Cisco 1100 Series Manual

Hardware Installation Guide for the Cisco 1100 Terminal Gateway
First Published: 2020-05-25
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2020 Cisco Systems, Inc. All rights reserved.

CONTENTS
About Cisco 1100 Terminal Gateway Routers 1
CHAPTER 1
Chassis Views 1
LED Indicators 3
Power Supply 5
Slots and Interfaces 5
About Slots, Subslots, and Port Numbering 5
Async line Numbering 7
Fans, Ventilation and Airflow 8
Specifications of Cisco 1100 Series Integrated Services Routers 10
Periodic Inspection and Cleaning 10
Prepare for Router Installation 11
CHAPTER 2
Safety Recommendations 11
Safety With Electricity 12
Prevent Electrostatic Discharge Damage 12
General Site Requirements 13
Site Selection Guidelines 13
NEBS Deployment Site Requirements 14
Rack Requirements 15
Router Environmental Requirements 15
Power Guidelines and Requirements 16
Network Cabling Specifications 16
Console Port Connections 16
EIA/TIA-232 16
Console Port Considerations 16
Preparing for Network Connections 16
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
iii

Ethernet Connection 17
Required Tools and Equipment for Installation and Maintenance 17
Install and Connect the Router 19
CHAPTER 3
Unpack the Router 19
Rack Mount the Chassis 19
Attach Bracket to the Chassis 20
Mount the Router on the Rack 22
Chassis Grounding 23
Connect Power Cable 25
Connecting to DC Power 29
Connect to the Console Port with Mac OS X 32
Connect to the Console Port with Linux 32
Connect WAN and LAN Interfaces 33
Ports and Cabling 33
Connection Procedures and Precautions 35
Configure the Router at Startup 35
Install and Remove Small Form Pluggable Modules and Field Replaceable Units 37
CHAPTER 4
Install Small Form Pluggable Module 37
Install Field Replaceable Units 37
Installing and Removing a NIM 38
Remove and Replace SSD Storage 39
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
iv
Contents

CHAPTER 1
About Cisco 1100 Terminal Gateway Routers
Cisco 1100 Terminal Gateway Routers are terminal servers that provides asynchronous connections to the
console ports for Cisco devices.
Table 1: Base Models of the Cisco 1100 Terminal Gateway Routers
MemorySwitchNIM SlotAsynchronous PortsBase Models
2GB Dram/ 4GB
flash
NoneYes32C1100TG-1N32A
4GB Dram/ 4GB
flash
24 port L2 SwitchYes32C1100TG-1N24P32A
8GB Dram/ 8GB
flash
24 port L2 SwitchYes32C1100TGX-1N24P32A
For more information on the features and specifications of Cisco 1100 Series Terminal Gateway Routers,
refer to Cisco 1100 Terminal Gateway Routers datasheet.
•Chassis Views, on page 1
•LED Indicators, on page 3
•Power Supply, on page 5
•Slots and Interfaces, on page 5
•Fans, Ventilation and Airflow, on page 8
•Specifications of Cisco 1100 Series Integrated Services Routers, on page 10
•Periodic Inspection and Cleaning, on page 10
Chassis Views
This section contains front and back panel views of the Cisco 1100 Terminal Gateway Routers-showing
locations of the power and signal interfaces, interface slots, status indicators, and chassis identification labels.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
1

Figure 1: C1100TG-1N32A - I/O View
USB 2.02System LED1
GE WAN 0/0/1 – RJ45/SFP4GE WAN 0/0/0 - RJ45/SFP3
ASYNC 32 port6ASYNC 16 port5
NIM7
Figure 2: C1100TG-1N24P32A and C1100TGX-1N24P32A - I/O View
USB 2.02System LED1
GE WAN 0/0/1 – RJ45/SFP4GE WAN 0/0/0 - RJ45/SFP3
ASYNC 32 port6ASYNC 16 port5
Ethernet Switch LED 0-238Ethernet Switch 0-157
NIM10Ethernet Switch 16-239
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
2
About Cisco 1100 Terminal Gateway Routers
Chassis Views

Figure 3: C1100TG-1N32A - Rear View
6-pin Power Connector2USB 3.01
ASYNC LED4RJ-45 Console, AUX3
Power Supply6Grounding Attachment5
Figure 4: C1100TG-1N24P32A and C1100TGX-1N24P32A - Rear View
6-pin Power Connector2USB 3.01
ASYNC LED4RJ-45 Console, AUX3
Power Supply6Grounding Attachment5
LED Indicators
The following figures and table summarizes the LED indicators that are located on the chassis of the Cisco
1100 Terminal Gateway Routers.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
3
About Cisco 1100 Terminal Gateway Routers
LED Indicators

Figure 5: LED Indicators - C1100TG-1N32A I/O Side
Figure 6: LED Indicators - C1100TG-1N24P32A and C1100TGX-1N24P32A I/O Side
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
4
About Cisco 1100 Terminal Gateway Routers
LED Indicators

Table 2: LED Indicators for Cisco Cisco 1100 Terminal Gateway Router
Control SourceDescriptionLED ColorPort
Bezel side. All models.Off—Systempower offGreen and AmberSystem LEDs
Steady Green - System
operates normally.
Blinking Green —
BIOS/Rommon is
booting.
Steady Amber — Thermal
trip.
Blinking Amber – Alarm,
Secure boot failure.
Bezel SideOff— No linkGreen
LAN Port LEDs
Steady On— Link
Blink - TXD/RXD Data
Bezel SideGreen - Indicates SFP
module detected
Green and Amber
WAN Port LEDs
Amber - Indicates SFP is
not detected or at fault
Rear sidelink establishedGreen
ASYNC Port LEDs
Power Supply
The product power specifications are as follows:
• AC input voltage: 100 to 240 VAC, 1.6 A, 50-60 Hz
• DC input voltage: 48 to 60 VDC, 4.2 amp
• External power supply option - 100-240 VAC, 50 - 60 Hz
• HVDC power supply – 240 VDC, 0.9 A
Slots and Interfaces
About Slots, Subslots, and Port Numbering
The following figure shows slots and subslots numbering for C1100TG-1N32A:
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
5
About Cisco 1100 Terminal Gateway Routers
Power Supply

Figure 7: C1100TG-1N32A: Slots and Subslots
Slot 0/0 Front panel Gigabit Ethernet1
RJ45/SFP combo GigaEthernet 0/0/02
Slot 0/1 onboard Async serial
1 = 0-7
2 = 8-15
3 = 16-23
4 = 24-31
5 = 32-39
6 = 40-47
Async 0/1/0 ~ Async 0/1/47
3
Slot 0/2 NIM slot4
RJ45/SFP combo GigaEthernet 0/0/15
Figure 8: C1100TG-1N24P32A and C1100TGX-1N24P32A: Slots and Subslots
Slot 0/0 Front panel Gigabit Ethernet1
RJ45/SFP combo GigaEthernet 0/0/02
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
6
About Cisco 1100 Terminal Gateway Routers
About Slots, Subslots, and Port Numbering

Slot 0/1 onboard Async serial
1 = 0-7
2 = 8-15
3 = 16-23
4 = 24-31
5 = 32-39
6 = 40-47
Async 0/1/0 ~ Async 0/1/47
3
LAN 04
Slot 0/2 Onboard L2 switch GigaEthernet 0/2/0 ~ GigaEthernet 0/2/235
LAN 226
Slot 0/3 NIM slot7
LAN 238
LAN 19
RJ45/SFP combo GigaEthernet 0/0/110
Async line Numbering
Cisco 1100 Terminal Gateway Routers has 32 onboard async ports, line number starts at 2 and ends at 33.
An optional Daughter Card with 16 async ports can be added to Nanook base and Nanook+, line number for
Daughter Card starts at 33 and ends at 49.
Figure 9: C1100TG-1N32A: Line Numbering
GigaEthernet 0/0/0 to 0/0/11
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
7
About Cisco 1100 Terminal Gateway Routers
Async line Numbering

Async 0/1/0 to Async 0/1/47
0 = 2-9
1 = 10-17
2 = 18-25
3 = 26-33
4 = 34-41
5 = 42-49
2
NIM 0/23
Figure 10: C1100TG-1N24P32A and C1100TGX-1N24P32A: Line Numbering
GigaEthernet 0/0/0 to 0/0/11
Async 0/1/0 to Async 0/1/47
0 = 2-9
1 = 10-17
2 = 18-25
3 = 26-33
4 = 34-41
5 = 42-49
2
GigaEthernet 0/2/0 to 0/2/233
NIM 0/34
Fans, Ventilation and Airflow
Router and chassis temperature is regulated with internal fans. An onboard temperature sensor controls the
fan speed. The fans are always on when the router is powered on. Under most conditions, the fans operate at
the slowest speed to conserve power and reduce noise. When necessary, the fans operate at higher speeds
under conditions of higher ambient temperature.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
8
About Cisco 1100 Terminal Gateway Routers
Fans, Ventilation and Airflow

Figure 11: C1100TG-1N32A - Airflow
Figure 12: C1100TG-1N24P32A and C1100TGX-1N24P32A - Airflow
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
9
About Cisco 1100 Terminal Gateway Routers
Fans, Ventilation and Airflow

Specifications of Cisco 1100 Series Integrated Services Routers
For specifications on the Cisco 1100 Series ISRs, refer to the Cisco 1100 Terminal Gateway Routers
Specifications document.
Periodic Inspection and Cleaning
We recommend that you periodically inspect and clean the external surface of the router is recommended to
minimize the negative impact of environmental dust or debris. The frequency of inspection and cleaning is
dependent upon the severity of the environmental conditions, but we recommend a minimum once every six
months. Cleaning involves vacuuming router air intake and exhaust vents.
Sites with ambient temperatures consistently above 25°C or 77°F and with potentially high levels of dust or
debris might require periodic preventative maintenance cleaning.
Note
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
10
About Cisco 1100 Terminal Gateway Routers
Specifications of Cisco 1100 Series Integrated Services Routers

CHAPTER 2
Prepare for Router Installation
Before you install the Cisco 1100 Series Integrated Services Routers, you must prepare your site for the
installation. This chapter provides pre-installation information, such as recommendations and requirements
that should be considered before installing your router.
See the following sections to prepare for installation:
•Safety Recommendations, on page 11
•Safety With Electricity, on page 12
•Prevent Electrostatic Discharge Damage, on page 12
•General Site Requirements, on page 13
•NEBS Deployment Site Requirements, on page 14
•Rack Requirements, on page 15
•Router Environmental Requirements, on page 15
•Power Guidelines and Requirements, on page 16
•Network Cabling Specifications, on page 16
Safety Recommendations
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device. SAVE THESE INSTRUCTIONS
Statement 1071
Warning
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
11

Ultimate disposal of this product should be handled according to all national laws and regulations. Statement
1040.
Warning
Safety With Electricity
Only skilled person should be allowed to install, replace, or service this equipment. Refer to statement 1089
for description of skilled person. Statement 1090
Warning
Read the installation instructions before using, installing or connecting the system to the power source.
Statement 1004
Warning
This unit might have more than one power supply connection. To reduce risk of electric shock, all connections
must be removed to de-energize the unit. Statement 1028
Warning
Instructed person is someone who has been instructed and trained by a skilled person and takes the necessary
precautions when working with equipment. Skilled person/Qualified personnel is someone who has training
or experience in the equipment technology and understand potential hazards when working with equipment.
Statement 1089
Warning
Prevent Electrostatic Discharge Damage
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It can occur if electronic
printed circuit cards are improperly handled and can cause complete or intermittent failures. Always follow
ESD prevention procedures when removing and replacing modules:
• Ensure that the router chassis is electrically connected to ground.
• Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the clip to an
unpainted surface of the chassis frame to channel unwanted ESD voltages safely to ground. To guard
against ESD damage and shocks, the wrist strap and cord must operate effectively.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
12
Prepare for Router Installation
Safety With Electricity

• If no wrist strap is available, ground yourself by touching a metal part of the chassis.
For the safety of your equipment, periodically check the resistance value of the anti-static strap. It should be
between 1 and 10 megohms (Mohm).
Caution
General Site Requirements
To reduce risk of electric shock or fire, installation of the equipment must comply with local and national
electrical codes. Statement 1074
Warning
To reduce the risk of electric shock, the chassis of this equipment needs to be connected to permanent earth
ground during normal use. Statement 445
Warning
This product relies on the building’s installation for short-circuit (overcurrent) protection. To reduce risk of
electric shock or fire, ensure that the protective device is rated not greater than: 20A (AC), 5A (HVDC), 7A
(DC). Statement 1005
Warning
To reduce risk of electric shock and fire, a readily accessible two-poled disconnect device must be incorporated
in the fixed wiring. Statement 1022
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be accessed by
skilled, instructed or qualified personnel. Statement 1017
Warning
To reduce the risk of fire or bodily injury, do not operate it in an area that exceeds the maximum recommended
ambient temperature of: 40 °C Statement 1047
Warning
Site Selection Guidelines
The Cisco 1100 Series ISRs require specific environmental operating conditions. Temperature, humidity,
altitude, and vibration can affect the performance and reliability of the router. The following sections provide
specific information to help you plan for the proper operating environment.
The Cisco 1100 Series ISRs are designed to meet the industry EMC, safety, and environmental standards
described in the Regulatory Compliance and Safety Information for the Cisco 1100 Series ISR document.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
13
Prepare for Router Installation
General Site Requirements

NEBS Deployment Site Requirements
The NEBS GR-1089-CORE and GR-63-CORE compliance statements and requirements are listed in this
section. These statements only apply for deployments where NEBS compliance is mandated.
The intra-building port(s) (LAN, WAN, Serial, and T1 (NIM-xMFT-T1/E1 module)) of the equipment or
subassembly must use shielded intra-building cabling/wiring that is grounded at both ends. Statement 7003
Warning
The intra-building port(s) (LAN, WAN, Serial, and T1 (NIM-xMFT-T1/E1 module)) of the equipment or
subassembly is suitable for connection to intra-building or unexposed wiring or cabling only. The intra-building
port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect to the
OSP or its wiring for more than 6 meters (approximately 20 feet). These interfaces are designed for use as
intra-building interfaces only (Type 2, 4, or 4a ports as described in GR-1089) and require isolation from the
exposed OSP cabling. The addition of Primary Protectors is not sufficient protection in order to connect these
interfaces metallically to an OSP wiring system. Statement 7005
Warning
The AC power ports have been evaluated for deployments where an external Surge Protective Device (SPD)
is utilized at the AC power service equipment (see definition in National Electric Code). Statement 7012
Warning
This product is designed for a Common Bonding Network (CBN) installation. Statement 7013
Warning
This product can be installed in network telecommunication facilities or locations where the National Electric
Code applies. Statement 8015 and 8016
Warning
The DC return connection to this system should remain isolated from the system frame and chassis (DC-I).
Statement 7016
Warning
The following instructions and requirements are mandated for the C1100TG series when the NIM-LTEA-EA
module is installed in a NEBS deployment utilizing cables connected to outdoor antennas:
• Additional surge protection is required if an outdoor antenna is being connected to the GPS connector
and/or the LTE TNC connectors. The Lightning Protector must be able to provide a low clamping voltage
(less than 600V).
• Lightning protection must be mounted at the location where the antenna cable enters the building. The
primary lightning protection must be capable of conducting all potentially dangerous electrical energy
to PE (Protective Earth).
• Surge arrestors should support DC-pass and suitable for the frequency range with low attenuation.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
14
Prepare for Router Installation
NEBS Deployment Site Requirements

Rack Requirements
Cisco 1100 Terminal Gateway Routers includes brackets for use with a 19-inch rack and 23-inch rack.
The 23-inch rack mount brackets have not been evaluated for NEBS compliance. If 23-inch racks are being
used, 19-inch to 23-inch adapter plates compliant with GR-63-CORE Zone 4 waveforms must be used.
Note
The following information can help you plan your equipment rack configuration:
• Allow clearance around the rack for maintenance.
• Allowat least one rack unit of vertical space between routers; more clearance is required when stacking
multiple Cisco 1100 Terminal Gateway Routers. Provide adequate heat removal mechanism to keep the
surrounding air temperature well within the specified operating temperature condition.
More spacing may be required depending on the installation environment.
Note
• Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each router
generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air. Heat
generated by equipment near the bottom of the rack can be drawn upward into the intake ports of the
equipment above it.
• When mounting a chassis in an open rack, ensure that the rack frame does not block the intake or exhaust
ports. If the chassis is installed on slides, check the position of the chassis when it is seated in the rack.
Router Environmental Requirements
Cisco 1100 Terminal Gateway Routerscan be placed on a desktop or installed in a rack. The location of your
router and the layout of your equipment rack or wiring room are extremely important considerations for proper
operation. Equipment placed too close together, inadequate ventilation, and inaccessible panels can cause
malfunctions and shutdowns, and can make maintenance difficult. Plan for access to both front and rear panels
of the router.
When planning your site layout and equipment locations, refer to the General Site Requirements , section. If
you are currently experiencing shutdowns or an unusually high number of errors with your existing equipment,
these precautions and recommendations may help you isolate the cause of failure and prevent future problems.
• Ensure that the room where your router operates has adequate air circulation. Electrical equipment
generates heat. Without adequate air circulation, ambient air temperature may not cool equipment to
acceptable operating temperatures.
• Always follow ESD-prevention procedures described in the Preventing Electrostatic Discharge Damage
to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent
equipment failure.
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
15
Prepare for Router Installation
Rack Requirements

• Baffles can help to isolate exhaust air from intake air, which also helps to draw cooling air through the
chassis. The best placement of the baffles depends on the airflow patterns in the rack, which can be found
by experimenting with different configurations.
• When equipment installed in a rack (particularly in an enclosed rack) fails, try operating the equipment
by itself, if possible. Power off other equipment in the rack (and in adjacent racks) to allow the router
under test a maximum of cooling air and clean power.
Power Guidelines and Requirements
Check the power at your site to ensure that you are receiving power that is free of spikes and noise. Install
power conditioner if necessary.
Network Cabling Specifications
The following sections describe the cables and thee specifications required to install Cisco 1100 Series ISRs:
Console Port Connections
The Cisco 1100 Terminal Gateway Routers has EIA/TIA-232 asynchronous (RJ-45) and ASYNC ports. The
console port does not have any hardware flow control.
EIA/TIA-232
Depending on the cable and the adapter used, this port appears as a DTE or DCE device at the end of the
cable. Only one port can be used at the same time.
The default parameters for the console port are 9600 baud, 8 data bits, 1 stop bit, and no parity. The console
portdoes not support hardware flow control. For detailed information about installing a console terminal, see
the Connecting to a Console Terminal or Modem section.
For cable and port pinouts, see the Cisco Modular Access Router Cable Specifications document located on
Cisco.com.
Console Port Considerations
The router includes an asynchronous serial console port. The console ports provide access to the router using
a console terminal connected to the console port. This section discusses important cabling information to
consider before connecting the router to a console terminal or modem.
Console terminals send data at speeds slower than modems do; therefore, the console port is ideally suited
for use with console terminals.
Preparing for Network Connections
When setting up your router, consider distance limitations and potential electromagnetic interference (EMI)
as defined by the applicable local and international regulations.
Network connection considerations are provided for:
Hardware Installation Guide for the Cisco 1100 Terminal Gateway
16
Prepare for Router Installation
Power Guidelines and Requirements