Cisco Meraki MS410 Series User manual

MS410 Series Installation Guide
About this Guide
This guide provides instruction on how to install and configure your MS410 series switch. This guide also provides
mounting instructions and limited troubleshooting procedures. For more switch installation guides, refer to
the switch installation guides section on our documentation website.
Product Overview
Models
Model number Description
MS410-16
Layer-3 16-port 1Gbe SFP and 2-port
10Gbe SFP+ aggregation switch with 1
management interface and hot-swappable power
supplies / fans
MS410-32
Layer-3 32-port 1Gbe SFP and 4-port 10Gbe
SFP+ aggregation switch with 1 management
interface and hot-swappable power supplies / fans
Physical Specifications
MS410-16 MS410-32
1GbE SFP 16 32
10GbE SFP+ uplink 2 4
40G QSFP+ Stacking ports 2 2
Dedicated Mgmt Interface 1 1
Hot Swap Power Supply Yes, Dual Yes, Dual
1

Hot Swap Fans Yes, 2x Yes, 2x
Power Input 100 - 240 VAC, 47-63 Hz 100 - 240 VAC, 47-63 Hz
Power Consumption 50-85W 50-85W
Operating Temperature 32°F - 104 °F
0°C - 40 °C
32°F - 104 °F
0°C - 40 °C
Storage and Transportation Temperature -4°F - 158°F
-20°C - 70°C
-4°F - 158°F
-20°C - 70°C
Humidity 5% to 95% 5% to 95%
Mounting 1U Rack Mount 1U Rack Mount
Product View and Physical Features
Front Panel
MS410-16 Series front panel
MS410-32 Series front panel
In addition, there is a RESTORE button available on the front panel.
Insert a paper clip if a restore is required.
• A brief, momentary press: To delete a downloaded configuration and reboot.
2

• Press and hold for more than 10 sec: To force the unit into a full factory restore.
Ports and Status Indicators
The MS uses LEDs to inform the user of the device's status. When the device powers on, the main LED will be amber.
Additional functions are described below, from left to right.
Item Function LED Status Meaning
1 Restore N/A
Restore button to clear
switch IP and local
configuration settings
2 Fan Orange
One or more of the
system fans has
malfunctioned or is
missing
3 Power (PSU) Orange
One of the system
PSUs (power supplies)
has malfunctioned or is
missing
2Status Orange
Switch is unable to or
has not yet connected
to the Meraki cloud
Flashing green Firmware upgrade in
process
White
Switch is fully
operational and
connected to the
Meraki cloud
Rainbow
Switch is booting,
searching for uplink to
Meraki Cloud
Off Switch does not have
power
3

3 Switch Port LEDs Off No client connected
Solid orange 1 Gbps on SFP+
Solid green
1 Gbps on SFP/10
Gbps on SFP+
Factory Reset Button
If the button is pressed and held for at least 10 seconds and then released, the switch will reboot and be restored to its
original factory settings by deleting all configuration information stored on the unit.
Insert a paper clip if a restore is required.
• A brief, momentary press: To delete a downloaded configuration and reboot.
• Press and hold for more than 10 sec: To force the unit into a full factory restore.
Back Panel
MS410 Series back panel
Power input Power cords may be ordered separately.
Function LED Status Meaning
Fan Orange One or more of the system fans has malfunctioned or is missing
Power (PSU) Orange One of the system PSUs (power supplies) has malfunctioned or is missing
Management Port Green Connected, used for easy access to the local status page
Equipment is to be used only in a restricted access location and installed/operated only by trained service personnel.
4

Package contents
In addition to the MS switch, the following are provided (mounting kit provided with 1U models only):
Rack Mount it includes:
▪ US 12-24 mounting screws and cage nuts, 5 of each
▪ INTL M5 mounting screws and cage nuts, 5 of each
▪ INTL M6 mounting screws and cage nuts, 5 of each
▪ Mounting washers
The MS410 series will ship with all fans and a single power supply included, additional accessories including spare fans
and power supplies can be purchased separately.
Safety and Warnings
These operations are to be taken with respect to all local laws. Please take the following into consideration for safe
operation:
• Power off the unit before you begin. Read the installation instructions before connecting the system to the power
source.
• Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with
standard practices for preventing accidents.
• Read the mounting instructions carefully before beginning installation. Failure to use the correct hardware or to
follow the correct procedures could result in a hazardous situation to people and damage to the system.
• This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective
device is rated not greater than: 15 A, 125 Vac, or 10A, 240 Vac.
• Please only power the device with the provided power cables to ensure regulatory compliance.
5

Pre-install Preparation
You should complete the following steps before going on-site to perform an installation.
Configure your Dashboard Network
The following is a brief overview only of the steps required to add a switch to your network. For detailed instructions
about creating, configuring and managing Meraki networks, refer to the online documentation
(documentation.meraki.com).
1. Login to http://dashboard.meraki.com. If this is your first time, create a new account.
2. Find the network to which you plan to add your switches or create a new network.
3. Add your switches to your network. You will need your Meraki order number (found on your invoice) or the serial
number of each switch, which looks like Qxxx-xxxx-xxxx, and is found on the bottom of the unit. You will also need
your Enterprise license key, which you should have received via email.
4. Go to the map / floor plan view and place each switch on the map by clicking and dragging it to the location where
you plan to mount it.
Check and Set Firmware
To ensure your switch performs optimally immediately following installation, it is recommended that you facilitate a
firmware upgrade prior to mounting your switch.
1. Attach your switch to power and a wired Internet connection.
2. The switch will turn on and the power LED will glow solid orange.
3. If the unit requires an upgrade, the power LED will begin blinking white until the upgrade is complete, at which
point the LED will turn solid white. You should allow at least a few minutes for the firmware upgrade to complete,
depending on the speed of your internet connection.
Check and Configure Upstream Firewall Settings
If a firewall is in place, it must allow outgoing connections on particular ports to particular IP addresses. The most
6

current list of outbound ports and IP addresses for your particular organization can be found on the firewall configuration
page in your dashboard.
Assigning an IP Address
All switches must be assigned routable IP addresses. These IP addresses can be dynamically assigned via DHCP or
statically assigned.
Dynamic Assignment
When using DHCP, the DHCP server should be configured to assign a static IP address for each MAC address
belonging to a Meraki switch. Other features of the network, such as 802.1X authentication, may rely on the property
that the switches have static IP addresses.
Static Assignment
Static IPs are assigned using the local web server on each switch. The following procedure describes how to set the
static IP:
1. Using a client machine (e.g., a laptop), connect to the switch over a wired connection.
2. Using a web browser on the client machine, access the switch’s built-in web server by browsing
to http://my.meraki.com. Alternatively, browse to http://1.1.1.100
3. Click on the “Uplink Configuration” tab. Log in. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no
password (e.g., Q2DD-551C-ZYW3).
4. Configure the static IP address, net mask, gateway IP address and DNS servers that this switch will use on its
management connection.
5. If necessary, reconnect the switch to the LAN.
Static IP via DHCP Reservations
Instead of associating to each Meraki switch individually to configure static IP addresses, an administrator can assign
7

static IP addresses on the upstream DHCP server. Through “DHCP reservations,” IP addresses are “reserved” for the
MAC addresses of the Meraki switches. Please consult the documentation for the DHCP server to configure DHCP
reservations.
Installation Instructions
Note: Each switch comes with a graphical instruction pamphlet within the box. This pamphlet contains detailed step by
step guides and images to assist in the physical install of the switch.
1. Install the mounting cage nuts in the rack being used for the switch.
2. Attach the switch face plate to the cage nuts on the rack.
8

3. Insert the power supply unit into the back of the switch. After it has been securely installed, you can connect power to
the power supply unit.
9

Mounting hardware
The mounting hardware includes integrated mounting ears for standard 1U racks. When installing the device, make sure
that there is sufficient space between the rear of the rack and other obstacles to ensure adequate airflow.
Bringing your Stack Online
The steps below explain how to prepare a group of switches for physical stacking, how to stack them together, and how
to configure the stack in Dashboard.
1. Add the switches into a Dashboard network. This can be a new Dashboard network for these switches, or an
existing network with other switches. Do not configure the stack in Dashboard yet.
10