Cisco 1262 User manual

Cisco 1262 Access Point Installation Manual 1
Cisco 1262 Wireless Access Point
Installation Manual
Content
Introduction 1
Installation 1
Installing a padlock (optional) 3
Connecting the MobileView antenna 3
Confirm access point power 4
FCC compliance 4
Contact information 4
Mounting bracket template 5
Introduction
The Cisco®Aironet®1262 Wireless Access Point is
made for interior use only.
Mount the access point in a secure location (inside
the vehicle in a secure cabinet if possible).
Ensure that the access point is in a well-ventilated
area.
Read through these instructions before installation.
Note: A qualified service person, complying with all
applicable codes, should perform all required
hardware installation.
To use this document, you must have the following
minimum qualifications:
A basic knowledge of electrical wiring and low-
voltage electrical hookups.
Installation
Before beginning, confirm you have all contents
required:
Cisco®Aironet®1262 Wireless Access Point
Mounting bracket (included with the access point)
Cisco®Aironet®1262 PoE Power Supply Unit
MobileView Wireless Antenna
Two Cat 5 Ethernet cables
Required screws and washers for mounting the access
point and power supply (not included). Mounting
hardware is included with the antenna.
Part Numbers:
MSS-MISC-WIFI-126N: Cisco®Aironet®1262 Wireless
Access Point
MSS-MISC-WIFI-PS: Cisco®Aironet®1262 Wireless
Access Point Power Supply
MSS-MISC WIFIPS-CAB: Power Supply Cable
MSS-MISC-ANT-4-240:Quad-band antenna (supports
PENTA GPS)
MSS-MISC-ANT-3-240:802.11 antenna for installations
with a MV-3000 DVR
Mounting the Access Point
A mounting bracket (see Figure 1) is included with the
access point. The mounting bracket comes detached
from the access point. The four protruded holes in the
mounting bracket are used to attach the bracket to the
mounting surface.
Note: No hardware is required to attach the access
point to the mounting bracket.

2 Cisco 1262 Access Point Installation Manual
1. Examine the access point to see how it attaches to
the mounting bracket and to ensure that the chosen
mounting location allows clearance for the network
cable connection.
Figure 1. Low-profile Mounting Bracket Installed on an access point
2. Using the mounting bracket as a guide, mark the
position of the four mounting holes on the mounting
surface. If the network cable to the access point will
be routed through the mounting surface, cut a hole
large enough for an Ethernet cable positioned under
the cable bay area of the access point.
3. Drill the 4 mounting holes with an appropriate bit for
the metal or fiberglass vehicle surface.
4. Install stainless steel rivnuts in any holes through
fiberglass. Stainless steel self-tapping screw may
be used in any holes through metal.
5. If the network cable is routed through the mounting
surface, pull about 8 in. of cable through prior to
securing the bracket to the surface.
6. Insert machine screws in the rivnut holes and self-
tapping metal screws in any holes that are drilled
directly into metal.
Install the Power Supply
1. Position the Power Supply near the DVR.
2. Secure the power supply to the rack or mounting
surface by installing appropriate screws in the
mounting holes.
3. Connect the 48 in. power cable, UTC PN MSS-
MISC-WIFI-PS-CAB, to the Access Point Power
Supply as shown in Error! Reference source not
ound. below. The green terminal block snaps into
the power supply as shown. The opposite end of
the power supply cable with the Mate-N-Lok plug
connects to the vehicle wiring harness.
NOTE: If the vehicle does not have an existing wire
harness equipped with a mating Mate-N-Lok connector
specifically to power a MobileView wireless radio at
12VDC, the connector can be removed to connect the
V+ and V- wire leads to the DVRs wiring harness (refer
to the DVR wiring pin-out diagram).
Figure 2. Connect the power cable
Connect the Network Cables
The access point has one port labeled CONSOLE and
one labeled ETHERNET. The power supply has one port
labeled IN and one labeled OUT.
1. Connect the network cable to the access point port
labeled ETHERNET.
2. Connect the other end of that same network cable to
the access point port labeled OUT.
3. Connect a network cable from the DVRs GIGIBIT
NET port to the IN port on the power supply.
4. Ensure that the network is wired correctly as shown
in Figure 3.
Figure 3. Network cable connection
5. Attach the access point to the mounting bracket,
tucking the cable into the cable bay area.

Cisco 1262 Access Point Installation Manual 3
Installing a padlock (optional)
Use the security hasp on the adapter cable access
cover and a padlock (that you provide) to secure your
access point to the mounting plate. Compatible
padlocks are Master Lock models 120T or 121T. The
cable access cover on the mounting bracket covers the
cable bay area (including the power port, Ethernet port,
console port, and mode button) to prevent access.
Follow these instructions to install the padlock:
1. With the access point installed on the mounting
bracket, insert a padlock into the security hasp.
Note: If your access point is mounted to a hard
ceiling, the clearance between the mounting bracket
and the ceiling is small. Work slowly using both hands
to position and secure the lock into the mounting
bracket hasp.
2. Rotate the lock clockwise and align the bail with the
lock body.
3. Grasp the lock and push it into the bail to lock the
lock. See Figure 4.
Figure 4. Inserting the padlock into the security hasp
4. Rotate the padlock into the padlock area. See
Figure 5.
Figure 5. Rotating the padlock into the padlock area
Connecting the MobileView antenna
The Cisco 1262 Access Point has six antenna ports:
three labeled 2.4 GHz ANTENNA as shown in Figure 6
below; and three labeled 5 GHz ANTENNA as shown in
Error! Reference source not found. below.
Figure 6. Three antenna ports labeled 2.4 GHz ANTENNA
Figure 7. Three antenna ports labeled 5 GHz ANTENNA
Each port has a black rubber protective cap, as shown in
Figure 8 below.
Figure 8. Black protective caps shown on four ports
Unless instructed otherwise for your specific installation,
remove the three protective rubber caps from the access
point ports labeled 5 GHz ANTENNA.
1. Attach the three 802.11 antenna cables to the three
5 GHz access point ANTENNA ports.
2. If the wireless antenna is part number MSS-MISC-
ANT-4-240 and the DVR is a MobileView PENTA,
connect the fourth antenna cable to the DVRs GPS
port.

4 Cisco 1262 Access Point Installation Manual
Confirm access point power
There is a small LED on the face of the access point,
shown in Figure 8 as the small black square above the
CISCO label.
When the access point is receiving power, the LED
should illuminate green. The LED may flash initially and
then become solid green. This confirms the access
point is powered on.
FCC compliance
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate access point frequency energy
and, if not installed and used in accordance with the
installation instructions, may cause harmful interference
to access point communications.
You are cautioned that any changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
Contact information
North America:
855-MOBVIEW (662-8839)
[e-mail]
Latin America:
561-998-6114
[e-mail]
Web site:
www.interlogix.com/mobileview

2013003 March 2013
© 2013 Interlogix, Inc.
Cisco is the trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries.
www.interlogix.com/mobileview
Mounting bracket template
Use the mounting bracket template to mark the positions of the mounting and cable entry holes on the mounting
surface.