Circutor CIRWATT Series User manual

MULTIPURPOSE
THREE PHASE METER
CIRWATT Series
C Type
Installation Manual
(M981 001-03-05C)
(c) CIRCUTOR S.A.

Page no. 1
INSTALLATION MANUAL CONTENTS Page no.
1.-
INTRODUCTION................................................................................................. 3
2.- METER MODELS ...............................................................................................3
3.- SAFETY LEVELS (Seals) ................................................................................... 3
4.- DISPLAY............................................................................................................. 4
4.1.- Dis lay Modes . ................................................................................................. 4
4.1.1.- STAND BY Mode .......................................................................................4
4.1.2.- READING Mode ......................................................................................... 4
4.2.- Ty es of screen................................................................................................. 5
4.2.1.- Stand by screen ..........................................................................................5
4.2.2.- Menu Screen...............................................................................................5
4.2.3.- Data Screen. ...............................................................................................5
4.3.- STAND BY screen mode .................................................................................. 6
4.4.- READING screens mode...................................................................................7
4.4.1.- Screen L (Main)........................................................................................... 8
4.4.2.- Screen L1(CONTRACT 1, PURCHASE) ..................................................... 8
4.4.3.- Screen L2 (CONTRACT 2, PURCHASE) .................................................. 13
4.4.4.- Screen L3 (CONTRACT 3, SALE)............................................................. 14
4.4.5.- Screen L4 (INFORMATION)...................................................................... 15
4.4.6.- Screen L40 (INFORMATION: INDICATORS) ............................................ 16
4.4.7.- Screen L5 (Info Fab) ................................................................................. 21
5.- TECHNICAL FEATURES.................................................................................. 22
6.- INSTALLATION AND START UP...................................................................... 24
6.1.- Installing the equi ment................................................................................... 24
6.2.- Indirect meter terminal ratio (see label on terminal cover)................................ 24
6.3.- Direct meter terminal ratio (see label on terminal cover) .................................. 25
6.4.- Meter connection diagrams ............................................................................. 26
7.- MAINTENANCE ................................................................................................ 27
8.- TECHNICAL SERVICE ..................................................................................... 27
A.- CIRWATT communications diagram...................................................................... 28
B.- Changing the battery............................................................................................. 28
C.- Quadrants ............................................................................................................. 29
D.- CIRWATT Ethernet communications……..……………………………………………30

Page no. 2
Index of tables
Table 1 Dis lay Codes..................................................................................................5
Table 2 Stand by screen mode .....................................................................................6
Table 3 Reading screens mode diagram ......................................................................7
Table 4 Main menus screen..........................................................................................8
Table 5 Contract 1 screen............................................................................................. 8
Table 6 Absolute energy value codes for contract 1...................................................... 9
Table 7 Incremental energy value codes for the meter................................................ 10
Table 8 Absolute energy value codes screen for contract 1 closure 1......................... 11
Table 9 Incremental energy value codes for closure 1 of contract 1............................ 12
Table 10 Absolute values screen for contract 3 closure 1 ........................................... 14
Table 11 Incremental values screen for contract 3 closure 1....................................... 15
Table 12 Screen L4. Information................................................................................. 15
Table 13 Screen L40. Indicators. ................................................................................ 16
Table 14 Screen L41. Contracted owers. .................................................................. 17
Table 15 Screen L42. Transformation ratios ............................................................... 17
Table 16 Screen L43. Information: current values....................................................... 18
Table 17 Screen L44. Instant values .......................................................................... 19
Table 18 Screen L45. Communications ...................................................................... 19
Table 19 Screen L46. Identifiers ................................................................................. 20
Table 20 Screen L47. Out ut constants...................................................................... 20
Table 21 Screen L48. Time changes .......................................................................... 21

Page no. 3
1.- INTRODUCTION.
CIRWATT is a multi- ur ose three- hase, four quadrant, digital meter. Its great
versatility is its main feature, allowing it to ada t to the needs of each user.
It has been es ecially designed for installations where the electro-mechanical meters
do not meet current requirements. It is s ecifically for those installations that require a
meter with a tariff system or where electricity billing is done by using load rofiles.
2.- METER MODEL
The different meter configuration o tions covering the needs of each installation are
shown below:
CIRWATT 4__ - _ __ _ - _ _ _ - __
Modo de conexión
Tensión de medida
Precisión
4
05
10
U
4 hilos
Clase 0.5S Activa / Clase 1.0 Reactiva
Clase 1.0 Activa / Clase 2.0 Reactiva
3x57/100V ... 3x230/400V (Multirrango)
Medida de corriente
T5
D1
/5A (Transformador. Máximo 10A eficaces)
10 A (Directo. Máximo 100A eficaces)
FrecuenciaCAutomático (50/ 0Hz)
Comunicaciones
1
2
RS-232
RS-485
Expansión
0Sin entradas/salidas
44 entradas + 3 salidas (optomos)
54 entradas + 3 salidas (relé)
94 entradas + 3 salidas (optoacoplador 24V)
CModelo Mediana Industria
00Revisión
T1/1A (Transformador. Máximo 2A eficaces)
Modelo
Sin comunicaciones 0
3.- SAFETY LEVELS (Seals)
CIRWATT has the necessary seals to ensure that the meter is not tam ered with.
These seals must always be attached once the meter is installed.
•
Terminal cover seals. These are attached
once the equi ment has been installed These
seals revent the modification of the meter
connection.
• Button seal. Bill closure and equi ment
RESET o erations are rotected by these
seals.
• Label Seal. This revents the equi ment
features label from being changed.
(Transformation ratios, integration eriod, ty e
or market and area of installation).
LABEL SEAL
TERMINAL CASING
SEALS
DISPLAY
BUTTON
SETTING BUTTON, BILL
CLOSURE AND METER
START
4 wire 4 Connection mode
Class 0.5S Active / Class 1.0 Reactive 05 Accuracy
Class 1.0 Active / Class 2.0 Reactive 10
3x57/100V ... 3x230/400V (Multirrange) U Measured voltage
/1A (Transformer. Maximum 2A effective) T1 Current measurement
/5A (Transformer. Maximum 10A effective) T5
10 A (Direct. Maximum 100A effective) D1
Automatic (50/ 0 Hz) C Frequency
Without communications 0 Communications
RS-232 1
RS-485 2
Ethernet 3
Without inputs/outputs 0 Expansion
4 inputs + 3 outputs (optomos) 4
4 inputs + 3 outputs (relay) 5
4 inputs + 3 outputs (Optocoupled 24V) 9
Model: Medium sized industry C Model:
Revision 00

Page no. 4
4.- DISPLAY.
The different menus and/or screens may be dis layed by using the key on the
CIRWATT. Pressing the key, for less than 2 seconds (short ress), moves through
the different active menus on the screen. Pressing the same key ( ) for two seconds
(long ress), automatically accesses the different secondary o tions and menus.
09-09-2003 12:23:10
Q1 1+2+3+ T534 NBC
Línieas de fase
activas
Quadrante Alarmas
Tarifas activas
Sentido
energía
Data is dis layed via a one line LCD dis lay es ecially designed for the CIRWATT.
The units and resolution of the energy values are the same as the overflow values in
the meter, i.e. they are the recorder’s values. The units will be kWh or kvarh. The size
of the records will be 8 whole digits (99.999.999)
The units in which any power and energy data is transmitted by the communications
protocol will be kW, kWh, and/or kvarh, independent of what is being displayed.
4.1.- Display Modes.
CIRWATT has different dis lay modes re resenting different information.
4.1.1.- STAND BY Mode
This will always occur as a default, whenever the READING mode is not activated by
ressing or the key not being ressed for 60 seconds even though a menu has been
entered.
4.1.2.- READING Mode
This is activated by a long ress on the key, and dis lays the different o tions to
access data screens or other secondary menu screens. Pressing the key (short
ress) moves through the menu, a long ress ( ressing the key for 2 seconds)
enters the o tion that is flashing on the screen. 60 seconds after the last ress, the
Dis lay returns to STAND BY Mode. The different values dis layed on this screen are
shown in oint 4.4 READING screens mode.
Quadrant
Active hase
lines
Energy
direction
Alarms
Active tariffs

Page no. 5
4.2.- Types of screen.
There are three ty es of screen.
4.2.1.- Stand by screen
The STAND BY screen shows information without the need of using the equi ment’s
key. It will be ty ically used for showing the customer the necessary information to
control the measurement in the easiest way ossible. (This is the default screen)
09-09-2003 12:23:10
Q1 1+2+3+ T534 NBC
4.2.2.- Menu Screen
The MENU screen shows the different o tions to access the data screens or the other
secondary menu screens. It is only used in READING mode.
INFO
INFO FAB
4.2.3.- Data Screen.
The DATA screens show information on a s ecific grou of data. It is only used in
READING mode.
The data lines consist of two fields: one is the code and the other the value of the data.
9 characters are reserved for the code field and the remainder for the value field until
the 20 dis lay characters have been used.
1.18.1.01 000000003
1.18.2.01 000000009
The codes are defined in the following way.
Table 1 Dis lay Codes
Display code B . CD
B
0 Total
1 Contract 1
2 Contract 2
3 Contract 3
Energy urchase Energy sale
CD
18 Total active energy (kWh)
19 Incremental active energy (kWh)l
58 Total Reactive Energy (kvarh)
59 Incremetal reactive energy (kvarh)
16 Maximum demand (kW)
12 Power Excesses
28 Active energy total (kWh)
29 Incremental active energy (kWh)
68 Total Reactive Energy (kvarh)
69 Incremental Reactive Energy
(kvarh)
26 Maximum demand (kW)
22 Power Excesses

Page no.
Display code E . F
E 0 Total
1…10 Tariff eriod
F 1…6 Bill closures (last - first)
Pressing for a long time exits a data screen
Pressing for a long time (for 2 seconds) on the
key exits a
data screen
4.3.- STAND BY Mode screen
The different values dis layed on the STAND BY mode screen are shown below
Table 2 Stand by mode screen
Screens Text Type Comments
r.xxxxx P.xxxxx Link Address and Measurement Point
OBIS Without OBIS
0.18.0
0.28.0
0.58.0
0.68.0
0.78.0
0.88.0
IMP
EXP
Q1
Q2
Q3
Q4
Absolute active energy in ut total
Absolute active energy out ut total
Total Q1absolute reactive energy
Total Q2 absolute reactive energy
Total Q3 absolute reactive energy
Total Q4 absolute reactive energy
DD-MM-YYYY HH:MMSS
SCROLL
Date and Local Time
Al hanumeric indicators’ line
Q1 Quadrant (Q1, Q2, Q3, Q4) (See APPENDIX C)
1+2+3+ Presence of voltage in each hase with its corres onding current
direction.
T123 Current tariff eriods in contracts 1, 2 and 3 res ectively.
C Critical alarm due to internal or external incidents directly affecting
measurement. This will be flashing.
N Non critical alarm not affecting measurement creating a meter
malfunction. This will be flashing.
B Low battery alarm. This will be flashing.
R
P S ecial arameter mode activated.

Page no. 7
4.4.- READING screens mode.
READING mode screens consist of different menus as shown below.
Table 3 Reading mode screens diagram
R
(Reposo)
L
(Raíz)
L1
(Contrato 1)
L11 (Actual)
L12 (Cierre 1)
L13 (Cierre 2)
L14 (Cierre 3)
L15 (Cierre 4)
L1 (Cierre 5)
L17 (Cierre )
L2
(Contrato 2)
L21 (Actual)
L22 (Cierre 1)
L23 (Cierre 2)
L24 (Cierre 3)
L25 (Cierre 4)
L2 (Cierre 5)
L27 (Cierre )
L3
(Contrato 3)
L31 (Actual)
L32 (Cierre 1)
L33 (Cierre 2)
L34 (Cierre 3)
L35 (Cierre 4)
L3 (Cierre 5)
L37 (Cierre )
L4
(Información)
L40 (Indicadores)
L41 (Parámetros contratados)
L42 (Relaciones trasnformación)
L43 (Valores en curso)
L44 (Valores instantáneos)
L45 (Comunicaciones)
L4 (Identificadores)
L47 (Constantes de salida)
Información
Fabricante
Modelo
Número de serie
Fecha de fabricación
Pantalla instalación
Estado Cirwatt
Idioma
L48 (Cambio horario)
Contraste display
R
(Stand by)
L
(Main)
L1
(Contract 1)
L2
(Contract 2)
L3
(Contract)3
L4
(Information)
Manufacturer's
Information
L11 (Actual)
L12 (Closure 1)
L13 (Closure 2)
L14 (Closure 3)
L15 (Closure 4)
L1 (Closure 5)
L17 (Closure )
L21 (Actual)
L22 (Closure 1)
L23 (Closure 2)
L24 (Closure 3)
L25 (Closure 4)
L2 (Closure 5)
L27 (Closure )
L31 (Actual)
L32 (Closure 1)
L33 (Closure 2)
L34 (Closure 3)
L35 (Closure 4)
L3 (Closure 5)
L37 (Closure )
L40 (Indicators)
L41 (Contracted parameters)
L42 (Transformation ratios)
L43 (Current values)
L44 (Instant values)
L45 (Communications)
L4 (Identifiers)
L47 (Output constants)
L48 (Change time)
Model
Series number
Date of manufacture
Installation screen
Cirwatt Status
Language
Display contrast
Manufacturer's
Information

Page no. 8
4.4.1.- Screen L (Main)
This is the first screen accessed in READING Mode. It is a MENU screen giving access
to other, secondary MENU screens.
Table 4 Main screen menus
Screen Text Comments
CONTRACT 1 Accesses values for contract 1
CONTRACT 2 Accesses values for contract 2
CONTRACT 3 Accesses values for contract 3
INFO. Accesses information not relevant to the contracts
MANU INFO Accesses additional information defined by the
manufacturer
L
BACK Returns to STAND BY screen
CIRWATT allows the setting of any of the three contracts such
as PURCHASE or SALE. Below is a possible contract setting
that may be changed according to the needs of the USER
and/or COMPANY.
4.4.2.- Screen L1 (CONTRACT 1, PURCHASE)
This is the screen that accesses information on contract 1. It is a MENU screen that
allows access to other secondary MENU screens.
Table 5 Contract 1 screen
Screen Text Comments
CURRENT Accesses current values for contract 1
CLOSURE 1 DD-MM-YY This shows information on values from
contract 1 closure 1 (most recent)
CLOSURE 2 DD-MM-YY Accesses values for contract 1 closure 2
CLOSURE 3 DD-MM-YY Accesses values for contract 1 closure 3
CLOSURE 4 DD-MM-YY Accesses values for contract 1 closure 4
CLOSURE 5 DD-MM-YY Accesses values for contract 1 closure 5
CLOSURE 6 DD-MM-YY Accesses values for contract 1 closure 6
(oldest)
L1
BACK Returns to the revious screen
4.4.2.1.- Screen L11 (CONTRACT 1: CURRENT)
This screen shows information on current values for contract 1. On entering this menu
two o tions a ear for data dis lay: absolute values and incremental values.
The ABSOLUTE o tion (ABS) dis lays absolute values for active and reactive energy,
as well as ower excesses and maximum demands.
The INCREMENTAL o tion (INC) dis lays the incremental values from the last bill
closure for active and reactive energy, ower excesses and maximum demands.
If no o tion is selected, a short ress will move on to showing Absolute data values as
a default.

Page no. 9
Information is only shown on a screen if it is active, i.e. if certain tariffs or
owers have not been activated, information on these tariffs, maximum
demands or excess ower recordings will not a ear on the screen.
The codes for Absolute values are shown below:
Table 6 Absolute energy value codes for contract 1.
AbS (Absolute)
OBIS Without OBIS
KWH 1.18.1 ABSIMP T1 C1-ACT
KWH 1.18.2 ABSIMP T2 C1-ACT
KWH 1.18.3 ABSIMP T3 C1-ACT
KWH 1.18.4 ABSIMP T4 C1-ACT
KWH 1.18.5 ABSIMP T5 C1-ACT
KWH 1.18.6 ABSIMP T6 C1-ACT
KWH 1.18.0 ABSIMP TOTAL
C1-ACT
Tariff eriods for Active Energy
from the start of measurement
(if active), included in the total
( eriod 0)
1.18.x where x = tariff ( eriod)
KVARh 1.58.1 ABSQ1 T1 C1-ACT
KVARh 1.58.2 ABSQ1 T2 C1-ACT
KVARh 1.58.3 ABSQ1 T3 C1-ACT
KVARh 1.58.4 ABSQ1 T4 C1-ACT
KVARh 1.58.5 ABSQ1 T5 C1-ACT
KVARh 1.58.6 ABSQ1 T6 C1-ACT
KVARh 1.58.0 ABSQ1 TOTAL
C1-CO1
Tariff eriods for Q1 Reactive
Energy from the start of
measurement (if active),
included in the total ( eriod 0)
1.58.x where x = tariff ( eriod)
Power Excesses 1.12.1 EXCES T1 C1-ACT
Power Excesses 1.12.2 EXCES T2 C1-ACT
Power Excesses 1.12.3 EXCES T3 C1-ACT
Power Excesses 1.12.4 EXCES T4 C1-ACT
Power Excesses 1.12.5 EXCES T5 C1-ACT
Power Excesses 1.12.6 EXCES T6 C1-ACT
Excesses since the last bill
closure (if active)
1.12.x where x = tariff ( eriod)
Maximums 1.16.1 MAXDEM T1 C1-ACT
Maximums 1.16.2 MAXDEM T2 C1-ACT
Maximums 1.16.3 MAXDEM T3 C1-ACT
Maximums 1.16.4 MAXDEM T4 C1-ACT
Maximums 1.16.5 MAXDEM T4 C1-ACT
Maximums 1.16.6 MAXDEM T6 C1-ACT
L11
Maximums 1.16.0 MAXDEM TOTAL
C1-ACT
Maximums from bill closure (if
active), included in the total
1.16.x where x = tariff ( eriod)

Page no. 10
The codes for the incremental value codes are shown below:
Table 7 Incremental energy value codes for the meter.
Inc (Incremental)
OBIS Without OBIS
kWh 1.19.1 INCIMP T1 C1-ACT
kWh 1.19.2 INCIMP T2 C1-ACT
kWh 1.19.3 INCIMP T3 C1-ACT
kWh 1.19.4 INCIMP T4 C1-ACT
kWh 1.19.5 INCIMP T5 C1-ACT
kWh 1.19.6 INCIMP T6 C1-ACT
kWh 1.19.0 INCIMP TOTAL
C1-ACT
Consum tion er Active Energy
tariff eriod from the last bill
closure (if active) included in the
total
1.19.x where x = tariff ( eriod)
kvarh 1.59.1 INCQ1 T1 C1-ACT
kvarh 1.59.2 INCQ1 T2 C1-ACT
kvarh 1.59.3 INCQ1 T3 C1-ACT
kvarh 1.59.4 INCQ1 T4 C1-ACT
kvarh 1.59.5 INCQ1 T5 C1-ACT
kvarh 1.59.6 INCQ1 T6 C1-ACT
kvarh 1.59.0 INCQ1 TOTAL
C1-CO1
Consum tion er Q1 Reactive
Energy from the last bill closure
(if active), included in the total
1.59.x where x = tariff ( eriod)
Power Excesses 1.12.1 EXCES T1 C1-ACT
Power Excesses 1.12.2 EXCES T2 C1-ACT
Power Excesses 1.12.3 EXCES T3 C1-ACT
Power Excesses 1.12.4 EXCES T4 C1-ACT
Power Excesses 1.12.5 EXCES T5 C1-ACT
Power Excesses 1.12.6 EXCES T6 C1-ACT
Excesses from the last bill
closure (if active)
1.12.x where x = tariff ( eriod)
Maximum 1.16.1 MAXDEM T1 C1-ACT
Maximums 1.16.2 MAXDEM T2 C1-ACT
Maximums 1.16.3 MAXDEM T3 C1-ACT
Maximums 1.16.4 MAXDEM T4 C1-ACT
Maximums 1.16.5 MAXDEM T4 C1-ACT
Maximums 1.16.6 MAXDEM T6 C1-ACT
L11
Maximums 1.16.0 MAXDEM TOTAL
C1-ACT
Maximums from bill closure (if
active), included in the total
1.16.x where x = tariff ( eriod)

Page no. 11
4.4.2.2.- Screen L12 (CONTRACT 1: CLOSURE 01)
This shows recorded information from contract 1 during the last closure. The screen
acts in the same way as the L11 screen, using Absolute or Incremental values.
Table 8 Absolute energy value codes for contract 1 closure 1
ABS (Absolute)
OBIS Without OBIS
kWh 1.18.1.01 ABSIMP T1 C1-C01
kWh 1.18.2.01 ABSIMP T2 C1- C01
kWh 1.18.3.01 ABSIMP T3 C1- C01
kWh 1.18.4.01 ABSIMP T4 C1- C01
kWh 1.18.5.01 ABSIMP T5 C1- C01
kWh 1.18.6.01 ABSIMP T6 C1- C01
kWh 1.18.0.01 ABSIMP TOTAL
C1- C01
Active energy for each tariff
eriod (if active), from the start
of measurement until the last
closure included in the total
( eriod 0)
1.18.x.01 where x = tariff
( eriod)
kvarh 1.58.1.01 ABSQ1 T1 C1- C01
kvarh 1.58.2.01 ABSQ1 T2 C1- C01
kvarh 1.58.3.01 ABSQ1 T3 C1- C01
kvarh 1.58.4.01 ABSQ1 T4 C1- C01
kvarh 1.58.5.01 ABSQ1 T5 C1- C01
kvarh 1.58.6.01 ABSQ1 T6 C1- C01
kvarh 1.58.0.01 ABSQ1 TOTAL
C1- C01
Q1 Reactive energy for each
tariff eriod (if active), from the
start of measurement until the
last closure included in the
total ( eriod 0)
1.58.x.01 where x = tariff
( eriod)
Power Excesses 1.12.1.01 EXCES T1 C1- C01
Power Excesses 1.12.2.01 EXCES T2 C1- C01
Power Excesses 1.12.3.01 EXCES T3 C1- C01
Power Excesses 1.12.4.01 EXCES T4 C1- C01
Power Excesses 1.12.5.01 EXCES T5 C1- C01
Power Excesses 1.12.6.01 EXCES T6 C1- C01
Excesses from the last billing
eriod (if active)
1.12.x.01 where x = tariff
( eriod)
Maximums 1.16.1.01 MAXDEM T1 C1- C01
Maximums 1.16.2.01 MAXDEM T2 C1- C01
Maximums 1.16.3.01 MAXDEM T3 C1- C01
Maximums 1.16.4.01 MAXDEM T4 C1- C01
Maximums 1.16.5.01 MAXDEM T4 C1- C01
Maximums 1.16.6.01 MAXDEM T6 C1- C01
L12
Maximums 1.16.0.01 MAXDEM TOTALC1-
C01
Maximums from the last billing
eriod (if active) included in the
total
1.16.x.01 where x = tariff
( eriod)

Page no. 12
The variable codes for incremental values are shown below:
Table 9 Incremental energy value codes for closure 1 of contract 1
Inc (Incremental)
OBIS SIN OBIS
kWh 1.19.1.01 INCIMP T1 C1-C01
kWh 1.19.2.01 INCIMP T2 C1- C01
kWh 1.19.3.01 INCIMP T3 C1- C01
kWh 1.19.4.01 INCIMP T4 C1- C01
kWh 1.19.5.01 INCIMP T5 C1- C01
kWh 1.19.6.01 INCIMP T6 C1- C01
Consum tion er Active
Energy tariff eriods from
the last billing eriod (if
active), included in the
total ( eriod 0)
1.19.x.01 where x = tariff
( eriod)
kWh 1.19.0.01 INCIMP TOTAL C1- C01 1.19.x.01 donde x =
tarifa ( eríodo)
kvarh 1.59.1.01 INCQ1 T1 C1- C01
kvarh 1.59.2.01 INCQ1 T2 C1- C01
kvarh 1.59.3.01 INCQ1 T3 C1- C01
kvarh 1.59.4.01 INCQ1 T4 C1- C01
kvarh 1.59.5.01 INCQ1 T5 C1- C01
kvarh 1.59.6.01 INCQ1 T6 C1- C01
kvarh 1.59.0.01 INCQ1 TOTAL
C1- C01
Consum tion er Q1
Reactive Energy tariff
eriods from the last billing
eriod (if active), included
in the total ( eriod 1)
1.59.x.01 where x = tariff
( eriod)
Power Excesses 1.12.1.01 EXCES T1 C1- C01
Power Excesses 1.12.2.01 EXCES T2 C1- C01
Power Excesses 1.12.3.01 EXCES T3 C1- C01
Power Excesses 1.12.4.01 EXCES T4 C1- C01
Power Excesses 1.12.5.01 EXCES T5 C1- C01
Power Excesses 1.12.6.01 EXCES T6 C1- C01
Excesses from the last
billing eriod (if active)
1.12.x.01 where x = tariff
( eriod)
Maximums 1.16.1.01 MAXDEM T1 C1- C01
Maximums 1.16.2.01 MAXDEM T2 C1- C01
Maximums 1.16.3.01 MAXDEM T3 C1- C01
Maximums 1.16.4.01 MAXDEM T4 C1- C01
Maximums 1.16.5.01 MAXDEM T4 C1- C01
Maximums 1.16.6.01 MAXDEM T6 C1- C01
L12
Maximums 1.16.0.01 MAXDEM TOTALC1-C01
Maximums form last billing
eriod (if active) included
in the total ( eriod 0)
1.16.x.01 where x = tariff
( eriod)
4.4.2.3.- Screen L13 (CONTRACT 1: CLOSURE 02)
This shows information on values from contract 1 closure 02. The screen acts the
same as for L12.
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 02 instead of 01.
• For exam le: 1.18.1.02  Absolute active energy consumed, from eriod 1,
enultimate bill closure.
4.4.2.4.- Screen L14 (CONTRACT 1: CLOSURE 03)
Shows information on values recorded for contract 1 closure 03. The screen acts in the
same way as L12.
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 03 instead of 01.
• For exam le: 1.18.1.03  Absolute active energy consumed, from eriod 1, bill
closure 3.

Page no. 13
4.4.2.5.- Screen L15 (CONTRACT 1: CLOSURE 04)
This shows information on values from contract 1 closure 04. The screen acts the
same as for L12.
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 04 instead of 01.
• For exam le: 1.18.1.04  Absolute active energy consumed, from eriod 1, bill
closure 4
4.4.2.6.- Screen L16 (CONTRACT 1: CLOSURE 05)
This shows information on values from contract 1 closure 05. The screen acts the
same way as for L12.
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 05 instead of 01.
• For exam le: 1.18.1.05  Absolute active energy consumed, from eriod 1, bill
closure 5.
4.4.2.7.- Screen L17 (CONTRACT 1: CLOSURE 06)
This shows information on values from contract 1 closure 06. The screen acts in the
same way as L12.
The information is dis layed in exactly the same way as in screen L12, but field F will
have the value 06 instead of 01.
• For exam le: 1.18.1.06  Absolute active energy consumed, from eriod 1, bill
closure 6.
4.4.3.- Screen L2 (CONTRACT 2, PURCHASE)
This screen accesses information on contract 2. It acts in the same way as L1.
All data screens that de end on this screen have the value 2 in grou B of the code.
4.4.3.1.- Screen L21 (CONTRACT 2: CURRENT)
This shows information on current values for contract 2. It acts in the same way as
screenL11, but changes the grou B code from 1 to 2. The data shown are the same
as the indicators on screen L11.
Data is dis layed with zeros to the left to fill u the length of the dis lay.
• For exam le: 2.16.2  Absolute, current maximum demand for eriod 2 and for
contract 2.
4.4.3.2.- Screen L22 (CONTRACT 2: CLOSURE 01)
This shows information on the current values for contract 2. It acts in the same way as
screen L12, but changes the grou B code from 1 to 2. The data shown is the same as
that shown on screen L11.

Page no. 14
Data is dis layed with zeros to the left to fill u the length of the data field dis lay.
• For exam le: 2.18.2.01  Absolute active energy consumed, from eriod
2, enultimate bill closure from contract 2.
4.4.3.3.- Screen L23, L24, L25, L26, L27 (CONTRACT 2: CLOSURES 02 TO 06)
This shows recorded information on values from contract 2 from the closures rior to
the last closure. It acts in the same way as screens L13 L17 changes the grou B code
from 1 to 2.
4.4.4.- Screen L3 (CONTRACT 3, SALE)
This screen accesses information on contract 3. It acts the same as screen L11,
however the codes change according to the Table 1 Dis lay Codes age 5.
4.4.4.1.- Screen L3-L37 (CONTRACT 3: CURRENT AND CLOSURES 01 TO 06)
Shows information on values recorded for contract 3. A sam le screen 31 is shown
below:
Table 10 Absolute values screen for contract 3 closure 1
AbS (Absolute)
OBIS Without OBIS
kWh 3.28.1 ABSEXP T1 C3-ACT
kWh 3.28.2 ABSEXP T2 C3-ACT
kWh 3.28.3 ABSEXP T3 C3-ACT
kWh 3.28.4 ABSEXP T4 C3-ACT
kWh 3.28.5 ABSEXP T5 C3-ACT
kWh 3.28.6 ABSEXP T6 C3-ACT
kWh 3.28.0 ABSEXP TOTAL C3-
ACT
Tariff eriods for Active Energy
from the start of measurement
(if active), included in the total
3.28.x where x = tariff ( eriod)
kvarh 3.68.1 ABSQ2 T1 C3-ACT
kvarh 3.68.2 ABSQ2 T2 C3-ACT
kvarh 3.68.3 ABSQ2 T3 C3-ACT
kvarh 3.68.4 ABSQ2 T4 C3-ACT
kvarh 3.68.5 ABSQ2 T5 C3-ACT
kvarh 3.68.6 ABSQ2 T6 C3-ACT
kvarh 3.68.0 ABSQ2 TOTAL C3-ACT
Tariff eriods for Q2 Reactive
Energy from the start of
measurement (if active),
included in the total
3.68.x where x = tariff ( eriod)
Power Excesses 3.22.1 EXCES T1 C1- C01
Power Excesses 3.22.2 EXCES T2 C1- C01
Power Excesses 3.22.3 EXCES T3 C1- C01
Power Excesses 3.22.4 EXCES T4 C1- C01
Power Excesses 3.22.5 EXCES T5 C1- C01
Power Excesses 3.22.6 EXCES T6 C1- C01
Excesses from the last billing
eriod (if active)
1.12.x.01 where x = tariff
( eriod)
Maximums 3.26.1 MAXDEM T1 C3-ACT
Maximums 3.26.2 MAXDEM T2 C3-ACT
Maximums 3.26.3 MAXDEM T3 C3-ACT
Maximums 3.26.4 MAXDEM T4 C3-ACT
Maximums 3.26.5 MAXDEM T5 C3-ACT
Maximums 3.26.6 MAXDEM T6 C3-ACT
L31-
L37
Maximums 3.26.0 MAXDEM TOTAL C3-
ACT
Maximums from the bill closure
(if active), included in the total
3.26.x where x = tariff ( eriod)

Page no. 15
The codes for the incremental value variables are shown below:
Table 11Incremental values screen for contract 3 closure 1
Inc (Incrementales)
OBIS SIN OBIS
kWh 3.29.1
ABSEXP T1 C3-ACT
kWh 3.29.2
ABSEXP T2 C3-ACT
kWh 3.29.3
ABSEXP T3 C3-ACT
kWh 3.29.4
ABSEXP T4 C3-ACT
kWh 3.29.5
ABSEXP T5 C3-ACT
kWh 3.29.6
ABSEXP T6 C3-ACT
kWh 3.29.0
ABSEXP TOTAL C3-ACT
Consumption per Active Energy tariff
periods from the last billing period (if
active), included in the total
3.29. .01 where = tariff (period)
kvarh 3.69.1
ABSQ2 T1 C3-ACT
kvarh 3.69.2
ABSQ2 T2 C3-ACT
kvarh 3.69.3
ABSQ2 T3 C3-ACT
kvarh 3.69.4
ABSQ2 T4 C3-ACT
kvarh 3.69.5
ABSQ2 T5 C3-ACT
kvarh 3.69.6
ABSQ2 T6 C3-ACT
Power Excesses
3.69.0
ABSQ2 TOTAL C3-ACT
Consumption per Q2 Reactive Energy
tariff periods from the last billing
period (if active), included in the total
3.69. .01 where = tariff (period)
E cesses from last billing period (if
active)
3.22. .01 where = tariff (period)
Power Excesses 3.22.1
EXCES T1 C1- C01
Power Excesses 3.22.2
EXCES T2 C1- C01
Power Excesses 3.22.3
EXCES T3 C1- C01
Power Excesses 3.22.4
EXCES T4 C1- C01
Power Excesses 3.22.5
EXCES T5 C1- C01
Maximums 3.22.6
EXCES T6 C1- C01
E cesos del último período de
facturación (si están activos)
3.22. donde = tarifa (período)
Ma imums from the last billing period
(if active ) included in the total
3.26. .01 where = tariff (period)
Maximums 3.26.1
MAXDEM T1 C3-ACT
Maximums 3.26.2
MAXDEM T2 C3-ACT
Maximums 3.26.3
MAXDEM T3 C3-ACT
Maximums 3.26.4
MAXDEM T4 C3-ACT
Maximums 3.26.5
MAXDEM T5 C3-ACT
Maximums 3.26.6
MAXDEM T6 C3-ACT
L31-
L37
Maximums 3.26.0
MAXDEM TOTAL C3-ACT
Má imas del último período de
facturación (si están activas), incluido
el total
3.26. .01 donde = tarifa
(período)
4.4.5.- Screen L4 (INFORMATION)
This screen accesses information not relevant to the contract billing values. This is a
MENU screen. It rovides access to other de endant MENU screens as shown below:
Table 12 Screen L4. Information.
Screens Text Comments
L40 OPERATIONAL
INDICATORS
This is used to check the ro er working of the
equi ment in all its main areas during installation
or during later, on site checks.
L41 POWER
CONTRACTS
This is used to indicate the values of the
contracted owers. It is a lied to calculate
ower excesses.
L42 TRANSFORMATION
RATIOS This shows information on transformation ratios.

Page no. 1
Screens Text Comments
L43 CURRENT VALUES
This shows information on current ower,
maximum demand, totals and ower from the last
integration eriod (15 minutes as a default).
L44 INSTANT VALUES This shows information on the instant values of
different electrical magnitudes.
L45 COMMUNICATIONS This shows information on the different
arameters of the communications orts.
L46 IDENTIFIERS
This shows information on the equi ment's
different identifiers, included those for the
IEC870-5-102 rotocol.
L47 OUTPUT
CONSTANTS
This shows information on the out ut im ulse
values.
L48 TIME CHANGE This shows information on the dates of the time
change.
L49 BACK Returns to the revious screen.
4.4.6.- Screen L40 (INFORMATION: INDICATORS)
This screen shows information on the o erating indicators. It is used to check the
ro er working of the equi ment in all its main areas during installation or during later,
on site checks. It is a DATA screen
As these indicators do not belong to a s ecific contract, but are general data, field B
has the value 0.
Table 13 Screen L40. Indicators.
Code
Screen Text OBIS No OBIS Comments
0.13.38
.ej. 1 C.ACT
ACTIVE QUADRANT: This indicates the
direction of the active or reactive energy or
quadrant (1,2,3 or 4)
e.g. 0.13.38 1 shows that it is in quadrant 1
0.12.38
.ej. 123
PRES.V
PRESENCE OF VOLTAGE: This indicates
the resence of voltage in each hase
(123 if there is voltage in all, blank if they
do not have voltage)
0.11.38
.ej. 120
SENT.I
CURRENT DIRECTION: This indicates the
direction of im ortation (+) or ex ortation (-
) in each hase (111 if they are im orted,
222 if ex orted, 000 if there is none)
0.18.128
.ej. 633
TAR.AC
ACTIVE TARIFF FOR EACH CONTRACT:
This indicates the active tariff at the time of
reading for each contract (contract 1,
contract 2, contract 3)(values form 1 to 9
for each contract
e.g.:. 633
0.96.2.4
.ej. 0 MODO ‘P
PARAMETERISATION MODE: This
indicates if the arameterisation mode is
enabled (0 disabled, 1 enabled)
L40
INDICATORS
0.96.5.0
.ej. cnb ALARMA
ALARMS This indicates the alarms defined
in section 4.3. The data field will dis lay
the letters CNB, which will become active
according to the ty e of alarm.

Page no. 17
4.4.6.1.- Screen L41 (INFORMATION: CONTRACTED POWERS)
This screen shows information on the contracted owers for contract 1. It only a lies
to ower excesses in Contract 1. It is a DATA screen.
Table 14 Screen L41. Contracted owers.
Code
Screen Text OBIS No OBIS Comments
1.135.1 C1 T1
1.135.2 C1 T2
1.135.3 C1 T3
1.135.4 C1 T4
1.135.5 C1 T5
L41
CONTRAC
TED
POWERS
1.135.6 C1 T6
This is for the values in kW to 2 decimals
of the contracted owers that will be used
to calculate excesses
1.135.x where x = tariff ( eriod), u to 9, in
the event that no ower has been
contracted for a tariff the value shown will
be 0
B shows the contract number
4.4.6.2.- Screen L42 (INFORMATION: TRANSFORMATION RATIOS)
This screen shows information on the transformation ratios. As this data does not
corres ond to any s ecific contract but is data general to all, field B will have the value
0. It is a DATA screen.
Table 15 Screen L42. Transformation ratios
Code
Screen Text OBIS
No OBIS Comments
0.04.2
I PRI
CURRENT RATIO PRIMARY: This
shows the current ratio rimary to 1
decimal
0.04.5
I SEC
CURRENT RATIO SECONDARY:
This shows the current ratio
secondary to 1 decimal
0.04.3
V PRI
VOLTAGE RATIO PRIMARY: This
shows the voltage ratio rimary to 1
decimal (com ound voltage)
L42
TRANSFOR-
MATION RATIOS
0.04.6
V SEC
VOLTAGE RATIO SECONDARY:
This shows the voltage ratio
secondary to 1 decimal (com ound
voltage)

Page no. 18
4.4.6.3.- Screen L43 (INFORMATION: CURRENT VALUES)
This screen shows information on current ower, maximum ower, totals and ower
from the last integration eriod (15 minutes as a default). As this data does not
corres ond to any s ecific contract but is data general to all, field B will have the value
0. It is a DATA screen.
Table 16 Screen L43. Information: current values.
Code
Screen Text OBIS No OBIS Comments
0.18.0 IMP TOTAL A+: This shows the current total for
Active Energy taken from the system
0.28.0 EXP TOTAL A-: This shows the current total for
Active Energy ex orted to the system
0.58.0 Q1 TOTAL R1 This shows the current total for
Reactive Energy in Quadrant 1
0.68.0 Q2 TOTAL R2: This shows the current total for
Reactive Energy in Quadrant 2
0.78.0 Q3 TOTAL R3: This shows the current total for
Reactive Energy in Quadrant 3
0.88.0 Q3 TOTAL R4: This shows the current total for
Reactive Energy in Quadrant 4
0.14.0 PMD+
CURRENT INPUT POWER: This shows the
average in ut ower that is being integrated
during the current integration eriod
0.24.0 PMD-
CURRENT OUTPUT POWER: This shows
the average out ut ower that is being
integrated during the current integration
eriod
0.15.0 TPMD+
LAST PERIOD INPUT POWER: This shows
the average in ut ower that is being
integrated during the last integration eriod
L43
CURRENT
0.25.0 TPMD-
LAST PERIOD OUTPUT POWER: This
shows the average out ut ower that is
being integrated during the last integration
eriod

Page no. 19
4.4.6.4.- Screen L44 (INFORMATION : INSTANT VALUES)
This screen shows information on the instant values of different electrical magnitudes.
As this data does not corres ond to any s ecific contract but is data general to all, field
B will have the value 0.
Table 17 Screen L44. Instant values
Code
Screen
Text OBIS No OBIS
Comments
0.327.0
V1 VOL
0.527.0
V2 VOL
0.727.0
V3 VOL
VOLTAGE PER PHASE: This shows the
instant Voltage values in each hase
0.317.0
I1 AMP
0.517.0
I2 AMP
0.717.0
I3 AMP
CURRENT PER PHASE: This shows the
instant Current values in each hase
0.337.0
COSFI 1
0.537.0
COSFI 2
0.737.0
COSFI 3
COS Φ PER PHASE: This shows the instant
values of cos Φ in each hase
0.17.0 P kW
INSTANT ACTIVE POWER: This shows the
instant Active Power in each hase with its
sign
0.37.0 Q kvar.
INSTANT REACTIVE POWER: This shows
the instant Reactive Power in each hase with
its sign
L44
INSTANT
0.137.0
FP 3F
AVERAGE POWER FACTOR: This shows the
average instant Power Factor in the three
hases
4.4.6.5.- Screen L45 (INFORMATION: COMMUNICATIONS)
This screen shows information on the different arameters of the communications
orts. As this data does not corres ond to any s ecific contract but is data general to
all, field B will have the value 0.
Table 18 Screen L45. Communications
Code
Screen Text OBIS No OBIS Comments
0.00.0
OPTICO
SETTING THE OPTICAL SERIES
PORT: 000000n (009600 s eed, n
arity)
0.00.1
R1
SETTING THE ELECTRICAL SERIES
PORT 1 OR ETHERNET: 000000n
(009600 s eed, n arity)
0.00.2
R2
SETTING THE ELECTRICAL SERIES
PORT 2 OR ETHERNET: 000000n
(009600 s eed, n arity)
L45
COMMUNICA-
TIONS
0.00.3
MODEM
START UP MODE FOR THE
ELECTRICAL SERIES PORT 1: It will
a ear as data for the ASDU 142 of
the rotocol