Cisco SRP520 User manual

Quick Start Guide
Cisco SRP500 Series Services Ready Platforms
(SRP520 Models)
Package Contents
•Cisco SRP500 Series Services Ready Platform
•RJ-45 Ethernet Cable
•RJ-11 Telephone Cable
•Power Clip and Adapter
•Quick Start Guide
•Product CD

2 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models)
Welcome
Thank you for choosing Cisco SRP500 Series Services Ready Platforms.
This guide describes how to physically install the SRP and how to use the
Setup Wizard to configure it.
Before You Begin
Before you begin the installation, make sure that you have the following:
For Hardware Installation
•An active Internet connection.
•(Optional) Analog phone line.
•(Optional) Telephone handset, fax machine, or PBX line for connecting
to the voice ports.
•Cables
– RJ-45 Ethernet cables (Category 5 or higher) for connecting
computers, WAN and LAN interfaces, phones, or other devices.
– RJ-11 telephone cable for analog line (FXO) and phone (FXS)
connections.
– ADSL splitter, if required by your Service Provider.
•(Optional) Mobile Broadband USB Modem.
For Software Installation:
•A computer running:
– Microsoft Internet Explorer 7.0 (or later), or Mozilla Firefox 3.6.
– Adobe Flash Player with add-on version 10.0.0 or later (needed to
to configure your SRP).
1

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models) 3
Default Settings
Use these default settings when configuring your SRP with the Setup
Wizard. See Getting Started with the Configuration, page 11.
To configure advanced features (such as wireless, network, and voice
settings), log in by using the Administrator account.
For more information, see the Cisco SRP500 Series Services Ready
Platforms Administration Guide (SRP520 Models) at:
www.cisco.com/go/srp500.
NOTE If you obtained your SRP from your Service Provider, you might not
have access to the Administrator account. Contact your Service
Provider for more information.
Getting to Know the Cisco SRP500 Series
Services Ready Platforms
This section lists the available model numbers to help you become familiar
with your SRP, and shows the front panel, back panel, side view, and top
the unit.
NOTE To get started with the installation right away, see Installing the
SRP500 Services Ready Platforms, page 8.
Parameter Value
Device IP 192.168.15.1
Username cisco
Password cisco
DHCP Range 192.168.15.100 to 149
2

4 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models)
Model Numbers
Front Panel
SRP521W Front Panel
SRP526W and SRP527W Front Panel
Model Description
SRP521W Fast Ethernet WAN
2 Phone (FXS) ports, 1 Line (FXO) port, 1 WAN (10/100) port,
4 LAN (10/100) ports, 1 USB 2.0 port, 802.11n, and WiFi Protected
Setup (WPS)
SRP526W ADSL2+ Annex B (ADSL over ISDN)
2 Phone (FXS) ports, 1 Line (FXO) port, 1 DSL port,
4 LAN (10/100) ports, 1 USB 2.0 port, 802.11n, and WiFi Protected
Setup (WPS)
SRP527W ADSL2+ Annex A/M (ADSL over POTS)
2 Phone (FXS) ports, 1 Line (FXO) port, 1 DSL port,
4 LAN (10/100) ports, 1 USB 2.0 port, 802.11n, and WiFi Protected
Setup (WPS)
276377
LANPOWER/SYS PHONE USB WPSWLANWLAN
Cisco Small Business Pro
SRP 521W
12 2143
195210
LANPOWER/SYS PHONE CD Data
DSL
USB WPSWLAN
Cisco Small Business Pro
SRP 526W
12 2143

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models) 5
Front Panel Lights
The following table describes the lights on the front panel of the SRP.
These lights are used for monitoring system activity.
Back Panel
The back panel is where you connect the network devices. The ports on
the panel vary depending on the model.
Lights (Green) Description
POWER/SYS Lights when the SRP has successfully booted and is ready
to use. Flashes when the SRP is booting.
LAN ports (1–4) Lights when a link is established. Flashes when there is
activity on the LAN port.
WAN por t
(SRP 521W only)
Lights when a link established. Flashes when there is
activity on the WAN port.
Phone (FXS) ports
(1–2)
Lights when the port is connected to a phone or fax
machine and the SRP is able to make and receive calls.
Flashes when a call is in progress on the port.
DSL CD Flashes when a DSL service is detected. Lights solid green
when synchronized.
DSL Data
(SRP 526W/527W only)
Flashes when there is DSL activity on the line.
WLAN Lights when the radio is powered on and operational.
Flashes when there is wireless activity on the WLAN port.
USB port Lights when the connected USB device is operational.
Flashes if there is a device failure or unsupported device.
WPS button Lights when WiFi Protected Setup (WPS) is operational.
A slow green flash indicates that the setup is in progress. A
fast green flash indicates a setup error.

6 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models)
SRP521W Back Panel
SRP526W and SRP527W Back Panel
Back Panel Descriptions
Feature Description
DSL port
SRP526/SRP527W only
Connects the SRP to your DSL connection.
Phone (FXS) ports (1–2) Connect directly to an analog telephone, fax machine,
or similar device.
If your analog phone requires a separate bell line (as
might be the case in the United Kingdom), you might
need to connect a ring adapter between the SRP and
your phone so that the phone rings when calls are
presented.
Line (FXO) port Connects to a PSTN, which is the analog telephone
service network that a traditional telephone service
uses.
276375
12VDC
LAN (10/100)WAN (10/100)
21 1234
LINE (FXO)PHONE (FXS)
WAN
Port
On/Off
Switch
12 V DC
power
Line
(FXO)
Port
Phone
(FXS)
Ports
LAN
Ports
195211
LAN (10/100)LAN/WAN
21 1234
LINE (FXO)DSL PHONE (FXS)
On/Off
Switch
Line
(FXO)
Port
DSL
Port
Phone
(FXS)
Ports
LAN
Ports
12 V DC
power

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models) 7
Side View
WAN (10/100) port
SRP521W only
Connects the SRP to your Wide-Area-Network (WAN).
LAN (10/100) ports (1–4) Connects to a wired computer and other network
devices.
On/Off Switch Powers the SRP on or off.
12 V DC power Connects to the provided power adapter.
Feature Description
Reset button Press and hold for 5 seconds to reset the SRP. Press
and hold for 10 seconds to reset the SRP to its factory
defaults.
To press the button, insert a paper clip or similar
object into the opening.
CAUTION Resetting the unit will delete all user
settings.
USB port Connects to a compatible USB Modem.
See Installing a Mobile Broadband USB Modem
(Optional), page 12.
Antenna The WiFi antenna.
276380
RESET
Reset
Button
USB
Connector
276381
Antenna

8 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models)
Top View
Installing the SRP500 Services Ready
Platforms
You can install the SRP on a desktop or other flat horizontal surface or
mount it on a wall.
NOTE The SRP has an adjustable WiFi antenna located on the side panel
of the unit.
Placement Tips
Make sure that you install the SRP in a location that meets these
environmental conditions:
•StorageTemperature(sea level) -22° F to 140° F (-30° C to +60° C)
•OperatingTemperature(sea level) 32° F to 104° F (0° C to 40° C)
• Relative Humidity (sea level) 5 to 95% RH (non-condensing)
Feature Description
WPS Button Use to automatically configure wireless security for devices
that support WiFi Protected Setup (WPS).
To configure WPS, press and hold this button until the WPS
light flashes. Make sure that the device is located near the
SRP during setup.
276378
WPS Button
3

Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models) 9
CAUTION Do not stack or place anything on top of the SRP, or install it on
a hot surface.
Desk Placement
To mount the SRP on a desktop, place the device horizontally on a flat
surface so it sits on its four rubber feet.
Wall Mounting
NOTE Position the SRP so that the back panel faces upward to reduce
strain on the cable connections.
STEP 1Secure two number-six pan-head tapping screws, 3/4-inch (19 mm)
in length, 150 mm apart into a wall for horizontal orientation or
108 mm for vertical orientation, with the space between the
underside of each screw head and the surface of the wall equal to
5/32 inch (4mm).
CAUTION For drywall installation, secure the screws by using two
hollow-wall anchors (1/8 inch with 5/16-inch drill bit, or M3
with 8-mm drill bit). Without proper anchoring, the strain of
the network cable connections could pull the SRP from
the wall.
STEP 2Locate the mounting screw slots on the bottom of the SRP, and
then hang it on the screws.
Connecting the Equipment
STEP 1For Ethernet WAN connections, connect one end of the Ethernet
cable to your Internet access device (typically a modem), and
connect the other end of the cable to the WAN port.
For ADSL connections, connect your DSL cable directly to the DSL
port on your SRP526W or SRP527W. Make sure that you use an
ADSL splitter, if required by your Service Provider.
4

10 Cisco SRP500 Services Ready Platforms Quick Start Guide (SRP520 Models)
SRP521W WAN Connection
SRP526W / SRP527W ADSL Connection
STEP 2Connect wired computers and other network devices to the LAN
ports (1–4).
STEP 3(Optional) Connect an analog telephone, fax machine, or similar
device to the Phone (FXS) ports. Then connect the Line (FXO) port
to the telephone line on your phone jack.
STEP 4Install the supplied AC power plug or clip (for your area) into the
power adapter.
NOTE Only use the power adapter that was provided with the unit.
STEP 5Connect the power adapter to the 12 VDC port on your SRP.
195790
12VDC
LAN (10/100)WAN (10/100)
21 1234
LINE (FXO)PHONE (FXS)
WAN (10/100) Port
199989
LAN (10/100)LAN/WAN
21 1234
LINE (FXO)DSL PHONE (FXS)
DSL Port
195791
12VDC
LAN (10/100)WAN (10/100)
21 1234
LINE (FXO)PHONE (FXS)