Cisco CVR100W User manual

Quick Start Guide
Cisco Small Business
CVR100W Wireless-N VPN Router
Package Contents
•CVR100W Wireless-N VPN Router
•Power Adapter
•Quick Start Guide
•Ethernet Cable
•Pointer Card with Product Warranty

2 Cisco CVR100W Wireless-N VPN Router Quick Start Guide
Welcome
Thank you for choosing the Cisco CVR100W Wireless-N VPN Router. The
CVR100W provides simple, affordable, secure business-class connectivity
to the Internet for small office/home office (SOHO) and remote
professionals.
This guide describes how to physically install your CVR100W and launch
web-based Configuration Utility to configure and manage your CVR100W.
For additional information, see www.cisco.com/go/cvr100w.
CVR100W Features
Front Panel
Front Panel Buttons
Do-Not-
Disturb
Mode
Button
This button turns on or turns off the lights on the front panel
of the CVR100W. Turning this button on or off will not affect
the normal operation of the CVR100W.
•When this button is turned on, all lights on the front panel
are off and the Do-Not-Disturb Mode light on the back
panel is solid green.
•When this button is turned off, all lights on the front panel
are on and the Do-Not-Disturb Mode light is off.
WPS
Button
This button configures wireless access for devices in your
network that are WPS-enabled. See Front Panel Lights for
more information about the WPS light.
Wireless
Button
This button enables or disables the wireless module. See
Front Panel Lights for more information about the WLAN
light.
1

Cisco CVR100W Wireless-N VPN Router Quick Start Guide 3
Front Panel Lights
LAN
(1-4)
The numbered lights correspond to the LAN ports on the
back panel of the CVR100W.
•Solid blue when the CVR100W is connected to a device
through the corresponding LAN port (1, 2, 3, or 4).
•Flashes blue when the CVR100W is sending or receiving
data over the LAN port.
•Off when the LAN port has no connection.
WPS •Solid blue when the WPS connection is configured.
•Flashes blue when the WPS connection is in progress or
the WPS process is experiencing problems.
•Off when the WPS process finishes or there is no WPS
connection.
WLAN •Solid blue when the wireless module is enabled with
100% Wi-Fi power.
•Solid amber when the wireless module is enabled with
50% Wi-Fi power.
•Flashes blue when the CVR100W is sending or receiving
data on the wireless module.
•Off when the wireless module is disabled.
WAN •Solid blue when the CVR100W is connected to the
Internet through your cable or DSL modem.
•Flashes blue when the CVR100W is sending or receiving
data through the WAN port.
•Off when the WAN port has no connection.
POWER •Solid blue when the CVR100W is powered on and is
operating normally.
•Flashes blue when the system is booting or is upgrading
the firmware.
•Off when the CVR100W is powered off.

4 Cisco CVR100W Wireless-N VPN Router Quick Start Guide
Back Panel
Mounting the CVR100W
You can place your CVR100W on a desktop or mount it on a wall.
Placement Tips
• Ambient Temperature—To prevent the CVR100W from overheating,
do not operate it in an area that exceeds an ambient temperature of
104°F (40°C).
•AirFlow—Be sure that there is adequate air flow around the CVR100W.
• Mechanical Loading—Be sure that the CVR100W is level and stable to
avoid any hazardous conditions.
Place the CVR100W on a flat surface so that it sits on its four rubber feet.
WAN The WAN (Internet) port is connected to your Internet device, such
as a cable or DSL modem.
LAN (1-4) These ports provide a LAN connection to network devices, such as
PCs, print servers, or switches.
RESET The RESET button has two functions:
•Reboot:Press the RESET button for at least 1 but no more than
5 seconds with a pencil tip to reboot the unit.
• Reset to Factory Defaults: Press and hold the RESET button for
more than 5 seconds to reboot the unit and restore the factory
defaults. Changes that you have previously made to the
CVR100W settings are lost.
12VDC This port is where you connect the power adapter (12 V/0.5 A).
POWER Press this button to power the CVR100W on and off.
Do-Not-
Disturb
Mode
Light
•Solid green when the Do-Not-Disturb Mode button on the front
panel is turned on and the CVR100W is operating normally.
•Flashes green when the Do-Not-Disturb Mode button is turned
on but the Internet connection has problems.
•Off when the Do-Not-Disturb Mode button is turned off.
2

Cisco CVR100W Wireless-N VPN Router Quick Start Guide 5
Wall Mounting
The CVR100W can be wall-mounted. The wall-mounting hardware is
user-supplied. The ports on the back panel must face either upward or
downward when mounting the CVR100W to a wall.
WARNING Insecure mounting might damage the device or cause injury.
Cisco is not responsible for damages incurred by insecure
wall-mounting.
Connecting the CVR100W
NOTE The wireless module of the CVR100W is enabled by default. You
can connect one PC with an Ethernet cable or through a wireless
connection to perform the initial configuration. Use the default SSID
name and pre-shared key that are provided on the label at the bottom of
the unit to connect the PC to your wireless network for the first time.
STEP 1Power off all equipment, including the cable or DSL modem, the PC
that you will use to connect to the CVR100W, and the CVR100W.
STEP 2Connect the supplied power adapter to the 12VDC port on the
back panel. Plug the other end of the power adapter into an
electrical outlet. Make sure that the POWER button is turned off.
CAUTION Use only the power adapter that is supplied with the unit.
Using a different power adapter could damage the unit.
STEP 3Connect one end of an Ethernet cable to your cable or DSL
modem. Connect the other end to the WAN port on the back panel.
STEP 4Connect one end of a different Ethernet cable to one of the LAN
ports on the back panel. Connect the other end to an Ethernet port
on the PC that you will use to run web-based Configuration Utility.
NOTE Skip this step if you want to connect the PC to the CVR100W
through a wireless connection.
STEP 5Power on all connected devices including the cable or DSL
modem and the PC and wait until the connections are active.
STEP 6Press the POWER button on the back panel to power on the
CVR100W.
3

6 Cisco CVR100W Wireless-N VPN Router Quick Start Guide
STEP 7To connect the PC to your wireless network for the first time, you
can configure the wireless connection using the default SSID name
and pre-shared key that are provided on the product label.
A sample configuration is illustrated here.
Getting Started with the Configuration
The Setup Wizard and web-based Configuration Utility are supported on
Microsoft Internet Explorer 6.0 or later, Mozilla Firefox 3.0 or later, Apple
Safari 3.0 or later, and Google Chrome 5.0 or later.
To log in to web-based Configuration Utility and complete the initial
configuration by using the Setup Wizard:
STEP 1Connect a PC to an available LAN port on the back panel and power
on the PC. Your PC will become a DHCP client of the CVR100W.
STEP 2Start a web browser. In the address bar, enter the default IP
address of the CVR100W: 192.168.1.1.
NOTE If the default IP address of the CVR100W conflicts with
another device (such as ADSL modem or cable modem) on the
same network, its default IP address will be automatically changed
to 10.10.10.1. You must use the new default IP address to log in to
the utility when IP address conflict occurs.
STEP 3When the login page appears, choose the language that you prefer
to use in the utility and enter the username and password.
The default username is cisco. The default password is cisco.
Usernames and passwords are case sensitive.
STEP 4Click Log In. The Setup Wizard will now launch.
STEP 5Follow the on-screen prompts to complete the initial configuration.
Power
Supply
Internet
Access
Devices
Local
Network
Devices
Wireless
Devices
4

Cisco CVR100W Wireless-N VPN Router Quick Start Guide 7
For security purposes, change the default password as instructed
by the Setup Wizard to prevent unauthorized access.
After the initial configuration is complete, go to the Advanced
Settings pages to configure other advanced features. You are
required to log in to the utility again with the new password. See
the help pages or the Cisco CVR100W Wireless-N VPN Router
Administration Guide for more information on configuring the
advanced features.
Where to Go From Here
Support
Cisco Small Business
Support Community
www.cisco.com/go/smallbizsupport
Cisco Small Business
Support and Resources
www.cisco.com/go/smallbizhelp
Phone Support Contacts www.cisco.com/go/sbsc
Cisco Small Business
Firmware Downloads
www.cisco.com/go/smallbizfirmware
Select a link to download firmware for Cisco
Small Business Products. No login is
required.
Product Documentation
Cisco CVR100W www.cisco.com/go/cvr100w
Cisco Small Business
Cisco Partner Central
for Small Business
(Partner Login Required)
www.cisco.com/web/partners/sell/smb
Cisco Small Business
Home
www.cisco.com/smb
5

78-20934-01
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
www.cisco.com
Small Business Support, Global: www.cisco.com/go/sbsc
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates
in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL:
www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their
respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (1110R)
© 2013 Cisco Systems, Inc. All rights reserved.
Printed in China PRC
78-20934-01
6001-11190062R(YT)