Cisco ASR1002 - ASR 1002 Router User manual

QUICK START GUIDE
Cisco ASR 1002 Router
1Documentation and Resources
2Prepare for Installation
3Rack-Mount the Router
4Connect the Router to the Network
5Start the System
6Configuring the Router
7After Installation

2
1 Documentation and Resources
Documentation for the Cisco 1000 Series Aggregation Services Routers documentation is available online, with the exception
of the regulatory compliance and safety documentation and the Cisco 1000 Series Aggregation Services Routers documentation.
For detailed hardware installation instructions, refer to the Cisco ASR 1000 Series Aggregation Services Routers Hardware
Installation Guide. Refer to the following documentation for information about installation and replacement of parts (including
shared port adapters) and regulatory compliance information:
•Shared port adapter(SPA) documentation—See the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA
Hardware Installation Guide
•Configuration documentation—See the Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
•Regulatory compliance information-See the Regulatory Compliance and Safety Information for the Cisco ASR 1000 Series
Aggregation Services Routers
Document Revision History
The Document Revision History table displays the changes made to this document.
Technical Documentation Ideas Forum
Suggest ways in which Cisco technical documentation can be improved and better serve your needs. Participate in the
Technical Documentation Ideas forum at:
http://www.cisco.com/go/techdocideas
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional information, see the
monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version
3.0.
Document Version Date Change Summary
OL-15411-05 November 2009 Added information about +24 V DC
power supply information pertaining to
the Cisco ASR1002 Router.
OL-15411-04 February 2009 General updates.
OL-15411-03 November 2008 Included information about the
improved two-minute window allotted
time to replace a power supply. You now
have up to a maximum of five minutes to
replace a power supply.
OL-15411-02 September 2008 General updates.
OL-15411-01 July 2008 First version of this document.

3
2 Prepare for Installation
This section contains information about the tools and parts, warnings, site preparation information, and other information for
the rack-mount installation and equipment shelf or tabletop installation.
Warning Only trained and qualified personnel should install, replace, or service this equipment. Statement 1030
Caution The eUSB panel door on the side of the Cisco ASR 1002 Router must not be opened. If there is a problem with
eUSB flash card, the chassis should be returned.
Before beginning the installation of this router, read the Regulatory Compliance and Safety Information for the Cisco ASR 1000
Series Aggregation Services Routers document.
Site Preparation and Unpacking
Ensure that the following guidelines are followed:
•Lift the router safely out of the packing container.
•Ensure that the power service at the site is suitable for the router you are installing.
•Check the packing slip to ensure that all the correct components are present.
•Locate the Site Log and ensure that it is accessible for recording information about the installation.
Tools and Parts
Use the following list of tools and parts as a checklist for preparing to install the Cisco ASR 1002 Router:
•ESD-preventive wrist strap
•AC power cord
•Appropriate cables to connect the router to the network and to the console terminal
•Tape measure and level (optional)
•Number 2 Phillips screwdriver and 3.5 mm or 3/16 inch flat-blade screwdriver
•Two chassis ground lugs and four screws
•The rack-mount and cable-management kit:
– Four 19-inch rack-mount brackets (with front and rear rails) and two cable-management brackets
– Three sets of screws: one set for the front rack-mount brackets (packaged with several black screws), another set for
the rear rack-mount brackets (packaged with several screws), and a set for the cable-management brackets (packaged
with four screws).
Prepare for Equipment Shelf Installation or Tabletop Installation
For an equipment shelf installation or tabletop installation, verify the following before installing the router:
•The router is off the floor and has adequate ventilation.
•An adequate chassis ground (earth) connection exists for the router.
•The router needs at least 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (at the front and rear of the router).
•The router needs 19 inches (48.26 cm) of clearance at the front and rear to allow for installation or to access cables or
equipment.

4
Prepare for Rack-Mount Installation
Before you begin the rack-mounting tasks:
•Decide whether or not you want to rear-mount the chassis from the front or the rear.
•Decide whether or not you want to attach cable-management brackets to your chassis.
Note If you install cable-management brackets, ensure that you use the rack-mount ear holes specified in the procedure
described in and install the brackets after the chassis is mounted on the equipment rack.
•Decide if two-post or four-post rack-mount equipment will be used.
3 Rack-Mount the Router
This section provides information about rack-mounting the router.
Attach the Rack-Mount Brackets—Chassis Front-Mounted
To attach the rack-mount brackets on a Cisco ASR 1002 Router for a front rack-mount configuration, follow these steps:
Step 1 Locate the threaded holes in the front sides of the chassis.
Step 2 Align the rack-mount bracket to the side of the router. Ensure that you hold the rear rack-mount bracket such that the ear holes
are facing outward and towards the rear of the chassis. Depending on which set of rack-mount bracket holes you choose to use
to attach the rack-mount bracket to the router, the chassis will either be recessed into the rack or protrude from the rack.
Step 3 Position the front rack-mount bracket's top hole with the chassis, first top hole behind the side vent holes, as shown in Figure 1.
Figure 1 Front Rack-Mount Brackets in the Cisco ASR 1002 Router
Step 4 Insert and tighten the black screws on one side.
Step 5 Repeat Step 1 through Step 4 on the other side of the chassis. Use black screws to secure the rack-mount brackets to
the chassis.
Step 6 To install the cable-management brackets, see the procedure described in the “Attach a Cable-Management Bracket”
section on page 9.
1Front rack-mount bracket ear and holes 3Front rack-mount bracket screws
2Front rack-mount bracket
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2 QE3 BOOTC
ARRIERL
INKPWRSTATMTSMGMTAUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
3
280278
21

5
Attach the Rack-Mount Brackets—Chassis Rear-Mounted
To install the rack-mount brackets on a Cisco ASR 1002 Router in a rear rack-mount configuration, follow these steps:
Step 1 Locate the threaded ear holes in the rear sides of the chassis.
Step 2 Position the rear rack-mount bracket's top hole with the chassis from the back (See Figure 2). Ensure that you hold the
rear rack-mount bracket with the ear holes facing outward and towards the rear of the chassis. Align the rack-mount
bracket to the side of the router.
Figure 2 Installing the Cisco ASR 1002 Router Rear Rack-Mount Brackets
Step 3 Insert and tighten the screws. After the bracket is secured to the side of the chassis, slide the two remaining components
into the side rack-mount bracket.
Step 4 Repeat Step 1 through Step 3 on the other side of the chassis. Use the screws on each side to secure the rear rack-mount
brackets to the chassis.
This completes the procedure for attaching rear rack-mount brackets to the chassis. Continue to the procedure described in the
Four-Post Rack Installation, page 5 or the Two-Post Rack Installation, page 7.
Four-Post Rack Installation
Note We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the router and the
equipment directly above and below the router.
1Rear rack-mount bracket ear and holes 3Rear rack-mount bracket screws
2Rear rack-mount bracket
280279
2
3
1

6
Figure 3 shows the Cisco ASR 1002 Router in a four-post rack.
Figure 3 Installing the Cisco ASR 1002 Router in a Four-Post Rack - Front and Rear Rack-Mounting
Note Because the rack-mount brackets support the weight of the entire chassis, use all the screws to fasten the two
rack-mount brackets on the chassis to the rack posts.
Note Ensure that you attach the cable-management brackets to the chassis after you install the chassis in an equipment rack.
To install the chassis in the four-post rack, complete the following steps:
Step 1 Make sure that the rack brakes are locked and the rack is stabilized.
Step 2 Mount the chassis by securing the rack-mount brackets to two posts or mounting strips in the rack using the screws
provided.
Step 3 On the chassis, ensure that all the screw fasteners on the installed components are securely tightened.
Step 4 Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are engaged or
that the rack is otherwise stabilized.
Step 5 Lift the chassis into position between the rack posts (requires two people).
Step 6 Align the mounting bracket holes with the rack post holes and attach the chassis to the rack. At this point, if there is a
third person, that person can insert the screws, while the other two people hold the chassis in place, unless the chassis
is resting on a shelf).
Step 7 Position the chassis such that the rack-mounting ears are flush with the mounting rails on the rack.
1Rear rack equipment rail 3Front rack-mount bracket ear and holes
2Rear rack-mount bracket ear and holes 4Front rack equipment rail
280281
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
4
1
3
2

7
Step 8 Insert the bottom screw first and then the second screw at the top of the chassis, diagonally from the bottom screw.
This helps secure the chassis in place while you insert the other screws.
Tip To ensure that there is sufficient space to attach the cable-management brackets to the chassis in the rack easily, use the
rack-mount bracket ear holes specified in Step 9.
Step 9 Hold the chassis in position against the mounting rails and perform these steps:
Tip Insert the bottom screw first and then the second screw at the top of the chassis diagonally from the bottom screw. This
helps secure the chassis in place while you insert the other screws.
a. Insert the bottom screw into the second ear hole from the bottom of the rack-mount ear and use a hand-held screwdriver
to tighten the screw to the rack rail.
b. Insert the top screw into the second bracket hole from the top of the rack-mount bracket ear hole diagonally from the
bottom screw and tighten the screw to the rack rail. See Figure 3.
c. Repeat these Step a and Step b for the other side of the chassis.
Note When the specified rack-mount bracket ear holes are used, the cable-management brackets can be easily attached
to the rack-mount bracket after the chassis is in the rack.
This completes the procedure for installing the chassis in a four-post rack. Proceed to the procedure described in the “Attach a
Cable-Management Bracket” section on page 9 to continue the installation.
Two-Post Rack Installation
Caution If you are using a two-post rack, secure the two-post rack to the floor surface to prevent tipping and avoid bodily
injury and component damage. Or use a four-post rack.
Before you begin to install the Cisco ASR 1002 Router in a two-post equipment rack, read these important notes:
•Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26 cm). Airflow
through the chassis is from front to back.
•To prevent the two-post rack from tipping and avoid bodily injury or component damage, ensure that you secure the
two-post equipment rack to the floor.
•Never attempt to lift an object that might be too heavy for you to lift by yourself. We recommend that at least two people
install the router in an equipment rack.
•Ensure that the floor under the rack supporting the Cisco 1000 Series Routers is capable of supporting the combined weight
of the rack and all the other installed equipment.
Note Ensure that you attach the cable-management brackets to the chassis after you install the chassis in an equipment rack.

8
Figure 4 shows the Cisco ASR 1002 Router in a two-post rack.
Figure 4 Installing a Cisco ASR 1002 Router in a Two-Post Rack
To install the Cisco ASR 1002 Router in a two-post equipment rack, perform the following steps:
Step 1 Position the chassis such that the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any
sudden twists or moves.
Step 2 Slide the chassis into the rack, pushing it back until the rack-mount brackets meet the mounting strips or posts on both
sides of the rack.
Step 3 Position the chassis until the rack-mounting ears are flush against the mounting rails on the rack.
Tip To provide enough space to attach the cable-management brackets to the chassis in the rack easily, ensure that you use
the rack-mount bracket ear holes specified in Step 4.
Step 4 Hold the chassis in position against the mounting rails and perform these steps:
a. The Cisco ASR 1002 Router rack-mount bracket has four ear holes and two for the cable-management brackets. Insert
the bottom screw into the fifth hole from the top of the rack-mount ear, and use a hand-held screwdriver to tighten the
screw to the rack rail.
b. Insert the top screw into the second hole from the top of the rack-mount bracket ear hole diagonally from the bottom
screw, and tighten the screw to the rack rail. See Figure 4.
Step 5 Repeat Steps 3 and Step 4 for the other side of the chassis.
Note If you use the specified rack-mount bracket ear holes, the cable-management brackets can be easily attached to the
rack-mount bracket after the chassis is in the rack.
This completes the procedure for installing the chassis in a two-post rack. Proceed to the procedure described in the “Attach a
Cable-Management Bracket” section on page 9 to continue the installation.
1Rack equipment rail 2Rack-mount bracket ear and holes
280282
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
1
2

9
Attach a Cable-Management Bracket
The cable-management bracket should be mounted to each rack-mount bracket on the chassis to provide cable-management to
both sides of the chassis. These brackets are mounted to the rack-mount brackets using screws to allow easy installation and
removal of cables.
The cable-management bracket for the Cisco ASR 1002 Router contain one independent cable-management U type device with
two screws for each bracket, and provides cable dressing for each card module slot. In the ASR 1000 Series SPA interface, these
brackets work in tandem with the SPA product feature cable-management device to allow the installation and removal of
adjacent cards without the need to remove cables.
Note Ensure that the cable-management bracket U type device is facing upwards when you attach it to the chassis.
Perform these steps to attach the cable-management brackets to both sides of the Cisco ASR 1002 Router in the rack:
Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1002 Router. The
cable-management bracket should be aligned to the top hole of the chassis rack-mount bracket.
Step 2 Using a Phillips screwdriver, insert a screw through the cable-management bracket and into the chassis rack-mount
bracket, and tighten the screw.
Note Use the package of four screws that came with your Cisco ASR 1002 Router.
Step 3 Using the bottom rack-mount ear hole, insert the screw through the cable-management bracket and into the chassis
rack-mount bracket. Figure 5 shows the cable-management brackets attached to the chassis.
Figure 5 Attaching the Cable-Management Brackets to the Cisco ASR 1002 Router
Step 4 Using a Phillips screwdriver and cable-management screw, thread and tighten the screw to the cable-management
bracket.
Step 5 Repeat Step 1 through Step 4 for the other side of the Cisco ASR 1002 Router.
1Secure the cable-management bottom screw and top screw
to this ear hole
3Front rack-mount bracket
2Cable-management U type device
ASR 1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2QE3BOOTCARRIER LINKPWR STAT
MTSMGMTA
UXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
280280
1
1
3
2

10
This completes the procedure for installing the cable-management bracketson a Cisco ASR 1002 Router for a chassis
rack-mount configuration.
Chassis Ground Connection Installation
Connecting the Cisco ASR 1002 chassis to earth ground is required for all DC-powered installations and AC-powered
installations where compliance with Telcordia grounding requirements is necessary.
Caution The dual-lug chassis ground stud must be installed, and all the cards and filler plates must be fully inserted and
screwed in and earthed to prevent a potential hazard in a telecom line.
Have the recommended tools and supplies available before you begin this procedure.
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
Before you connect the power or turn on the power to your router, you must provide an adequate chassis ground (earth)
connection for the Cisco ASR 1002 Router. The chassis ground lugs (two) and the respective screws (four) are provided in the
accessory kit that is shipped with your Cisco ASR 1002 Router.
The following tools, equipment, and supplies are necessary to connect the system ground to the chassis:
•Phillips screwdriver
•Dual-lug chassis ground component (two) and respective screws (four)
•Grounding wire
See Figure 6 for the location of the chassis ground connector on the Cisco ASR 1002 Router.
Figure 6 Cisco ASR 1002 Router Ground Connector Location and eUSB Panel Door
Perform the following steps to install chassis ground connection:
Step 1 Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).
1F0 with Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10
Note The Cisco ASR10002 Router does not support
the Cisco ASR1000-ESP20 module.
3The eUSB panel door on the side of the Cisco ASR 1002
Router must not be opened. If there is a problem with the
eUSB flash card, the chassis should be returned.
2R0 slot with embedded ASR1000-RP1 (Cisco
ASR1000-RP2 is not supported by the Cisco ASR1002
Router) and embedded ASR1000-SIP10
4Cisco ASR 1002 Router ground stud location
ASR1002
stat
pwr
min
maj
crit
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
STAT
QE0QE1QE2QE3BOOTCARRIERLINKPWRSTATMTSMGMTAUXCON
SPA-4XOC3-POS
STATUS
0
1
2
3
C/A
A/L
C/A
A/L
C/A
A/L
C/A
A/L
3
1
2
4
280283