Cisco 1005 Installation guide

CHAPTER
Overview of the Cisco 1005 1-1
Overview of the Cisco 1005
1
The Cisco 1005 router is a small desktop router that links small remote sites with Ethernet
LANs to regional and central offices through WAN connections.
Features The router includes the following features:
•One Ethernet 10BaseT port (RJ-45)
•One console port (RJ-45)
•One serial port (DB-60) that supports the following types of WAN communications:
—Permanent and switched synchronous WAN links at speeds up to 2.048 Mbps
—EIA/TIA-232 asynchronous WAN links at speeds up to 115.2 kbps
•One slot for an optional Personal Computer Memory Card International Association
(PCMCIA) Flash memory card
•Software boot using Trivial File Transfer Protocol (TFTP) over an Ethernet LAN
connection or by using the optional Flash memory card
•Internet Protocol (IP), Internetwork Packet Exchange (IPX), and AppleTalk routing
•Transparent bridging, which supports protocols that cannot be routed
•Support for the following WAN encapsulations: Point-to-Point Protocol (PPP),
High-Level Data Link Control (HDLC), Link Access Procedure Balanced (LAPB),
Frame Relay, Switched Multimegabit Data Service (SMDS), and X.25

1-2 Cisco 1005 User Guide
Features
•Routermanagementthroughtheconsoleportorover the networkusingSimpleNetwork
Management Protocol (SNMP) or Telnet
•AutoInstall for downloading configuration files automatically over a WAN
Figure 1-1 illustrates the Cisco 1005 router.
Figure 1-1 Front View of the Cisco 1005
H4203

Overview of the Cisco 1005 1-3
Features
Figure 1-2 illustrates a typical internetwork using the Cisco 1005 router.
Figure 1-2 Example of the Cisco 1005 in a Network
1005
H3829
Regional office
Cisco 4000 Regional office
Cisco 4500
Headquarters
Cisco 7000 Internet
1005 1005
X.25
T1/E1
leased lines
Frame Relay
1005 1005
1005
Switched 56
1005
Switched
Multimegabit
Data Service

1-4 Cisco 1005 User Guide
Specifications
Specifications
The specifications of the router are listed in Table 1-1.
Table 1-1 System Specifications
1. DRAM = dynamic random-access memory.
2. SIMM = single in-line memory module.
3. PROM = programmable read-only memory.
4. NVRAM = nonvolatile random-access memory.
5. The serial port supports the following synchronous interfaces: EIA/TIA-232, EIA/TIA-449, V.35, X.21,
and EIA-530. The serial port supports EIA/TIA-232 asynchronous interfaces.
6. EIA/TIA-232 and EIA/TIA-449 were known as recommended standards RS-232 and RS-449 before their
acceptance as standards by the Electronic Industries Association (EIA) and Telecommunications Industry
Association (TIA).
Description Specification
Dimensions (H x W x D) 1.75 x 8.0 x 8.3" (4.4 x 20.3 x 21.1 cm)
Weight 2.6 lb (1.2 kg)
Input voltage, frequency,
and power dissipation 12 VDC output, minimum 0.5A External power supply: 100–240 VAC at 50–60 Hz, 1.0A input
Memory 4-MB DRAM1SIMM2
1-MB boot PROM3
8-KB NVRAM4
WAN interface 1 serial (DB-60)5
Ethernet interface 1 10BaseT (RJ-45)
PCMCIA slot 1 Type 2 (for Flash ROM card)
Console interface 1 asynchronous serial (EIA/TIA-2326) (RJ-45)
Operating environment 32–104°F (0–40°C)
Operating humidity 10–90%, noncondensing
Agency compliance FCC Class B, VCCI Class 2, CISPR-22 Class B,
EN 55022 Class B

Overview of the Cisco 1005 1-5
VCCI Class 2 Compliance Statement
VCCI Class 2 Compliance Statement
This equipment is in the 2nd Class category (information equipment to be used in a
residential area or adjacent area thereto) and conforms to the standards set by the Voluntary
Control Council for Interference by data processing equipment and electronic office
machines aimed at preventing radio interference in such residential area. When used near a
radio or TV receiver, it may become the cause of radio interference. Read the instructions
for correct handling.

1-6 Cisco 1005 User Guide
VCCI Class 2 Compliance Statement