CIS VCC-FC60FR19CL Quick start guide

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
4M Resolution CMOS
Color Camera Link
VCC-FC60FR19CL
Product Specification
& Operational Manual
CIS Corporation
En
g
lish

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
2
Table of Contents
PAGE
1. Scope of Application .............................................................................................................................................. 3
2. Handling Precautions ............................................................................................................................................... 3
3. Product Outline ..................................................................................................................................................... 4
4. Specification.......................................................................................................................................................... 5
4.1. General Specification .................................................................................................................................. 5
4.2. Camera Output Signal Specification ............................................................................................................. 7
4.3. CMOS Spectral Response (Representative Value) .......................................................................................... 8
4.4 Video Output Format .................................................................................................................................. 9
5. Function Settings................................................................................................................................................. 10
6. External Connector Pin Assignment....................................................................................................................... 13
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) equivalent................................................................. 13
6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)....................................................................... 14
6.3. PoCL Selection Switch (SW1)..................................................................................................................... 14
7. Timing Chart ....................................................................................................................................................... 15
7.1. Horizontal Synchronous Signals Timing (1Tap Base Configuration Mode: 17fps)........................................... 15
7.2. Vertical Synchronous Signals Timing (1Tap Base Configuration Mode: 17fps)................................................ 15
7.3. Horizontal Synchronous Signals Timing (2Tap Base Configuration Mode: 34fps)........................................... 16
7.4. Vertical Synchronous Signals Timing (2Tap Base Configuration Mode: 34fps)................................................ 16
7.5. Horizontal Synchronous Signals Timing (4Tap Medium Configuration Mode: 68fps) * Initial Setting ............... 17
7.6. Vertical Synchronous Signals Timing (4Tap Medium Configuration Mode: 68fps)........................................... 17
7.7. Horizontal Synchronous Signals Timing (8Tap Full Configuration Mode: 135fps)........................................... 18
7.8. Vertical Synchronous Signals Timing (8Tap Full Configuration Mode: 135fps)................................................ 18
7.9. Fixed Trigger Shutter Mode ....................................................................................................................... 19
7.10. Pulse Width Trigger Shutter Mode.............................................................................................................. 20
7.11. Internal Trigger Mode ............................................................................................................................... 21
8. Partial Scan Mode ................................................................................................................................................ 22
9. Remote Communication Function.......................................................................................................................... 24
10. Initial Settings ..................................................................................................................................................... 26
11. CMOS Optical Axis Accuracy ................................................................................................................................. 27
12. Dimensions ......................................................................................................................................................... 28
13. Cases for Indemnity (Limited Warranty) ................................................................................................................ 29
14. CMOS Pixel Defect ............................................................................................................................................... 29
15. Product Support .................................................................................................................................................. 29

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-FC60FR19CL, 4M resolution, Camera Link Color CMOS Camera.
All specifications contained herein are subject to change without prior notice. Reproduction in whole or in
part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not
apply to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
zDo not use or store the camera in the following extreme conditions:
¾Extremely dusty or humid places.
¾Extremely hot or cold places (operating temperature –5 to +4℃5)℃
¾Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
¾Places subject to fluorescent light reflections.
¾Places subject to unstable (flickering, etc.) lighting conditions.
¾Places subject to strong vibration.
zRemove dust or dirt on the surface of the lens with a blower.
zDo not apply excessive force or static electricity that could damage the camera.
zDo not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
zFollow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
z Confirm the mutual ground potential carefully and then connect the camera to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera.
z Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power
supply voltage may cause damages or malfunction of the camera.

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
4
z The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
zThe rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoide noises like chattering when rising.
3. Product Outline
VCC-FC60FR19CL is a Camera Link interfaced and 4M resolution industrial color video camera module.
4M pixels CMOS sensor with diagnal length 15.930mm is utilized. Entire pixels can be read out within
1/68s at Medium Configuration output.
Features
□ Global shutter CMOS sensor is utilized.
□ Camera Link Base, Medium, and Full Configuration are supported.
□ Fixed trigger shutter mode, pulse width trigger shutter mode, and internal trigger mode are
operable.
□ Full frame rates and video output format are as follows.
□ Free Software
¾CIS control panel software for evaluation purpose only is downloadable via our web.
□ Optional Accessories
¾Mount conversion ring from M42 to C mount
¾Mount conversion ring from M42 to F mount
1Tap Base Configuration Mode 17fps 8bit/10bit
2Tap Base Configuration Mode 34fps 8bit/10bit
4Tap Medium Configuration Mode 68fps(Initial Setting) 8bit/10bit
8Tap Full Configuration Mode 135fps 8bit
Initial Setting: 4Tap Medium 68fps 8bit
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
5
4. Specification
4.1. General Specification
(1) Pickup Device Device Type Diagonal Length 15.930mm, Global Shutter type, color CMOS
Effective pixel number 2048(H) x 2048(V)
Unit cell size 5.5μm(H) x 5.5μm(V)
(2) Video Output Frequency
Pixel Clock 72 MHz
1Tap Horizontal frequency: 34.884 kHz Horizontal clock 2064 CLK
Base Configuration Mode:
V
ertical frequency: 16.992 Hz Scanning lines 2053 H
2Tap
Base Configuration Mode:
Horizontal frequency: 69.767 kHz Horizontal clock 1032 CLK
V
ertical frequency: 33.967 Hz Scanning lines 2054 H
4Tap
Medium Configuration Mode:
Horizontal frequency: 139.535 kHz Horizontal clock 516 CLK
V
ertical frequency: 67.834 Hz Scanning lines 2057 H
8Tap
Full Configuration Mode:
Horizontal frequency: 279.070 kHz Horizontal clock 258 CLK
V
ertical frequency: 135.339 Hz Scanning lines 2062 H
(3) Sync. System Internal Sync. System.
(4) Video Output 1Tap Base Configuration
2Tap Base Configuration
4Tap Medium Configuration (Initial Setting)
8Tap Full Configuration
(5) Resolution 2048 TV Lines
(6) Output Format Sensor AD 10bit
Camera Link output 8bit / 10bit (Fixed to 8bit at Full Configuration mode.)
Color RAW output.
(7) Sensitivity F11 2000lx (at Shutter speed 1/68s (OFF), Gain 0dB, and Medium Configuration mode)
(8) Minimum illumination F1.4 2.0lx (at Shutter speed 1/68s (OFF), Gain +12dB, and Medium Configuration mode)
(9) Dust or stains in optical
system
No dust or stain shall be detected on the testing screen with setting the camera aperture at F16.
(10) Power requirements DC+12V±10% 12pins circular connector or PoCL
(11) Power consumption 2.0W (at DC+12V IN, 4Tap Medium Configuration mode, Full frame scan output): Initial setting.
3.0W (at DC+12V IN, 8Tap Full Configuration mode, Partial scan 10lines output)
(12) Dimensions Refer to overall dimension drawing. (H:55mm W:55mm D:25mm excluding projection)
(13) Weight Approx. 125g
(14) IR Cut Filter None
(15) Lens mount M42 Mount * Refer to overall dimension drawing.
(16) Optical axis accuracy Refer to drawing for CMOS Optical Axis Accuracy.
(17) Gain variable range 0dB ～+12dB (Guaranteed range)
(18) White Balance Adjustment
Range
2800～9000K (Manual White Balance) (Guaranteed Range)
(19) Shutter speed variable
range
OFF ～1/50000s
(20) Trigger shutter mode Fixed Shutter Trigger Mode/ Pulse Width Shutter Trigger Mode / Internal Trigger Mode
(21) Partial Scan Full Frame Scan ～ 1 line (1 line / step)
(22) Safety/Quality standards UL: Conform to UL Standard including materials and others.
CE:
EN55022:2006 Class B for Emission
EN61000-6-2:2005 for Immunity
RoHS: Conform to RoHS.
FCC:
T
o be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
6
(23) Durability Vibration
Acceleration : 98m/s2(10G)
Frequency : 20～200 Hz
Direction : X,Y, and Z 3 directions
Testing time : 120min for each direction
Shock No malfunction shall be occurred with 980m/s2(100G) for ±X,±Y, a n d ±Z,
6 directions. (without package)
(24) Operation environment
Temperature
Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temeprature: -5℃～+45℃
※All the specifications specified in this manual is guaranteed under
performance guaranteed temperature.
※All the camera functions operate normally under operation guaranteed
temperature.
Humidity RH 20～80% with no condensation.
(25) Storage Environment Temperature -25℃～+60℃
Humidity RH 20～80% with no condensation.

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
7
100Ω
General Purpose Output 1～4
+5.0V(VCC)
Trigger Input,
General Purpose Input 1
HD74LV1GT32ACME(RENESA)
Voh:3.8V(Min)
Vol:0.55V(Max)
1KΩ
HD74LV1GT14ACME(RENESAS)
Vt-:0.5(Min)
Vt+:1.9V(Max)
100Ω
4.2. Camera Output Signal Specification
(1) Video output data Effective Video Output 2048(H) × 2048(V) At full frame scan mode
(2) Sync. Signal
output
General Purpose Output 1 ：6 pin 12pins Circular Connector
(LVTTL output):
Selectable with Address 034,
General Purpose Output 2 ：7 pin Address 035,
General Purpose Output 3 ：9 pin Address 036,
General Purpose Output 4 ：10 pin And Address 037
LVAL Camera Link output (LVDS):
FVAL
DVAL Selectable with Address 038,
SP And Address 039
(3) Trigger Input Polarity Positive/Negative Selectable Polarity is selectable with
Address 011
Pulse Width
10μs (min.) ～ Approx. 2 frames
Functionally, no upper limitation is set but noises such as dark
noises and shadings might be noticeable at long time exposure.
Trigger Input ：11pin 12pins circular connector
(LVTTL)
: Selectable with address 012.
：CC1 Camera Link input (LVDS)
(4) Partial Scan
Selection
General Purpose Input 1 ：4pin 12pins circular connector
(LVTTL input)
(5) Serial
Communication
SerTC (Serial to Camera) Camera Link input (LVDS）
SerTFG (Serial to Frame Grabber) Camera Link output (LVDS)
(6) Video Signals White Clip Level At Digital 10bit : 3FFh
Setup Level At Digital 10bit : under 002h
(Condition: Gain 0dB)
Dark Shading At Digital 10bit : Both horizontal and vertical
should be under ±00Fh.
(Condition: Gain 0dB)
※ 2 secounds shall be waited after turning on power to get proper camera operation.
12pins circular connector at rear: IO Interface

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
8
4.3. CMOS Spectral Response (Representative Value)
* Lens charcteristics and luminous source charcteristics are not considered.

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
9
・・・
～
～
～
～
2048pixel
GB
(2048)
・・・・・・
2048
～
～
1
～
～
2048 Line
2048pixel
1024 1025
GBGB
(1024) (1024)
2048
1
2048 Line
512
1024 1536
513
1025 1537
・ ・ ・ ・ ・ ・ ・ ・
～
～
～
～
2048 Line
2048pixel
1
512
1024 1536
513
1025 1537
256 768
1280
257 769
1281 1792 1793
2048
(256) (256)
(256)
(256) (256) (256) (256)
(256)
4.4 Video Output Format
(1) 1Tap Base Configuration Mode : 17fps
(2) 2Tap Base Configuration Mode : 34fps
(3) 4Tap Medium Configuration Mode : 68fps (Initial Setting)
(4) 8Tap Full Configuration Mode : 135fps

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
10
5. Function Settings
(Camera functions can be set with serial communications.)
Function Address Data
Gain 001 0: 0 dB : Fixed Gain
1: + 3 dB : Fixed Gain
2: + 6 dB : Fixed Gain
3: + 12 dB : Fixed Gain
4: Manual Gain: over 0～+12dB (Refer to Address 005 and 006.)
Shutter 002 1Tap Mode 2Tap Mode 4Tap Mode 8Tap Mode
0: 1/17s(OFF) 1/34s(OFF) 1/68s(OFF) 1/135s(OFF)
1: 1/30s(OFF) 1/34s(OFF) 1/68s(OFF) 1/135s(OFF)
2: 1/60s 1/60s 1/68s(OFF) 1/135s(OFF)
3: 1/90s 1/90s 1/90s 1/135s(OFF)
4: 1/120s 1/120s 1/120s 1/135s(OFF)
5: 1/150s 1/150s 1/150s 1/150s
6: 1/250s 1/250s 1/250s 1/250s
7: 1/500s 1/500s 1/500s 1/500s
8: 1/1000s 1/1000s 1/1000s 1/1000s
9: 1/2500s 1/2500s 1/2500s 1/2500s
10: 1/5000s 1/5000s 1/5000s 1/5000s
11: 1/10000s 1/10000s 1/10000s 1/10000s
12: 1/20000s 1/20000s 1/20000s 1/20000s
13: 1/30000s 1/30000s 1/30000s 1/30000s
14: 1/45000s 1/45000s 1/45000s 1/45000s
15: 1/50000s 1/50000s 1/50000s 1/50000s
16: Manual Shutter (Refer to Address 009 and 010.)
White Balance 003 0: Through
1: 3200K
2: Through
3: Through
4: Manual White Balance (Refer to Address 049&050, 051&052.)
Trigger Shutter Mode 004 0: Normal Shutter Mode (Trigger OFF)
1: Fixed Trigger Shutter Mode (Shutter speed can be set with address 002.)
2: Pulse Width Trigger Shutter Mode
(Shutter speed can be set with trigger pulse width.)
5: Internal Fixed Trigger Shutter Mode
(According to external trigger signals, the specified numbers of trigger are
generated in the camera.)
6: Internal Pulse Width Trigger Shutter Mode
(According to external trigger signals, the specified numbers of trigger are
generated in the camera.)
Manual Gain 005&006 0～767: 0:0dB ～767:+12dB

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
11
Function Addresss Data
Manual Shutter 009&010 Shutter Speed = 15.41us + (Max Data - (009&010))×3.583us
1Tap Mode 2Tap Mode 4Tap Mode 8Tap Mode
Mini Data 0(58.7ms) 0(29.4ms) 0(14.7ms) 0(7.3ms)
Max Data 16383(15.41us) 8191(15.41us) 4095(15.41us) 2047(15.41us)
※Set the data of address 002 to 016.
Address 009 MSB and address 010 LSB makes total 16bit.
※b0-b1 shall be invalid at 1Tap normal shutter mode setting.
Trigger Polarity 011 0: Positive
1: Negative
Trigger Input 012 0: Camera Link (CC1) Input
1: 12pin Connector(11pin) Input
Output Data Selection 013 0: 8bit Output
1: 10bit output (10bit can not be output at 8Tap Full Configuration mode.)
Partial Scan Mode 015 0: Full Frame Scan Mode
1: Partial Scan Mode
* To control partial scan mode with camera resistor, input “L” signal to
the pin No. 4 of the 12pins circuclar connector, or disconnect.
Partial Scan
Start Position 1
016&017 0～2047:
※Set the data of address 015 to 001.
Address 016 MSB and address 017 LSB makes total 16bit.
Camera internal H Sync
ON/OFF
of trigger input signal
018 0: OFF
1: ON
Partial Scan
Effective Line Number 1
019&020 0～2048: Set 0 when not in use.
※Set the data of address 015 to 001.
Address 019 MSB and address 020 LSB makes total 16bit.
Output image flip vertical 021 0: Normal
1: Flip Vertical
General Purpose Input 1
ON/OFF
022 0: Invalid
1: Valid
Baud Rate 030 0: 9600bps
1: 19200bps
2: 38400bps
3: 57600bps
4: 115200bps
Camera Mode 031 0: 8Tap Full Configuration Mode (135fps)
1: 4Tap Medium Configuration Mode (68fps)
2: 2Tap Base Configuration Mode (34fps)
3: 1Tap Base Configuration Mode (17fps)
Exposure Polarity 032 0: Positive
1: Negative
General Purpose Output 1, 034 0: HD output
General Purpose Output 2, 035 1: FVAL output
General Purpose Output 3, 036 2: Exposure output
General Purpose Output 4 037 3: TRIG Input EN output

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
12
Function Addresss Data
Camera Link SP output 038 0: LVAL output
Camera Link DVAL output 039 1: FVAL output
2: Exposure output
3: TRIG Input EN output
4: DVAL output
5: HD output
Internal Trigger Pulse Width 040&041 0 ～ 65535: Setting Conditions： Address (042&043) > Address (040&041)
Pulse Width = ((Address (040&041)+1) x 3.583μs
Internal Trigger Tact Time 042&043 1 ～ 65535: Setting
Conditions：
Address (042&043) > 0,
Address (042&043) > Address (040&041)
Tact Time = ((Address (042&043)+1) x 3.583μs
Internal Trigger
Repeat number
044 0 ～31: Address (044)+1 time
Manual White Balance R 049&050 256～1023: 256: 0dB ～1023: +12dB
Set the data of address 003 to 004.
Manual White Balance B 051&052 256～1023: 256: 0dB ～1023: +12dB
Set the data of address 003 to 004.
Partial Scan Start Position 1 016&017 0～2047: Set the data of address 015 to 001.
Address 016 MSB and address 017 LSB makes total 16bit.
Partial Scan Effective lines 1 019&020 1～2048: Set 0 when not in use. Set the data of address 015 to 001.
Address 019 MSB and address 020 LSB makes total 16bit.
Partial Scan Start Position 2 207&208 0～2047:
Partial Scan Effective lines 2 209&210 1～2048: Set 0 when not in use.
Partial Scan Start Position 3 211&212 0～2047:
Partial Scan Effective lines 3 213&214 1～2048: Set 0 when not in use.
Partial Scan Start Position 4 215&216 0～2047:
Partial Scan Effective lines 4 217&218 1～2048: Set 0 when not in use.
Partial Scan Start Position 5 219&220 0～2047:
Partial Scan Effective lines 5 221&222 1～2048: Set 0 when not in use.
Partial Scan Start Position 6 223&224 0～2047:
Partial Scan Effective lines 6 225&226 1～2048: Set 0 when not in use.
Partial Scan Start Position 7 227&228 0～2047:
Partial Scan Effective lines 7 229&230 1～2048: Set 0 when not in use.
Partial Scan Start Position 8 231&232 0～2047:
Partial Scan Effective lines 8 233&234 1～2048: Set 0 when not in use.
Initial Settings 254 Input 083 or 053 to set back to initial settings.
Data Save 255 Input 083 or 053 to save the data to EEP-ROM.
※ The data set with 2 Byte shall be set with High Byte first, then set with Low Byte. The camera rewrites
the internal resister when receiving Low Byte.

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
13
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) equivalent
*1. General Purpose Input 1
Via 12pins connector, full frame scan mode and partial scan mode can be switched.
Input Signal Function
L or NA : Full Frame Scan Mode
H : Partial Scan Mode
Set the resistor address 015 to data 0 (full frame scan mode).
When data 1 (partial scan mode) is set to the resistor address 015, 12pins connector control will be
invalid.
*2. General Purpose Output 1～4
The following output signals can be selected by serial communication commands.
Output Signals Address Data
Output 1 034 0: HD output
Output 2 035 1: FVAL output
Output 3 036 2: Exposure output
Output 4 037 3: TRIG Input EN output
Pin No. Initial Settings
1 GND
2 Power Input (DC+12V)
3 GND
4 General Purpose Input 1 Full frame scan / Partial scan *1
5 GND
6 General Purpose Output 1 HD output (Address 034, data 0)*2
7 General Purpose Output 2 FVAL output (Address 035, data 1)*2
8 GND
9 General Purpose Output 3 Exposure output (Address 036, data 2)*2
10 General Purpose Output 4 TRIG Input EN output (Address 037, data 3)*2
11 Trigger Input
12 GND

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
14
1
14
13 26
1
14
13 26
(Base Configuration)
(Medium / Full Configuration)
(CN2)(CN3)
CL
PoCL
(CN1)
(SW1)
6.2. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)
Connector (CN3) Connector (CN2)
6.3. PoCL Selection Switch (SW1)
(1) PoCL ・・・ Set the switch when feeding power via the frame grabber board with PoCL
supported.
※ When the switch is set to PoCL side, power feeding line of CN2 (on Base Configuration
connector side) will be connected to the camera internal power input. At this time, power feeding
line of CN3 (on Medium/Full Configuration connector side) shall be OPEN. When using at
Medium/Full Configuration mode, please contact the frame grabber board manufacturer to make
sure that there would be no problem with the above connection.
(2) CL ・・・ Set the switch when using non-PoCL supported frame grabber board.
Please make sure that the power of feeding side is OFF when changing the switch setting.
If the switch setting is changed while power distribution, malfunction may occur.
Pin No. Pin No. Pin No. Pin No.
1 NA 14 GND 1 GND/+12V(PoCL) 14 GND
2 Y0- 15 Y0+ 2 X0- 15 X0+
3 Y1- 16 Y1+ 3 X1- 16 X1+
4 Y2- 17 Y2+ 4 X2- 17 X2+
5 Yclk- 18 Yclk+ 5 Xclk- 18 Xclk+
6 Y3- 19 Y3+ 6 X3- 19 X3+
7 100Ω20 Terminated 7 SerTC+ 20 SerTC-
8 Z0- 21 Z0+ 8 SerTFG- 21 SerTFG+
9 Z1- 22 Z1+ 9 CC1- (Trigger IN -) 22 CC1+ (Trigger IN +)
10 Z2- 23 Z2+ 10 100Ω23 Terminated
11 Zclk- 24 Zclk+ 11 100Ω24 Terminated
12 Z3- 25 Z3+ 12 100Ω25 Terminated
13 GND 26 NA 13 GND 26 GND/+12V(PoCL)

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
15
LVAL OUT
～ ～
Effective Data: 2048CLK16 CLK
DVAL OUT
・・・・・・・・・・・・
1 H = 2064CLK
～ ～
Camera Link Port A
1 2 3 4
・・・・・・・・・・・・
5 6 7 8
2041
Camera Link CLK:72MHz
～ ～
Video OUT
HD OUT
～ ～
80 CLK
2042
2043 2044
2045
2046 2047
2048
2047
2048
1 2
FVAL OUT
1Frame=
2053H(58.9ms)
Effective Line: 2048 H
Effective Line
DVAL OUT
～ ～
LVAL OUT
～ ～
Effective Line
～ ～～
～
V Blanking:5H
(Read OUT Pulse)
Exposure Time(*1)
Exposure OUT
(*1 ) Exposure Time: Address(009&010): Min0(58.7ms) ～ Max16383 (7.4μs)
2048
1 1
1H=28.667
μs
Video OUT
2048
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing (1Tap Base Configuration Mode: 17fps)
7.2. Vertical Synchronous Signals Timing (1Tap Base Configuration Mode: 17fps)

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
16
LVAL OUT
Effective Data:1024CLK8 CLK
DVAL OUT
1 H = 1032CLK
Camera Link Port B ・・・・・・・・・・・・
Camera Link CLK :72MHz
Camera Link Port A ・・・・・・・・・・・・
・・・・・・・・・・・・ ・・・・・・・・・・・・
Port A Port B
Video OUT
HD OUT
80 CLK
FVAL OUT
1Frame =2054H(29.4ms)
Effective Line:2048 H
Effective Line
DVAL OUT
～ ～
LVAL OUT
～ ～
Effective Line
～ ～～
～
V Blanking:6H
(Read Out Pulse)
Exposure Time (*1)
Exposure OUT
2048
1 1
1H=14.333
μs
Video OUT
(*1 )Exposure Time: Address(009 &010):Min 0(29.4ms) ～ Max8191 (7.4
μs)
2048
7.3. Horizontal Synchronous Signals Timing (2Tap Base Configuration Mode: 34fps)
7.4. Vertical Synchronous Signals Timing (2Tap Base Configuration Mode: 34fps)

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
17
LVAL OUT
～ ～
Effective Data : 512 CLK4 CLK
DVAL OUT
1 H = 516 CLK
～ ～
Camera Link Port D
・・ ・・
Camera Link CLK :72MHz
Camera Link Port C
・・・・・・・・・・・・
1537 1538
Camera Link Port B
・・・・・・・・・・・・
Camera Link Port A
1 2
・・・・・・・・・・・・
1025 1026
513
514
1 2
・・・・・・ ・・・・・・ ・・・・・・ ・・・・・・
Port A
～ ～
Port B
～ ～
Port C
～ ～
Port D
Video OUT
511
1023 1535
2047
HD OUT
～ ～
80 CLK
～ ～
2047 2048
511
512
1535 1536
1023 1024
1024 1025 1026
512 513
514
1536 1537 1538
2048
～ ～～
～
～ ～～
～
2048
1 1
2048
7.5. Horizontal Synchronous Signals Timing (4Tap Medium Configuration Mode: 68fps) * Initial Setting
7.6. Vertical Synchronous Signals Timing (4Tap Medium Configuration Mode: 68fps)

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
18
LVAL OUT
Effective Data :256CLK2 CLK
DVAL OUT
1 H = 258 CLK
Camera Link Port H ・・・・・・・・・・・・
Camera Link CLK :72MHz
Camera Link Port G ・・・・・・・・・・・・
・・
Camera Link Port F ・・・・・・・・・・・・
Camera Link Port E ・・・・・・・・・・・・
Camera Link Port D ・・・・・・・・・・・・
Camera Link Port C ・・・・・・・・・・・・
Camera Link Port B ・・・・・・・・・・・・
Camera Link Port A ・・・・・・・・・・・・
・・ ・・ ・・ ・・ ・・・・ ・・
Port A Port B Port C Port D Port E Port F Port G Port H
Video OUT
HD OUT
80 CLK
～ ～～
～
～ ～～
～
2048
1 1
2048
7.7. Horizontal Synchronous Signals Timing (8Tap Full Configuration Mode: 135fps)
7.8. Vertical Synchronous Signals Timing (8Tap Full Configuration Mode: 135fps)

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
19
Effective Line:2048H
Effective Line
～ ～
Exposure Out
2048
1
Trigger IN
(Re ad O ut P uls e )
LVAL Out
FVAL Out
Video Out
DVAL Out
～ ～
1
Effective Line
Trigger input ignore period
Exposure Time
Exposure Time Delay
(A)
Trigger Input EN
Exposure Out
FVAL Out
～ ～
LVAL Out
1 Tap Base Configuration Mode 137
μs
2 Tap Base Configuration Mode 87
4 Tap Medium Configuration Mode 62
8 Tap Full Configuration Mode 49
LVAL Width Don' t Care
(3H period )
μs
μs
μs
2048
7.9. Fixed Trigger Shutter Mode
□ This is the mode to start exposure with external input trigger signals, and set the exposure time with
serial commands.
□ Trigger operation is CLK Sync. HV-Sync Reset. The delay time (Exposure Time Delay) from
detecting trigger edge in the camera to starting exposure is 370ns.
□ Triggers can be accepted even when outputting video signals. However, trigger signals for
exposure to start the next video output prior to the completion of video transmission for the prior
video output signals can not be accepted.
If the edge part of trigger signals is overlapped with video outputting period, 1 line noise may
detected on the video output screen. To input trigger signals during video output period, set the
data of address 018 to 001 (Trigger input signal, camera internal H sync ON). External trigger
signals are synchronized with camera internal H signals so that approx. 3.583μs jitter to Exposure
Time delay would occur.
□ Trigger input during exposure time should be ignored. (Refer to the below A).

VCC-FC60FR19CL Rev.900-729-31-00
©2011 CIS Corporation. All rights reserved.
20
7.10. Pulse Width Trigger Shutter Mode
□ This is the mode to start exposure with external input trigger signals, and set the exposure time with
pulse width of the trigger signals.
□ Trigger operation is CLK Sync. HV-Sync Reset. The delay time (Exposure Time Delay) from
detecting trigger edge in the camera to starting exposure, and from detecting trigger end edge to
completing exposure is 370ns.
□ Pulse width is min. 10μs to approx. 2 frames. Functionally, there is no upper limitation, but noises
such as dark noises and shadings may be noticeable at long time exposure.
□Triggers can be accepted even when outputting video signals. However, trigger signals for
exposure to start the next video output prior to the completion of video transmission for the prior
video output signals can not be accepted.
If the edge part of trigger signals is overlapped with video outputting period, 1 line noise may
detected on the video output screen. To input trigger signals during video output period, set the
data of address 018 to 001 (Trigger input signal, camera internal H sync ON). External trigger
signals are synchronized with camera internal H signals so that approx. 3.583μs jitter to Exposure
Time delay would occur.
Effective Line :2048H
Effective Line
～ ～
Exposure Out
2048
1
Trigger IN
(Read Out Pulse)
LVAL Out
FVAL Out
Video Out
DVAL Out
～ ～
1
Effective Line
Trigger input ignore period
Exposure Time
Exposure Time Delay Exposure Time Delay
(A)
Trigger Input EN
Exposure Out
FVAL Out
～ ～
LVAL Out
1 Tap Base Configuration Mode 137
μs
2 Tap Base Configuration Mode 87
4 Tap Medium Configuration Mode 62
8 Tap Full Configuration Mode 49
LVAL Width Don' t Care
(3 H pe rio d)
μs
μs
μs
2048