Cisco TelePresence MX700 User manual

78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved. http://www.cisco.com/go/mx-docs
Installation guide
for Cisco TelePresence MX700 Single Camera
mounted on the wall

78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 2
This guide covers the MX700 with single camera, mounted on the wall.
Safety information
Due to the size and mass of this product it is important
that the wall-mounted system is safely installed
according to these installation instructions.
The wall and mounting hardware must be able to safely
support the product.
The wall-mounted system must be installed by qualified
personnel, in accordance with state and local building
regulations.
Manpower
We recommend three
people working together
to mount this system.
Follow local regulations.
Dimensions
Height: 1071mm / 42.2in.
Width: 2517 mm / 99.1in.
Depth: 148 mm / 5.9in.
Weight: 161 kg / 355lb
Room setup
Explore the Cisco Project Workplace website to
find inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
Documentation
Cisco Spark: Visit the Cisco Spark help site to find
more information about Spark registered room
systems, http://help.ciscospark.com
Other services: Visit the Cisco web site
to find user guides and compliance and
safety information for the video system,
http://www.cisco.com/go/mx-docs

78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 3
Packaging
1Open the plastic snap locks and remove the
side walls.
Lift off box L/M. Lay box A flat on the floor
and remove the lid.
2
L/M
A
D
Boxes are labeled A to M. This
guide refers to the labels.
A M
...
B+E-G Shows which boxes are inside.
Tools and screws are in this box.

78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 4
Tools
Allen key, 4 mm
Allen key, 2.5mm
Torx T20
Screws
The screw kit may contain more screws than you need,
because the same kit is shipped with all mounting options.
M6x90, countersunk
Tool: Allen key, 4mm
M6x35, countersunk
Tool: Allen key, 4mm
M6x12, countersunk
Tool: Allen key, 4mm
M6x12, pan
Tool: Allen key, 4mm
M4x8, pan
Tool: Allen key, 2.5 mm
PT4x10, pan
Tool: Tor x T20
M6x100, pan
Tool: Allen key, 4mm 声
明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.

1 Assemble lower frame
A, B
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 5
Six screws from the back
and two from the top.
8 × M6x12, countersunk

2 Fasten center bracket
B
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 6
2 × M6x12, pan

3 Mount left wall bracket
C
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 7
Check that the wall bracket is level and mark the required
screw hole positions on the wall. Use at least four screws
when fastening the wall bracket. The wall bracket can be
fastened through any of the horizontal slots.
Fasten the wall bracket in a secure manner ensuring that
the wall’s structure is sufficient to support the system load
(screws and mounting hardware not provided; not shown in
illustration).
The lower edge of the screen
image will be at the height of
these horizontal slots.
We recommend that the
distance from the floor to this
line is 70 cm / 27.6in.*
*If you mount the system higher, note the following consequences:
- You may need to increase the distance between the video system and the table in
order for the camera to capture the closest participants.
- The camera gives an elevated view of the room. This view is not optimal for video
conferencing.
Further information: http://www.cisco.com/go/projectworkplace
2D CAD drawings with measurements: http://www.cisco.com/go/mx-docs (Technical
References)

4 Mount right wall bracket
A
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 8
You may use the lower frame to check that the
two brackets are level.
Follow the same instructions for mounting the left
wall bracket. Refer to step 3.
254 mm
(10 in.)

5 Mount spacers and top wall brackets
A
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 9
Snap the top wall brackets onto
the spacers. Face the narrow slots
against the wall.
Fasten the top wall brackets in a secure
manner ensuring that the wall’s structure
is sufficient to support the system
(screws and mounting hardware not
provided; not shown in illustration).
2
1Mount spacers onto the
wall brackets.
Fasten each spacer with
two screws (not provided;
not shown in illustration).

6 Fasten lower frame
78-100254-03A0 | 2016 JUNE | © 2016 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Single camera - Wall mount
Page 10
4 × M6x12, pan