CIS VCC-5CL5M Quick start guide

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
Camera Link I/F
5M Pixels CMOS
B/W and Color RAW Cameras
VCC-5CL5M/R
Product Specifications
& Operational Manual
CIS Corporation

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
1
Table of Contents
PAGE
1. Handling Precautions..................................................................................................................................2
2. Product Outline..........................................................................................................................................3
3. System Configuration .................................................................................................................................3
3.1. Camera .............................................................................................................................................3
3.2. Optional Accessories ...........................................................................................................................3
3.3. Free Software ....................................................................................................................................3
3.4. Packaging..........................................................................................................................................3
3.5. Reference for Other Necessary Equipments on the Market ........................................................................3
4. Specifications ............................................................................................................................................4
4.1. General Specifications .........................................................................................................................4
4.2. Functional Specifications......................................................................................................................4
4.3. Environmental Specifications ................................................................................................................5
5. Part Names and Functions...........................................................................................................................6
6. CMOS Spectral Response.............................................................................................................................8
6.1. VCC-5CL5M (Mono).............................................................................................................................8
6.2. VCC-5CL5R (Color)..............................................................................................................................8
7. Dimensions ...............................................................................................................................................9
8. Sensor Optical Axis Accuracy .....................................................................................................................10
9. Output Data Configuration ........................................................................................................................11
9.1. Port Allocation for Base Configuration ..................................................................................................11
9.2. Output Data Array for Base Configuration............................................................................................. 11
10. Remote Communication Function ...............................................................................................................12
10.1. The settings for RS232C serial communication ......................................................................................12
10.2. Control Code....................................................................................................................................12
10.3. How to set a command......................................................................................................................12
11. Function Settings .....................................................................................................................................14
11.1. Output Bit Length and Tap Width ........................................................................................................14
11.2. Shutter Mode ...................................................................................................................................14
11.3. Shutter Time....................................................................................................................................16
11.4. Trigger Input / EEN Output Settings ....................................................................................................17
11.5. Black Level Control Values..................................................................................................................18
11.6. Gain Control Mode ............................................................................................................................18
11.7. White Balance Function ..................................................................................................................... 19
11.8. ROI Function (Region of Interest) .......................................................................................................20
11.9. Sub-Sampling Function......................................................................................................................21
11.10. Flip Function ................................................................................................................................ 22
11.11. Test Pattern Output Function ..........................................................................................................22
12. Factory Settings.......................................................................................................................................22
13. Case for Indemnity (Limited Warranty)........................................................................................................23
14. CMOS Pixel Defect....................................................................................................................................23
15. Product Support.......................................................................................................................................23
16. Ordering Information................................................................................................................................ 23

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
2
1. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical failure or
malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply to damages or defects
caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
Do not use or store the camera in the extremely dusty or humid places.
Do not apply excessive force or static electricity that could damage the camera.
Do not shoot direct images that are extremely bright (e.g., strong light source, sun, etc.). When strong light such as spot
light was shed, blooming or smear may occur. Put the lens cap on when camera is not in use.
Confirm the mutual ground potential carefully before connecting the camera to monitors or computers. Any AC leaks
from the connected devices may cause damages or destroy the camera.
When mounting the camera to a seating base or others, please be careful not to make the lens contact the base. And
refer to the camera drawings and note the restrictions on screws to be used.
When attaching a lens to the camera, remove the C mount lens cap right before installation to avoid dust on the sensor.
When cabling, avoid strong magnetism and electric wave which may cause noises on video images. In such case,
change the positions or wiring of cables. And, please fully aware what type of cables shall be used. The cable type
varies depends on the conditions of frame grabber board to be connected.
For PoCL connection, pin number 1 and 26 are for power, so that a PoCL cable must be used. The maximum length of the
cable for Base Configuration Model 74.25MHz is up to 10m, although it depends on the specifications of the cable itself.
5 seconds shall be waited after power is turned ON to operate the camera properly.

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
3
2. Product Outline
VCC-5CL5M and VCC-5CL5R are Camera Link interfaced, and 5M resolution industrial camera modules. 5M pixels, 2/3
type CMOS sensor is utilized. Entire pixels (2248 x 2048) can be read out at 35fps (at 3 TAP output). 29mm cubic in
size with 5M resolution, yet cost effective cameras.
Features
□Camera settings can be set via serial command communications from the host equipment.
□Global trigger shutter operation.
□Output bit is selectable out of 1tap, 2tap, and 3 tap.
□ROI function
□Sub-sampling function
□Generates HV cross line signals
□29mm cubic in size
3. System Configuration
3.1. Camera
□Camera, VCC-5CL5M or VCC-5CL5R
□C mount lens cap (attached to the camera)
3.2. Optional Accessories
□TBD
3.3. Free Software
□CIS control panel software for evaluation purpose only is downloadable via our web. ※TBD
3.4. Packaging
□Individual Carton
□Master Carton (TBDpcs/carton)
Note) Master carton may vary depends on the quantity to be shipped.
3.5. Reference for Other Necessary Equipments on the Market
□Frame grabber board
・X64-CL Express (Teledyne Dalsa) for Non-PoCL
・GrabLink Express (Euresys) for PoCL
□Mini camera link cable
・SDR –MDR タイプ(3m) 1MB26-L560-00C-300 (3M) for PoCL
・PoCL cable can be used as a non-PoCL cable as well.
□C mount lens
・LM25HC (Kowa Optical) for 1type f25 Mega pixel

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
4
4. Specifications
4.1. General Specifications
4.2. Functional Specifications
Item
Description
(1) Pick up device
Device Type
2/3 type 5M pixels B/W CMOS or Color RAW CMOS
Effective pixel
number
2464(H) x 2056(V)
Unit cell size
3.45μm x 3.45μm
Chip size
8.50mm x 7.13mm Diagonal length 11.1mm
(2) Frame rate
Full Frame 35.84fps (3 TAP), 29.09fps (2 TAP), 14.56fps (1 Tap) clk 74.25MHz
(3) Interface
Camera
PoCL/non-PoCL Base Configuration Model
Camera Link Version 1.2 complied
Video output
digital 8/10/12bit (1 Tap,2 Tap), 8bit (3 Tap)
Output data clock
74.25MHz
(4) Cable length
The maximum length: 10m
(5) Sensitivity
F8 400 lx 30fps (B/W: VCC-5CL5M)
F5.6 200 lx 30fps (RAW: VCC-5CL5R)
(6) Minimum illumination
F1.4 0.1 lx 30fps (B/W: VCC-5CL5M)
F1.4 1.0 lx 30fps (RAW: VCC-5CL5R)
(7) Dust or stains in optical
system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
(8) Power requirements
DC 12V (10.5 ～15V Power IN terminal, 10.5V ～13V Digital I/F terminal)
(9) Power consumption
1.8W
(10) Dimensions
29 x 29 x 29 mm (without protruding portion)
(11) Weight
45g
(12) Lens mount
C-mount flange back：17.526mm
(13) Optical axis accuracy
HV direction positioning accuracy: within φ0.6mm
HV direction rotation accuracy：±0.5°
Decline accuracy to the base surface：±0.2°
(14) Ground
Circuit GND –conductive between chassis
Item
Description
Default
(15) Output bit length
1tap/2tap 8/10/12bit output, 3tap 8bit output clk:74.25MHz
2 tap 8bit
(16) Camera operational
mode
Continuous read out shutter operation
Preset trigger shutter operation
Pulse width trigger shutter operation
Continuous
readout shutter
operation
(17) Shutter time
Preset
Manual
Continuous 11 pattern off ～1/20000s (2tap)
Trigger (Preset) 12 pattern 1/30s ～1/50000s
Continuous 1/30s ～1/20000s (2tap)
Preset/Pulse Width Trigger 6μs ～200ms
Shutter off
(18) Gain control
Preset
Manual
12 pattern x1 ～x128 (0dB ～42dB)
x1: 0 ～x128: 420 (0dB ～42dB) 0.1dB step
x1 (0dB)
(19) The control set value
for black level
0 ～1023 1 step by 12bit
128

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
5
4.3. Environmental Specifications
(20) White balance
WB Mode
Manual
VCC-5CL5R
Through / One push / Manual
R/G gain 0～400%, Color temperature range 2700K～10000K
Through
(21) ROI function
Preset
Manual
Center area 9 pattern
Column Width Range: 264 ～2448 multiples of 12
Row Height Range: 8 ～2048 multiples of 4
Full Scan
(ROI_0)
(22) Sub-sampling
VCC-5CL5M OFF/ON x and y, 1 read and 1 skip
OFF
(23) Flip function
Reverse OFF/ Horizontal/ Vertical/ HV reverse
OFF
(24) Test pattern output
OFF/ Gray scale (mono) / HV Cross line
OFF
(25) Serial communication
settings
System
Baud rate
Data bit
Parity
Stop bit
Flow control
RS232c complied
To be confirmed at ordering
(9600, 19200, 38400, 57600, 115200 bps)
8
None
1
None
115200 bps
Item
Description
(26) Safety/Quality Standard
RoHS Confirm to 2011/65/EU
CE: EMC (Electro Magnetic Compatibility)
1)EMI (Electro Magnetic Interference)
To be applied for EN55022:2010 (Class A)
2)EMS (Electro Magnetic Susceptibility)
To be applied for EN61000-6-2:2005
※The final judgment for EMC shall be complied as a whole system.
(27) Durability
Vibration
ICE 60068-2-6 complied
Acceleration : 98m/s2 (10G)
Frequency : 20～500 Hz, 1min/oct
Direction : X, Y, and Z 3 directions
Testing time : 120 min for each direction
Shock
IEC 60068-2-27 complied
Level ：980m/s2 (100G)
Direction ：±X, ±Y, and ±Z 6 directions
(28) Packaging
Drop impact
IEC 60068-2-31 complied
Height : 60cm
Number of times : 1 time / 6 sides
(29) Operational
environment
Temperature/
Humidity
Temperature: -5 ～45℃
Humidity: 20 ～60%RH with no condensation
(30) Storage environment
Temperature/
Humidity
Temperature: -25 ～60℃
Humidity: 20 ～80%RH with no condensation

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
6
5. Part Names and Functions
34
56 7
1
2
1. Lens holder
To mount a C mount lens.
Screw length from the lens mount surface shall be less than 6mm. And protruding portion of the lens shall be less
than 8mm.
2. Image sensor / Optical filter
CMOS image sensor surface.
A dummy glass is attached on the surface of the sensor (VCC-5CL5M).
3. Status LED
Red LED lights when the camera is connected and power is turned ON. When camera internal setting is completed,
Green LED lights (controllable)
4. 6pins circular connector for external control
This is the connector to be used for trigger shutter operation or to supply power other than PoCL connector.
Usually, power is supplied via PoCL board, but this can be used when power is not enough or when you cannot
supply power from others. Trigger IN signal is electrically insulated.
Never supply power via both 6pins circular connector and camera link connector at the same time.
Input/Output circuit for external control
Input and output signals for external control of 6pins circular connector are electrically insulated. Trigger in terminal
(TRIG_IN in the drawing) shall be capable of 10mA ～20mA. And, 0.5mA～5mA shall be added to EEN OUT terminal
(EEN_OUT in the drawing) as load resistance for power (3.3V～20V).
1
2
3 4
5
6
HR10A-7R-6PB
(Hirose)
Pin No.
Signal Name
Description
1
Power IN
non-PoCL: Power Input
(DC 12V typical)
2
NC
Not used
3
EEN OUT
Exposure Enable Output
(Open Collector)
4
Trigger IN-
Trigger Input- (Isolated)
5
Trigger IN+
Trigger Input+ (Isolated)
6
GND
GND (for Pin 1)

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
7
TRIG_IN
Ex. TC7S34
(10mA to 20mA)
TRIG IN-
TRIG IN+ 3.3 2
1
220
0.1uF
1uF
1.5K
TLP2309
1
3
5
4
6
EEN_OUT
Camera SideUser Side
3.3V
2SC4081
3.3
4.7K
No Mount
2
1
EEN OUT
470
5V
EXPOSURE
EXT_TRIG
Example
5. Auto selection of Camera Link connector and PoCL/non-PoCL
This is the camera link connector for video signals/camera control.
Cables to be used varies depends on the conditions for the board to be connected.
For PoCL connection, pin number 1 and 26 are for power, so that a PoCL cable must be used.
For non-PoCL connection, pin number 1 and 26 are for GND, so that non-PoCL cable must be used.
Never supply power via both 6pins circular connector and camera link connector at the same time.
6. Product Name Plate
When you need to contact CIS for the analysis or questions, please let us know of its model name and serial number
on the product name plate.
7. Screw holes for camera installation
Screw holes to attach the camera. M3 (Depth 3) x 3, M2 (Depth 3) x 6
Camera Link Base Configuration
PoCL/non-PoCL
12226-1100-00PL (3M)
Pin No.
Signal Name
Description
1,26
Power IN or
GND
PoCL : DC 12VPower Input
non-PoCL: GND
13,14
GND
GND
2,15
X0-, X0+
X0_OUT0
differential pair for transmission
3,16
X1-, X1+
X1_OUT1
differential pair for transmission
4,17
X2-, X2+
X2_OUT2
differential pair for transmission
5,18
Xclk-, Xclk+
CLK OUT
differential pair for transmission
6,19
X3-, X3+
X3_OUT3
differential pair for transmission
7,20
SerTC+, SerTC-
RXD Input
differential pair for reception
8,21
SerTFC-, SerTFC+
TXD Output
differential pair for transmission
9,22
CC1-, CC1+
Trigger Input
differential pair for reception
10,23
CC2+, CC2-
Reserve
differential pair for reception
11,24
CC3-, CC3+
Not used
12,25
CC4+, CC4-
Not used

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
8
6. CMOS Spectral Response
※The lens characteristics and illuminant characteristics are excluded.
6.1. VCC-5CL5M (Mono)
6.2. VCC-5CL5R (Color)

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
9
7. Dimensions

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
10
8. Sensor Optical Axis Accuracy

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
11
9. Output Data Configuration
9.1. Port Allocation for Base Configuration
9.2. Output Data Array for Base Configuration
P_A7
P_A6
P_C6
P_B7
P_B6
LVAL
P_C5
X3_OUT3
X2_OUT2
DVAL
EEN
P_C7
FVAL
P_C2
X1_OUT1
P_C1
P_C0
P_B5
P_B4
P_B3
P_B2
P_C4
P_C3
CLK_OUT
P_A0
P_B1
X0_OUT0
P_B0
P_A5
P_A2
P_A1
P_A4
P_A3
Port
8bit Output 1～3Tap
10bit Output 1～2Tap
12bit Output 1～2Tap
Port A0
DA[0] LSB
DA[0] LSB
DA[0] LSB
Port A1
DA[1]
DA[1]
DA[1]
Port A2
DA[2]
DA[2]
DA[2]
Port A3
DA[3]
DA[3]
DA[3]
Port A4
DA[4]
DA[4]
DA[4]
Port A5
DA[5]
DA[5]
DA[5]
Port A6
DA[6]
DA[6]
DA[6]
Port A7
DA[7] MSB
DA[7]
DA[7]
Port B0
DB[0] LSB
DA[8]
DA[8]
Port B1
DB[1]
DA[9] MSB
DA[9] MSB
Port B2
DB[2]
DA[10]
Port B3
DB[3]
DA[11]
Port B4
DB[4]
DB[8]
DB[8]
Port B5
DB[5]
DB[9] MSB
DB[9]
Port B6
DB[6]
DB[10]
Port B7
DB[7] MSB
DB[11] MSB
Port C0
DC[0] LSB
DB[0] LSB
DB[0] LSB
Port C1
DC[1]
DB[1]
DB[1]
Port C2
DC[2]
DB[2]
DB[2]
Port C3
DC[3]
DB[3]
DB[3]
Port C4
DC[4]
DB[4]
DB[4]
Port C5
DC[5]
DB[5]
DB[5]
Port C6
DC[6]
DB[6]
DB[6]
Port C7
DC[7] MSB
DB[7]
DB[7]

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
12
10. Remote Communication Function
Via camera link serial communication function, the camera can be controlled.
10.1. The settings for RS232C serial communication
Baud rate
115,200bps ※
Data
8bit
Stop bit
1bit
Parity
Not used
XON/XOFF
Not used
※Communication speed (Baud rate) shall be specified at ordering, selectable out of 9600, 19200, 38400,
57600, and 115200 bps. Please be noted that this is not selectable by user settings, but only by factory
settings at its delivery.
10.2. Control Code
・The total control code conforms to ASCII code.
・A control code consists of command, parameter, and CR (0x0d). The changes and acquisition of setting
parameters can be done by issuing commands from the host PC.
10.3. How to set a command
{Command Name} {Parameter 1} {Parameter 2} {Parameter 3}…
・Input of ｛Parameter n｝
-In case of Hexadecimal number:
Start from “0x”or “0X”
Either capital letters or lower case can be input. (a～f, A～Fare both acceptable).
Input range: 0x0000～0xFFFF
-In case of Decimal number:
Only ‘0’～’9’are acceptable.
Input range: 0～65535
・When the camera is booted, prompt, ”> “, will be shown after the command is processed.
・Input a command in capital letters
・Maximum number of input character is 80.
・Separate between a command and a parameter by one space.
・From the head of input character to the linefeed code CR (0x0d) or LF (0x0a) is analyzed as one command.
・Please refer to the Section 11, Function Settings, for the details of address and data settings.
・The sent command will be echoed back after it is received.
Command
Parameter 1
Parameter 2～7
Function
GU
Address
not used
Obtain setting information
SU
Address
Data
Change of camera settings
INIT
not used
not used
Restore factory settings
SAVE
not used
not used
Save the camera settings
GSI
not used
Data
Camera information
Data 1: Model name
GVI
not used
Data
Camera Version information
Data 1: Micon Firm Version
2: FPGA HDL Version

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
13
【Example of Get Command】
To acquire information on the command number 10
[Send] GU[sp]10[¥r] or[¥n]
[Returned Value] 50[¥r] [¥n] [Acquired data + Line feed]
[Returned Value] [¥r] [¥n] [Line feed]
[Returned Value] >[sp] [Prompt + Space]
【Example of Set Command】
To set 30 to the command number 10
[Send] SU[sp]10[sp]30[¥r]or[¥n]
[Returned Value] [¥r] [¥n] [Line feed]
[Returned Value] >[sp] [Prompt + Space]
【Example of SAVE Command】
[Send] SAVE[¥r]or[¥n]
[Returned Value] [¥r] [¥n] [Line feed]
[Returned Value] >[sp] [Prompt +Space]
[¥r]=CR(0x0D)
[¥n]=LF(0x0A)
[sp]=Space(0x20)

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
14
11. Function Settings
11.1. Output Bit Length and Tap Width
11.2. Shutter Mode
Continuous readout shutter operation Continuous Shutter Mode
・This is the mode to read out video data continuously. Exposure time overlaps the readout period.
・No external trigger input signals are needed but it does free run.
・Shutter time is the preset shutter time set in advance.
・When read out cycle changes by ROI function, faster shutter time than the ready out cycle must be set.
Formula for shutter time to read out at Continuous Shutter Mode
3tap Shutter time = (Setting Value) x 1line: 13.4μs + 13.7μs ≪ROI frame rate
2tap Shutter time = (Setting Value) x 1line: 16.5μs + 13.7μs ≪ROI frame rate
1tap Shutter time = (Setting Value) x 1line: 33.0μs + 13.7μs ≪ROI frame rate
Formula for frame rate to read out at Continuous Shutter Mode (including ROI function)
3tap ROI frame rate = ((Active Vline) + 32 = (V total lines)) x 1line: 13.4μs
2tap ROI frame rate = ((Active Vline) + 32 = (V total lines)) x 1line: 16.5μs
1tap ROI frame rate = ((Active Vline) + 32 =( V total lines)) x 1line: 33.0μs
Address
Data
Description
2
0
1
2
3
4
5
6
7
3Tap 8bit Output
2Tap 8bit Output (default)
2Tap 10bit Output
2Tap 12bit Output
1Tap 8bit Output
1Tap 10bit output
1Tap 12bit Output
Reserve
35.84fps 74.25MHz
29.09fps 74.25MHz
29.09fps 74.25MHz
29.09fps 74.25MHz
14.56fps 74.25MHz
14.56fps 74.25MHz
14.56fps 74.25MHz
Address
Data
Description
3
0
1
2
3
Continuous read out shutter operation
Continuous Shutter Mode (default)
Preset trigger shutter operation
Preset Trigger Shutter Mode
Pulse width trigger shutter operation
Pulse Width Control Trigger Shutter Mode
Reserve

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
15
Horizontal Timing at Full Scan (Reference)
aa: 2448 clk
bb: 3 clkaa: 1224 clk
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
2 tap DA 1
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
2447
1
VIDEO
LVAL/DVAL
2448
2447
2
3 5
3
CLK : 74.25MHz
～ ～
Blank 2
1
1 tap DA
2445 31
22448 4 6 2446 42
2 tap DB
bb: 180 clk
41
52
63
24462443
24472444
24482445
258
369
bb: 3 clk
aa: 816 clk
1 4 7
3 tap DA
3 tap DB
3 tap DC
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ ・
Blank
Blank
Black
1 line (2451 clk =33.0μs)
1 line (1227 clk =16.5μs)
1 line (996 clk =13.4μs)
Vertical Timing at Full Scan (Reference for continuous read operation)
LVAL
1/2/3 Tap
VIDEO
20482047
3
1 frame 2080 lines
FVAL
Exposure setting time
1 2
2048
Black
Exposure time
3
1 2
Output 32
Preset Trigger Shutter Operation (Preset Trigger Shutter Mode)
・This is to detect the signal edge of external trigger input and read out video data after completion of exposure.
・Shutter time for exposure period is the preset shutter time set in advance.
Pulse Width Trigger Shutter Operation (Pulse Width Control Trigger Shutter Mode)
・This is to detect the signal edge of external trigger input and read out video after completion of exposure.
・Shutter time for exposure period is the pulse width of the trigger input signal.
Formula for shutter time to read out at Trigger Shutter Mode
All in common for 3tap, 2tap, and 1tap
Preset Trigger Shutter time = (Setting Value) + 14μs
Pulse Width Trigger Shutter time = (Trigger pulse width) + 14μs

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
16
Formula for the shortest trigger input cycle (including ROI function) at Trigger Shutter Mode
3tap Shortest Interval on Trigger input = (Shutter time) + ((Active Vline) + 33) x 1line: 13.4μs
2tap Shortest Interval on Trigger input = (shutter time) + ((Active Vline) + 33) x 1line: 16.5μs
1tap Shortest Interval on Trigger input = (Shutter time) + ((Active Vline) + 33) x 1line: 33.0μs
Trigger Shutter Operation at Full San (Reference)
TRIG IN
EEN_out
(Preset Shutter Value)
FVAL
2053 lines
(TRIG_IN Pulse Width)
Tw: 6μs(min)
Minimum Trigger Interval = Active Line + Exposure Time + 33 lines
TRIG IN
VIDEO
Exposure time
27～28 lines
DVAL
0.4μs14.4μs
Tw: 6μs～250ms
Black
Exposure (setting value)
2048 lines
LVAL
11.3. Shutter Time
Preset Shutter Time
Continuous Shutter Mode
Address
Data
Description
23
0 (off)
1
2
3
4
5
6
7
8
9
10
3 tap
2 tap
1 tap
Shutter
1/35s
1/75s
1/125s
1/200s
1/370s
1/750s
1/1500s
1/3000s
1/6000s
1/12500s
1/25000s
Time
27.0ms
13.5ms
8.13ms
5.41ms
2.71ms
1.35ms
658μs
322μs
161μs
81μs
41μs
Shutter
1/30s
1/60s
1/100s
1/150s
1/300s
1/600s
1/1250s
1/2500s
1/5000s
1/10000s
1/20000s
Time
33.3ms
16.7ms
10.0ms
6.66ms
3.33ms
1.66ms
807μs
394μs
196μs
96μs
47μs
Shutter
1/15s
1/30s
1/50s
1/75s
1/150s
1/300s
1/650s
1/1250s
1/2500s
1/5500s
1/12500s
Time
66.7ms
33.3ms
20.0ms
13.3ms
6.65ms
3.32ms
1.60ms
773μs
377μs
179μs
80μs
15
Manual Shutter as Continuous mode Address 24 setting value

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
17
Preset Trigger Shutter Mode
Manual Shutter Time Values
11.4. Trigger Input / EEN Output Settings
Address
Data
Description
23
0
1
2
3
4
5
6
7
8
9
10
11
Shutter 1tap/2tap/3tap
1/30s
1/60s
1/100s
1/150s
1/300s
1/600s
1/1250s
1/2500s
1/5000s
1/10000s
1/20000s
1/50000s
Time
33330μs
16670μs
10000μs
6670μs
3330μs
1670μs
800μs
400μs
200μs
100μs
50μs
20μs
15
Manual Shutter as Preset Trigger mode Address 24 setting value
Address
Data
Description
24
12bit
24bit
Continuous shutter mode
Setting range = (Total line) –2 line step
Shutter_time_3tap (μs) = setting value x 1line: 13.4μs + 13.7μs
Shutter_time_2tap (μs) = setting value x 1line: 16.8μs + 13.7μs
Shutter_time_1tap (μs) = setting value x 1line: 33.1μs + 13.7μs
Trigger shutter mode 1/50000s ～1/5s
Setting range = 6μs ～200ms 1μs step
Preset Shutter_time (μs) = setting value + 14μs
Width Shutter_time (μs) = (Trigger Pulse Width) + 14μs
Address
Data
Description
4
0
1
2
3
4
5
Trigger input
Camera Link CC1 Side , Positive Edge (default)
Camera Link CC1 Side , Negative Edge
6pin Connector Trig + , Positive Edge
6pin Connector Trig + , Negative Edge
6pin Connector Trig - , Positive Edge
6pin Connector Trig - , Negative Edge
17
0
1
EEN Output
Positive logic (default)
Negative logic

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
18
11.5. Black Level Control Values
** default: 128 is a referenced value and it could be changed to adjust black level at ex-factory.
11.6. Gain Control Mode
Manual Gain Control Values
Noises on the images may be noticeable when gain is increased. Under x16 (24dB) is recommended.
Address
Data
Description
7
10bit
0 ～255 default: ** 128 1 step by 12bit
(mono) Black level: 8 /8bit output (default)
32 /10bit output
128 /12bit output
Address
Data
Description
20
0
1
2
3
4
5
6
7
8
Manual Preset Gain 0dB (default)
Manual Preset Gain 3.5dB
Manual Preset Gain 6dB
Manual Preset Gain 9.5dB
Manual Preset Gain 12dB
Manual Preset Gain 15.5dB
Manual Preset Gain 18dB
Manual Preset Gain 21.5dB
Manual Preset Gain 24dB
X1
x1.5
x2
x3
x4
x6
x8
x12
x16
9
10
11
Manual Preset Gain 30dB
Manual Preset Gain 36dB
Manual Preset Gain 42dB
x32
x64
x128
15
Manual Gain Control Address 21 setting value
Address
Data
Description
21
10bit
x1: 0 (default) ～x128: 420 (0 ～42dB )
0.1dB step

VCC-5CL5M/R Rev.905-0073-00
©2016 CIS Corporation. All rights reserved.
19
648x480
Detection Area of One Push WB
2464
2056
GB
RG
(0,0)
Color Bayer Pattern
11.7. White Balance Function
Valid only for the color model, VCC-5CL5R
White Balance Mode
One Push Trigger
Mode 1: Valid when One Push White Balance mode is selected.
White balance is adjusted only once when the Address34
Data1 command is sent.
Adjusted value is kept even when modes are changed,
unless otherwise this command is sent again.
The detection area to see the balance of adjustment is
the area for 648 (H) x 480(V) ROI_8
Manual White Balance Value
Mode 2: Valid when Manual White Balance mode is selected.
This is the function to adjust white balance of the image, with adjusting Red/Blue gain manually,
when “Gain Control Mode”is selected as the Master Gain with the Raw output camera.
Adjustable color temperature range = 2700K ～10000K
Example of manual color temperature settings
Address
Data
Description
30
0
1
2
Through mode (Rgain= Ggain=Bgain)
One Push White Balance mode
Manual White Balance mode
Address
Data
Description
34
1
One Push Trigger
Address 34 is only SU Command
Address
Data
Description
31
10bit
Red gain
0 ～400% default: 100
33
10bit
Blue gain
0 ～400% default: 100
Color temperature
MWB R/B gain
R gain (%)
B gain (%)
2800K
126
378
3200K
144
322
4000K
174
257
4500K
189
232
5500K
213
201
6500K
232
182
9000K
264
156