Cisco Linksys WET610N User manual

QUICK INSTALLATION GUIDE
Wireless-N Ethernet
Bridge with Dual-Band
Model: WET610N
Special Instructions for
Sony Bravia Owners
Please use this guide for
installation instructions,
and disregard the
contents of the Start Here
envelope in the Linksys
by Cisco package.
Package Contents
• Wireless-NEthernetBridge
withDual-Band
• SetupSoftwareandUserGuide
onCD-ROM
• QuickInstallationGuide
• NetworkCable
• PowerAdapter

TableofContentsWET610N
iWireless-NEthernetBridgewithDual-Band
Table of Contents
Overview1
1 PowerConnection2
2 SetupSelection2
Wi-FiProtectedSetup4
Scan(ManualSetup)7
Troubleshooting11

TableofContents WET610N
ii Wireless-NEthernetBridgewithDual-Band

OverviewWET610N
1Wireless-NEthernetBridgewithDual-Band
Overview
TheQuickInstallationGuidedescribeshowtocreateawirelessconnection
betweenyourwirelessrouterandyourSonyBraviaTV,soyourTVcan
accesstheInternetTheinstructionsexplainhowtoconnectandsetupthe
BridgeforusewithyourTV
Internet
Modem Router
Bridge
Office LivingRoom
TV
DiagramofaTypicalInstallation
List of Compatible TVs
TheLinksysbyCiscoBridgeiscompatiblewiththefollowing:
• Sony BRAVIA XBR9 Series LCD HDTVs
Models:KDL-40XBR9,KDL-46XBR9,KDL-52XBR9
• Sony BRAVIA Z Series LCD HDTVs
Models:KDL-40Z5100,KDL-46Z5100,KDL-52Z5100
• Sony BRAVIA W Series LCD HDTVs
Models:KDL-40W5100,KDL-46W5100,KDL-52W5100

PowerConnection WET610N
2Wireless-NEthernetBridgewithDual-Band
1 Power Connection
Checkthefollowing:1)makesurethatyoucanconnecttotheInternet
throughyourwirelessrouterandcomputer,and2)makesureyourTVis
poweredon
A. Plugtheincludedpower
adapterintothePowerportof
theBridge





B. Plugtheotherendofthepower
adapterintoanelectricaloutlet
(Yourpoweradaptermayvary
inappearance)
NOTE:Donotstackany
devicesontopofthe
Bridge;otherwise,they
mayinterferewithits
wirelessperformance
2 Setup Selection
A. AccessXMB,themenusystemofyourSonyBRAVIATVGoto
Settings > Network > Network Setup(Formoreinformationabout
howtouseXMB,refertothedocumentationforyourTV)
B. SelectWireless Bridge Setup
ThenselectContinue




SetupSelectionWET610N
3Wireless-NEthernetBridgewithDual-Band
C. Connectoneendofthe
includednetworkcabletothe
EthernetportoftheBridge
Thenconnecttheotherendto
theLANportoftheTV

SelectContinue
D. TheTVischeckingtheBridge
Pleasewait;thismaytakeafew
minutes



E. Youhaveachoiceoftwosetup
options:
Wi-Fi Protected Setup (WPS)
automaticsetup
Scan manualsetup
Wi-FiProtectedSetup(WPS)isa
featurethatmakesiteasytoset
upyourwirelessnetworkIfyour
routersupportsWi-FiProtected
Setup,thenitwillhaveabutton
thatlookslikeoneoftheicons
inthepicture
NOTE:IfyourrouterusesWEPsecurity,anencryptionmethod
thatisdesignedtohelpkeepyourdatasafe,foryourwireless
network,pleasenotethatWEPisnotsupportedbyWi-Fi
ProtectedSetup
IfyourroutersupportsWi-FiProtectedSetupandyouwanttousethis
option,selectWi-Fi Protected Setup (WPS)Thenselect Continue
ProceedtoWi-Fi Protected Setup,page 4
IfyourrouterdoesnotsupportWi-FiProtectedSetup,selectScanThen
select ContinueProceedtoScan (Manual Setup),page 7
Wi-FiProtectedSetupButtononRouter

Wi-FiProtectedSetup WET610N
4Wireless-NEthernetBridgewithDual-Band
Wi-Fi Protected Setup
Beforeyoubegin,makesuretheRouter’sWi-FiProtectedSetupfeatureis
enabledFormoreinformation,refertothedocumentationforyourrouter
A. SelectStartThenselect
Continue





B. Onyourrouter,pressthebutton
thatlookslikeoneoftheicons
inthepicture









C. TheBridgeisconnectingtothe
wirelessnetworkPleasewait;
thismaytakeafewminutes




Wi-FiProtectedSetupButtonontheRouter

Wi-FiProtectedSetupWET610N
5Wireless-NEthernetBridgewithDual-Band
D. Wi-FiProtectedSetupis
successfulTheBridgeis
configuredwiththewireless
settingsdisplayedon-screen
Select Continue


E. Tosetupthenetworksettings
oftheTV,selectAutoThen
select Continue




F. Thenewnetworksettingsare
displayedSelectContinueif
thesettingsarecorrect




G. Tosavethenewnetwork
settingsoftheTVandconnect
tothewirelessnetwork,select
Save & Connect





Wi-FiProtectedSetup WET610N
6 Wireless-NEthernetBridgewithDual-Band
H. TheTVisconnectingtothe
networkPleasewait;thismay
takeafewminutes




I. TheTVisconnectedto
thenetworkThestatusof
theBridge,localnetwork
connection,andInternet
connectionaredisplayedSelect
OKtoexitthisscreen

Congratulations! Setup is complete.
Ifyouencounteranyproblems,proceedtoTroubleshooting,page 11
NOTE:FormoreinformationabouthowtoinstalltheBridgefor
usewiththeSonyBRAVIATV,refertotheOnlineReferenceBook
foryourTV,andthensearchfortheNetwork SetupsectionFor
otherinformationabouttheBridge,refertotheUserGuideon
theCDincludedwiththeBridge

Scan(ManualSetup)WET610N
7Wireless-NEthernetBridgewithDual-Band
Scan (Manual Setup)
IMPORTANT:IfyouhaveusedWi-FiProtectedSetuptocreatea
wirelessconnectionbetweentheTVandBridge,thenyoudonot
needtofollowtheinstructionsintheManual Setup sectionYour
setupiscomplete
A. TheBridgeissearchingfor
availablewirelessnetworks
Pleasewait;thismaytakeafew
minutes



B. Ifyournetworkislisted,select
it,andthenselectContinue
ProceedtostepD

Ifyournetworkisnotlisted,
selectManual Entrytoenter
awirelessnetworkname(also
calledanSSID)Thenselect
Continue

Scan(ManualSetup) WET610N
8Wireless-NEthernetBridgewithDual-Band
C. SelectChangetodisplaythe
on-screenkeyboard

Usethenumberkeypadonyour
TV’sremotecontroltoenter
thenetworknameFordifferent
characters,pressthebutton
repeatedlyuntilyouseethe
desiredcharacters

Press ENTonyourTV’sremote
control,orselectConfirmto
savethenetworkname

SelectContinue








D. Ifyournetworkuseswireless
security,thenselectthe
appropriatesecuritymode:
WEP,WPA/WPA2-PSK (TKIP),
orWPA2-PSK (AES)(WPA-or
WPA2-PSKisalsoknownas
WPA-orWPA2-Personal)Select
ContinueProceedtostepE
Ifyournetworkdoesnotusesecurity,thenselectNoneSelect
ContinueProceedtostepF
NOTE:WPA-AESisnotsupportedIftherouterusesWPA-AES
forsecurity,thenpleasechangethissettingontherouterand
yourotherwirelessdevicesFormoreinformation,refertothe
documentationforyourrouter

Scan(ManualSetup)WET610N
9Wireless-NEthernetBridgewithDual-Band
E. SelectChangetodisplaythe
on-screenkeyboard

Usethenumberkeypadonyour
TV’sremotecontroltoenter
thesecuritykeyFordifferent
characters,pressthebutton
repeatedlyuntilyouseethe
desiredcharacters

Press ENTonyourTV’sremote
control,orselectConfirmto
savethesecuritykey

SelectContinue








F. Tosetupthenetworksettings
oftheTV,selectAutoThen
select Continue




G. Thenewnetworksettingsare
displayedSelectContinueif
thesettingsarecorrect





Scan(ManualSetup) WET610N
10 Wireless-NEthernetBridgewithDual-Band
H. Tosavethenewnetwork
settingsoftheTVandconnect
tothewirelessnetwork,select
Save & Connect




I. TheTVisconnectingtothe
networkPleasewait;thismay
takeafewminutes




J. TheTVisconnectedto
thenetworkThestatusof
theBridge,localnetwork
connection,andInternet
connectionaredisplayedSelect
OKtoexitthisscreen

Congratulations! Setup is complete.
Ifyouencounteranyproblems,proceedtoTroubleshooting,page 11
NOTE:FormoreinformationabouthowtoinstalltheBridgefor
usewiththeSonyBRAVIATV,refertotheOnlineReferenceBook
foryourTV,andthensearchfortheNetwork SetupsectionFor
otherinformationabouttheBridge,refertotheUserGuideon
theCDincludedwiththeBridge

TroubleshootingWET610N
11Wireless-NEthernetBridgewithDual-Band
Troubleshooting
Ifyouencounteranyproblemsduringtheinstallationprocess,pleasetry
thesolutionsforyourproblem
The Bridge is not found.
1 Followtheseinstructionsuntil
yourproblemissolved:
•MakesuretheBridgeis
poweredon
•Makesurethenetwork
cableissecurely
connectedtotheBridge
andTV
•DisconnectthepoweradapterfromtheBridgeWaitfiveseconds
ThenconnectthepoweradaptertotheBridge
•ResettheBridgetoitsfactorydefaultsettingsUsinganobjectwitha
smalltip,suchasapen,pressandholdtheBridge’sResetbuttonfor
approximatelyfiveseconds(TheResetbuttonislocatedbetween
theEthernetandPowerports)
2 OntheTV,selectRETURNtotryagain
The TV has lost its connection
to the Bridge.
1 Followtheseinstructionsuntil
yourproblemissolved:
•MakesuretheBridgeis
poweredon
•MakesurethenetworkcableissecurelyconnectedtotheBridge
andTV
•DisconnectthepoweradapterfromtheBridgeWaitfiveseconds
ThenconnectthepoweradaptertotheBridge
•ResettheBridgetoitsfactorydefaultsettingsUsinganobjectwitha
smalltip,suchasapen,pressandholdtheBridge’sResetbuttonfor
approximatelyfiveseconds(TheResetbuttonislocatedbetween
theEthernetandPowerports)
2 OntheTV,selectRETURNtorestarttheNetworkSetupprocess

Troubleshooting WET610N
12 Wireless-NEthernetBridgewithDual-Band
The Bridge cannot be accessed.
Followtheseinstructions:
1 ResettheBridgetoitsfactory
defaultsettingsUsinganobject
withasmalltip,suchasapen,
pressandholdtheBridge’sReset
buttonforapproximatelyfive
seconds(TheResetbuttonis
locatedbetweentheEthernet
andPowerports)
2 OntheTV,selectRETURNtorestarttheNetworkSetupprocess
No wireless networks are
detected by the Bridge.
Followtheseinstructionsuntil
yourproblemissolved:
•SelectBacktorepeatthe
searchforwirelessnetworks
Repeatthesearchuntilyour
wirelessnetworkisdetected
•SelectManual Entrytoenterthenameofyourwirelessnetwork(also
calledanSSID)ThenselectContinueProceedtotheinstructionsinthe
Scan (Manual Setup)section,stepC,onpage8
NOTE:FormoreinformationabouthowtoinstalltheBridgefor
usewiththeSonyBRAVIATV,refertotheOnlineReferenceBook
foryourTV,andthensearchfortheNetwork SetupsectionFor
otherinformationabouttheBridge,refertotheUserGuideon
theCDincludedwiththeBridge

NotesWET610N
13Wireless-NEthernetBridgewithDual-Band

Notes WET610N
14 Wireless-NEthernetBridgewithDual-Band
09072110NC-JL

FormoreinformationabouthowtoinstalltheBridgeforusewiththeSonyBraviaTV,refer
totheOnlineReferenceBookforyourTV,andthensearchfortheNetwork Setupsection
ForotherinformationabouttheBridge,refertotheUserGuideontheCDincludedwith
theBridge
Sony Website
http://www.sony.com
Linksys by Cisco
http://www.linksysbycisco.com
© 2009 Cisco Systems, Inc. All rights reserved. Cisco, the Cisco logo,and Linksys are trademarks or registered trademarks of Cisco Systems, Inc.and/
or its affiliates in the United States and certain other countries.All other trademarks mentioned in this document or website are the property of
their respective owners.The use of the word partner does not imply a partnership relationship between Cisco and any other company.
3435-00546