Cisco Catalyst IE3400 Heavy Duty Series User manual

Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
First Published: 2019-09-03
Last Modified: 2019-09-05
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: [phone]
800 553-NETS (6387)
Fax: [phone]

©2019 Cisco Systems, Inc. All rights reserved.

CONTENTS
Preface vii
Audience vii
Purpose vii
Conventions vii
Related Publications viii
Product Overview 1
CHAPTER 1
Product Overview 1
Switch Models and Power Supply 1
Front Panel of the Switch 3
10/100BASE-T Ports 3
Power Connector 4
Alarm Connector 4
Console Management Port 5
LEDs 6
System LED 6
Express Setup LED 6
Power Status LEDs 7
Alarm LEDs 7
Port Status LEDs 7
IP67 Power Supply 8
Switch Installation 9
CHAPTER 2
Switch Installation 9
Preparing for Installation 9
Warnings 9
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
iii

Installation Guidelines 11
Verifying Package Contents 12
Tools and Equipment 12
Installing or Removing the Memory Card (Optional) 13
Connecting a PC or Terminal to the Console Port 14
Connecting to Power 14
Grounding the Switch 15
Running Express Setup 17
Launching WebUI 19
Connecting Alarm Circuits 19
Wiring the External Alarms 20
Connecting Destination Ports 20
Connecting to 10/100 and 10/100/1000 Ports 20
Where to Go Next 21
Switch Mounting 23
CHAPTER 3
Switch Mounting 23
Mounting the Switch 23
Installing the Switch on the Wall 23
Troubleshooting 27
CHAPTER 4
Troubleshooting 27
Diagnosing Problems 27
Switch Connections 27
Switch Performance 28
Resetting the Switch 29
How to Recover Passwords 30
Troubleshooting Express Setup 30
Finding the Switch Serial Number 30
Technical Specifications 31
CHAPTER 5
Technical Specifications 31
Operating Temperature Specifications 31
Technical Specifications 31
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
iv
Contents

Connectors and Cabling 33
Torque Specifications 33
Alarm Ratings 34
Configuring the Switch 35
CHAPTER 6
Configuring the Switch 35
Entering the Initial Configuration Information 35
IP Settings 35
Completing the Setup Program 35
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
v
Contents

Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
vi
Contents

Preface
Audience
This guide is for the networking or computer technician responsible for installing Cisco Catalyst IE3400
Heavy Duty Series switches. We assume that you are familiar with the concepts and terminology of local area
networking (LAN).
Purpose
This guide describes the physical and performance characteristics of each switch, explains how to install a
switch, and provides troubleshooting information.
Additional product information is available at http://www.cisco.com/en/US/products/ps12451/index.html
For additional documentation, see the Cisco Catalyst IE3400 Heavy Duty Series documentation at
http://www.cisco.com/en/US/products/ps12451/tsd_products_support_series_home.html
For information about the Cisco IOS commands, see
http://www.cisco.com/cisco/web/psa/configure.html?mode=prod&level0=268438303
Conventions
This document uses the following conventions and symbols for notes, cautions, and warnings.
Means reader take note. Notes contain helpful suggestions or references to materials not contained in this
manual.
Note
Means reader be careful. In this situation, you might do something that could result in equipment damage or
loss of data.
Caution
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device. Statement 1071
Danger
The safety warnings for this product are translated into several languages in the Regulatory Compliance and
Safety Information for the Regulatory Compliance and Safety Information for the Cisco Catalyst IE3400
Heavy Duty Series Switches that ships with the product. The EMC regulatory statements are also included
in that guide.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
vii

Related Publications
Before installing, configuring, or upgrading the switch, see the product release notes on Cisco.com for the
latest information.
See www.cisco.com/en/US/products/ps12451/tsd_products_support_series_home.html.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
viii
Preface
Related Publications

CHAPTER 1
Product Overview
•Product Overview, on page 1
Product Overview
The Cisco®Catalyst®IE3400 Heavy Duty Series is Cisco’s next-generation, IP66 and IP67-rated switching
platform designed to provide enhanced network-based security, segmentation, and visibility in the most
demanding industrial environments. The Cisco®Catalyst®IE3400 Heavy Duty Series switches extend the
power of intent-based networking to the harshest Internet of Things (IoT) edge.
The Cisco Catalyst IE3400 Heavy Duty Series switches deliver the advanced capabilities similar to the Cisco
Catalyst IE3400 Rugged Series in environments that have heavy exposure to dust and water. These switches
are available with 8, 16, or 24 Fast Ethernet (D-coded) or Gigabit Ethernet (X-coded) M12 interfaces. The
switches can be wall mounted and deployed without a housing cabinet.
Installation details are provided in the Switch Installation section.
Note
The IE3400 Heavy Duty Series switches are powered by Cisco IOS®XE, a next-generation operating system
with built-in security and trust, featuring Secure Boot, image signing, and the Cisco Trust Anchor module.
Cisco IOS XE also provides API-driven configuration with open APIs and data models.
The IE3400 Heavy Duty Series can be managed with powerful tools such as Cisco DNA Center and Industrial
Network Director, and can be easily set up with a completely redesigned, user-friendly, modern GUI tool
called WebUI. The platform also supports Flexible NetFlow for real-time visibility into traffic patterns and
threat analysis with Cisco Stealthwatch®.
Most of the documentation related to this product can be found at
http://www.cisco.com/en/US/products/ps12451/tsd_products_support_series_home.html
Switch Models and Power Supply
Figure 1: Cisco Catalyst IE3400 Heavy Duty Series
The following table lists and describes the switches and power supply. All IP66 and IP67 switches use the
LAN Base Cisco iOS firmware.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
1

Table 1: Switch and Power Supply Descriptions
IE-3400H-24TIE-3400H-24FTIE-3400H-16TIE-3400H-16FTIE-3400H-8TIE-3400H-8FTHardware Specifications
N/A24N/A16N/A8Total 100-Mbps
D-coded ports
24N/A16N/A8N/ATotal 1-Gbps X-coded
ports
SD card
See Note 1.
SD card
See Note 1.
SD card
See Note 1.
SD card
See Note 1.
SD card
See Note 1.
SD card
See Note 1.
Removable storage
1 alarm
output relay
1 alarm
output relay
1 alarm
output relay
1 alarm
output relay
1 alarm
output relay
1 alarm
output relay
Alarm outputs
See Note 2 and 3.
1 alarm
input
1 alarm
input
1 alarm
input
1 alarm
input
1 alarm
input
1 alarm
input
Alarm inputs
See Note 2.
111111Console ports
See Note 2.
Mini-change,
(single
power
source)
Mini-change,
(single
power
source)
Mini-change,
(single
power
source)
Mini-change,
(single
power
source)
Mini-change,
(single
power
source)
Mini-change,
(single
power
source)
Power input
Note 1. The SD card is optional and is not shipped by default with the switch.
Note 2. Using an M12 A-coded 5-pin connector.
Note 3. Relay max. rating: 24VDC at 1A, 48VDC at 0.5A.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
2
Product Overview
Switch Models and Power Supply

Front Panel of the Switch
This section describes the front panel components. The following figures depict the components available on
the various models in this product family. Not all models are illustrated.
Figure 2: Catalyst IE3400H Front Panel
Console Port (left)
Alarm Port (right)
6Switch Status
LEDs
1
Ground Lug7Ethernet ports2, 3,
4
SD Card Cover8Power Input Port5
10/100BASE-T Ports
You can set the 10/100BASE-T ports to operate at 10 or 100 Mb/s over IP standard M12 cabling. The ports
can operate in full-duplex, half-duplex, autonegotiate (default), or never half-duplex mode.
ANever Half Duplex option for a port functions as the name implies, the link is never established at half
duplex; it is either full-duplex or no link. Never Half Duplex avoids the unpredictable response times that in
a CSMA/CD network can cause safety features to trip or interruptions that require restarting the process flow.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
3
Product Overview
Front Panel of the Switch

Figure 3: FE Ports
RD
–
3RD
+
1
TD
–
4TD
+
2
Power Connector
You connect the DC power to the switch through the front panel connector. The power connector labeling is
on the panel. Torque power connection to 10in/lbs.
Figure 4: Power Connector
DC–3NC1
NC4DC+2
Alarm Connector
You connect the alarm signals to the switch through the alarm connector. The switch supports one alarm
output relay.
The alarm output circuit is a relay with a normally open and a normally closed contact. The switch is configured
to detect faults that are used to energize the relay coil and change the state on both of the relay contacts:
normally open contacts close, and normally closed contacts open. The alarm output relay can be used to control
an external alarm device, such as a bell or a light. The alarm output is rated at 24Vdc/1A, 48Vdc/0.5A
maximum.
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
4
Product Overview
Power Connector

Figure 5: Alarm Connector
Alarm In Reference4NO Alarm Output Normally Open (NO) connection1
COMMON Alarm Common connection5NC Alarm Output Normally Closed (NC) connection2
Alarm In3
Console Management Port
You can connect the switch to a PC running Microsoft Windows or to a terminal server through the 5-pole
A-coded console port and configure it by using the CLI. The baud rate and format of the console port is:
• 9600 baud
• 8 data bits
• 1 stop bit
• No parity
• None (flow control)
Figure 6: Console Connector
RXD4RTS1
GND5CTS2
TXD3
For specified cable, use Cisco Product CAB-CONSOLE-M12=
Note
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
5
Product Overview
Console Management Port

LEDs
You can use the LEDs to monitor overall system status and power supply input and output status as well as
port and alarm status.
Figure 7: Switch LEDs
System LED
The System LED shows whether the device is receiving power and is functioning properly.
Table 2: System LED
StatusColor
Switch is not powered on.Off
Boot fast (power-on self test) is in progress.Blinking
green
Switch is operating normally.Green
Switch is not functioning properly.Red
Express Setup LED
The Express Setup LED displays the status of the initial setup for the initial configuration.
Table 3: Setup LED
StatusColor
Configured as a managed switch.Off (dark)
Operating normally running the initial setup configuration.Solid green
Performing the initial setup, in recovery, or the initial setup is incomplete.Blinking
green
Failed to start initial setup or recovery because there is no available port to link the switch
to the management station. Disconnect a device from a switch port, and then press the Express
Setup button.
Solid red
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
6
Product Overview
LEDs

Power Status LEDs
If power is present on the circuit, the LED is green. If power is not present, the LED color depends on the
alarm configuration. If alarms are configured, the LED is red when power is not present; otherwise, the LED
is off.
Table 4: Power Status LEDs
System StatusColor
Power is present on the associated circuit, system is operating normally.Green
Power is not present on the circuit or the system is not powered up.Off
An alarm has been configured to indicate that power is not present on the associated circuit or the
power input dropped below the lowest valid level.
Red
For information about the power LED colors and behaviors during the boot fast sequence, see the “LEDs”
section.
Alarm LEDs
The following table list the alarm LED colors and their meanings.
Table 5: Alarm Out Status LEDs
System StatusColor
Alarm out is not configured or the Switch is off.Off
Alarm out is configured, no alarms detected.Green
Major alarm detected.Blinking
red
Minor alarm detected.Red
Port Status LEDs
Each 10/100BASE-T or 10/100/1000Base-T port (identified by numbers 1-23, depnding upon the the model)
has a port status led.
Table 6: Port Status LEDs
StatusColor
No link.Off
Link present. No activity.Solid green
Port is actively sending or receiving data.Blinking green
Link fault. Errors that affect connectivity and throughput, such as excessive
collisions, CRC errors, and alignment and jabber errors, are monitored.
Alternating green-amber
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
7
Product Overview
Power Status LEDs

Port is not forwarding. The port was disabled by management, an address violation,
or STP.
After a port is reconfigured, the port LED can remain amber for up to
30 seconds while STP checks the switch for loops.
Note
Solid amber
IP67 Power Supply
The switch is offered with optional IP67 power supplies, (PWR-IE160W-67-DC=) and
(PWR-IE180W-67-AC=). The IP67 DC power supply can take 18 to 60Vdc input and provide a 54V, 160W
DC output. The IP67 AC power supply can take 85-264VAC/ input and provide a 54V, 180W DC output.
There are also non-IP67 power supplies compatible with the switch.
The power supplies are sold separately.
Note
The following figure displays the IP67 Power Supply.
Figure 8: Cisco IP67 Power Supply
DC input power connector3DC output connector1
Status LED2
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
8
Product Overview
IP67 Power Supply

CHAPTER 2
Switch Installation
•Switch Installation, on page 9
Switch Installation
This chapter describes how to install your switch, verify the boot fast, and connect the switch to other devices.
It also includes information specifically for installations in hazardous environments.
We recommend performing a preliminary configuration of the switch before it is installed in a permanent
location.
Preparing for Installation
Warnings
These warnings are translated into several languages in the Regulatory Compliance and Safety Information
for this switch.
Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces,
and watches). Metal objects will heat up when connected to power and ground and can cause serious burns
or weld the metal object to the terminals. Statement 43
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement
1001
Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
Warning
Read the installation instructions before you connect the system to its power source. Statement 1004
Warning
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
9

This unit is intended for installation in restricted access areas. A restricted access area can be accessed only
through the use of a special tool, lock and key, or other means of security. Statement 1017
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence
of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician
if you are uncertain that suitable grounding is available. Statement 1024
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030
Warning
Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements
in IEC 60950 based safety standards. Statement 1033
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations. Statement
1040
Warning
For connections outside the building where the equipment is installed, the following ports must be connected
through an approved network termination unit with integral circuit protection.10/100/1000 Ethernet, Console,
and Alarm Statement 1044
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended
ambient temperature of: 140°F (60°C) Statement 1047
Warning
Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning
Airflow around the switch must be unrestricted. To prevent the switch from overheating, there must be the
following minimum clearances:– Top and bottom: 2.0 in. (50.8 mm)– Sides: 2.0 in. (50.8 mm)– Front: 2.0
in. (50.8 mm)
Caution
If installer is providing cabling for an IP66/IP67 and Type 4X rated environment, the cables must be suitably
rated for IP66/IP67 and Type 4X requirements
Caution
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
10
Switch Installation
Warnings

EMC Environmental Conditions for Products Installed in the European Union
This section applies to products to be installed in the European Union.
The equipment is intended to operate under the following environmental conditions with respect to EMC:
• A separate defined location under the user’s control.
• Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.
• AC-power distribution shall be one of the following types, where applicable: TN-S and TN-C as defined
in IEC 364-3.
In addition, if equipment is operated in a domestic environment, interference could occur.
Installation Guidelines
When determining where to place the switch, observe these guidelines.
Environment and Enclosure Guidelines
Review these environmental and enclosure guidelines before installation:
•This equipment is considered Group 1, Class A industrial equipment, according to IEC/CISPR Publication
11. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic
compatibility in other environments due to conducted as well as radiated disturbance.
To meet IP67 Compliance, all cables, dust caps, or the captive screws on the SD card cover must be torqued
to the recommended spec before operating the unit. For torque specs see “Cisco IE 2000 IP67 Series Switches
Technical Specifications”
Caution
Use caution when removing dust caps. Dust caps in an over-tightened state may adhere to the connector O-ring
seal. Ensure that the O-ring remains in place when dust caps are removed and follow all torque specs here:
“Cisco IE 2000 IP67 Series Switches Technical Specifications”
Caution
General Guidelines
Before installation, observe these general guidelines:
Proper ESD protection is required whenever you handle Cisco equipment. Installation and maintenance
personnel should be properly grounded by using ground straps to eliminate the risk of ESD damage to the
switch.Do not touch connectors or pins on component boards. Do not touch circuit components inside the
switch. When not in use, store the equipment in appropriate static-safe packaging.
Caution
• If you are responsible for the application of safety-related programmable electronic systems (PES), you
need to be aware of the safety requirements in the application of the system and be trained in using the
system.
When determining where to place the switch, observe these guidelines:
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
11
Switch Installation
EMC Environmental Conditions for Products Installed in the European Union

• Before installing the switch, first verify that the switch is operational by powering it on and observing
boot fast. Follow the procedures in the “Where to Go Next” section on page 14 .
• For 10/100 ports and 10/100/1000 ports, the cable length from a switch to an attached device cannot
exceed 328 feet (100 meters).
• Operating environment is within the ranges listed in Appendix F, “Technical Specifications.”
• Clearance to front and rear panels meets these conditions:
• Front-panel LEDs can be easily read.
• Access to ports is sufficient for unrestricted cabling.
• Front-panel direct current (DC) power connectors and the alarm connector are within reach of the
connection to the DC power source.
• Airflow around the switch must be unrestricted. To prevent the switch from overheating, you must have
the following minimum clearances:
• Top and bottom: 2.0 in. (50.8 mm)
• Sides: 2.0 in. (50.8 mm)
• Front: 2.0 in. (50.8 mm)
• Ambient temperature does not exceed 140°F (60°C).
• Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting
fixtures.
Verifying Package Contents
Included in the box is the switch itself and it’s installation documentation. If any item is missing or damaged,
contact your representative or reseller for support.
Tools and Equipment
Obtain these necessary tools and equipment:
• A single or a pair of stud size 6 ring terminals (Hollingsworth part number R3456B or equivalent) for
use as a protective ground connector.
• Crimping tool (Thomas & Bett part number WT2000, ERG-2001 or equivalent).
• 10-gauge copper ground wire.
• UL- and CSA-rated, style 1007 or 1569 twisted-pair copper appliance wiring material (AWM) wire for
DC power connections.
• Wire-stripping tools for stripping 10-, 16-, and 18-gauge wires.
• Number-2 Phillips screwdriver.
• Flat-blade screwdriver.
• 15mm 12pt socket for IP67 dust caps
Cisco Catalyst IE3400 Heavy Duty Series Hardware Installation Guide
12
Switch Installation
Verifying Package Contents