Cisco 871 Safety guide

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Cisco Virtual Office – End User Instructions for
Cisco 871 and Cisco 881 Router Set Up at Home or
Small Office
Introduction
This document describes the end-user instructions to deploy the Cisco Virtual Office (CVO) for home or
small office use.
Cisco Virtual Office (CVO) solution offers a seamless home/small office experience comparable to
working in your company’s central office. CVO features support secure, always-on wired and wireless
(WLAN) data connectivity, voice services, and video capabilities.
Setup Your CVO Hardware
In this section you will be able to identify the basic hardware configuration needed to install the CVO
solution in your home/office. This is a known working configuration to assist you in your initial set-up
and is not intended to cover all variations of home/office network environments. This guide is written
based on Cisco 871 and Cisco 881 routers.
Ports on the CVO Router
It is important that you understand which ports on the back of your CVO router are used for what
purposes.
•FE0, FE1, FE2, and FE3: LAN Ports FE0 to FE3 are end-user device secure ports. Connect your
PC/Mac/Linux/IP phone equipment here.
•FE4: Use the WAN/FE4 port to connect your CVO router to your Internet Service Provider (ISP)
device.

2
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
SETUP YOUR CVO HARDWARE
How to Connect Your Equipment
This scenario shows an example of your company’s provided devices and the Internet Service Provider
(ISP) device (modem/router) properly connected to a CVO 871W router. The same ports should be used
to connect to a CVO Cisco 881W or non-wireless router.
For detailed descriptions, see below Step-by-Step Instructions.
Figure 1 End-to-end View of How Your Devices Should Connect Together

3
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Step-by-Step Instructions
Follow these steps to connect your CVO router to the ISP device and to your PC
Step 1 Make sure your ISP device (DSL modem, cable modem, etc) is plugged in and turned on. If your ISP
device is already on, power off your ISP device and wait 10 seconds. Remove the cables. Then power it
up and wait 30 seconds to complete the reset and reconnect your cables. Plug in your CVO router as
shown and power it up. Do not do any type of soft reboot on your ISP devices at this point.
Step 2 Plug the CVO router into the ISP modem/router using an Ethernet cable going from the Ethernet port on
the ISP device, to the WAN/FE4 port on the CVO router as shown in Figure 1.
Step 3 Plug your PC into the CVO router using the LAN trusted port FE0 as shown in Figure 1.
Configure Your Router
Once you have set up your CVO hardware you will need to configure your router so that you can access
the Internet and your company’s corporate network.
After the Internet connectivity is established you need to follow the steps that invoke the Secure Device
Provisioning (SDP) tool to communicate with your company’s core infrastructure and complete your
CVO router's configuration.
Internet Connectivity
The configuration needed to connect to the Internet is determined by the IP address assignment type.
DHCP Assignment
If you have a DHCP connection, your PC should already be able to access the Internet at this point, no
additional work is needed.
Other (PPPoE or Static) Assignment
If your IP address assignment type is anything other than DHCP some additional configuration is
needed to access the Internet. You must run the Cisco Configuration Professional Express (CCP Express)
tool and follow the steps to get the router connected to the Internet before you can proceed. You must
know what type of connectivity your ISP is providing you, typically PPPoE or static IP. Your ISP should
be able to give you this information. Go to “Appendix A: CCP Configuration” in this document and
follow the instructions to get internet access. Once done, return to the “Corporate Network
Connectivity” section and complete the SDP provisioning process.
Corporate Network Connectivity
Step 1 Test your Internet connection.
To double check that your PC is now connected to the Internet, open a browser window and type any
Internet website, for example, www.cisco.com.
Step 2 Initiate the Secure Device Provisioning (SDP) Process.

4
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
You will need to complete the process for Secure Device Provisioning (SDP) so that your CVO router
can access the corporate network and securely download its configuration.
If you are using Static addressing or PPPoE and used CCP Express for the initial configuration of your
router, specifying SDP for provisioning, then CCP Express will automatically direct you to the SDP
welcome page, where you have to authenticate using the login username/password that you configured
during the CCP Express setup (Figure 2).
Figure 2 SDP Authentication
If you’re using DHCP, to initiate the SDP process, go to the PC which is connected to the CVO router
and open a browser window. Then type in the address bar: http://10.10.10.1/ezsdd/welcome. You will be
prompted to authenticate, and you must use username/password cisco/cisco.

5
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
You will see the screen shown in Figure 3 while the router prepares for the rest of the SDP process.
Figure 3 SDP Screen
Step 3 Securely download the CVO router configuration.
When the screen refreshes you will notice a field for site URL. Enter the URL provided by your network
administrator (Figure 4).
Figure 4 URL Field
After you click Next you will see a Security Request confirmation window; select Yes to proceed.
Step 4 Authenticate yourself.
When the system attempts to connect to the corporate CVO management server, you are prompted to
authenticate yourself. You must use the credentials provided by your network administrator (Figure 5).

6
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Figure 5 Connect to SDP Server
When your authentication is accepted you will see the confirmation screen shown in Figure 6.
Figure 6 Confirmation Screen
Select Next to proceed.
Step 5 CVO router auto-configuration.
You should now see the enrollment window and your CVO router will automatically download the
configuration from the CVO management server (Figure 7).

7
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Note Do not select any of the options on this screen. This will interrupt your CVO router
configuration.
Please be patient during this process. This can take 5 or more minutes to complete. Any interruption will
cause an incomplete deployment.
Figure 7 Enrollment Window
Step 6 Verify that your CVO router has a VPN Light on in the front.
After 5 minutes, your router should have its VPN LED lit solid green.
At this point you need to have your PC register with the new router configuration to renew its IP address.
You have two options to renew your IP address:
a. restart your PC – this will automatically renew its IP address
b. (advanced users) right click on your network adaptor icon in the systray and click repair as show in
Figure 8:
Figure 8 Renew IP Address
Once you have a valid IP Address, open your browser and attempt to connect to an external Website.
This should be something other than your company’s internal home page; e.g. www.cisco.com.
If this is successful then proceed with testing an internal Website.
Step 7 Verify connectivity to your company’s corporate network.

8
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Once your CVO router’s configuration is complete you will be able to access your company’s internal
network via the VPN tunnels that have been created. Before you are allowed to access any internal
resources you will have to authenticate in accordance with your company’s corporate policy. Just open
a browser in the PC connected to the CVO router and type an internal Website of your company.
Congratulations! You are now ready to begin using your Cisco Virtual Office.
The CVO router will build a direct connection to the corporate network. Once the CVO router is installed
and configured, there is no need to run a VPN client or SSLVPN to be connected to your company
network.
Please refer to the CVO overview at www.cisco.com/go/cvo for further information about the solution,
its architecture, and all of its components.
For more details about the Cisco 800 Series Routers please visit
www.cisco.com/en/US/products/hw/routers/ps380/index.html.
For additional information about Cisco Configuration Professional (CCP), please visit
www.cisco.com/go/ciscocp.
Appendix A: CCP Configuration
To start configuring the CVO router with Cisco Configuration Professional Express (CCP Express) make
sure the PC is physically connected to CVO router on port FE0. Open an Internet browser and type
http://10.10.10.1. When prompted for username/password, please enter: cisco/cisco. CCP Express will
guide you to remove or configure a new username/password. The Cisco Configuration Professional
(CCP) Express wizards will guide you through the process of configuring your CVO router to connect
to the Internet, as described next.
1. Figure 9 shows the welcome screen of CCP Express. Click “Next” to start the wizard.

9
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Figure 9 Welcome Screen
2. Enter the desired login credentials and enable password, as well as the hostname and domain name
for the router (Figure 10), then click “Next”.

10
Cisco Virtual Office – End User Instructions for Cisco 871 and Cisco 881 Router Set Up at Home or Small Office
78-18858-01
CONFIGURE YOUR ROUTER
Figure 10 Basic Configuration
3. Specify “Secure Device Provisioning” as the method for provisioning the router, as SDP will be used
for the bootstrap config (Figure 11), then click “Next”