Cisco SGE2000 User manual

LINKSYS ONE COMMUNICATIONS SOLUTION
SGE2000/SGE2000P Gigabit Ethernet
Switch Reference Guide
December 2007

© 2006-2007 Copyright 2006-2007, Cisco Systems, Inc.
Specifications are subject to change without notice.
Linksys, the Cisco Systems logo, the Linksys Logo, and the Linksys One logo are registered trademarks of Cisco Systems,
Inc. All other trademarks mentioned in this document are the property of their respective owners.
Document Revision History
Revision Date Description
1.0 December 2007 Added switch stacking information.

1
Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents
Contents
Chapter 1: Getting Started . . . . . . . . . . . . . . . . . . . 1
Starting the Application 1
Understanding the Interface 4
Device Representation 5
Using the Linksys Management Buttons 6
Using Screen and Table Options 7
Adding Device Information 7
Modifying Device Information 7
Deleting Device Information 8
Resetting the Device 9
Logging Off The Device 9
Chapter 2: Managing Device Information . . . . . . . . . . . . . 11
Understanding the Device Zoom View 11
Defining General System Information 12
SGE 2000P System Information 12
Managing Stacks 13
Building Automatically-Configured Stacks 14
Building a New Stack 14
Adding Units to a Running Stack 14
Building Manually-Configured Stacks 14
Building a New Stack 14
Adding Units to a Running Stack 14
Understanding Stack Resiliency 15
Understanding Advanced Stacking 15
Unit IDs 15
Stack Master 15
Stack Backup Master 15
Stack Members 16
Master-Enabled Units 16
Unit ID Allocation 16
Stack Unit Startup Process 17
Master Discovery Process 17
Master Election Process 17
Unit ID Allocation and Duplicate Unit ID Conflict Resolution 18
Configuring Units and Ports 19
Setting the Unit’s Operational Mode 19
Configuring the Stack Master and Unit ID 19
Resetting the Unit to Factory Default Mode 21
Understanding LED Indicators 21
Stack Troubleshooting and Maintenance 21
Replacing a Failed Member Stack Unit in an Operational Stack 21
Replacing a Failed Stack Master Unit in an Operational Stack 23

2Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents
Splitting a Stack 24
The Stack Master and Backup Master Units Remain in a Group 24
The Stack Master or the Backup Master Unit Remains in a Group 24
Neither the Stack Master Unit or the Backup Master Unit Remains in the Group 25
Merging Two Stacks 26
Understanding Stacking Cable Failure 27
Inserting Too Many Units into a Stack 27
Inserting a Standalone Unit into a Running Stack 28
Viewing Device Health 28
Chapter 3: Managing Power-over-Ethernet Devices . . . . . . . . . 31
DefiningPoE System Information 31
Chapter 4: Configuring Device Security . . . . . . . . . . . . . . 37
Passwords Management 38
Defining User Authentication 38
Defining Authentication 40
Defining Profiles 40
Mapping Profiles 42
Defining TACACS+ 43
Defining RADIUS 47
Defining Access Method 51
Defining Access Profiles 51
Defining Profile Rules 54
Defining Traffic Control 60
Defining Storm Control 60
Defining Port Security 62
Defining 802.1x 66
Defining 802.1X Properties 67
Defining Port Authentication 68
Defining Multiple Hosts 71
Defining Authenticated Host 74
Defining Access Control 75
Defining MAC Based ACL 75
Defining IP Based ACL 77
Defining ACL Binding 84
Defining DOS Prevention 85
Global Settings 85
Defining Martian Addresses 87
Chapter 5: Configuring Device Interfaces . . . . . . . . . . . . . 89
Defining Port Settings 89
Defining LAG Management 94
Defining LAG Settings 96
Configuring LACP 99

3
Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents
Chapter 6: Configuring VLANs . . . . . . . . . . . . . . . . 103
Defining VLAN Properties 104
Defining VLAN Membership 106
Defining Interface Settings 108
Configuring GVRP Settings 111
Protocol Group 114
Protocol Port 116
Chapter 7: Configuring IP Information . . . . . . . . . . . . . 119
Domain Name System 120
Defining DNS Server 120
Host Mapping 122
Configuring Layer 2 124
Configuring IP Addressing: 124
IP Interface 124
ARP 125
Configuring Layer 3 129
Configuring IP Addressing 129
IP Interface 129
ARP Proxy 132
UDP Relay 133
DHCP Relay 136
ARP 137
Defining IP Routing 140
Chapter 8: Defining Address Tables . . . . . . . . . . . . . . 143
Defining Static Addresses 144
Defining Dynamic Addresses 146
Chapter 9: Configuring Multicast Forwarding . . . . . . . . . . 149
IGMP Snooping 149
Defining Multicast Bridging Groups 152
Defining Multicast Forwarding 155
Chapter 10: Configuring Spanning Tree . . . . . . . . . . . . . 157
Defining STP on Interfaces 158
Defining Interface Settings 160
Defining Rapid Spanning Tree 164
Defining Multiple Spanning Tree 168
Defining MSTP Properties 169
Instance to VLAN 170
Instance Settings 170
Interface Settings 171
Chapter 11: Configuring SNMP . . . . . . . . . . . . . . . . 177
SNMP v1 and v2 177

4Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents
SNMP v3 177
Configuring SNMP Security 178
Defining Engine ID 178
Defining SNMP Views 179
Defining SNMP Users 181
Define SNMP Groups 183
Defining SNMP Communities 185
Defining Trap Management 189
Defining Trap Settings 189
Configuring Station Management 190
Defining SNMP Filter Settings 196
Chapter 12: Configuring Quality of Service . . . . . . . . . . . .199
Defining General Settings 200
Defining CoS 201
Defining Queue 202
Mapping CoS to Queue 204
Mapping DSCP to Queue 205
Configuring Bandwidth 205
Defining Advanced Mode 208
Configuring DSCP Mapping 208
Defining Class Mapping 209
Defining Aggregate Policer 211
Configuring Policy Table 214
Defining Policy Binding 217
Defining QoS Basic Mode 219
Chapter 13: Managing System Files . . . . . . . . . . . . . . .221
File Management Overview 221
Firmware Upgrade 222
Save Configuration 223
Copy Files 224
Active Image 225
Chapter 14: Managing System Logs . . . . . . . . . . . . . . .227
Enabling System Logs 227
Viewing the Device Memory Logs 229
Clearing Message Logs 229
Viewing the Flash Logs 230
Clearing Message Logs 230
Viewing Remote Logs 231
Chapter 15: Configuring System Time . . . . . . . . . . . . . .235
Defining System Time 236
Defining SNTP Settings 238
Defining SNTP Authentication 240

5
Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents
Chapter 16: Viewing Statistics . . . . . . . . . . . . . . . . . 243
Viewing Ethernet Statistics 243
Defining Ethernet Interface 243
Resetting Interface Statistics Counters 245
Viewing Etherlike Statistics 245
Resetting Etherlike Statistics Counters 247
Viewing GVRP Statistics 247
Resetting GVRP Statistics Counters 249
Viewing EAP Statistics 249
Managing RMON Statistics 252
Viewing RMON Statistics 253
Resetting RMON Statistics Counters 254
Configuring RMON History 255
Defining RMON History Control 255
Viewing the RMON History Table 258
Configuring RMON Events 259
Defining RMON Events Control 259
Viewing the RMON Events Logs 262
Defining RMON Alarms 263
Chapter 17: Managing Device Diagnostics . . . . . . . . . . . . 269
Viewing Integrated Cable Tests 269
Performing Optical Tests 271
Configuring Port Mirroring 272
Defining CPU Utilization 275
Appendix A: Linksys One Contact Information . . . . . . . . . . 277

6Contents
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Contents

1
Chapter 1: Getting Started
Starting the Application
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Getting Started
This section provides an introduction to the user interface, and includes the following topics:
• Starting the Application
•Understanding the Interface
• Using the Linksys Management Buttons
• Using Screen and Table Options
• Resetting the Device
• Logging Off The Device
Starting the Application
This section contains information for starting the Linksys User Interface.
Note By default, the IP address of the device is assigned dynamically. The IP address can be changed.
It is recommended to configure the IP address statically, if the system is in stack mode, in order to
prevent the user from disconnecting from the network in the event of master switchover.
To open the User Interface:
1. Open a web browser.
2. Enter the device’s IP address in the address bar and press Enter. An Appendix 1, "Enter Network
Password Page" opens:

2Chapter 1: Getting Started
Starting the Application
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Enter Network Password Page
3. Enter a user name and password. The default user name is "admin". The device is not configured
with a default password, and can be configured without entering a password. Passwords are both
case sensitive and alpha-numeric.
4. Click Login The Embedded Web System Home Page opens:
Note If you have logged in automatically via the Service Router user interface, the Tree and Device
views appear and allow you to navigate through the various areas of the web interface. However,
the following page will appear within the frame provided by the Service Router user interface.

3
Chapter 1: Getting Started
Starting the Application
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Embedded Web System Home Page

4Chapter 1: Getting Started
Understanding the Interface
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Understanding the Interface
The following table lists the interface components with their corresponding numbers:
Interface Components
Linksys User Interface Components
Component Description
1 Tree View The Tree View provides easy navigation through the configurable device
features.The main branches expand to provide the subfeatures.
2 Device View The device view provides information about device ports, current
configuration and status, table information, and feature components.The
device view also displays other device information and dialog boxes for
configuring parameters.
3 Table Area The Table area enables navigating through the different device features.
Click the tabs to view all the components under a specific feature.
4 EWS Information The EWS information tabs provide access to the online help, contains
information about the EWS.

5
Chapter 1: Getting Started
Understanding the Interface
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
This section provides the following additional information:
•Device Representation — Provides an explanation of the Linksys user interface buttons, including both
management buttons and task icons.
•Using the Linksys Management Buttons — Provides instructions for adding, modifying, and deleting device
parameters.
Device Representation
The Linksys home page displays a graphical representation of the device:
Device Representation
The Linksys home page contains a graphical SFE2000 and SFE2000P front panel illustration.

6Chapter 1: Getting Started
Using the Linksys Management Buttons
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Using the Linksys Management Buttons
Device Management buttons and icons provide an easy method of configuring device information, and
include the following:
Device Management Buttons
Button Name Button Description
Apply Applies changes to the device.
Clear All Counters Clears statistic counters
Clear Logs Clears log files
Add Opens an Add page
Delete Removes entries from tables
Reset the settings of
Selected Port to
Default
Resets the settlings of a selected port
to the default settings
Test Now Performs cable tests.

7
Chapter 1: Getting Started
Using Screen and Table Options
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Using Screen and Table Options
Linksys contains screens and tables for configuring devices. This section contains the following topics:
•Appendix 1, "Adding Device Information"
• Appendix 1, "Modifying Device Information"
• Appendix 1, "Deleting Device Information"
Adding Device Information
User defined information can be added to specific EWS pages, by opening a new Add page. To add
information to tables or EWS pages:
1. Open an EWS page.
2. Click the Add button. An add page opens, for example, the Add SNTP Server Page:
Add SNTP Server
3. Define the fields.
4. Click Apply. The configuration information is saved, and the device is updated.
Modifying Device Information
1. Open the EWS page.
2. Select a table entry.
3. Click the Edit Button. A Modify page opens, for example, the Interface priority Page opens:

8Chapter 1: Getting Started
Using Screen and Table Options
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Edit Interface Priority
4. Define the fields.
5. Click Apply. The fields are modified, and the information is saved to the device.
Deleting Device Information
1. Open the EWS page.
2. Select a table row.
3. Check the Remove checkbox.
4. Click the Delete button. The information is deleted, and the device is updated.

9
Chapter 1: Getting Started
Resetting the Device
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1
Resetting the Device
The Reset page enables the device to be reset from a remote location. Save all changes to the Running
Configuration file before resetting the device. This prevents the current device configuration from being
lost. To reset the device:
1. Click System > General > Reset. The Reset page opens.
Reset Page
2. Click the Reset button. Each unit can be reset individually. Resetting the stack master results in
resetting the entire stack. If the master unit is reset, the device is reset, and a prompt for a user name
and password is displayed.
3. Enter a user name and password to reconnect to the Web Interface, if the stack is not part of a full
Linksys One system. If the stack is part of a Linksys One system, login is automatically done from
the Service Router.
Logging Off The Device
1. Click . The system logs off. The Embedded Web System Home Page closes.

10 Chapter 1: Getting Started
Logging Off The Device
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
1

11
Chapter 2: Managing Device Information
Understanding the Device Zoom View
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
2
Managing Device Information
This section provides information for defining both basic and advanced system information. This section
contains the following topics:
• Understanding the Device Zoom View
• Defining General System Information
• Managing Stacks
Understanding the Device Zoom View
The Zoom Page is the main window used for viewing the devices either in stand-alone mode or operating
in a stack. To open the Zoom Page:
1. Click the System > System Management > Zoom. The Zoom Page opens:
Zoom Page
The Zoom Page contains the following port indicators:
•Green — Indicates the port is currently operating.
•Red — indicates the port is not currently operating.

12 Chapter 2: Managing Device Information
Defining General System Information
SGE2000/SGE2000P Gigabit Ethernet Switch Reference Guide
Chapter
2
Defining General System Information
SGE 2000P System Information
The System Information page contains parameters for configuring general device information.
SGE 2000 System Information Page
The System Information contains contains the following fields:
•Model Name — Displays the user defined user name.
•System Name — Displays the user configured name of the system. Configured in the Network page.
•System Location — Defines the location where the system is currently running. The field range is
up-to 0-160 Characters.
•System Contact — Defines the name of the contact person.The field range is up to 0-160
Characters.
•System Object ID— Displays the vendor’s authoritative identification of the network management
subsystem contained in the entity.
•System Up Time — Displays the amount of time that has elapsed since the last device reset. The
system time is displayed in the following format: Days, Hours, Minutes and Seconds. For example:
41 days, 2 hours, 22 minutes and 15 seconds.
•Base MAC Address — Displays the device MAC address. If the system is in stack mode, the Base
MAC Address of the master unit is displayed.
•Hardware Version — Displays the hardware version number. If the system is in stack mode, the
hardware version of the master unit is displayed.