Cisco ASA 5508-X User manual

Cisco Systems, Inc. www.cisco.com
1
Cisco ASA 5508-X and ASA 5516-X
Quick Start Guide
First Published: April 7, 2015
Last Updated: April 27, 2017
1. Package Contents
This section lists the package contents of the chassis. Note that contents are subject to change, and your exact
contents might contain additional or fewer items.
1ASA 5508-X or ASA 5516-X chassis 2USB Console Cable (Type A to Type B)
3Power cable 44 10-32 Phillips Screws for rack mounting
54 12-24 Phillips Screws for rack mounting 64 M6 Phillips Screws for rack mounting
74 M4 Phillips Screws for rack mounting
1
3
2
353664
67 5
4

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
2. License Requirements
2
2. License Requirements
ASA Licenses
The ASA 5508-X or ASA 5516-X includes the Base license by default, along with the Strong Encryption
(3DES/AES) license if you qualify for its use. You can also purchase the following licenses:
Security Context
AnyConnect Plus or Apex
If you need to manually request the Strong Encryption license (which is free), see
http://www.cisco.com/go/license.
If you want to upgrade from the Base license to the Security Plus license, or purchase an AnyConnect license, see
http://www.cisco.com/go/ccw. See also the Cisco AnyConnect Ordering Guide and the AnyConnect Licensing
Frequently Asked Questions (FAQ). You will then receive an email with a Product Authorization Key (PAK) so you
can obtain the license activation key. For the AnyConnect licenses, you receive a multi-use PAK that you can apply
to multiple ASAs that use the same pool of user sessions.
Note: The serial number used for licensing is different from the chassis serial number printed on the outside of
your hardware. The chassis serial number is used for technical support, but not for licensing. To view the licensing
serial number, enter the show version | grep Serial command or see the ASDM Configuration > Device
Management > Licensing Activation Key page.
ASA FirePOWER Licenses
The ASA FirePOWER module uses a separate licensing mechanism from the ASA. No licenses are pre-installed,
but the box includes a PAK on a printout that lets you obtain a license activation key for the following licenses:
Control and Protection—Control is also known as “Application Visibility and Control (AVC)” or “Apps”.
Protection is also known as “IPS”. In addition to the activation key for these licenses, you also need
“right-to-use” subscriptions for automated updates for these features.
The Control (AVC) updates are included with a Cisco support contract.
The Protection (IPS) updates require you to purchase the IPS subscription from
http://www.cisco.com/go/ccw. This subscription includes entitlement to Rule, Engine, Vulnerability, and
Geolocation updates. Note: This right-to-use subscription does not generate or require a PAK/license
activation key for the ASA FirePOWER module; it just provides the right to use the updates.
Other licenses that you can purchase include the following:
Advanced Malware Protection (AMP)
URL Filtering
These licenses do generate a PAK/license activation key for the ASA FirePOWER module. See the Cisco Firepower
System Feature Licenses for more information.
To install the Control and Protection licenses and other optional licenses, see Install the Licenses, page 6.
3. Deploy the ASA 5508-X or ASA 5516-X in Your
Network
The following figure shows the recommended network deployment for the ASA 5508-X or ASA 5516-X with the
ASA FirePOWER module:

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
3. Deploy the ASA 5508-X or ASA 5516-X in Your Network
3
Note: You must use a separate inside switch in your deployment.
The default configuration enables the above network deployment with the following behavior.
inside --> outside traffic flow
outside IP address from DHCP
DHCP for clients on inside
Management 1/1 belongs to the ASA FirePOWER module. The interface is Up, but otherwise unconfigured
on the ASA. The ASA FirePOWER module can then use this interface to access the ASA inside network and
use the inside interface as the gateway to the Internet.
Note: Do not configure an IP address for this interface in the ASA configuration. Only configure an IP address
in the Firepower configuration. You should consider this interface as completely separate from the ASA in
terms of routing.
ASDM access on the inside interface
Note: If you want to deploy a separate router on the inside network, then you can route between management and
inside. In this case, you can manage both the ASA and ASA FirePOWER module on Management 1/1 with the
appropriate configuration changes.
Procedure
1. Cable the following to a Layer 2 Ethernet switch:
Layer 2
Switch
ASA
inside
Management 1/1
No ASA IP address
ASA FirePOWER IP address: 192.168.1.2
outside
ASA FirePOWER Default Gateway
GigabitEthernet 1/2
192.168.1.1
GigabitEthernet 1/1
FP
Internet
(May be required)
Firepower Management Center
Computer
1 23 4567 8
sL
CONSOLE
GigabitEthernet 1/1
outside, DHCP from Modem
Management 1/1
Must set to 192.168.1.2
(ASA FirePOWER Management)
Internet
Layer 2 Switch
WAN Modem
Management Computer
DHCP from inside: 192.168.1.x
GigabitEthernet 1/2
inside, 192.168.1.1
(ASA Management;
Gateway)

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
4. Power On the ASA
4
—GigabitEthernet 1/2 interface (inside)
—Management 1/1 interface (for the ASA FirePOWER module)
—Your computer
Note: You can connect inside and management on the same network because the management interface acts
like a separate device that belongs only to the ASA FirePOWER module.
2. Connect the GigabitEthernet 1/1 (outside) interface to your WAN device, for example, your cable modem.
Note: If the cable modem supplies an outside IP address that is on 192.168.1.0/24, then you must change the
ASA configuration to use a different IP address. Interface IP addresses, HTTPS (ASDM) access, and DHCP
server settings can all be changed using the Startup Wizard. If you change the IP address to which you are
connected to ASDM, you will be disconnected when you finish the wizard. You must reconnect to the new IP
address.
4. Power On the ASA
1. Attach the power cable to the ASA and connect it to an electrical outlet.
2. Press the Power button on the back of the ASA.
3. Check the Power LED on the front of the ASA; if it is solid green, the device is powered on.
4. Check the Status LED on the front of the ASA; after it is solid green, the system has passed power-on
diagnostics.
5. Launch ASDM
See the ASDM release notes on Cisco.com for the requirements to run ASDM.
Note: This procedure assumes you want to use ASDM to manage the ASA FirePOWER Module. If you want to use
the FireSIGHT System, then you need to connect to the module CLI and run the setup script; see the ASA
FirePOWER quick start guide.
Procedure
1. On the computer connected to the ASA, launch a web browser.
2. In the Address field, enter the following URL: https://192.168.1.1/admin. The Cisco ASDM web page
appears.
3. Click one of the available options: Install ASDM Launcher, Run ASDM, or Run Startup Wizard.
4. Follow the onscreen instructions to launch ASDM according to the option you chose. The Cisco ASDM-IDM
Launcher appears.
If you click Install ASDM Launcher, in some cases you need to install an identity certificate for the ASA and a
separate certificate for the ASA FirePOWER module according to Install an Identity Certificate for ASDM.
5. Leave the username and password fields empty, and click OK. The main ASDM window appears.
6. If you are prompted to provide the IP address of the installed ASA FirePOWER module, cancel out of the dialog
box. You must first set the module IP address to the correct IP address using the Startup Wizard.

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
6. Run Other ASDM Wizards and Advanced Configuration
5
ASDM can change the ASA FirePOWER module IP address settings over the ASA backplane; but for ASDM to
then manage the module, ASDM must be able to reach the module (and its new IP address) on the
Management 1/1 interface over the network. The recommended deployment allows this access because the
module IP address is on the inside network. If ASDM cannot reach the module on the network after you set
the IP address, then you will see an error.
7. Choose Wizards > Startup Wizard.
8. Configure additional ASA settings as desired, or skip screens until you reach the ASA FirePOWER Basic
Configuration screen.
Set the following values to work with the default configuration:
—IP Address—192.168.1.2
—Subnet Mask—255.255.255.0
—Gateway—192.168.1.1
9. Click I accept the agreement, and click Next or Finish to complete the wizard.
10. Quit ASDM, and then relaunch. You should see ASA FirePOWER tabs on the Home page.
6. Run Other ASDM Wizards and Advanced Configuration
ASDM includes many wizards to configure your security policy. See the Wizards menu for all available wizards.

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
7.Configure the ASA FirePOWER Module
6
To continue configuring your ASA, see the documents available for your software version at Navigating the Cisco
ASA Series Documentation.
7.Configure the ASA FirePOWER Module
Use ASDM to install licenses, configure the module security policy, and send traffic to the module.
Note: You can alternatively use the Firepower Management Center to manage the ASA FirePOWER module. See
the ASA FirePOWER Module Quick Start Guide for more information.
Install the Licenses
The Control and Protection licenses are provided by default and the Product Authorization Key (PAK) is included
on a printout in your box. If you ordered additional licenses, you should have PAKs for those licenses in your email.
Procedure
1. Obtain the License Key for your chassis by choosing Configuration > ASA FirePOWER Configuration >
Licenses and clicking Add New License.
The License Key is near the top; for example, 72:78:DA:6E:D9:93:35.
2. Click Get License to launch the licensing portal. Alternatively, in your browser go to
http://www.cisco.com/go/license.
3. Enter the PAKs separated by commas in the Get New Licenses field, and click Fulfill.
4. You will be asked for the License Key and email address among other fields.
5. Copy the resulting license activation key from either the website display or from the zip file attached to the
licensing email that the system automatically delivers.
6. Return to the ASDM Configuration > ASA FirePOWER Configuration > Licenses > Add New License screen.
7. Paste the license activation key into the License box.
8. Click Verify License to ensure that you copied the text correctly, and then click Submit License after
verification.
9. Click Return to License Page.
Configure the ASA FirePOWER Security Policy
Procedure
1. Choose Configuration > ASA FirePOWER Configuration to configure the ASA FirePOWER security policy.
Use the ASA FirePOWER pages in ASDM for information. You can click Help in any page, or choose Help >
ASA FirePOWER Help Topics, to learn more about how to configure policies.
See also the ASA FirePOWER module user guide.
Configure the ASA Security Policy
Procedure
1. To send traffic to the module, choose Configuration > Firewall > Service Policy Rules.

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
8. Where to Go Next
7
2. Choose Add > Add Service Policy Rule.
3. Choose whether to apply the policy to a particular interface or apply it globally and click Next.
4. Configure the traffic match. For example, you could match Any Traffic so that all traffic that passes your
inbound access rules is redirected to the module. Or, you could define stricter criteria based on ports, ACL
(source and destination criteria), or an existing traffic class. The other options are less useful for this policy.
After you complete the traffic class definition, click Next.
5. On the Rule Actions page, click the ASA FirePOWER Inspection tab.
6. Check the Enable ASA FirePOWER for this traffic flow check box.
7. In the If ASA FirePOWER Card Fails area, click one of the following:
—Permit traffic—Sets the ASA to allow all traffic through, uninspected, if the module is unavailable.
—Close traffic—Sets the ASA to block all traffic if the module is unavailable.
8. (Optional) Check Monitor-only to send a read-only copy of traffic to the module, i.e. passive mode.
9. Click Finish and then Apply.
Repeat this procedure to configure additional traffic flows as desired.
8. Where to Go Next
For more information about the ASA FirePOWER module and ASA operation, see the “ASA FirePOWER
Module” chapter in the ASA/ASDM firewall configuration guide, or the ASDM online help. You can find links to
all ASA/ASDM documentation at Navigating the Cisco ASA Series Documentation.
For more information about ASA FirePOWER configuration, see the online help or the ASA FirePOWER module
user guide or the FireSIGHT/Firepower Management Center system user guide.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To
view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property
of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other
company. (1110R)
© 2016 Cisco Systems, Inc. All rights reserved.

Cisco ASA 5508-X and ASA 5516-X Quick Start Guide
8. Where to Go Next
8