CIRCLE FITNESS E7 User manual

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 2 of 9
2
Table of Contents
1. Problem Check And Solutions
1.1. No resistance during workout ----- Page 3
1.2. Console no power, no any display ----- Page 4
1.3. Touch panel no function ----- Page 5
2. Engineering Mode
2.1. Check software version / Total used time / total used distance ----- Page 6
2.2. TV / DTV channel scan ----- Page 7
2.3. Software upgrade ----- Page 8~9

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 3 of 9
3
1. Problem Check And Solutions
1.1. No resistance during workout
Turn off the power
and wait 10 seconds
then turn it on.
Check console
wire connected
well or replace
TFT main PCB.
Press start then check
LED2 on lower control
board. Does it lights
up? (Show as Photo 1)
No
Replace lower control
board.
Yes
Photo 1

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 4 of 9
4
1.2. Console no power, no any display
Check LED1 on lower control board,
does it lights up?
Replace lower
control board.
Turn off the power
and wait 10 seconds
then turn it on.
No
Yes
Open the console
Check power lamp lights up and
power wire connection well?
No
Re-connect or replace
TFT main PCB
Yes
Does LVDS wire connect well and not breakage?
No
Re-connect or replace
wire
Yes
Replace TFT
panel
Replace TFT
main PCB
No
power

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 5 of 9
5
1.3. Touch panel no function
否
Open the console
Does lamp of Touch PCB lights up?
Does lamp of Touch PCB lights up while touch the
screen?
Touch Panel oppressed,
loosen the fix screw to
check it.
No
Yes
Check touch PCB and TFT main PCB connection
well?
Yes
No
Re-connect or replace
wire
No
Check Touch panel and
Touch PCB connection well?
No
Re-connect
or replace
Yes
Replace touch PCB
Yes
Replace TFT
main PCB

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 6 of 9
6
2. Engineering Mode
2.1. Check software version / Total used time / total used distance
Press Logo 5 seconds to
enter engineering mode.

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 7 of 9
7
2.2. TV / DTV channel scan
Press Logo 5 seconds to
enter engineering mode.
Press DTV Config to enter setting mode.
Select country then press Auto Scan.
System will be scan the DTV and ATV channel, it may
take 8~10 minutes, press Back Menu after scan
completed.

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 8 of 9
8
2.3. Software upgrade
2.3.1. Put upgrade program in the USB storage device.
※Please use USB 2.0 and flash memory under 16GB.
※Put the file (MERGE.bin) at root list in USB storage device.
2.3.2. Insert USB into USB socket.
2.3.3. Press Logo 5 seconds to enter engineering mode.
2.3.4. Press Update app 3 seconds till show Software Upgrade message then waiting for
system reboot. If screen is upside down, keep going to execute follow steps.

Document: Service Manual
Description: Elliptical/Upright Bike/ Recumbent Bike
Model: E7/B8/R8,
10.1’’ LCD
Page: 9 of 9
9
2.3.5. Press Logo 5 seconds to enter engineering mode.
2.3.6. Select model type: EPS / BS / RS or EPC / BC / RC and reboot system.
EP=Elliptical / B=Bike / R=Recumbent
S=Standard Wattage table / C=Customize Wattage table