC).
3. Unlock the front lid using the high security key. Raise the lid and slide it out from the opposite side
(Figure 7).
Figure 7 Remove Front Top Lid
4. Remove the PCM cover by pushing on the tab at the top of the cover. Tilt the cover slightly then
lift enough to clear the tabs at the bottom and remove (Figure 8).
5. Remove the air filter cover by releasing the 2 tabs on the air filter cover, lift and remove
(Figure 8).
Figure 8 Remove PCM and Air Filter Covers
6 of 9 Coolant Refill Instruction Sheet
020-100686-01 Rev. 1 (03-2011)
6. Use a #2 Phillips™ to remove the 2 screws on the security bracket (above cardcage), which
secures the liquid cooling panel (Figure 9).
Figure 9 Remove Security Bracket
7. Remove the 4 screws securing the access panel frame, which is located on the input side of the
projector (Figure 10).
Figure 10 Remove Access Panel Frame
Coolant Refill Instruction Sheet 7 of 9
020-100686-01 Rev. 1 (03-2011)
8. Remove the 5 screws securing the liquid cooling panel. Four of these screens are on the panel and
one is located along the bottom of the panel (Figure 11). Swing the panel out and hang it on the
screws located on the frame.
Figure 11 Remove Liquid Cooling Panel
9. Fill the reservoir with coolant. NOTE: The reservoir only holds 1/2 of the required coolant for the
system.
10. Power the pump ON and watch the coolant begin
circulating. Keep adding coolant into the reservoir as
needed to prevent the fluid level from dropping below the
Minimum Fill Line. Continue running the system until the
coolant appears free from air bubbles.
Figure 12 Fill Reservoir
8 of 9 Coolant Refill Instruction Sheet
020-100686-01 Rev. 1 (03-2011)
SERIES II
Series 2 projectors include the CP2210, CP2220 and CP2230 models. For detailed information on
flushing the coolant system, refer to the CP2210, CP2220 and CP2230 Coolant Flush Instruction
Sheet (P/N: 020-100685-xx).
CP2210
ACCESSING THE COOLING SYSTEM
1. Power the projector lamp OFF. Wait for at least 10 minutes to allow for proper cooling to take
place before powering the projector OFF, via the TPC.
2. Use a #2 Phillips™to loosen the 7 captive screws securing the top lid to the projector housing
(Figure 13).
Figure 13 Remove Top Lid
3. Unlock the rear access door using the low security key. Lift the lid up from the rear of the projector
and pull it away from the 2 tabs on the front skin.
Coolant Refill Instruction Sheet 9 of 9
020-100686-01 Rev. 1 (03-2011)
CP2220 AND CP2230
ACCESSING THE COOLING SYSTEM
1. Turn the projector lamp OFF. Wait at least 10 minutes to allow for proper cooling to take place
before powering down the projector, via the TPC.
2. Unlock the front lid using the low security key provided. Lift the lid up and remove (Figure 14).
Figure 14 Remove Front Top Lid
CP2210, CP2220 AND CP2230
FILLING THE RESERVOIR
1. Loosen the top screw (Figure 15) and use the fill bottle provided to add coolant.
2. Power the projector ON and continue adding coolant until the fluid level does not drop below the
Minimum Fill Line.
3. Continue running the system until the coolant appears free from air bubbles.
Figure 15 Fill Reservoir
(Reservoir for CP2210, CP2220 and CP2230 shown)
Low Security Key