CIS VISION:elite VCC-GM60FV11CL Quick start guide

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
125M Ultra High Resolution
B/W Camera Link
VCC-GM60FV11CL
Product Specification
& Operational Manual
CIS Corporation
English

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
2
Table of Contents
PAGE
1. Scope of Application ···································································································· 3
2. Handling Precautions ··································································································· 3
3. Product Outline·········································································································· 5
4. Specification·············································································································· 6
4.1. General Specification ·························································································· 6
4.2. Camera Output Signal Specification ········································································ 8
4.3. CCD Spectral Response (Representative Value) ·························································· 9
4.4. Video Output Format ·························································································· 9
5. Function Settings ······································································································· 10
6. External Connector Pin Assignment ················································································· 12
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) equivalent····································· 12
6.2. 26 pins Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M) ································ 12
7. Timing Chart ············································································································ 13
7.1. Horizontal Synchronous Signals Timing ··································································· 13
7.2. Full Frame Scan Mode························································································ 13
7.3. Fixed Trigger Shutter Mode ················································································· 14
7.4. Pulse Width Trigger Shutter Mode ········································································· 15
8. Partial Scan Mode Details ····························································································· 16
9. Remote Communication Function ··················································································· 17
10. Initial Settings··········································································································· 18
11. SOPT Control ··········································································································· 19
11.1. Software Trigger Control Sequence········································································ 19
11.2. External Trigger Control Sequence········································································· 20
11.3. To operate SOPT with software trigger (45M Mode)···················································· 21
11.4. To opererate SPOT with external trigger signals (45M Mode) ········································ 21
12. Image Synthesis ········································································································ 22
13. CCD Optical Axis Accuracy ···························································································· 24
14. Dimensions ·············································································································· 25
15. Cases for Indemnity (Limited Warranty) ··········································································· 26
16. CCD Pixel Defect········································································································ 26
17. Product Support ········································································································ 26

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
3
1. Scope of Application
This is to describe VCC-GM60FV11CL, Ultra High Resolution Camera Link B/W CCD Camera.
All specifications contained herein are subject to change without prior notice. Reproduction in whole or in
part is prohibited.
2. Handling Precautions
The camera must not be used for any nuclear equipments or aerospace equipments with which mechanical
failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not
apply to damages or defects caused by irregular and/or abnormal use of the product.
Please observe all warnings and cautions stated below.
Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.
No vibration shall be caused to the camera or the object to shoot while pixel shifting is in operation.
If images are captured under vibration, the PC synthesized image will be blurred. We recommend
you to install our camera into your actual application systems to try and evaluate it.
Do not use or store the camera in the following extreme conditions:
Extremely dusty or humid places.
Extremely hot or cold places (operating temperature –5℃to +40℃)
Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
Places subject to fluorescent light reflections.
Places subject to unstable (flickering, etc.) lighting conditions.
Places subject to strong vibration.
Remove dust or dirt on the surface of the lens with a blower.
Do not apply excessive force or static electricity that could damage the camera.
Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera
is not in use, put the lens cap on.
Follow the instructions in Chapter 6, “External connector pin assignment” for connecting the camera.
Improper connection may cause damages not only to the camera but also to the connected devices.
Confirm the mutual ground potential carefully and then connect the camera to monitors or
computers. AC leaks from the connected devices may cause damages or destroy the camera.
Do not apply excessive voltage. (Use only the specified voltage.) Unstable or improper power
supply voltage may cause damages or malfunction of the camera.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
4
The voltage ripple of camera power DC +12V±10% shall be within ±50mV. Improper power
supply voltage may cause noises on the video signals.
The rising time of camera power supply voltage shall be less than +10V, Max 60ms. Please
avoide noises like chattering when rising.
2ch output CCD, separated into right and left, is utilized for VCC-G60FV11CL. Image signals for
right half screen and left half screen are output via each independent circuit.
Therefore, differences between right screen and left screen could be seen depending on the usage
conditions (shooting conditions /temeperature conditions and so on).
CIS trys its best to adjust this differences but please be noted it would not be perfect.
10 4020 30 50
10
11
12
[V]
Voltage Rising Time [ms]
9
8
7
60 70
Power Supply Voltage

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
5
3. Product Outline
VCC-GM60FV11CL is a Camera Link interfaced, ultra high-resolution industrial black and white video
camera module. Pixel shifting technology with piezo-actuator, 45M pixels and 125M pixels ultra high
resolutions are realized. Image synthesis processing shall be done by PC software.
In this Specification, we describe pixel shifting technology as “SOPT: Spatial Offsetting Pickup
Technique”.
Features
□Frame rates to read out entire pixels at full frame scan mode are as follows.
SOPT OFF (Basic Mode): 5M Pixels: approx. 15fps (66.7ms)
SOPT ON (45M Mode): 45M Pixels: approx. 1.43fps (700ms)
SOPT ON (125M Mode): 125M Pixels: approx. 0.516fps (1.94s)
※When SOPT is ON, partial scan mode and pulse width trigger mode can not be used.
□CLK Sync, V-Sync reset Trigger
□At SPOT OFF, triggers can be input even when outputting images.
□8bit/10bit output are selectable.
□Free Software
Sample software of image synthesis for DALSA Corporation SaperaLT.
Sample software of image synthesis for EURESYS Inc. Multicam Studio.
Sample software of image synthesis for Matrox Electronic Systems Ltd. MIL.
Sample software of image synthesis for AVAL DATA Corporation, Acap Lib2.
Sample software of image synthesis for Micro Technica Board Library/SDK.
※Please ask us for the details on image synthesis software.
□Verified Frame Grabber Board
TB-6S-LX150T-GB-R (Tokyo Electron Device LTD).
※Please ask Tokyo Electron Device Ltd for the details on the frame grabber board.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
6
4. Specification
4.1.General Specification
Item
Specification
(1) Pickup Device
Device type
2/3type interline transfer B/W CCD SONY ICX625ALA
Effective pixel
number
2456(H) × 2058(V)
Unit cell size
3.45μm(H) × 3.45μm(V)
Chip size
9.93mm(H) × 8.70mm(V)
(2) Sync. System
Internal Sync. System.
(3) Video Output
Camera Link (Base Configuration)
(4) SOPT Mode
SOPTOFF (5M Basic Mode)
Pixel clock
60 MHz
Horizontal frequency
31.185 KHz
Pixel CLK
1924 CLK
Vertical frequency
at full frame sacn mode
15.000 Hz
Scanning Lines
2079 H
Output pixels
Horizontal
2448 pixel
Vertical
2058 pixel
TTL pixels
Approx. 5 Mega pixels
Resolutions
2058TV lines
SOPT (45M Mode)
Frame rate of the synthetic image
(When long term exposure mode is OFF)
Approx. 1.43fps
Pixel numbers of the
synthetic image
Horizontal
7344 pixel
Vertical
6174 pixel
TTL pixels
Approx. 45 Mega pixels
SOPT (125M Mode)
Frame rate of the synthetic image
(When long term exposure mode is OFF)
Approx. 0.516fps
Pixel numbers of the
synthetic image
Horizontal
12240 pixel
Vertical
10290 pixel
TTL pixels
Approx. 125 Mega pixels
(5) Resolving power
8bit / 10bit
(6) Sensitivity
F5.6 400lx (Shutter Speed 1/15s, Gain 0dB)
(7) Minimum illumination
F1.4 1lx (Shutter Speed 1/15s, Gain Max(+12dB)
(8) Dust or stains in
optical system
No dust or stain shall be detected on the testing screen with setting the camera
aperture at F16.
(9) Power requirements
DC+12V±10%
(10) Power consumption
4.8W (At DC +12V IN, normal mode, and full frame scan mode)
5.5W (At DC +12V IN, normal mode, and partial scan mode)
(11) Dimensions
Refer to overall dimension drawing.
H:55mm W:55mm D:84.5mm (excluding projection.)
(12) Mass
Approx. 510g
(13) Lens mount
C Mount (Refer to overall dimension drawing)

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
7
Item
Specification
(14) Optical axis accuracy
Refer to drawing for CCD Optical Axis Accuracy.
(15) Gain variable range
0～+12dB (Analog Gain over 0dB～+6dB, Digital Gain 0dB～+6dB)
(16) Shutter speed variable
range
1/15s (OFF) ～1/30000s
(17) Trigger shutter mode
・Fixed Trigger Shutter Mode
・Pulse Width Trigger Shutter Mode (Only when SOPT OFF)
(18) Safety/Quality
standards
・UL: Conform to UL Standard including materials and others.
・RoHS: Conform to RoHS
・CE: Conform to EN55022:2006 Class A for Emission
Conform to EN61000-6-2:2005 for Immunity
・FCC: To be applied to FCC Class A digital Device
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
(19) Durability
Vibration
Acceleration
: 19.61m/s2 (2.0G)
Frequency
: 20～200 Hz (Frequency varies every 5 minutes.
It shall be tested 120 minutes each for 3 directions.
Direction
: X,Y,Z 3 directions
Testing time
: 15 min for each direction
Shock
No malfunction shall be occurred with 490m/s2(50G) for ±X, ±
Y, and ±Z, 6 directions. (without package)
(20) Operation
environment
Temperature
Performance guaranteed temperature: 0℃～+40℃
Camera operation guaranteed temeprature: -5℃～+45℃
※All the specifications specified in this manual is guaranteed
under performance guaranteed temperature.
※All the camera functions operate normally under operation
guaranteed temperature
Humidity
RH 20～80% with no condensation.
(21) Storage Environment
Temperature
-25℃～+60℃
Humidity
RH 20～80% with no condensation.
※In this Specification, we describe pixel shifting technology as “SOPT: Spatial Offsetting Pickup Technique”.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
8
4.2.Camera Output Signal Specification
Item
Specification
(1) Video output data
Video Output
2456(H) × 2058(V)
At full frame scan mode
60MHz 2Tap output
(2) Sync. Signal I/O
LVAL output
LVTTL(3.3V)
12pins Circular Connector
FVAL output
LVTTL(3.3V)
DVAL output
LVTTL(3.3V)
Exposure
LVTTL(3.3V)
(3) Trigger Input
Polarity
Positive/Negative Selectable
Pulse Width
Over 2H (min) ～Under 4158H (max)
Hardware
Trigger Input
LVTTL(5.0V Tolerant)
HR10-10R-12PA
Software Trigger
Input
Serial Communications
(4) Video Signals
White Clip Level
At Digital 8bit
: FFh
Setup Level
At Digital 8bit
: 08h±04h (Conditions: Gain 0dB)
Dark Shading
At Digital 8bit
: Under 08h for both horizontal and vertical.
(Conditions: Gain 0dB)
Leval differences
between
right and left
At Digital 8bit
: Under 03h (Conditions: Gain 0dB)
※2 secounds shall be waited after turning on power to get proper camera operation.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
9
4.3. CCD Spectral Response (Representative Value)
※Lens charcteristics and luminous source charcteristics are not considered.
4.4. Video Output Format
・2-Taps Output
・Area of interest Width : 2448 Height : 2058 Offset X : 0 Offset Y : 12

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
10
5. Function Settings
(Camera functions can be set with serial communications.)
Function
Address
Data
Gain
001
0:
0
dB : Analog Fixed Gain
1:
+
3
dB : Analog Fixed Gain
2:
+
6
dB : Analog Fixed Gain
3:
+
12
dB : Analog Gain(+6dB) + Digital Gain(+6dB)
4:
Manual Gain (Refer to Address 005&006, 007&008, 126&127,
and 128&129.)
Shutter
* At SOPT mode, long term
exposure mode settings are
given priority. (Refer to
address 098&099)
002
0:
1/15s(OFF)
1:
1/30s
2:
1/60s
3:
1/90s
4:
1/120s
5:
1/150s
6:
1/200s
7:
1/250s
8:
1/500s
9:
1/750s
10:
1/1000s
11:
1/2000s
12:
1/5000s
13:
1/10000s
14:
1/15000s
15:
1/30000s (1/15000s at SOPT mode.)
16:
Manual Shutter (Refer to Address 009 and 010)
Trigger Shutter Mode
004
0:
Normal Shutter Mode (Trigger Mode Off)
1:
Fixed Trigger Shutter Mode
(Shutter speed can be set with address 002.)
2:
Pulse Width Trigger Shutter Mode
(Shutter speed can be set with trigger pulse width.)
Manual Analog Gain
(Right)
005&006
0～512:
0:0dB～512:+12dB and over (Log Linear)
※Set the data of address 001 to 004.
Manual Analog Gain (Left)
007&008
0～512:
0:0dB～512:+12dB and over (Log Linear)
※Set the data of address 001 to 004.
Manual Shutter Control
009&010
0～2078:
1/15s(OFF)～1/36058s
※Set the data of address 002 to 016.
Address 009 MSB and address 010 LSB makes total 16bit.
Shutter Speed =(2078 - (009&010))×32.07μs+27.73μs
Max Data = 2078
Trigger Polarity
011
0:
Positive Input
1:
Negative Input
Trigger Input
012
0:
Camera Link
1:
12pins Circular Connector
Output Data Select
013
0:
8bit Output Data
1:
10bit Output Data

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
11
Function
Address
Data
Gamma Mode
014
0:
Gamma OFF(1.0)
1:
Gamma On
(Option)
Partial Scan Mode
015
0:
Full Frame Scan Mode
1:
Partial Scan Mode
Partial Scan Start Position
016&017
0～685:
※Set the data of address 015 to 001.
Address 016 MSB and address 017 LSB makes total 16bit.
Start Position:3 H/step Min Data:0(0 H) / Max Data:685(2055 H)
Start Position (016&017) + Effective Line (019&020) should be <= 685.
Partial Scan Effective Line
019&020
0～684:
※Set the data of address 015 to 001.
Address 019 MSB and address 020 LSB makes total 16bit.
Effective Line:3 H/step Min Data:0(3 H) / Max Data:685(2058 H)
Start Position (016&017) + Effective Line(019&020) should be <= 685.
Partial Scan Total Line
021&022
0～2078:
Read Only
Total line number at Partial Scan Mode or Full Frame Scan Mode minus 1
is to be set
Baud Rate
030
0:
9600bps
1:
19200bps
2:
38400bps
3:
57600bps
4:
115200bps
Frame ID ON/OFF
060
0:
OFF
1:
ON
Software Trigger
061
0:
Software Trigger On
Light access is recognized as a trigger. There is no need to prepare a
pulse trigger with data values.
SOPT Mode
062
0:
45M Mode
1:
125M Mode
SOPT Standby
063
0:
Standby OFF
1:
External Trigger Standby
2:
Software Trigger Standby
SOPT Long Term Exposure
Mode
098&099
2079:
OFF: Operates at fixed trigger shutter setting.
2080 ～
64449:
ON:
Exposure Time=(098&099) x 32.07μs + 27.73μs
Internal Trigger Cycle=((098&099) + 321) x 32.07μs + 27.73μs
Manual Digital Gain
(Right)
126&127
256 ～
512:
256:×1(0dB)～512:×2(+6dB)
※Set the data of address 001 to 004.
Manual Digital Gain (Left)
128&129
256 ～
512:
256:×1(0dB)～512:×2(+6dB)
※Set the data of address 001 to 004.
Data Save
255
Input 083 or 053 to save the data in EEP-ROM.
※In this Specification, we describe pixel shifting technology as “SOPT: Spatial Offsetting Pickup Technique”.
※The data set with 2 Byte shall be set with High Byte first, then set with Low Byte. The camera rewrites
the internal resister when receiving Low Byte.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
12
1
14
13
26
6. External Connector Pin Assignment
6.1. 12 pins Circular Connector HR10-10R-12PA (HIROSE) equivalent
6.2. 26 pins Camera Link Connector 12226-1100-00 PL (SUMITOMO 3M)
Pin No.
1
GND
2
POWER IN DC +12V
3
GND
4
NA
5
GND
6
LVAL/OUT
7
FVAL/OUT
8
GND
9
Exposure Out
10
DVAL/OUT
11
Trigger IN
12
GND
Pin No.
Pin No.
名称
1
GND
14
GND
2
X0-
15
X0+
3
X1-
16
X1+
4
X2-
17
X2+
5
XCLK-
18
XCLK+
6
X3-
19
X3+
7
SerTC+
20
SerTC-
8
SerTFG-
21
SerTFG+
9
CC1- (Trigger IN -)
22
CC1+ (Trigger IN +)
10
NA (CC2+)
23
NA (CC2-)
11
NA (CC3-)
24
NA (CC3+)
12
NA (CC4+)
25
NA (CC4-)
13
GND
26
GND

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
13
LVAL Output
Video Output
DVAL Output
FVAL Output
1 2 3 4 5 6 7 8 9 1020762075 11 12 21 23 24
(CCD Read Out Signal)
9 H
21 H2058 H
12 H
Total = 2079H
207920782077
2058 H
22
LVAL Output
700 CLK
Video Output
DVAL Output
700 CLK
FVAL Output
1924 CLK
1224 CLK
CLK = 60MHz
2Tap Output
7. Timing Chart
7.1. Horizontal Synchronous Signals Timing
7.2. Full Frame Scan Mode

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
14
LVAL Output
Video Output
FVAL Output
DVAL Output
12H
TTL IN(a)
(CCD Read
Out Signal)
1 9
22 2079
2058H
2070H
(Trigger Input)
Trigger IN
(Sub Pulse)
(CCD Read Out Signal)
Exposure Output
a
1203
CLK
81
CLK
a
b
21.40μs
CLK60MHz
nHD × 32.07μs+27.73μs
Delay(Fixed)
Exposure Timeb
7.3. Fixed Trigger Shutter Mode
□Trigger operation is CLK Sync. V-Sync Reset. The delay time from detecting trigger edge in the camera
to starting exposure is 21.40μs.
□Triggers can be accepted even when outputting video signals. However, shutter timing to start the next
video output prior to the completion of video transmission for the prior video output signals can not be
accepted. Trigger input while outputting video signals should be synchronized with the down edge of
camera LVAL output.
□Trigger input during exposure time should be ignored. (Refer to the below G.).
(
E
)
（Ｂ）
（Ｂ）
(
F
)
Trigger Invalid
(
E
)
（Ｆ）
(
F
)
(
G
)
X
Standard Trigger Mode
Video Output
Trigger IN
DVAL Output
Exposure Output
Exposure Time
(
Register Set Value
)
Exposure Time
(
Register Set Value
)
(
Exposure Time
)
X

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
15
LVAL Output
Video Output
FVAL Output
DVAL Output
12H
Trigger IN
(CCD Read
Out Signal)
1 9
22 2079
2058H
2070H
TTL IN(a)
(Trigger Input)
b
1216
CLK
a
b
532
CLK
Delay(Fixed)
21.40μs
CLK60MHz
29.13μs
Exposure Output
Exposure Time
(Sub Pulse)
(CCD Read Out Signal)
a
1203
CLK
81
CLK
Delay(Fixed)
7.4. Pulse Width Trigger Shutter Mode
□Trigger operation is CLK Sync. V-Sync Reset. The delay time from detecting trigger edge in the camera
to starting exposure is 21.40μs. The delay time from detecting trigger edge to complete exposure is
29.13μs.
□Triggers can be accepted even when outputting video signals. However, shutter timing to start the next
video output prior to the completion of video transmission for the prior video output signals can not be
accepted. (Refer to the below C). Trigger input while outputting video signals should be
synchronized with the down edge of camera LVAL output.
(
A
)
(
A
)
(
B
)
（Ｂ）
(
B
)
(
C
)
（Ｂ）
(
D
)
(
D
)
Trigger Invalid
Pulse Width Trigger Mode
X
Video Output
Trigger IN
DVAL Output
Exposure Output
Exposure Time
(
Pulse Width
)
Exposure Time
(
Pulse Width
)
Exposure Time
(
Pulse Width
)
(
Video Output
(
C
))
X
(
Exposure Time
)

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
16
FVAL Output
(Normal Scan)
9 H
Video Output
(Normal Scan)
2079 H
VIDEO Output
(Partial Scan)
FVAL Output
(Partial Scan)
9 H
12 H
Total Line(Address 021&022) + 1H
2058 H
Y Offset
12H + Starting Position
(Address016&017)
Effective Line
(Address 019&020)×3+3H
High Speed
Transmit Term
High Speed
Transmit Term
8. Partial Scan Mode Details
At Partial Scan Mode, both starting position and width of capturing can be set by 3H.
Reading out position register (Address 016&017) : 0(0 H) ~685(2055 H) 3 H/step
Effective line register (Address 019&020) : 0(3 H) ~685(2058 H) 3 H/step
Total line resister (Address 021&022) : 706 H + (Effective line register × 2) + 2 (Read Only)
(Note)Reading out position and effective lines should meet the following conditions.
Reading out position register + Effective line register =< 685
If the above conditions are not met, the value, 685 –reading out position register
is to be set to the effective lines register.
<Setting Example 1> Condition: Reading out position register (Address 016&017) = 000
Effective Line Register
(Address 019&020)
Effective Lines
Total Line Register
+1 H
Frame Rate
0
3 H
709 H
44 fps
・
・
・
・
159
480 H
1027 H
30 fps
・
・
・
・
255
768 H
1219 H
26 fps
・
・
・
・
341
1026 H
1391 H
22 fps
・
・
・
・
399
1200 H
1507 H
21 fps
・
・
・
・
685
2058 H
2079 H
15 fps

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
17
9. Remote Communication Function
Via camera link cable, the camera can be controlled.
(1) The settings for RS232C
(2) Control code
・The total control code is 14 bytes, which conforms to ASCII code.
・The control code consists of camera No. process code, remote controller address, remote
controller data, and CR. Execute Read/Write through PC, and the camera will reply the data.
1
2
3
4
5
6
7th Byte
8
9
10
11
12
13
14
Camera No.
Process code
Remote controller
address
Remote controller data
CR
000000: fixed
“R”Read mode
Please refer to the
address table of Section
5. Function Settings.
000～255
0 Dh
“W”Write mode
“C”Camera mode
Camera No. is fixed with 6 bytes numerical strings, “000000”.
Process code
Input any one of R, W, or C to the process code.
R (read mode) is to read the data of remote controller address.
Please be noted to set any dummy data (000～255) to 11th ～13th, since a command shall
consists of 14 bytes.
W (write mode) is to write the data to the remote controller address.
Please be noted that the data cannot be saved into EEPROM of the camera.
(Reboot the camera, and the data is reset to the initial setting.)
To save the data into EEPROM, please refer to Section 5. Function Settings.
C is the code to send the data back from the camera.
Note: Do not set code C when sending the data from PC side.
Baud rate
:9600bps
Data
:8bit
Stop bit
:1bit
Parity
:None
XON/XOFF
:Not controlled

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
18
Remote controller address
Note: Do not write the data into the address other than specified, since it may cause
the damages or malfunction of the camera.
Remote controller data
Set the decimal number (000～255) for the remote controller data. Please be noted to set any
dummy data at read control mode.
CR
Be sure to input “CR”to confirm the end of the command.
※Note: The data set with 2 Byte shall be set with High Byte first, then set with Low Byte. The
camera rewrites the internal resister when receiving Low Byte.
10. Initial Settings
Function
Address
Data
Gain
001
0:
0
dB
E-Shutter
002
0:
1/15s(OFF)
Trigger Shutter Mode
004
0:
Normal Shutter Mode (Trigger Mode OFF)
Trigger Polarity
011
0:
Positive Input
Trigger Input
012
0:
Camera Link
Output Data Select
013
0:
8bit Output Data
Partial Scan Mode
015
0:
Full Frame Scan Mode
Partial Scan Total Line
021&022
2078:
Read Only
Baud Rate
030
0:
9600bps
Frame ID ON/OFF
060
0:
OFF
SOPT Mode
062
0:
45M Mode
SOPT Standby
063
0:
Standby OFF
SOPT Long Term Exposure
Mode
098&099
2079:
OFF
※In this Specification, we describe pixel shifting technology as “SOPT: Spatial Offsetting Pickup Technique”.

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
19
11. SOPT Control
11.1. Software Trigger Control Sequence
Start
SOPT
Mode Setting
Change to 45M Mode Change to 125M Mode
45M
125M
Send Control Command
000000W062000
Send Control Command
000000W062001
Software Trigger Mode
Standby
Send Control
Command
000000W063002
Capturing Images
Image synthesis
Repeat ?
Completion
Yes
No
Cancel Standby
Send Control Command
000000W063000
Camera output
45M Mode：9pcs.
125M Mode：25pcs.
Without
Change
Software Trigger
Output
Send Control
Command
000000W061000

VCC-GM60FV11CL Rev. 900-713-32
©2012 CIS Corporation. All rights reserved.
20
11.2. External Trigger Control Sequence
Start
SOPT
Mode Setting
Change to 45M Mode Change to 125M Mode
45M
125M
Send Control
Command
000000W062000
Send Control
Command
000000W062001
External Trigger Mode
Standby
Send Control Command
000000W063001
Capturing Images
Image Synthesis
Repeat ?
Completion
Yes
No
Cancel Standby
Send Control
Command
000000W063000
Camera Output
45M Mode：9pcs
125M Mode：
25pcs
External Trigger
Output
Without
Change