Cisco ASR 901 10G Series Manual

Cisco Systems, Inc.
www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
Cisco ASR 901 10G Series Aggregation
Services Router Hardware Installation
Guide
November, 2014
Text Part Number: OL-28105-02

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. OR LIMITED WARRANTY, CONTACT YOUR CISCO
REPRESENTATIVE FOR A COPY.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
Copyright © 2012, 2014 Cisco Systems, Inc.

iii
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
CONTENTS
About This Guide vii
Document Revision History vii
Objectives viii
Audience viii
Organization viii
Conventions viii
Safety Warnings ix
Related Documentation ix
Obtaining Documentation, Obtaining Support, and Security Guidelines x
CHAPTER 1Introduction 1-1
Hardware Description 1-1
Cisco ASR 901 10G Router—Front View of TDM Version 1-2
Cisco ASR 901 10G Router—Front View of Ethernet Version 1-3
Cisco ASR 901 10G Router—Rear View 1-4
LEDs 1-5
Power Supply 1-5
Safety Precautions 1-5
Environmental Monitoring Temperature Sensor 1-7
System Specifications 1-7
Router Interface Numbering 1-7
Cisco ASR 901 10G Router 1-8
Regulatory Compliance 1-9
CHAPTER 2Preparing to Install the Router 2-1
Safety Guidelines 2-1
Safety with Equipment 2-1
Safety with Electricity 2-2
Preventing Electrostatic Discharge Damage 2-3
Prerequisites 2-4
Site Planning 2-4
Power Supply Considerations 2-4

Contents
iv
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Site Environment 2-4
Air Flow Guidelines 2-5
Method of Procedure 2-5
Unpacking and Checking the Contents of your Shipment 2-6
Required Tools and Equipment 2-6
Installation Checklist 2-7
Creating a Site Log 2-8
Console Port Considerations 2-8
Console Port Connections 2-8
CHAPTER 3Installing the Cisco ASR 901 10G Router 3-1
Network Modules 3-1
Mounting the Cisco ASR 901 10G Router 3-2
Rack-Mounting Configuration Guidelines 3-2
Attaching Brackets to the Router 3-3
Mounting the Cisco ASR 901 10G Router in a Rack 3-7
Wall-Mounting 3-7
Attaching Brackets for Wall-Mounting 3-8
Mounting the Router on a Wall 3-9
Connecting the Chassis Ground and Power 3-10
Grounding the Cisco ASR 901 10G Router 3-10
Power Connection Compliance 3-12
Wiring the DC-Input Power Source 3-12
Installing the DC Power Cord Retainer 3-13
Installing the AC Power Cord Retainer 3-15
Installing and Removing SFP Modules 3-17
Installing SFP Modules 3-17
Removing SFP Modules 3-19
Connecting Cables 3-20
Connecting the Console Port 3-20
Types of RJ-45 Cables 3-20
Console Port 3-20
Connecting the Network Cables 3-21
Connecting Gigabit Ethernet Interface Cables 3-21
Connecting T1 and E1 Interface Cables 3-21
Connecting SFP Cables 3-22
Connecting Cables to the BITS Interface 3-22
Connecting GPS Cables 3-22
Connecting to Alarm Port 3-23

Contents
v
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Connecting to the Management Ethernet Port 3-23
Dressing Router Cables 3-23
Powering on the Router 3-24
Checklist for Power on 3-24
Interpreting Front-Panel LEDs 3-24
Power-On Procedure 3-24
Formatting Procedures for Flash Memory 3-25
Formatting Flash Memory as a DOS File System 3-25
File and Directory Procedures 3-25
Copying Files 3-25
Displaying Contents of the Flash Memory 3-26
Deleting Files from the Flash Memory 3-26
Displaying File Content 3-27
Enter a Directory and Determine the Current Directory 3-27
What to Do After Installing the Hardware 3-28
APPENDIX ATroubleshooting A-1
Problem Solving A-1
Troubleshooting the Power and Cooling Systems A-2
Environmental Reporting Features A-2
Troubleshooting Cables and Connections A-3
Reading the LEDs A-3
Chassis LEDs A-4
T1/E1 Interface LEDs A-5
SFP Ethernet Interface LEDs A-5
10G SFP+ Ethernet Interface LEDs A-5
RJ-45 Ethernet Interface LEDs A-5
APPENDIX BCable Specifications B-1
Gigabit Ethernet Connector Pinouts B-1
SFP and SFP+ Port Pinouts and Cable Specifications B-2
T1/E1 Port Pinouts B-2
Console Port Signals and Pinouts B-3
Console Port Signals and Pinouts B-4
Identifying a Rollover Cable B-5
BITS Port Pinouts B-6
Time of Day Pinouts B-6
GPS Port Pinouts B-7

Contents
vi
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Alarm Port Pinouts B-8
Management Ethernet Port Pinouts B-8
APPENDIX CSite Log C-1
I NDEX

1
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
About This Guide
This section describes the objectives, audience, organization, and conventions of this hardware
installation guide.
Note Use this document with the documents listed in the “Related Documentation” section on
page 3.
This section contains the following topics:
•Document Revision History, page 1
•Objectives, page 2
•Audience, page 2
•Organization, page 2
•Conventions, page 2
•Safety Warnings, page 3
•Related Documentation, page 3
•Obtaining Documentation, Obtaining Support, and Security Guidelines, page 4
Document Revision History
The Document Revision History table below records technical changes to this guide. The table shows
the document revision number for the change, the date of the change, and a brief summary of the change.
Not all Cisco documents use a Document Revision History table.
Revision Date Change Summary
OL-28105-01 October 2012 Initial version of the document.
OL-28105-02 March 2014 Added information on new variants of the router.

2
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Objectives
This guide explains how to install, maintain, and troubleshoot your router hardware.
It provides the minimum software configuration information. For the detailed configuration procedures,
see the Cisco IOS configuration guide and command reference publications. For more information, see
the “Obtaining Documentation, Obtaining Support, and Security Guidelines” section on page 4.
Warranty, service, and support information is in the Cisco Information Packet that is shipped with your
router.
Audience
This guide is designed for personnel who install, configure, and maintain the router. These persons
should be familiar with electronic circuitry and wiring practices and be experienced electronic or
electromechanical technicians. This guide identifies certain procedures that should be performed only
by trained and qualified personnel.
Organization
Conventions
Note Means reader take note.
Tip Means the following information will help you solve a problem.
Chapter Title Description
Chapter 1 Introduction Describes the hardware features and specifications of
the routers.
Chapter 2 Preparing to Install the Router Describes safety recommendations, site requirements,
network connection considerations, required tools and
equipment, and provides the installation checklist.
Chapter 3 Installing the
CiscoASR90110GRouter
Includes router installation information, and shows
how to connect the router console port.
Appendix A Troubleshooting Describes how to isolate problems, read LEDs,
interpret error and status messages, and recover
software images.
Appendix B Cable Specifications Provides cable specifications to use if you plan to build
your own cables.
Appendix C Site Log Provides example site log.

3
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Caution Means reader be careful. In this situation, you might perform an action that could result in equipment
damage or loss of data.
Safety Warnings
Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might
harm you. A warning symbol precedes each warning statement. The safety warnings provide safety
guidelines that you should follow when working with any equipment that connects to electrical power
or telephone wiring. Warnings are translated into several languages. (For information about compliance
guidelines and translated safety warnings, refer to Cisco Regulatory Compliance and Safety Information
for the Cisco ASR 901 Router.
Related Documentation
For additional information, refer to the following documents:
•Cisco Regulatory Compliance and Safety Information for Cisco ASR 901 Series Aggregation
Services Router
•Cisco ASR 901 Series Aggregation Services Router Software Configuration Guide
•Cisco ASR 901 Series Aggregation Services Router Command Reference
•Release Notes for Cisco ASR 901 Series Aggregation Services Router
To access the related documentation on Cisco.com, go to:
http://www.cisco.com/c/en/us/support/routers/asr-901-10g-series-aggregation-services-routers/tsd-pro
ducts-support-series-home.html
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device.
Statement 1071
SAVE THESE INSTRUCTIONS

4
Cisco ASR 901 10G Series Aggregation Services Router Hardware Installation Guide
OL-28105-02
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly
What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical
documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html