Cisco 897VAW User manual

1-108
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-67 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW routers.
Figure 1-67 Front Panel of the Cisco 897VAW and the Cisco 897VAMW Routers
Figure 1-68 shows the back panel of the Cisco 897VAMW Router.
Figure 1-68 Back Panel of the Cisco 897VAMW Router
1
344770
1LEDs
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
54VDC 1.2A
12VDC 2.5A
VDSL/ADSL
overPOTS
CONSOLE
RESET
344772
11
1 2 3 4 7 89 10
5 6
1GE WAN interface 7On/Off switch
2SFP port 8Reset button
3USB port 9Earth ground connection
48-port Gigabit Ethernet switch110 Kensington security slot
5Console/Auxiliary port 11 VDSL / ADSL over POTS
6Power connector
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.

1-109
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Figure 1-69 shows the back panel of the Cisco 898EA router.
Figure 1-69 Back Panel of the Cisco 898EA Router
Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non-RJ-45 connector is inserted.
Figure 1-70 shows the front panel of the Cisco 898EA Router.
Figure 1-70 Front Panel of the Cisco 898EA Router
7 6 GELAN 5 4
3 2 POE 1 0
8
GE WAN
SFP
854VDC 1.2A
12VDC 2.5A
SHDSL
RJ45 ONLY
CONSOLE
RESET
Cisco 898EA
AUX
344774
11
1 2 3 4 7 89 10
5 6
1GE WAN interface 7On/Off switch
2SFP port 8Reset button
3USB port 9Earth ground connection
48-port Gigabit Ethernet switch1
1. Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured with
the factory order, you must order and install it to enable the PoE function.
10 Kensington security slot
5Console/Auxiliary port 11 SHDSL (RJ45 only)
6Power connector
1
344773
1LEDs

1-110
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Cisco C897VAB-K9
The Cisco 897VAB-K9 ISR is designed tosupport 2-pair VDSL2 bonding up to the 17a profile and single
pair support for ADSL/VDSL over POTS up to the 30a profile.
Table 1-38 provides information about important hardware specifications pertaining to Cisco
C897VAB-K9 ISR.
Figure 1-71 shows the back panel of the Cisco 897VAB-K9 ISR.
Figure 1-71 Back panel of the Cisco 897VAB-K9 ISR
Table 1-38 Hardware Specifications of Cisco C897VAB-K9 ISR
Hardware Description
Flash Memory 256 MB
Main Memory 1-GB DDR RAM; fixed and not extendable
USB port A USB 2.0-compliant port located on the back
panel
FAN Fanless chassis
PoE (Optional) Four internal PoE ports
Primary WAN VDSL/ADSL over POTS
Backup WAN 10/100/1000 GE port (RJ-45/SFP)
Console or auxiliary port RJ-45
LAN switch 8-port 10/100/1000 GE Switch
ISDN
over POTS,VDSL
364228
1 2 3 4 5 6 7 10 121189
B
1Primary WAN VDSL / ADSL over POTS,
VDSL2 Bonding17Console/Auxiliary Port
2SFP port 8Power Connector
3GE WAN Interface 9On/Off Switch
4ISDN 10 Reset Button
5USB Port 11 Earth Ground connection
68-port Gigabit Ethernet Switch212 Kensington Security slot

1-111
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Caution The primary WAN port is designed for an RJ-11 or RJ-14 connector only. Damage to the
primary WAN port may occur if a non-RJ-11 or RJ-14 connector is inserted.
Figure 1-72 shows the front panel of the Cisco 897VAB-K9 ISR.
Figure 1-72 Front panel of the Cisco 897 VAB-K9 ISR
Table 1-39 describes the LEDs for the Cisco 897VAB-K9 ISR.
1. 1.ADSL and VDSL (up to 17a) single-pair functionality uses the center pair of pins in the RJ-11 connector. VDSL 30a single
pair functionality makes use of the pins just adjacent to the center pins. VDSL Bonding makes use of both the center pair pins
& those just adjacent to the center pair to provide the 2 bonded VDSL lines. For more information, see Cisco 890 Series
Integrated Services Routers Data Sheet.
2. 2.Ports 0 through 3 can be configured as POE, which is an optional feature for this model. If this feature is not configured
with the factory order, you must order and install it to enable the PoE function.
364227
CD0 CD1 B1 B2
ISDN
1 3
24
5
6
7
8
9
Table 1-39 LED Descriptions for the Cisco 897VAB-K9 ISR
Number LED Color Description
1 Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Boot up is in process, or the router is in ROM
Monitor (ROMMON) mode.
Off—Power is not supplied to the router.
2 PoE OK Green/Yellow Off—Both POE card & POE power supply are not
present.
Yellow On—Either POE card or POE power supply is
not present.
Green On—Both POE card & POE power supply are
present.

1-112
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
3 GE LAN 0
GE LAN 1
GE LAN 2
GE LAN 3
Green/Yellow Off—No link.
Green On—Link.
Yellow On—Fault with PoE. Implies no link.
Green Blinking—Data is either being received or
transmitted.
4 GE LAN 4
GE LAN 5
GE LAN 6
GE LAN 7
Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
5 GE WAN 8 Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
SFP WAN 8 Green Off—No link.
On—Link.
Blinking—Data is either being received or being
transmitted.
6 VPN Green Off—No tunnel.
On—At least one tunnel is up.
7 PPP Green Off—No PPP session.
On—At least one PPP session established.
8 xDSL CD0 Green Off—Interface is shutdown.
On—Showtime, Link up.
Slow Blinking—Modem initialization.
Fast Blinking—Training up the line.
If both CD0 & CD1 are ON then VDSL Bonding is
active.
xDSL CD1
xDSL DATA Green Off—No Data.
Blinking—Data is either being received or transmitted.
9 ISDN B1 Green Blinking—Data is either being received or transmitted.
Off—No Data.
ISDN B2
Table 1-39 LED Descriptions for the Cisco 897VAB-K9 ISR (continued)
Number LED Color Description

1-113
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Cisco C891 Series ISRs
Cisco C891 Series ISRs are designed to deliver secure broadband, metro Ethernet, wireless LAN
(WLAN) connectivity, and business continuity. Cisco C891 Series ISRs also provide a 1-port Gigabit
Ethernet SFP socket for WAN connectivity.
This section includes the hardware information for the following models:
•Cisco C891F
•Cisco C891FW
Table 1-40 provides information about the hardware specifications of the Cisco C891 Series Routers.
For detailed hardware specifications, see the Cisco C890 Series hardware data sheet at:
http://www.cisco.com/en/US/prod/collateral/routers/ps380/data_sheet_c78-519930.html
Cisco C891F Router
Figure 1-73 shows the front panel of the Cisco C891F Router.
Table 1-40 Hardware Specifications of Cisco C891 Series ISR
Hardware Description
Flash Memory 256 MB
Main Memory 1-GB DDR RAM; fixed and not extendable
USB port A USB 2.0-compliant port located on the back
panel
FAN Fanless chassis
PoE 4 PoE ports
WAN 1-port GE or 1-port SFP
Data Backup •1-port FE
•1-port ISDN
•1-port V.92
Console or auxiliary port RJ-45
LAN switch 8-port Gigabit Ethernet
Embedded Wireless AP Dual 802.11b/g/n and 802.11a/n radios for
C891FW

1-114
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-73 Front Panel of the Cisco C891F Router
For detailed description about the LEDs on the Cisco C890 Series Routers, see the “LEDs” section on
page 1-25.
361136
Cisco
Cisco 800
Series
OK
OK
P
OE
OE
PPP
PPP
GE
GE LAN
VPN
V.92
V.92
ISDN
ISDN
OK
OK 01 2 3 4 567
GE8
GE8
SFP8
SFP8
FE0
FE0
WAN
WAN
B1
B1
B2
B2
P
OE
OE
1
1LEDs

1-115
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Figure 1-74 shows the back panel of the Cisco C891F Router.
Figure 1-74 Back Panel of the Cisco C891F Router
For information on installing the Cisco C890 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
Cisco C891FW Router
Figure 1-75 shows the front panel of the Cisco C891FW Router.
Figure 1-75 Front Panel of the Cisco C891FW Router
For detailed description about the LEDs on Cisco C890 Series Router, see “LEDs” section on page 1-25.
361137
FE
FE W
AN
AN
ISDN
ISDN
GE
GE W
AN
AN
SFP
SFP
V
.92
.92
7 6
GE
GE L
AN
AN
C
ON
ONS
OLE
OLE
Ci
Cisco
89
891F
RES
RESET
A
UX
UX
5 4
3 2
POE
POE 10
00
8 8
0
54V
54VDC 1
.5A
.5A
3.5-5A
3.5-5A
12V
12VDC
(POE)
(POE)
1 2 3 4 5 7 813129 11
10
6
1Back up WAN port—FE WAN 8Console/Auxiliary port
2ISDN 9Power connector
3Primary WAN port—GE WAN 10 On/Off switch
4SFP 11 Reset button
5USB port 12 Earth ground connection
6V.92 backup 13 Kensington security slot
78-port 10/100/1000 Ethernet switch
361138
OK
POE
PPP
GE LAN
VPN V.92
ISDN
OK 0 1234567GE8SFP8FE0 5GHz
2.4GHz
WAN
B1 B2
POE
Cisco 800 Series
1
1LEDs

1-116
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-76 shows the back panel of the Cisco C891FW Router.
Figure 1-76 Back Panel of the Cisco C891FW Router
For information on installing the Cisco C890 Series Routers, see:
http://www.cisco.com/en/US/docs/routers/access/800/860-880-890/hardware/installation/guide/2Instal
l880-860.html
361139
FE
FE W
AN
AN
ISDN
ISDN
GE
GE W
AN
AN
SFP
SFP
V
.92
.92
7 6
GE
GE L
AN
AN
C
ON
ONS
OLE
OLE
Ci
Cisco
89
891
FW
FW
RES
RESET
A
UX
UX
5 4
3 2
POE
POE 10
00
8 8
0
54V
54VDC 1
.5A
.5A
3.5-5A
3.5-5A
12V
12VDC
(POE)
(POE)
1 2 3 4 5 7 813129 11
10
6
1Back up WAN port—FE 8Serial port—Console or auxiliary
2ISDN 9Power connector
3Primary WAN port—GE 10 On/Off switch
4SFP port 11 Reset button
5USB port 12 Earth ground connection
6V.92 backup port 13 Kensington security slot
78-port 10/100/1000 Ethernet switch

1-117
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Cisco C891-24X/K9 Integrated Services Router
Cisco C891-24X/K9 Integrated Services Router (ISR) is a fixed Cisco 890 Series ISR that supports 24
port GE LAN. Cisco C891-24X/K9 ISR provides more switch port options compared to other 890 Series
ISRs and Cisco C891-24X/K9 ISR is useful in deployment scenarios where more switching capability
is required. Cisco C891-24X/K9 ISR also supports PoE on 8 switch ports. Cisco C891-24X/K9 ISR
supports WAN connectivity through dual GE or SFP ports.
Table 1-41 provides information about important hardware specifications pertaining to Cisco
C891-24X/K9 ISR.
Figure 1-77 shows the front panel of the Cisco C891-24X/K9 ISR.
Figure 1-77 Front Panel of the Cisco C891-24X/K9 ISR
Table 1-41 Hardware Specifications for Cisco C891-24X/K9 ISR
Hardware Description
Flash Memory 256 MB Flash and 8 MB serial boot flash
Main Memory 1-GB DDR RAM
USB port A USB 2.0-compliant port located at the back
panel
PoE 8 PoE ports
WAN 2-port GE WAN (copper or SFP)
Console or auxiliary port RJ-45
LAN switch 24-port 10/100/1000 BASE-T
Fan Fan less Chassis
POWER

1-118
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Figure 1-78 shows the back panel of the Cisco C891-24X/K9 ISR.
Figure 1-78 Back Panel of the Cisco C891-24X/K9 ISR
For information on installing the C891-24X/K9 ISR see the following link:
http://www.cisco.com/c/en/us/td/docs/routers/access/800/hardware/installation/guide/800HIG/installin
g.html
Hardware Features
This section provides an overview of the following hardware features for the Cisco 860 Series, 880
Series, and 890 Series ISRs. A feature summary is available at the end of this section.
•Kensington Lock
•Reset Button
•LEDs
•Memory
•USB Port
•Fan
•Power Supply
•Power over Ethernet Module
•3G Cellular Data WAN Connectivity
•Small Form-Factor Pluggable Port
•Feature Summary
364240
SYSTEM
Cisco C891-24X
POE Enabled GE LAN
1 2 3 4 5 89 10 116 7
1Console or auxiliary port 7SFP port
2Reset Button 8GE WAN port
3USB port 9SFP port
4PoE enabled GE LAN ports 10 System LED
5GE LAN ports 11 Kensington security slot
6GE WAN port

1-119
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Kensington Lock
A Kensington security slot is located on the router back panel. To secure the router to a desktop or other
surface, use the Kensington lockdown equipment.
Reset Button
The Reset button is used to restore the router to the factory default configuration or to load a custom
configuration file.
There are two different ways to do this:
•By pressing the Reset button within 5 seconds of powering up the router.
•By pressing the Reset button for 5 seconds while running IOS software.
Note If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified
Wireless Network software, the router reboots, but the AP continues to run. Clients with Cisco Unified
Wireless Network software are controlled by a wireless LAN controller (WLC) and can be reset only by
the controller.
Cisco 860VAE Routers—Custom Configuration File
On the Cisco 860VAE routers, the reset button can be used to load a custom configuration file without
having to use the CLI. The configuration file can be located on an external USB flash drive or on the
router's compact flash.
The custom configuration file must be named one of the following:
•customer-config
•SN-customer-config (where “SN” is the unique hardware serial number)
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the SN-customer-config file name
has priority over the customer-config file name. The priority for loading a configuration file is as
follows:
1. USB flash0—SN-customer-config
2. USB flash0—customer-config
3. Router flash—SN-customer-config
4. Router flash—customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router to the factory default configuration, follow these steps:
Step 1 Verify that Cisco IOS is running correctly by checking that the system status LED is on.

1-120
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
Custom Configuration File for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
In the first method, the configuration file can be located on the router's compact flash or on the router's
NVRAM. The custom configuration file must use cfg as the filename extension.
When the system attempts to load a custom configuration file, configuration files on NVRAM have
priority over configuration files on the router's compact flash.
The priority for loading a configuration file is as follows:
1. nvram: *.cfg
2. Router flash: *.cfg
If the router does not find a valid custom configuration file, the system aborts the process.To reset the
router to the factory default configuration or to load a custom configuration file, follow these steps:
Step 1 Turn the power on.
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
In the second method, the configuration file can be located on an external USB flash drive or on the
router's compact flash.
The custom configuration file must be named one of the following:
•customer-config
•customer-config.SN, where "SN" is the unique hardware serial number.
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the "customer-config.SN" file name
has priority over the customer-config file name.
The priority for loading a configuration file is as follows:
1. usbflash0:customer-config.SN
2. usbflash0:customer-config
3. Router flash:customer-config.SN
4. Router flash:customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router tothe factorydefault configuration or to load a custom configuration file, follow these
steps:
Step 1 Verify that Cisco IOS is running correctly by checking that the system status LED is on.

1-121
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
LEDs
The LEDs are located on the front panel of the router.
•Table 1-42 describes the LEDs for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series
ISRs.
•Table 1-43 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
Cisco 867VAE-K9 ISRs.
•Table 1-44 lists the LED description for the Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco
898EA ISRs.
•For a description of LEDs for Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco
860VAE-POE-W-A-K9 ISRs models, see the “Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9,
and Cisco 860VAE-POE-W-A-K9 ISRs” section on page 1-42.
Table 1-42 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
LED Color Description 860 Series 880 Series 890 Series
Power OK Green On—DC power is being supplied to the router and the
Cisco IOS software is running.
Blinking—Bootup is in process, or the router is in
Rommon monitor mode.
Off—Power is not supplied to the router.
All models All models All models
Link Status FE0 Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
All models All models All models
Link Status FE1
Link Status FE2
Link Status FE3
Link Status FE4 Green On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
— — All models
Link Status FE5
Link Status FE6
Link Status FE7
FE WAN Port
Link Status Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
861
models 881 models All models
GE WAN Port
Link Status Green On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
— — All models

1-122
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
WLAN
(2.4 GHz) Green On—Radio is connected, SSID1is configured, and client is associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
Wireless
models Wireless models Wireless models
WLAN (5 GHz) Green On—Radio is connected, SSID is configured, and client is
associated, but no data is being received or being
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
— Wireless
models Wireless models
WLAN LINK
(Autonomous
Mode)
Green On—Wireless link is up.
Blinking—Ethernet link is up, and data is either being
received or being transmitted.
Off—Wireless link is down.
Wireless
models Wireless models Wireless models
WLAN LINK
(Unified Mode) Green On—Ethernet link isup, and wireless access point (AP) is communicating with LWAPP2controller.
Blinking—Ethernet link is up, but wireless AP is not
communicating with LWAPP controller.
Off—Ethernet link is down.
— Wireless
models Wireless models
PoE Green On—PoE is connected and powered.
Off—PoE is not installed.
—Models
with PoE Models with PoE
Amber On—Fault with the PoE.
VPN Green On—VPN is connected. — All models All models
PPP3Green On—At least one PPP session is established. — All models All models
xDSL4CD Green On—The xDSL interface is connected to the DSLAM5.
Blinking—Training to the line.
Off—Indicates that a connection has not been established
or the port is shut down.
— 886,
886VA,
887,
887VA,
887VA-M
888
models
896VA,
897VA,
898EA,
897VAB
Table 1-42 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series

1-123
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
xDSL Data Green Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
— 886,
886VA,
887,
887VA,
887VA-M
888
models
896VA,
897VA,
898EA,
897VAB
xDSL ATM Green On—The router is operating in ATM6mode.
Off—Not operating in ATM mode.
— 888E —
xDSL EFM Green Blink—The router is operating in EFM7mode.
Off—Not operating in EFM mode.
— — 898EA
Data BRI LINK Green On—ISDN D channel is connected. — 887, 888
models 892 models
Data BRI B1 Green Blinking—B1 channel is either receiving or sending data,
or data is passing through ISDN channel 1. — 887, 888 models 892 models
Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or
data is passing through ISDN channel 2. — 887, 887V, 888
models
892
models
3G8WWAN9Green On—Service is established.
Slow Blinking—Searching for service.
Fast Blinking—Data is either being received or being
transmitted.
— 3G models —
3G RSSI10 Green Off—Low signal strength (lower than -100 dBm).
On—High RSSI (-69 dBm or higher).
Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
Fast Blinking—Medium RSSI (-89 to -70 dBm).
— 3G models —
Amber On—No service. — 3G models —
3G GSM11 Green On—Service is established.
Off—No service.
— 3G models —
3G CDMA12 Green On—Service is established.
Off—No service.
— 3G models —
FXO Voice Green On—FXO port is connected.
Blinking—FXO port is either receiving or transmitting
data.
— 88113 —
BRI Voice LNK Green On—BRI interface is connected. — — —
BRI Voice B1 Green On—BRI B1 channel is connected.
Blinking—BRI B1 channel is either receiving or
transmitting data.
———
Table 1-42 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series

1-124
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-43 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco
867VAE-K9 ISRs.
BRI Voice B2 Green On—BRI B2 channel is connected.
Blinking—BRI B2 channel is either receiving or
transmitting data.
———
FXS/DID Voice Green On—FXS/DID port is connected.
Blinking—FXS/DID port is either receiving or
transmitting data.
—SRST
models —
V.92 Modem Green On—Modem is connected.
Blinking—V.92 port is either receiving or transmitting
data.
— — 891
models
SFP14 EN Off Not present. — — 892F
models
Green Present and enabled. — —
Amber Present with failure. — —
SFP S Green Blinking—Blinking frequency indicates port speed. — — 892F
models
1. SSID = service set identifier.
2. LWAPP = Lightweight Access Point Protocol.
3. PPP = Point-to-Point Protocol.
4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
subscriber line).
5. DSLAM = digital subscriber line access multiplexer.
6. ATM = Asynchronous Transfer Mode.
7. EFM = Ethernet in the First Mile.
8. 3G = Third-Generation.
9. WWAN = wireless WAN.
10. RSSI = Received Signal Strength Indicator.
11. GSM = Global System for Mobile Communication.
12. CDMA = code division multiple access.
13. SRST = Survivable Remote Site Telephony.
14. SFP = small-form-factor pluggable.
Table 1-42 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED Color Description 860 Series 880 Series 890 Series

1-125
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Table 1-43 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs
LED Activity Description
Power/System Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Off
Power is on and system running in the ROMMON mode.
Note During the early booting stage, both Power/System, GE_MODE, and
DSL_LINK LED will be turned on temporarily for the power on test.
DSL_LINK and GE_MODE LED will be turned off later after booting
into ROMMON.
Power/System LED: Solid
GE_MODE LED: Solid
DSL_LINK LED: Off
Cisco IOS functioning in GE WAN mode.
Power/System LED: Solid
GE_MODE LED: Off
DSL_LINK LED: Solid or
flashing
Cisco IOS functioning in DSL_WAN mode.
Note In Cisco IOS DSL_WAN mode, DSL_LINK LED will be solid after
DSL training complete or flashing during training.
xDSL1ACT
1. xDSL = General term referring to various forms of DSL, includi\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
ng ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line).
Green On—DSL interface is up.
Blinking—DSL WAN activity (traffic in either direction).
Faster blinking—Heavier traffic
Off—Device is powered off or the DSL WAN interface is down.
xDSL Link Green On—DSL WAN Mode is selected and DSL training complete.
Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,
such as in-training, or controller “OFF,” or no cable attached to DSL connector.
Off—Device is powered off or GE WAN mode is selected.
GE ACT Green On—GE WAN interface is up.
Blinking—GE WAN activity (traffic in either direction).
Off—Device is powered off or GE WAN interface is down.
GE Mode Green On—GE WAN Mode is selected.
Off—Device is powered off or DSL WAN mode is selected.

1-126
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview
Cisco 860, 880, 890 Series
Table 1-44 describes the LEDs for the Cisco 892FSP.
Table 1-44LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers
Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers
On the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W routers, the BRI1, BRI2 and the FXS ports
share LED indicators. The following ports share an LED indicator:
•BRI 1B1 channel and FXS 3
•BRI 1B2 channel and FSX 4
•BRI 2B1 channel and FXS 5
•BRI 2 B2 channel and FXS 6
LED Color Activity Description
PWR_OK Green Power Status Off—No power.
Steady on—Normal operation.
Blink—Boot up phase or in ROM Monitor mode.
GE0 Green/Amber Link Status Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with
the inline power supply.
Green/Amber Blinking—Data is either being
received or being transmitted.
Green/Amber Off—Ethernet port is not
connected.
GE1
GE2
GE3
GE4
GE5 Green Link Status On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Ethernet port is not connected.
GE6
GE7
GE WAN ports Green Link Status On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
SFP WAN
ports Green Link Status On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
VPN_OK Green — Off—No tunnel.
Steady on—At least one tunnel is up.
PPP_OK Green — Off—No PPP session.
Steady on—At least one PPP established.

1-127
Cisco Integrated Services Router Hardware Installation Guide
Chapter 1 Product Overview Cisco 860, 880, 890Series
Because the LED indicators are shared, the LED illuminates (green) when either port is active. For
example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or
when the FXS port is active. You can determine the activity status on each interface by using the
following commands.
•For activity status on the FXS ports, use the show port summary command.
•For activity status on the BRI ISDN port, use the show isdn status command.
Figure 1-79 shows a close-up view of the LED indicators.
Figure 1-79 Close-up of the BRI and FXS LED Indicators
Memory
The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.
Flash Memory
The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The
onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON
boot code, and a separate non-volatile flash contains the cookie configuration.
Table 1-45 describes the default flash memory storage.
300149
Table 1-45 Flash Memory Storage
Models Flash Memory Storage
Cisco 860 series and 880 series routers 128 MB
Cisco 880 series voice routers and Cisco 890 series routers 256 MB
Cisco 880 series routers with embedded WLAN antennas 256 MB
Cisco 860VAE routers 8 MB boot flash, 128 MB for IOS
Cisco 860VAE-K9 64 MB boot flash and IOS