CIS VCC-GC21U11PCL Quick start guide

VCC-GC21U11PCL Rev.900-763-30-00
En
g
lish
Camera link I/F
2M Resolution CMOS
B/W Power over Camera Link
VCC-GC21U11PCL
Product Specification
& Operational Manual
CIS Corporation
©2013 CIS Corporation. All rights reserved.

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
2
Table of Contents
PAGE
1. Scope of Application .............................................................................................................................................. 3
2. Handling Precautions ............................................................................................................................................... 3
3. Product Outline ..................................................................................................................................................... 5
4. Specification.......................................................................................................................................................... 5
4.1. General Specification .................................................................................................................................. 5
4.2. Camera Output Signal Specification ............................................................................................................. 7
4.3. CMOS Spectral Response (Representative Value) .......................................................................................... 8
4.4 Video Output Format .................................................................................................................................. 9
5. Function Settings................................................................................................................................................. 10
6. External Connector Pin Assignment....................................................................................................................... 13
6.1. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)........................................................................ 13
6.2. Power LED ............................................................................................................................................... 13
7. Timing Chart ....................................................................................................................................................... 14
7.1. Horizontal Synchronous Signals Timing (2Tap Base Configuration mode: 70fps).......................................... 14
7.2. Vertical Synchronous Signals Timing (2Tap Base Configuration Mode: 70fps) ............................................... 14
7.3. Horizontal Synchronous Signals Timing (4Tap Medium Configuration Mode: 140fps) *Initial Setting .............. 15
7.4. Vertical Synchronous Signals Timing (4Tap Medium Configuration Mode: 140fps)......................................... 15
7.5. Horizontal Synchronous Signals Timing (8Tap Full Configuration Mode: 280fps) ........................................... 16
7.6. Vertical Synchronous Signals Timing (8Tap Full Configuration Mode: 280fps) ............................................... 16
7.7. Fixed Trigger Shutter Mode ....................................................................................................................... 17
7.8. Pulse Width Trigger Shutter Mode.............................................................................................................. 18
8. Partial Scan Mode ................................................................................................................................................ 19
9. Remote Communication Function.......................................................................................................................... 21
10. Initial Settings ..................................................................................................................................................... 22
11. CMOS Optical Axis Accuracy ................................................................................................................................. 23
12. Dimensions ......................................................................................................................................................... 24
13. Cases for Indemnity (Limited Warranty) ................................................................................................................ 25
14. CMOS Pixel Defect ............................................................................................................................................... 25
15. Product Support .................................................................................................................................................. 25

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-GC21U11PCL, 2M resolution, Power over Camera Link B/W CMOS Camera.
All specifications contained herein are subject to change without prior notice. Reproduction in whole or in
part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not
apply to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
zDo not use or store the camera in the following extreme conditions:
¾Extremely dusty or humid places.
¾Extremely hot or cold places (operating temperature –5 to +4℃5)℃
¾Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
¾Places subject to fluorescent light reflections.
¾Places subject to unstable (flickering, etc.) lighting conditions.
¾Places subject to strong vibration.
zRemove dust or dirt on the surface of the lens with a blower.
zDo not apply excessive force or static electricity that could damage the camera.
zDo not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
zFollow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
z Confirm the mutual ground potential carefully and then connect the camera to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera.
z Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power
supply voltage may cause damages or malfunction of the camera.

VCC-GC21U11PCL Rev. 900-763-30-00
z The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
zThe rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoid noises like chattering when rising.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage
zPrecautions to observe when using partial mode.
At vertical partial scan mode, the smaller the value of read-out lines setting is set, the faster the
camera exposure output speed goes, and the more the power consumption is required at the same
time.
Power requirement of when the minimum read-out line is set with partial scan will be approx 1.5
times more than the one with full frame scan. Naturally, heat of the camera will be increased.
Especially when the read-out line is set in the range of 100 lines to 1 line, heat dissipation is
recommended to install the camera.
Installation recommended.
・ Install the camera to the place with ambient temperature under 40 ℃.
・ Install the camera to a metallic component.
©2013 CIS Corporation. All rights reserved.
4

VCC-GC21U11PCL Rev. 900-763-30-00
3. Product Outline
VCC-GC21U11PCL is a Power over Camera Link interfaced and 2M resolution industrial black and white
video camera module. 2M pixels CMOS sensor with diagonal length 12.775mm is utilized. Entire
pixels can be read out within 1/140s at Medium Configuration output.
Features
□ Global shutter CMOS sensor is utilized.
□ Camera Link Base, Medium, and Full Configuration are supported.
□ Fixed trigger shutter mode, pulse width trigger shutter mode are operable.
□ Full frame rates and video output format are as follows.
2Tap Base Configuration Mode 70fps 8bit/10bit
4Tap Medium Configuration Mode 140fps 8bit/10bit
8Tap Full Configuration Mode 280fps 8bit
Factory Setting: 4 Tap Medium 140fps 8bit
□ Free Software
¾CIS control panel software for evaluation purpose only is downloadable via our web.
4. Specification
4.1. General Specification
(1) Pickup Device
Device Type Diagonal Length 12.775mm, Global Shutter type, B/W CMOS
Effective pixel number 2048(H) x 1088(V)
Unit cell size 5.5μm(H) x 5.5μm(V)
Image Circle φ12.775mm
(2) Video Output Frequency
Pixel Clock 80 MHz
2Tap
Base Configuration Mode:
Horizontal frequency: 77.519 kHz Horizontal clock 1032 CLK
V
ertical frequency: 70.217 Hz Scanning lines 1104 H
4Tap
Medium Configuration Mode:
Horizontal frequency: 155.039 kHz Horizontal clock 516 CLK
V
ertical frequency: 140.434 Hz Scanning lines 1104 H
8Tap
Full Configuration Mode:
Horizontal frequency: 310.078 kHz Horizontal clock 258 CLK
V
ertical frequency: 280.867 Hz Scanning lines 1104 H
(3) Sync. System Internal Sync. System.
(4) Video Output 2Tap Base Configuration
4Tap Medium Configuration (Initial Setting)
8Tap Full Configuration
(5) Resolution 1088 TV Lines
(6) Output Format Sensor AD 10bit
Camera Link output 8bit / 10bit (Fixed to 8bit at Full Configuration mode.)
Monochrome output.
©2013 CIS Corporation. All rights reserved.
5

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
6
(7) Sensitivity F5.6 400lx (at Shutter speed 1/140s (OFF), Gain 0dB, and Medium Configuration mode)
(8) Minimum illumination F1.4 9.0lx (at Shutter speed 1/140s (OFF), Gain +12dB, and Medium Configuration mode)
(9) Dust or stains in optical
system
No dust or stain shall be detected on the testing screen with setting the camera aperture at F16.
(10) Power requirements PoCL
(11) Power consumption 2.7W (4Tap Medium Configuration mode, Full frame scan output): Initial setting.
4.0W (8Tap Full Configuration mode, Partial scan 100lines output)
(12) Dimensions Refer to overall dimension drawing. (H:29mm W:29mm D:45mm excluding projection)
(13) Weight Approx. 75g
(14) Lens mount C Mount * Refer to overall dimension drawing.
(15) Optical axis accuracy Refer to drawing for CMOS Optical Axis Accuracy.
(16) Gain variable range 0dB ～+12dB (Guaranteed range)
(17) Shutter speed variable
range
OFF ～1/50000s
(18) Trigger shutter mode Fixed Shutter Trigger Mode/ Pulse Width Shutter Trigger Mode
(19) Partial Scan Full Frame Scan ～ 1 line (1 line / step)
(20) Safety/Quality standards UL: Conform to UL Standard including materials and others.
CE:
EN55022:2010 Class A for Emission
EN61000-6-2:2005 for Immunity
RoHS: Conform to RoHS.
FCC:
T
o be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
(21) Durability
Vibration
Acceleration : 98m/s2(10G)
Frequency : 20～200 Hz
Direction : X,Y, and Z 3 directions
Test ing tim e : 120min for each direction
Shock No malfunction shall be occurred with 980m/s2(100G) for ±X,±Y, a n d ±Z,
6 directions. (without package)
(22) Operation Environment
Temp era ture Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temperature: -5℃～+45℃
※All the specifications specified in this manual is guaranteed under
performance guaranteed temperature.
※All the camera functions operate normally under operation guaranteed
temperature.
Humidity RH 20～80% with no condensation.
(23) Storage Environment Temp era ture -25℃～+60℃
Humidity RH 20～80% with no condensation.

VCC-GC21U11PCL Rev. 900-763-30-00
4.2. Camera Output Signal Specification
(1) Video output data Effective Video Output 2048(H) × 1088(V) At full frame scan mode
(2) Sync. Signal
output
LVAL Camera Link output (LVDS):
FVAL
DVAL
SP Optical Pulse
(3) Camera Control
Signals input
CC2・CC3・CC4 Camera Link Input (LVDS)
(4) Trigger Input
Polarity Positive/Negative Selectable Polarity is selectable with
Address 011
Pulse Width
1HD (min.) ～ Approx. 2 frames
・2Tap Base Configuration mode : 1HD (12.9us)
・4Tap Medium Configuration mode : 1HD (6.45us)
・8Tap Full Configuration mode : 1HD (3.225us)
Functionally, no upper limitation is set but noises such as dark
noises and shadings might be noticeable at long time exposure.
Trigger Input ：CC1 Camera Link input (LVDS)
(5) Serial
Communication
SerTC (Serial to Camera) Camera Link input (LVDS）
SerTFG (Serial to Frame Grabber) Camera Link output (LVDS)
(6) Video Signals
White Clip Level At Digital 10bit
At Digital 8bit
: 3FFh
: FFh
Setup Level At Digital 10bit
At Digital 8bit
: under 004h
: under 01h
(Condition: Gain 0dB)
Dark Shading At Digital 10bit
At Digital 8bit
: Both horizontal and vertical
should be under ±00Fh.
: Both horizontal and vertical
should be under 03h.
(Condition: Gain 0dB)
※ 2 seconds shall be waited after turning on power to get the camera operate properly.
©2013 CIS Corporation. All rights reserved.
7

VCC-GC21U11PCL Rev. 900-763-30-00
4.3. CMOS Spectral Response (Representative Value)
* Lens characteristics and luminous source characteristics are not considered.
©2013 CIS Corporation. All rights reserved.
8

VCC-GC21U11PCL Rev. 900-763-30-00
4.4 Video Output Format
(1) 2Tap Base Configuration Mode : 38fps
©2013 CIS Corporation. All rights reserved.
9
(2) 4Tap Medium Configuration Mode : 75fps (Initial Setting)
(3) 8Tap Full Configuration Mode : 150fps
・・・D D
～
～
～
～
1088 Line
2048pixel
1 2
D DD D ・・・
～
～～ ～
1088 Line
2048pixel
1234
2048pixel
DDDDDDDD・・・
～
～～ ～
1088 Line
12345678

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
10
5. Function Settings
(Camera functions can be set with serial communications.)
Function Address Data
Gain 001 0: 0 dB : Fixed Gain
1: + 3 dB : Fixed Gain
2: + 6 dB : Fixed Gain
3: + 12 dB : Fixed Gain
4: Manual Gain: over 0～+12dB (Refer to Address 032 and 033.)
Shutter 002 2Tap Mode 4Tap Mode 8Tap Mode
0: 1/70s(OFF) 1/140s(OFF) 1/280s(OFF)
1: 1/140s 1/140s(OFF) 1/280s(OFF)
2: 1/280s 1/280s 1/280s(OFF)
3: 1/350s 1/350s 1/350s
4: 1/500s 1/500s 1/500s
5: 1/750s 1/750s 1/750s
6: 1/1000s 1/1000s 1/1000s
7: 1/2500s 1/2500s 1/2500s
8: 1/5000s 1/5000s 1/5000s
9: 1/7500s 1/7500s 1/7500s
10: 1/10000s 1/10000s 1/10000s
11: 1/15000s 1/15000s 1/15000s
12: 1/20000s 1/20000s 1/20000s
13: 1/30000s 1/30000s 1/30000s
14: 1/30000s 1/40000s 1/40000s
15: 1/30000s 1/40000s 1/50000s
16: Manual Shutter (Refer to Address 036 and 037.)
Trigger Shutter Mode 004 0: Normal Shutter Mode (Trigger OFF)
1: Fixed Trigger Shutter Mode (Shutter speed can be set with address 002.)
2: Pulse Width Trigger Shutter Mode
(Shutter speed can be set with trigger pulse width.)
Trigger Polarity 011 0: Positive
1: Negative
Output Data Selection 013 0: 8bit Output
1: 10bit output (10bit cannot be output at 8Tap Full Configuration mode.)
Partial Scan Mode 015 0: Full Frame Scan Mode
1: Partial Scan Mode
Output image flip vertical 021 0: Normal
1: Flip Vertical
Gain CC Control ON/OFF 023 0: OFF
1: ON (Gain and WB can be controlled via CC2, CC3, and CC4.)

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
11
Function Address Data
Table Selection for Gain CC
Control
024 0～7: CC2 CC3 CC4
0: L L L
1: H L L
2: L H L
3: H H L
4: L L H
5: H L H
6: L H H
7: H H H
T
able Read/Write for Gain
CC Control
025 0: Nop
1: Table Read
2: Table Write
Manual Gain (Address 032&033) is written in to the table specified with
Address 024.
3: Clear Table
Baud Rate 030 0: 9600bps
1: 19200bps
2: 38400bps
3: 57600bps
4: 115200bps
Camera Mode 031 0: 8Tap Full Configuration Mode (280fps)
1: 4Tap Medium Configuration Mode (140fps)
2: 2Tap Base Configuration Mode (70fps)
Manual Gain 032&033 0～767: 0:0dB ～767:+12dB
Manual Shutter 036&037 0～1087:
2Tap mode: Shutter Speed = 16.641us + (1088 - (036&037))×12.9us
Min. value 0: 14.052ms(1/70s), Max. value 1087: 29.541us(1/30000s)
4Tap mode: Shutter Speed = 16.641us + (1088 - (036&037))×6.45us
Min. value 0: 7.034ms(1/140s), Max. value 1087:23.091us(1/40000s)
8Tap mode: Shutter Speed = 16.641us + (1088- (036&037))×3.225us
Min. value 0: 3.525ms(1/280s), Max. value 1087: 19.866us (1/50000s)
※Set the data of the address 002 to 016.
Cursor Indication ON/OFF 058 0: OFF
1: ON
Cursor X Address 061&060 0～2047:
Cursor Y Address 063&062 0～1087:
Partial scan start position 1 064&065 0～1087:
Partial scan start position 2 066&067 0～1087:
Partial scan start position 3 068&069 0～1087:
Partial scan start position 4 070&071 0～1087:
Partial scan start position 5 072&073 0～1087:
Partial scan start position 6 074&075 0～1087:
Partial scan start position 7 076&077 0～1087:
Partial scan start position 8 078&079 0～1087:
※Set the data of the address 015 to 001.

VCC-GC21U11PCL Rev. 900-763-30-00
©2013 CIS Corporation. All rights reserved.
12
Function Address Data
Partial scan effective line numbers 1 080&081 1～1088: Set 0 when not in use.
Partial scan effective line numbers 2 082&083 1～1088: Set 0 when not in use.
Partial scan effective line numbers 3 084&085 1～1088: Set 0 when not in use.
Partial scan effective line numbers 4 086&087 1～1088: Set 0 when not in use.
Partial scan effective line numbers 5 088&089 1～1088: Set 0 when not in use.
Partial scan effective line numbers 6 090&091 1～1088: Set 0 when not in use.
Partial scan effective line numbers 7 092&093 1～1088: Set 0 when not in use.
Partial scan effective line numbers 8 094&095 1～1088: Set 0 when not in use.
※Set the data of the address 015 to 001.
Initial Settings 126 Input 083 to set the camera back to the initial settings.
Data Save 127 Input 083 to save the data to EEP-ROM.
※ The data set with 2 Byte shall be set with High Byte (even address) first, then set with Low Byte (odd
address). The camera rewrites the internal resister when receiving Low Byte.

VCC-GC21U11PCL Rev. 900-763-30-00
6. External Connector Pin Assignment
6.1. Camera Link Connector 12226-1100-00PL (SUMITOMO 3M)
Connector(CN1) Connector(CN2)
Pin
No.
Pin
No.
Pin
No.
Pin
No.
1 GND/+12V(PoCL) 14 GND 1 NA 14 GND
2 X0- 15 X0+ 2 Y0- 15 Y0+
3 X1- 16 X1+ 3 Y1- 16 Y1+
4 X2- 17 X2+ 4 Y2- 17 Y2+
5 Xclk- 18 Xclk+ 5 Yclk- 18 Yclk+
6 X3- 19 X3+ 6 Y3- 19 Y3+
7 SerTC+ 20 SerTC- 7 100Ω20 Terminated
8 SerTFG- 21 SerTFG+ 8 Z0- 21 Z0+
9 CC1- (Trigger IN -) 22 CC1+ (Trigger IN +) 9 Z1- 22 Z1+
10 CC2+ 23 CC2- 10 Z2- 23 Z2+
11 CC3- 24 CC3+ 11 Zclk- 24 Zclk+
12 CC4+ 25 CC4- 12 Z3- 25 Z3+
13 GND 26 GND/+12V(PoCL) 13 GND 26 NA
6.2. Power LED
(1) Power LED is lit when power is supplied to the camera via the frame grabber board.
※Power to the camera shall be supplied only via CN1 of the Base connector side. CN1 power line of the Medium or Full
configuration connector side shall be kept open. Do not plug and unplug the camera link cables since it may cause the
camera malfunction.
©2013 CIS Corporation. All rights reserved.
13

VCC-GC21U11PCL Rev. 900-763-30-00
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing (2Tap Base Configuration mode: 70fps)
7.2. Vertical Synchronous Signals Timing (2Tap Base Configuration Mode: 70fps)
©2013 CIS Corporation. All rights reserved.
14
FVAL Out
1Frame = 1104H(14.242ms)
Effective Line : 1088H
Effective Line
DVAL Out
～ ～
LVAL Out
～ ～
Effective Line
～ ～～
～
V Blanking : 16H
(Read Out Pulse)
Exposure Time( Address (036&037))
SP Out(Exposure Out)
1
0
8
8
1
0
8
8
11
Video Out
～ ～ ～ ～
10
H
1H = 12.9us

VCC-GC21U11PCL Rev. 900-763-30-00
7.3. Horizontal Synchronous Signals Timing (4Tap Medium Configuration Mode: 140fps) *Initial Setting
7.4. Vertical Synchronous Signals Timing (4Tap Medium Configuration Mode: 140fps)
©2013 CIS Corporation. All rights reserved.
15
FVAL Out
1Frame = 1104H(7.121ms)
Effective Line : 1088H
Effective Line
DVAL Out
～ ～
LVAL Out
～ ～
Effective Line
～ ～～
～
V Blanking : 16H
(Read Out Pulse)
Exposure Time( Address (036&037))
SP Out(Exposure Out)
1
0
8
8
1
0
8
8
11
Video Out
～ ～ ～ ～
1H = 6.45us
7
H

VCC-GC21U11PCL Rev. 900-763-30-00
7.5. Horizontal Synchronous Signals Timing (8Tap Full Configuration Mode: 280fps)
7.6. Vertical Synchronous Signals Timing (8Tap Full Configuration Mode: 280fps)
©2013 CIS Corporation. All rights reserved.
16
FVAL Out
1Frame = 1104H(3.560ms)
Effective Line
DVAL Out
～ ～
Effective Line : 1088H
LVAL Out
～ ～
Effective Line
～ ～
Video Out
～ ～
V Blanking : 16H
(Read Out Pulse)
Exposure Time( Address (036&037))
SP Out(Exposure Out)
1
0
8
8
1
0
8
8
11
～ ～ ～ ～
1
H
1H = 3.225us

VCC-GC21U11PCL Rev. 900-763-30-00
7.7. Fixed Trigger Shutter Mode
□ This is the mode to start exposure with external input trigger signals, and set the exposure time with
serial commands.
□ Trigger operation is H Sync. V-Sync Reset. The delay time (Exposure Time Delay) from
detecting trigger edge in the camera to starting exposure is max. 1HD.
□ Triggers can be accepted even when outputting video signals. However, trigger signals for
exposure to start the next video output prior to the completion of video transmission for the prior
video output signals cannot be accepted.
□ If the next trigger is input prior to the completion of video transmission for the prior video output
signals, the image may be impacted.
□ Trigger input during exposure time should be ignored. (Refer to the below A).
Effective Line : 1088H
Effective Line
～ ～
SP Out
(Exposure Out)
1
0
8
8
1
TRIG IN
(Read Out Pulse)
LVAL Out
FVAL Out
Video Out
DVAL Out
～ ～
1
0
8
8
1
Effective Line
Exposure Time
(Trigger input ignore period)
Exposure Time Delay
(A)
TRIG Input EN
TRIG IN
SP Out
(Exposure Out)
2Tap Base Configuration Mode max 12.9us
4Tap Medium Configuration Mode
8Tap Full Configuration Mode
max 6.45us
max 3.225us
©2013 CIS Corporation. All rights reserved.
17

VCC-GC21U11PCL Rev. 900-763-30-00
7.8. Pulse Width Trigger Shutter Mode
□ This is the mode to start exposure with external input trigger signals, and set the exposure time with
pulse width of the trigger signals.
□ Trigger operation is H Sync. V-Sync Reset. The delay time (Exposure Time Delay) from
detecting trigger edge in the camera to starting exposure, and from detecting trigger end edge to
completing exposure is max. 1HD.
□ Pulse width is min. 1HD to approx. 2 frames. Functionally, there is no upper limitation, but noises
such as dark noises and shadings may be noticeable at long time exposure.
□Triggers can be accepted even when outputting video signals. However, trigger signals for
exposure to start the next video output prior to the completion of video transmission for the prior
video output signals cannot be accepted.
□ If the next trigger is input prior to the completion of video transmission for the prior video output
signals, the image may be impacted.
Effective Line : 1088H
Effective Line
～ ～
SP Out
ure Out)
1
0
8
8
1
(Expos
TRIG IN
(Read Out Pulse)
LVAL Out
VAL OutF
Video Out
DVAL Out
～ ～
1
0
8
8
1
Effective Line
Exposure Time
(Trigger input ignore period)
Exposure Time Delay Exposure Time Delay
(A)
TRIG IN
SP Out
(Exposure Out)
2Tap Base Configuration Mode max 12.9us
4Tap Medium Configuration Mode
8Tap Full Configuration Mode
max 6.45us
max 3.225us
©2013 CIS Corporation. All rights reserved.
18

VCC-GC21U11PCL Rev. 900-763-30-00
8. Partial Scan Mode
□ Maximum 8 partial areas can be set by serial commands.
Example ： 3 partial areas to be set.
Partial Scan Setting
©2013 CIS Corporation. All rights reserved.
19
①： V Blanking Line Number
②: Partial Area 1
③： Partial Area 2
④： Partial Area 3
⑤： Total Frame Line Number
FVA
L
LVA
L
①
⑤
②③ ④
V
ideo Out
Partial scan start position 1
(
A
ddress 064 & 065)
④
Partial scan start position 3
(
A
ddress 068 & 069)
③
Partial scan effective lines 2
(Address 082&083)
Partial scan start position 2
(
A
ddress 066 & 067)
②
Partial scan effective lines 3
(Address 084&085)
0
2047
Partial scan effective lines 1
(Address 080&081)
④
②
Partial scan effective lines 1
(Address 080&081)
Data sequence of output video
③
Partial scan effective lines 2
(Address 082&083)
Partial scan effective lines 3
(Address 084&085)

VCC-GC21U11PCL Rev. 900-763-30-00
□ When setting several partial scan areas, please set the start position and effective lines trying not to
overlap the areas.
□ When setting several areas, please set the areas in the numerical order of starting position.
□ Entire frame line numbers = V blanking line numbers (16H fixed) ＋
Partial effective lines 1 + Partial effective lines 2 + ・・・ + Partial effective lines 8
Note that “Sum total of partial effective line numbers (except V blanking lines) ≦1088” should be met.
□ Frame rate = 1 / (Entire frame line numbers x Time for 1 line)
Time for 1 line
Camera Mode Time for 1 Line
2Tap Base Configuration Mode 12.9us
4Tap Medium Configuration Mode 6.45us
8Tap Full Configuration Mode 3.225us
□ Setting Example
Effective
Lines
Entire
Frame Lines
Frame Rate (Entire frame lines)
2Tap Mode 4Tap Mode 8Tap Mode
1(Min) 1 H 17H 4560fps 9120fps 18240fps
・・
Vertical:VGA
equivalent
480 H 496H 156fps 313fps 625fps
・・
Vertical:XGA
equivalent
768 H 784H 99fps 198fps 396fps
・・
Vertical:SXGA
equivalent
1024 H 1040H 75fps 149fps 298fps
・・
1104
(Max:Full Frame)
1104 H 1088H 70fps 140fps 280fps
□ Line numbers at partial scan setting can be set from 1 line. However, consumption current will
increase several hundreds mA more so that the margin of camera power capacity shall be considered.
©2013 CIS Corporation. All rights reserved.
20