Cisco 6200 Use and care manual

78-5294-02 10/02/98

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Cisco 6200 FRU Installation and

Replacement

Read this document to learn how to install and remove ﬁeld-replaceable units (FRUs) in the

Cisco 6200 advanced digital subscriber line access multiplexer (DSLAM).

A Cisco 6200 DSLAM contains at least one of each of these FRUs:

•Network trunk card (NTC)

•Management processor card (MPC)

•Subscriber line card (SLC)

•Power entry module (PEM)

•Fan tray with air ﬁlter

•Dangler cable

This document includes the following sections:

•Installing and Removing Cards, page 2

•Installing and Removing a Power Entry Module (PEM), page 8

•Installing and Removing a Fan Tray, page 10

•Installing and Removing Dangler Cables, page 12

Cisco documentation and additional literature are available in a CD-ROM package, which ships with

your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated

monthly. Therefore, it might be more current than printed documentation. To order additional copies

of the Documentation CD-ROM, contact your local sales representative or call customer service.

The CD-ROM package is available as a single package or through an annual subscription. You can

also access Cisco documentation on the World Wide Web at http://www.cisco.com,

http://www-china.cisco.com, or http://www-europe.cisco.com.

If you are reading Cisco product documentation on the World Wide Web, you can submit comments

electronically. Click Feedback in the toolbar and select Documentation. After you complete the

form, click Submit to send it to Cisco. We appreciate your comments.

The safety warnings in this document have been translated into several foreign languages. See

Appendix C, “Translated Safety Warnings,” in the Cisco 6200 User Guide.

Installing and Removing Cards 78-5294-02 10/02/98

2Cisco 6200 FRU Installation and Replacement

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause

serious burns or weld the metal object to the terminals.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning Only trained and qualiﬁed personnel should be allowed to install or replace this equipment.

1. Installing and Removing Cards

1.1 Installing Cards in the Cisco 6200

Follow the procedures in this section to install MPCs, NTCs, and SLCs. It is not necessary to

disconnect power before inserting any card into the Cisco 6200 chassis.

Note All the SLCs in a Cisco 6200 chassis should be of the same type. The mixture of CAP and

DMT cards in a single chassis is not supported.

If you are installing a single-mode NTC OC-3 or NTC STM-1 card, read the following warnings.

Warning Class 1 laser product.

Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is

connected, avoid exposure to laser radiation and do not stare into open apertures.

The ﬁber optic communication channels in the single-mode OC-3 and STM-1 cards (NTC OC3-SM

and NTC STM1-SM) operate with laser energy, which can be harmful, especially to the eyes. During

normal operation, this energy is conﬁned to the cable and presents no danger. To avoid injury when

you are connecting or disconnecting optical channels, observe these precautions: always disconnect

the card from the backplane before connecting or disconnecting optical cables; always keep the

protective cap on the optic connector when the connector is not in use; and never look into an optical

cable or connector.

These cautions apply to all Cisco 6200 cards:

Caution Static voltages as low as 30 volts can cause latent damage to circuitry. Be sure to observe all

standard anti-static procedures (for example, wear a grounding strap).

Caution To avoid damage to either the card or the corresponding backplane connectors, be sure that you

understand and follow the proper procedure for inserting a card into the shelf. Damage may result if you

install a card into a slot of the wrong type, or if you install a card improperly.

78-5294-02 10/02/98 Installing and Removing Cards

Cisco 6200 FRU Installation and Replacement 3

1.1.1 Card Installation

To insert a card into the Cisco 6200 shelf, follow these steps:

Step 1 If you are installing a replacement MPC, remove the PCMCIA Flash card from the old

MPC and place it in the left PCMCIA slot in the new MPC.

Step 2 Select a slot compatible with the type of card you are inserting. An NTC must go in slot 1;

an MPC must go in slot 2; SLCs go in slots 5 through 14.

Step 3 Hold the card vertically, with the card’s faceplate toward you and connectors away from

you. Ensure that it is right side up by noting the lettering on the faceplate.

Step 4 Carefully align the upper and lower edges of the card with the upper and lower guides in

the shelf.

Caution To ensure that the card mates properly with connector pins on the backplane, the card length and

card slots have been designed with very close tolerances. To slide the card into the slot requires gentle

pressure with each hand, at the top and bottom of the faceplate.

Step 5 Gently insert the card into the slot. Stop when contact is ﬁrst made between the card and

the backplane.

Step 6 Ensure that the card’s upper and lower insertion/extraction levers engage the upper and

lower front rails of the enclosure. See Figure 1.

Figure 1 Card Insertion

Step 7 Press the upper lever down and the lower lever up at the same time. (This action

electrically connects the card to the backplane.)

Step 8 Secure the card to the enclosure by tightening the upper and lower retaining screws.

Step 9 Repeat Step 2 through Step 8 to install additional cards.

12700

Top lever

Bottom lever

Retaining screw

Top rail

Faceplate

Card

Guide

Bottom rail

Retaining screw

Front view of Cisco 6200 chassis

Installing and Removing Cards 78-5294-02 10/02/98

4Cisco 6200 FRU Installation and Replacement

When a card is inserted, the green POWER LED on its faceplate turns on. The card

performs an internal conﬁdence test. Each card’s READY LED turns on when the card

successfully completes its test.

Step 10 Install blank faceplates to cover any unused slots in the chassis. Like cards, faceplates are

each held in place by two retaining screws.

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that

might disrupt other equipment; and they direct the ﬂow of cooling air through the chassis. Do not operate the

system unless all cards, faceplates, front covers, and rear covers are in place.

Step 11 How to proceed:

•If you installed an NTC, do the following:

—Attach the appropriate trunk cable to the port on the faceplate.

—You may wish to monitor and manage the NTC using the Cisco 6200 Manager

software, a graphical user interface (GUI) management application. In order to

use the GUI to manage the NTC, you must provision the NTC in the GUI. See the

User Guide for the Cisco 6200 Manager for instructions on using the GUI.

You can also use the command line interface (CLI) to monitor and manage the

NTC. For the CLI, no conﬁguration of the NTC is required.

•If you installed an MPC, do the following:

—Attach the console cable to the CNSL port on the faceplate.

—If you are using Ethernet for out-of-band management of the Cisco 6200, attach

an Ethernet cable to the ENET port on the faceplate.

—Skip to the “Additional Steps for MPC Replacement” section on page 6.

•If you installed an SLC, do the following:

—Proceed to the “Software Conﬁguration for SLCs” section, below.

—Connect a cable to the appropriate subscriber port or dangler cable on the rear of

the chassis. See the “Installing Dangler Cables on the Cisco 6200” section on

page 12.

Warning The ports labeled “Ethernet,” “ENET,” “ETH1,” “ETH2,” “CNSL,” and “Serial Port” are safety

extra-low voltage (SELV) circuits. SELV circuits should be connected only to other SELV circuits. Because

the DSL circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the

telephone network voltage (TNV) circuits.

1.1.2 Software Conﬁguration for SLCs

Software conﬁguration for new SLCs is performed using either the Cisco 6200 Manager software (a

graphical user interface (GUI) management application) or the command line interface (CLI) to the

Cisco 6200. See the User Guide for the Cisco 6200 Manager for instructions on using the GUI.

This section explains how to use CLI commands to conﬁgure the SLC interfaces on a Cisco 6200

system. You can follow these steps before or after you insert the SLC into its slot in the chassis.

78-5294-02 10/02/98 Installing and Removing Cards

Cisco 6200 FRU Installation and Replacement 5

To conﬁgure an SLC, you must be in global conﬁguration mode. If you are already in this mode, start

with Step 3.

Step 1 Enter the enable command and then enter the password to go into privileged mode:

c6200> enable

Enter Password:

Step 2 Enter the conﬁgure command and press Return to accept “terminal,” the default.

c6200# configure

Configuring from terminal, memory, or network [terminal]?

c6200(config)#

Step 3 If you already inserted the card you want to conﬁgure into its slot, go to Step 4. If the card

is not in the slot, use this step to preconﬁgure the card.

Enter the c6200 card command and specify a slot number and card type. The SLC goes

into a slot with a number in the range 5 to 14 and has a card type of slc1-8-cap or

slc1-8-dmt. Each card has eight ports, numbered 0 to 7.In the following example, an SLC

8CAP is being preconﬁgured for slot 5.

c6200(config)# c6200 card 5 slc1-8-cap

Step 4 Enter the interface dsl command and specify the card and port you want to conﬁgure. In

this example, you conﬁgure port 0 of the SLC in slot 5.

c6200(config)# interface dsl 5/0

Step 5 Specify a subscriber name. In this example, the subscriber name “boston” is speciﬁed. If

you skip this step, the system provides a default subscriber name in the form port-type

slot/port, for example, “dsl 5/0.”

c6200(config-if)# dsl subscribername boston

Note Use the no dsl subscribername command to remove the subscriber name. This

command also changes all conﬁguration values for this interface to default values.

Step 6 Specify downstream and upstream bit rates, which in this example have been set to 1600

and 272 kbps, respectively:

c6200(config-if)# dsl bitrate downstream 1600 upstream 272

Step 7 Activate the conﬁguration by entering the no shutdown command and return to the

global conﬁguration prompt by entering the end command.

c6200(config-if)# no shutdown

c6200(config-if)# end

c6200(config)#

Repeat Step 4 through Step 7 for each of the interfaces that you want to conﬁgure, and then follow

the step below to save the conﬁguration to nonvolatile memory. If you do not save it, the

conﬁguration will be lost when the device is rebooted.

Step 8 To save the conﬁguration, use the end command to return to privileged EXEC mode, and

copy the running conﬁguration to the startup conﬁguration:

c6200# end

c6200# copy running-config startup-config

Installing and Removing Cards 78-5294-02 10/02/98

6Cisco 6200 FRU Installation and Replacement

Step 9 In addition to saving the conﬁguration to the startup conﬁguration, you may want to copy

it to a PCMCIA Flash memory card. The following command copies the startup

conﬁguration to a ﬁle named “6200-conﬁg” on the PCMCIA card in slot 0.

c6200# copy startup-config slot0:6200-config

1.1.3 Additional Steps for MPC Replacement

If you are replacing an MPC, follow these steps after you complete the steps in the “Card

Installation” section on page 3. This procedure does not interrupt the ﬂow of data.

Note In this procedure, it is assumed that you have prepared a backup PCMCIA Flash card, as

described in the Cisco 6200 User Guide in Chapter 6, “Preventive Maintenance.” The backup

PCMCIA card should contain the Cisco IOS software image and the current conﬁguration ﬁle for

the system. The backup PCMCIA card should be moved from the old MPC to the new MPC before

the new MPC is installed in the chassis.

Step 1 At the console, look for this prompt and answer No:

Would you like to enter the initial configuration dialog? [yes]: no

Step 2 At the Router> or c6200> prompt, enter enable and the password to access privileged

EXEC mode:

C6200> enable

Password:

c6200#

Step 3 Enter the dir command to display the names of the ﬁles on the PCMCIA card in slot 0:

6200# dir slot0:

-#- -length- -----date/time------ name

1 1166308 Jul 06 1998 14:33:55 c6200-dcm-mz.113-1.DA1.bin

2 1121 Jul 06 1998 14:44:30 6200-config

19410616 bytes available (1167688 bytes used)

Step 4 Enter the copy command to copy the conﬁguration ﬁle from the PCMCIA card to

running-conﬁg in memory:

6200# copy slot0:6200-config running-config

6200#

%SYS-5-CONFIG: Configured from slot0:6200-config by console #

Step 5 Enter another copy command to copy the conﬁguration ﬁle from the PCMCIA card to

startup-conﬁg in NVRAM:

6200# copy slot0:6200-config startup-config

Building configuration...

78-5294-02 10/02/98 Installing and Removing Cards

Cisco 6200 FRU Installation and Replacement 7

Step 6 To enable the interfaces, enter the conﬁgure terminal command, followed by the

conﬁguration commands shown in this example:

6200# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

6200(config)# int e0/0

6200(config-if)# no shut

6200(config-if)# int e0/1

6200(config-if)# no shut

6200(config-if)# int atm 1/0

6200(config-if)# no shut

6200(config-if)# exit

6200(config)# exit

6200# copy running-config startup-config

Building configuration...

[OK]

6200#

1.2 Removing Cards from the Cisco 6200

The procedure for removing MPCs, NTCs, and SLCs is the same. It is not necessary to disconnect

power before removing any card from the Cisco 6200 DSLAM.

Caution Static voltages as low as 30 volts can cause latent damage to circuitry. Be sure to observe all

standard anti-static procedures (for example, wear a grounding strap).

Step 1 Disconnect any cables connected to the card you are about to remove. If you are

disconnecting a single-mode OC-3 or STM-1 card, read the following warnings.

Warning Class 1 laser product.

Warning Because invisible laser radiation may be emitted from the aperture of the port when no cable is

connected, avoid exposure to laser radiation and do not stare into open apertures.

The ﬁber optic communication channels in the single-mode OC-3 and STM-1 cards (NTC OC3-SM

and NTC STM1-SM) operate with laser energy, which can be harmful, especially to the eyes. During

normal operation this energy is conﬁned to the cable and presents no danger. To avoid injury when

connecting or disconnecting optical channels, observe these precautions: always disconnect the card

from the backplane before connecting or disconnecting optical cables; always keep the protective

cap on the optic connector when the connector is not in use; and never look into an optical cable or

connector.

Step 2 Unscrew the upper and lower retaining screws that secure the card to the chassis.

Step 3 Grasp the upper and lower extraction levers. Pull up on the upper lever while pushing

down on the lower lever. This action disengages the card from the connectors on the

backplane.

Step 4 Slide the card out of the chassis.

Step 5 Placethe card onan antistaticsurface. Ifit willbe out of the chassisfor anylength oftime,

put it in an antistatic shielding bag or in a box lined with antistatic material.

Step 6 In the empty slot, install another card of the same type or a blank faceplate.

Installing and Removing a Power Entry Module (PEM) 78-5294-02 10/02/98

8Cisco 6200 FRU Installation and Replacement

Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that

might disrupt other equipment; and they direct the ﬂow of cooling air through the chassis. Do not operate the

system unless all cards, faceplates, front covers, and rear covers are in place.

1.2.1 Software Conﬁguration

If you are removing the card permanently, update the system conﬁguration using the Cisco 6200

Manager (GUI) or the command line interface (CLI). For instructions, see

•User Guide for the Cisco 6200 Manager

•Cisco 6200 User Guide (includes CLI procedures)

2. Installing and Removing a Power Entry Module (PEM)

2.1 Installing a PEM in the Cisco 6200

The power bays are located at front of the chassis, near the top. The bay on the left is wired to power

circuit A; the bay on the right is wired to power circuit B. (The circuits are identiﬁed at the power

terminals on the backplane.)

It is not necessary to disconnect power before inserting a PEM into the Cisco 6200 chassis. Follow

these steps:

Step 1 Ensure that the circuit breaker on the PEM is turned to OFF (0).

Step 2 Use a Phillips screwdriver to remove the front panel that partially covers the power bays.

Two Phillips-head quarter-turn fasteners are recessed into the face of the panel; insert the

screwdriver and turn the fastener 90 degrees in either direction to release it.

Step 3 Engage the sheet-metal carrier that forms the top of the PEM with the brackets on each

side of the power bay. (See Figure 2.)

Step 4 Firmly push the PEM all the way into the power bay to ensure that the power connectors

mate.

Step 5 Tighten the captive screw on the faceplate of the PEM to secure the PEM to the chassis.

Step 6 If the chassis is connected to power, turn the circuit breaker on the PEM to ON. A green

LED on the faceplate comes on to indicate that the PEM is providing power to the chassis.

Step 7 Replace the front panel and use a Phillips screwdriver to fasten it in place. You can look

through the rectangular opening in the panel as you engage the fasteners. Turn the

fastener 90 degrees in either direction to secure it.

78-5294-02 10/02/98 Installing and Removing a Power Entry Module (PEM)

Cisco 6200 FRU Installation and Replacement 9

Figure 2 Power Entry Module in the Cisco 6200 Chassis

2.2 Removing a PEM from the Cisco 6200

If you remove a PEM from a Cisco 6200 chassis in which a second PEM is installed and providing

power to the chassis, the chassis continues to operate normally. If you plan to remove the only

operating PEM from a chassis, you should shut down the system ﬁrst.

2.2.1 Shutting Down the Cisco 6200

Follow these steps to shut down and turn off the DSLAM.

Step 1 Before shutting down the Cisco 6200, use the copy command to save any conﬁguration

changes to NVRAM, and also, if you wish, to a PCMCIA Flash card. (See the command

reference chapter of the Cisco 6200 User Guide for instructions on using copy.)

Step 2 Allow any copy or write operations involving Flash media (PCMCIA slots or boot Flash)

to complete.

Step 3 Turn the circuit breakers on both PEMs to OFF (0).

2.2.2 Extracting a PEM

Follow these steps to remove a PEM from the Cisco 6200 chassis. If you are removing the only

operating PEM in an active system, follow the previous procedure, “Shutting Down the Cisco 6200,”

before performing these steps.

Step 1 Ensure that the circuit breaker on the PEM you are about to remove is turned to OFF (0).

Step 2 Use a Phillips screwdriver to remove the front panel that partially covers the power bays.

Two Phillips-head quarter-turn fasteners are recessed into the face of the panel; insert the

screwdriver and turn the fastener 90 degrees in either direction to release it.

Step 3 Unscrew the retaining screw in the PEM faceplate.

Step 4 Grasp the PEM by the handle on its faceplate and pull it out of the chassis.

12698

Circuit

breaker

Front

panel

PEM

Retaining

screw

LED

Installing and Removing a Fan Tray 78-5294-02 10/02/98

10 Cisco 6200 FRU Installation and Replacement

Warning Hold the PEM by the sheet-metal carrier (top and front) only. Internal components may be hot.

Step 5 Replace the front panel and use the Phillips screwdriver to fasten it in place. You can look

through the rectangular opening in the panel as you engage the fasteners. Turn the

fastener 90 degrees in either direction to secure it.

3. Installing and Removing a Fan Tray

3.1 Installing the Fan Tray in the Cisco 6200

The fan tray is located at the bottom of the chassis, behind a removable panel. You need a Phillips

screwdriver to remove and replace the panel.

Caution The Cisco 6200 cooling fans must run continuously. The system may suffer thermal damage if the

fans stop for more than 10 minutes. (At ambient temperatures above 104 F(40 C),thermal damage may occur

sooner.)

Follow these steps to install the fan tray:

Step 1 Use a Phillips screwdriver to remove the panel that covers the fan tray (see Figure 3).

Step 2 Hold the fan tray so that the fans are on top, the air ﬁlter is on the bottom, and the wide

edge of the tray is facing away from you.

Step 3 Tilting the front edge of the fan tray downward, insert the wide edge of the tray so that it

clears the bottom lip of the chassis. (See Figure 3.)

Step 4 Engage the edges of the fan tray with the guides on either side of the slot in the chassis.

Ensure that the edges of the fan tray rest on top of the guides in the slot.

Step 5 Slide the tray gently into place. Press ﬁrmly to ensure that the power connectors mate. If

the chassis is receiving power, you will hear the fans start to turn.

Step 6 Use the Phillips screwdriver to replace the panel over the fan tray.

78-5294-02 10/02/98 Installing and Removing a Fan Tray

Cisco 6200 FRU Installation and Replacement 11

Figure 3 Fan Tray in the Cisco 6200

3.2 Removing the Fan Tray from the Cisco 6200

If you must remove the fan tray from a Cisco 6200, replace it within a few minutes. If that is not

possible, it is recommended that you shut down the system and turn off power to avoid thermal

damage.

Caution It is important that the system’s cooling fans run continuously. The system might suffer thermal

damage if the fans stop for more than ten minutes. (At ambient temperatures above 104 F(40C), thermal

damage can occur sooner.)

You need a Phillips screwdriver to perform this procedure.

Follow these steps to remove the fan tray:

Step 1 Use a Phillips screwdriver to remove the panel that covers the fan tray area at the bottom

front of the chassis.

Step 2 Grasp the fan tray with both hands and gently pull it toward you. If the fans are running,

you will hear them slow down as the tray disengages from its power connector.

Step 3 As you pull the fan tray from the chassis, tilt the front edge downwards so the wide rear

edge clears the lip at the bottom of the chassis. (See Figure 3.)

3.3 Air Filter Maintenance

Cleaning and replacement of the air ﬁlter in the fan tray is covered in the Cisco 6200 User Guide in

Chapter 6, “Preventive Maintenance.”

12699

Cisco6200

SERIES

Fan tray

Front panel

Air filter

Installing and Removing Dangler Cables 78-5294-02 10/02/98

12 Cisco 6200 FRU Installation and Replacement

4. Installing and Removing Dangler Cables

4.1 Installing Dangler Cables on the Cisco 6200

This procedure tells you how to attach dangler cables to the 50-pin Champ connectors on the back

of the Cisco 6200 DSLAM. (The Champs provide unshielded twisted pair (UTP) connections for

subscriber trafﬁc.)

Thedangler cablesare numbered J1 through J10.Figure 4and Table 1showwhich Champconnector

each dangler cable should be attached to.

Figure 4 Attach Dangler Cables to Champ Connectors

Each dangler cable serves the subscriber line card (SLC) in a particular slot. The dangler cables

correspond to the SLC slots as shown in Table 1.

13064

J10

Do not attach

a dangler cable

to this connector

Rear view of Cisco 6200 chassis

78-5294-02 10/02/98 Cisco Connection Online

Cisco 6200 FRU Installation and Replacement 13

Table 1 Dangler Cables Mapped to SLC Slots

You need a Phillips screwdriver to install the dangler cables. Follow these steps:

Step 1 Use a Phillips screwdriver to unfasten one of the two metal panels that cover the Champ

connectors on the back of the Cisco 6200. Each panel is held in place by six Phillips-head

quarter-turn fasteners. Turn each fastener 90 degrees in either direction to release it.

Step 2 Attach dangler cables to the ﬁve connectors (see Figure 4). Secure the cables with the

wire clips attached to the backplane connectors.

Step 3 Routethe danglercables towardthe sidesof thechassis: twotoone side,three tothe other.

Step 4 Replace the metal cover and use a Phillips screwdriver to fasten it in place. Turn each

fastener 90 degrees in either direction to secure it.

Step 5 Repeat this procedure, if necessary, to install dangler cables behind the other panel.

Note There are six Champ connectors behind the bottom panel. Do not attach a dangler

cable to the Champ connector located above and to the right of the other ﬁve connectors.

See Figure 4.

4.2 Removing Dangler Cables from the Cisco 6200

Follow these steps to remove dangler cables from the back of the Cisco 6200 DSLAM. You need a

Phillips screwdriver to perform this procedure.

Step 1 Use a Phillips screwdriver to unfasten one of the two metal panels that cover the dangler

cables on the back of the Cisco 6200. Each panel is held in place by six Phillips-head

quarter-turn fasteners. Turn each fastener 90 degrees in either direction to release it.

Step 2 Unfasten the two wire clips holding each dangler cable in place, and then pull the cable

off the connector.

Step 3 Replace the metal cover and use a Phillips screwdriver to fasten it in place. Turn each

fastener 90 degrees in either direction to secure it.

Step 4 Repeat this procedure, if necessary, to remove the dangler cables behind the other panel.

5. Cisco Connection Online

CiscoConnection Online(CCO) isCisco Systems’primary, real-timesupport channel.Maintenance

customers and partners can self-register on CCO to obtain additional information and services.

Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added

services to Cisco’s customers and business partners. CCO services include product information,

product documentation, software updates, release notes, technical tips, the Bug Navigator,

conﬁguration notes, brochures, descriptions of service offerings, and download access to public and

authorized ﬁles.

J1 Slot 5 J6 Slot 10

J2 Slot 6 J7 Slot 11

J3 Slot 7 J8 Slot 12

J4 Slot 8 J9 Slot 13

J5 Slot 9 J10 Slot 14

Cisco Connection Online 78-5294-02 10/02/98

14 Cisco 6200 FRU Installation and Replacement

CCO serves a wide variety of users through two interfaces that are updated and enhanced

simultaneously: a character-based version and a multimedia version that resides on the World Wide

Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet

e-mail,and it isexcellentfor quickaccess to informationoverlowerbandwidths.The WWWversion

of CCO provides richly formatted documents with photographs, ﬁgures, graphics, and video, as well

as hyperlinks to related information.

You can access CCO in the following ways:

•WWW: http://www.cisco.com

•WWW: http://www-europe.cisco.com

•WWW: http://www-china.cisco.com

•Telnet: cco.cisco.com

•Modem: From North America, 408 526-8070; from Europe, 33 1 64 46 40 82. Use the

following terminal settings: VT100 emulation; databits: 8; parity: none; stop bits: 1; and

connection rates up to 28.8 kbps.

For a copy of CCO’s Frequently Asked Questions (FAQ), contact [email protected]. For

additional information, contact [email protected].

Note If you are a network administrator and need personal technical assistance with a Cisco

product that is under warranty or covered by a maintenance contract, contact Cisco’s Technical

Assistance Center (TAC) at 800 553-2447, 408 526-7209, or [email protected]. To obtain general

information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387,

408 526-7208, or [email protected].

This document is to be used in conjunction with the Cisco 6200 User Guide.

AccessPath, Any to Any, AtmDirector, the CCIE logo, CD-PAC, Centri, the Cisco Capital logo, CiscoLink, the Cisco NetWorks logo, the Cisco Powered Network logo, the Cisco Press

logo, ClickStart, ControlStream, DAGAZ, Fast Step, FireRunner, IGX, IOS, JumpStart, Kernel Proxy, LoopRunner, MGX, Natural Network Viewer, NetRanger, NetSonar, Packet, PIX,

Point and Click Internetworking, Policy Builder, RouteStream, Secure Script, SMARTnet, SpeedRunner, Stratm, StreamView, The Cell, TrafficDirector, TransPath, VirtualStream,

VlanDirector, Workgroup Director, and Workgroup Stack are trademarks; Changing the Way We Work, Live, Play, and Learn and Empowering the Internet Generation are service marks;

and BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, Enterprise/Solver, EtherChannel, FastHub, ForeSight, FragmentFree, IP/TV, IPX,

LightStream, MICA, Phase/IP, StrataSphere, StrataView Plus, and SwitchProbe are registered trademarks of Cisco Systems, Inc. in the U.S. and certain other countries. All other trademarks

mentioned in this document are the property of their respective owners. (9808R)