Cisco Catalyst 9130 User manual

Introduction to Cisco Catalyst 9130 Access Point
with 9104 Stadium Antenna
This document describes the Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
(C-ANT9104) and provides electrical specifications and mounting instructions. The antenna is an eight-port
polarization-diverse, ultralow sidelobe patch array that operates over the 2.4-GHz and supports dual 5-GHz
Wi-Fi bands. At 5-GHz, the antenna supports beamwidth switching as well as beam steering. The antenna
supports stadiums, large public venues. It ships with an articulating mount for flat surfaces and masts and is
adjustable in horizontal and vertical planes.
• The C9130AXE-x part number is a certified indoor access point.
• The C9130AXE-STA-x bundle, consisting of the C9130AXE-x AP and C-ANT9104 antenna, is a
factory-assembled bundle and is protected from weather elements for use in indoor or outdoor
environments such as arenas and stadiums.
Note
•Technical Specifications, on page 2
•Azimuth and Elevation Radiation Patterns, on page 3
•Safety Precautions, on page 6
•Installation Notes, on page 7
•Contents of the Antenna and Bracket Kit, on page 8
•Dimensions of the Antenna and Brackets, on page 9
•Installing the Antenna, on page 12
•Mounting on a Wall or Ceiling Using Articulating Bracket, on page 14
•Mounting on a Pole or Mast, on page 17
•Grounding the Antenna, on page 18
•Connecting an Ethernet Cable to the Access Point, on page 19
•Painting the Antenna, on page 22
•Installing the Solar Shield, on page 23
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
1

Technical Specifications
IoT5-GHz Narrow
Beamwidth
20°
5-GHz Narrow
Beamwidth
10°
5-GHz Narrow
Beamwidth
Boresight
5-GHz Wide
Beamwidth
2.4-GHzParameters
50 Ohms50 Ohms50 Ohms50 Ohms50 Ohms50 OhmsNominal
Input
Impedance
2:12:12:12:12:12:1Voltage
Standing
Wave Ratio
(VSWR)
6 dBi10 dBi10 dBi10 dBi7 dBi6 dBiPeak Gain
Vertically
Polarized
Ports A, C, E,
and G are
vertically
polarized
Ports A, C, E,
and G are
vertically
polarized
Ports A, C, E,
and G are
vertically
polarized
Ports A, C, E,
and G are
vertically
polarized
Ports A and C
are vertically
polarized
Polarization
Ports B, D, F,
and H are
horizontally
polarized
Ports B, D, F,
and H are
horizontally
polarized
Ports B, D, F,
and H are
horizontally
polarized
Ports B, D, F,
and H are
horizontally
polarized
Ports B and D
are
horizontally
polarized
70°25°
25°25°80°70°3–dB
Beamwidth
Azimuth
70°25°25°25°25°70°3–dB
Beamwidth
Elevation
NA-30 dBr-30 dBr-30 dBr-21 dBrNASidelobe
Level
-15 dBr-30 dBr-30 dBr-30 dBr-20 dBr-15 dBrFront-to-Back
Ratio
RJ45 PoEConnector
Type
23.5 in. (59.70 cm)Width
18.2 in. (46.23 cm)Height
5.8 in. (14.8 cm)Depth
15.5 lbs (7.03 Kg)Weight
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
2
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Technical Specifications

IoT5-GHz Narrow
Beamwidth
20°
5-GHz Narrow
Beamwidth
10°
5-GHz Narrow
Beamwidth
Boresight
5-GHz Wide
Beamwidth
2.4-GHzParameters
IP65Water/Foreign
Body Ingress
100 mphOperational
Wind
No solar loading: -20°C to 60°C (-4°F to 140°F)
With solar loading and solar cover: up to 50°C (122°F)
Operating
Temperature
Range
-40°C to 70°C (-40°F to 158°F)Storage
Temperature
Range
Azimuth and Elevation Radiation Patterns
The following illustrations show the C-ANT9104= antenna radiation patterns:
Figure 2: C9104–Antenna Radiation Pattern Slot0 Radio (2.4-GHz
Elevation)
Figure 1: C9104–Antenna Radiation Pattern Slot0 Radio (2.4-GHz
Azimuth)
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
3
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Azimuth and Elevation Radiation Patterns

Figure 4: C9104–S1-S2 Narrow 10° Pattern (5-GHz Azimuth)Figure 3: C9104–S1-S2 Narrow 0° Pattern (5-GHz Azimuth)
Figure 6: C9104–S1-S2 Wide Radiation Pattern (5-GHz Elevation)Figure 5: C9104–S1-S2 Narrow 0° Pattern (5-GHz Elevation)
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
4
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Azimuth and Elevation Radiation Patterns

Figure 8: C9104–S1-S2 Wide Radiation Pattern (5-GHz Azimuth)Figure 7: C9104–S1-S2 Narrow 20° Pattern (5-GHz Azimuth)
Figure 10: C9104–IoT Antenna Radiation Pattern (2.4-GHz Elevation)Figure 9: C9104–IoT Antenna Radiation Pattern (2.4-GHz Azimuth)
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
5
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Azimuth and Elevation Radiation Patterns

Figure 12: C9104–AUX RF ASIC Wide Antenna Radiation Pattern
(Elevation)
Figure 11: C9104–AUX RF ASIC Wide Antenna Radiation Pattern
(Azimuth)
Safety Precautions
Installation of this antenna near power lines is dangerous. For your safety, follow the installation directions.
Danger
Each year, hundreds of people are killed or injured when attempting to install an antenna. In many of these
cases, the victim was aware of the danger of electrocution but did not take adequate steps to avoid the hazard.
For your safety and to help you achieve a sound installation, read and follow these safety precautions. They
may save your life!
• If you are installing an antenna for the first time, for your safety and that of others, seek professional
assistance. Your Cisco sales representative can explain which mounting method to use for the size and
type of antenna you are about to install.
• Select your installation site with safety and performance in mind. Remember that electric power lines
and phone lines look alike. For your safety, assume that any overhead line can kill you.
• Call your electric power company. Tell them your plans and ask them to come and look at your proposed
installation. It is a minor inconvenience considering your life is at stake.
• Plan your installation carefully and thoroughly before you begin. Successful raising of a mast or tower
is essentially a matter of coordination. Assign each person a specific task and know what to do and when
to do it. One person should be in charge of the operation to issue instructions and watch for signs of
trouble.
• When installing your antenna, remember:
•Do not use a metal ladder.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
6
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Safety Precautions

•Do not work on a wet or windy day.
•Do dress properly: shoes with rubber soles and heels, rubber gloves, long–sleeved shirt, or jacket.
• If the assembly starts to drop, get away from it and let it fall. Remember, the antenna, mast, cable, and
metal guy wires are all excellent conductors of electrical current. The slightest touch of these parts to a
power line completes an electrical path through the antenna and the installer: You!
•If any part of the antenna system should contact a power line, don’t touch it or remove it yourself. Instead,
call your local power company. They would remove it safely.
• If an accident occurs with the power lines, call for qualified emergency help immediately.
For a listing of all the warning statements and their translations, see Translated Safety Warnings for Cisco
Aironet Access Points at:
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/warnings/reference/guide/ap_warn1.html
Installation Notes
Antennas transmit and receive radio signals susceptible to RF obstructions and common sources of interference
that can reduce throughput and the range of the device connected with them. Therefore, follow these guidelines
to ensure the best possible performance:
• Keep the antenna away from metal obstructions such as:
• Heating
• Air-conditioning ducts
• Large ceiling trusses
• Building superstructures
• Major power cabling runs
If necessary, use a rigid conduit to lower the antenna away from these obstructions.
• In an outdoor environment, connect the antenna to a lightning arrestor and ensure proper grounding.
• The density of the materials used in a building’s construction determines the number of walls the signal
can pass through and maintains adequate signal strength. Consider the following before choosing the
location for your antenna:
• Signals penetrate paper and vinyl walls with little change to signal strength.
•Signals penetrate only one or two solid and precast concrete walls without degrading signal strength.
• Signals penetrate three or four concrete and woodblock walls without degrading signal strength.
•Signals penetrate five or six walls constructed of drywall or wood without degrading signal strength.
• Signals are likely to reflect off a thick metal wall and may not penetrate it at all.
• Signals are likely to reflect off a chain–link fence or wire mesh spaced between 1 and 1 1/2 inches.
(2.5 cm and 3.8 cm) The fence acts as a harmonic reflector that blocks the signal.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
7
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Installation Notes

• Install the antenna away from microwave ovens and 2-GHz cordless phones. These products can cause
signal interference because they operate in the same frequency range as the device.
• Console access using the console port
We recommend that you use a console cable that is one meter or less in length.
The AP may face issues while booting if you use an unterminated console cable
(not plugged into any device or terminal) or a console cable that is more than one
meter in length.
Note
Contents of the Antenna and Bracket Kit
Figure 13: Contents of the Antenna Bracket Kit
Tightening ValuesQuantityPartItem #
—2Mounting Flange1
—1Mounting Arm2
20.0 +/- 1.0 Nm4M8 x 20 screws3
25.0 +/- 1.0 Nm2M8 nut4
5.5 to 6.0 Nm2Hose Clamp (mast/pole mount only)5
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
8
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Contents of the Antenna and Bracket Kit

Tightening ValuesQuantityPartItem #
3.0 to 3.5 Nm2Set screws (mast/pole mount only)6
Dimensions of the Antenna and Brackets
The dimensions noted in the following illustrations are all in millimeters, unless noted otherwise.
Figure 14: Dimensions of the Antenna with Brackets and Cables
The pressure vent and mounitng screw hole locations at the back of the antenna.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
9
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Dimensions of the Antenna and Brackets

Figure 15: Locations of Screw Holes and Pressure Vent at the Back of the Antenna
The mounting hole location on the articulating mount flange.
VESA 75 mount pattern3Pressure Vent1
Tether anchor4Grounding Point2
View the assembly of the Cisco C-ANT9104 antenna with the Cisco Catalyst 9130AX AP.
Removing back plate will void product warranty.
Note
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
10
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Dimensions of the Antenna and Brackets

Figure 16: Assembly view of C-ANT9104 Antenna
Back plate4Cisco C-ANT9104 Antenna1
Ethernet and Console jumper cables5DART cable connecting the C9130AX
AP with the C-ANT9104 Antenna
2
Cisco Catalyst 9130AX AP3
Figure 17: Locations of the Screw Holes on the Articulating Mount Flange
Pole / Mast mounting set screw holes1
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
11
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Dimensions of the Antenna and Brackets

Slotted holes for hose clamps2
Installing the Antenna
You can install the antenna on a wall or ceiling (must be a flat surface) or on a pole with a minimum diameter
of 2 inches (5.08 cm) and a maximum diameter of 5 inches (12.7 cm).
Procedure
Step 1 Decide on a mounting location.
See Deciding on a Mounting Location, on page 12.
Step 2 Ensure that you have the required tools and fasteners ready
See Required Tools and Equipment, on page 13.
Step 3 Proceed with mounting the antenna.
When mounting the antenna:
a. Assemble the bracket hardware.
b. Connect the antenna and the bracket to the mounting surface.
c. Secure the antenna using the tether anchor (tether strap not included).
d. Connect the antenna to ground using the included ground screw and Electrical Joint Compound.
e. Adjust the antenna orientation.
The mounting options available are:
•Mounting on a Wall or Ceiling Using Articulating Bracket, on page 14
•Mounting on a Pole or Mast
Step 4 (Optional) Paint the antenna.
See Painting the Antenna, on page 22.
Step 5 Install a Solar Shield.
See Installing the Solar Shield, on page 23.
Deciding on a Mounting Location
The antenna should be mounted clear of any obstructions to the side or front of the enclosure, which contains
the radiating elements. Remember to aim this antenna at the intended coverage area. Therefore, you should
mount the antenna and adjust it to achieve the desired mechanical tilt.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
12
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Installing the Antenna

As with all the outdoor installations, you must install the antenna with cables exiting downward which helps
prevent water from accumulating around the cable exit points.
Caution
Required Tools and Equipment
IMPORTANT SAFETY INSTRUCTIONS Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for preventing accidents. Read the
installation instructions before using, installing, or connecting the system to the power source. Use the statement
number provided at the end of each warning statement to locate its translation in the translated safety warnings
for this device.SAVE THESE INSTRUCTIONS Statement 1071
Danger
Only skilled person should be allowed to install, replace, or service this equipment. Refer to Statement
1089 for description of skilled person. Statement 1090
Danger
To reduce the risk of electric shock, refer to national and local codes for proper installation and
grounding of antennas. Statement 1052
Danger
To reduce the risk of electric shock, the chassis of this equipment needs to be connected to permanent
earth ground during normal use. Statement 0445
Danger
The fasteners and the mounting surface should be capable of maintaining a minimum pullout force of 150
pounds (68 kg) to support the weight of the antenna and bracket, along with the potential wind loading on the
antenna.
Caution
The pole or mast must be rigid enough to hold the weight of the antenna along with the associated forces
produced by wind loads. Also, the pole or mast must be structurally strong enough to withstand the clamping
force of the hose clamps.
Caution
Before you mount the antenna, go through the supported mounting procedures and ensure that you have all
tools and fasteners mentioned therein ready. The following is a general list of fasteners and tools not included
in the antenna and brackets kit:
• To mount the antenna on a wall or ceiling, you need four mounting M8 screws or bolts and wall anchors.
• To mount the antenna on a pole or mast, you may need either or both of these supplies:
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
13
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Required Tools and Equipment

• A slotted screwdriver or a wrench to tighten the screws on the hose clamps
• A Hex key to tighten set screws
Mounting on a Wall or Ceiling Using Articulating Bracket
Tether antenna assembly and mounting hardware to a secure mounting surface using the tether anchor on the
antenna. The mounting kit does not include the tether strap.
Note
Figure 18: Exploded View of Antenna and Bracket Hardware Assembly
Tightening ValuesQuantityMounting Bracket KitItem
#
—2Mounting flange1
—1Mounting arm2
20.0 +/- 1.0 Nm4M8 x20 screws3
25.0 +/- 1.0 Nm2M8 nut4
5.5 Nm to 6 Nm2Hose clamp (mast/pole mount only)5
3.0 Nm to 3.5 Nm2Set screws (mast/pole mount only)6
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
14
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Mounting on a Wall or Ceiling Using Articulating Bracket

Figure 19: Close-Up View of the Azimuth and Elevation-Adjustment Pivots
Figure 20: Azimuth Adjustment
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
15
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Mounting on a Wall or Ceiling Using Articulating Bracket

Figure 21: Elevation Adjustment
Procedure
Step 1 Determine the mounting location for the antenna.
Step 2 Attach one of the mount flanges to the wall or ceiling using four M8 screws through the holes in the bracket.
The mounting kit includes the mount flanges. See Figure 13: Contents of the Antenna Bracket Kit, on page
8.
The mounting kit does not include the M8 screws for securing the bracket to the mounting surface.
Note
Step 3 Attach the other mount flange to the back of the antenna using four M8 screws through the holes in the bracket.
Tighten the screws to 20.0 +/- 1.0 Nm torque.
Step 4 Assemble the mounting arm to the flanges.
Use a wrench to tighten all screws and nuts. See Figure 18: Exploded View of Antenna and Bracket Hardware
Assembly, on page 14.
Step 5 Orient the antenna correctly so that the antenna cable exits downwards.
Use a wrench to loosen or tighten the fasteners at the azimuth and elevation- adjustment pivots.
Step 6 Adjust the azimuth (side-to-side position) and elevation (up-and-down position) of the antenna.
Loosen the adjustment pivot nuts slightly to allow for adjustment. Use the azimuth and elevation markings
on the articulating mounting arm and the flange brackets as a guide. See Figure 19: Close-Up View of the
Azimuth and Elevation-Adjustment Pivots, on page 15. You may adjust the azimuth angle up to ±60 degrees,
see Figure 20: Azimuth Adjustment, on page 15, and elevation up to ±60 degrees see Figure 21: Elevation
Adjustment, on page 16.
Step 7 After adjusting the antenna position, tighten the pivot nuts.
Tighten all nuts at the pivot points to 25.0 +/- 1.0 Nm torque.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
16
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Mounting on a Wall or Ceiling Using Articulating Bracket

Step 8 Connect the Ethernet cable to the antenna using the termination kit.
Step 9 Connect the antenna to the building ground using the grounding kit.
Mounting on a Pole or Mast
Figure 22: Antenna Bracket Hose Clamp Assembly for Pole Mounting
Articulating mount flange that is fastened to the
pole or mast using hose clamps
3Worm-gear-type hose clamp (50–135mm) for
mounting the assembly on a pole or mast
1
Articulating mount arm4Screws holes to mount the assembly to a wall.2
Before you begin
The pole or mast must be rigid enough to hold the weight of an antenna along with the associated forces
produced by wind loads. In addition, the mast must be structurally strong enough to withstand the clamping
force of the hose clamps.
Note
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
17
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Mounting on a Pole or Mast

Procedure
Step 1 Determine the mounting location for the antenna on the pole or mast.
Step 2 Position and mount the mounting flange bracket onto the pole or mast using the hose clamps provided in the
kit.
The hose clamps should pass through the slots on the free mounting flange bracket.
Step 3 Tighten the hose clamps and set screws until the antenna is fully secure on the mast.
Then, adjust the antenna to its final position. Then, use a slotted screwdriver to tighten the screws on the hose
clamps.
Step 4 Attach the other mount flange through the holes in the bracket to the back of the antenna using four M8 screws.
The mounting kit includes the mounting flange and M8 screws. Tighten the screws to 20.0 +/- 1.0 Nm torque.
Step 5 Assemble the mounting arm to the flanges.
Use a wrench to tighten all screws and nuts.
Step 6 Ensure that the antenna cannot rotate about the mast.
Step 7 Adjust the azimuth (side-to-side position) and the antenna’s elevation (up-and-down position).
Loosen the adjustment pivot nuts slightly to allow for adjustment.
You can use the azimuth and elevation markings on the articulating mounting arm and the flange brackets as
a guide. See Figure 19: Close-Up View of the Azimuth and Elevation-Adjustment Pivots, on page 15. You
can adjust the azimuth angle up to ±50 degrees, see Figure 20: Azimuth Adjustment, on page 15, and elevation
up to ±50 degrees see Figure 21: Elevation Adjustment, on page 16.
Step 8 After adjusting the antenna position, tighten all nuts at the pivot points to 25.0 +/- 1.0 Nm torque.
Step 9 Connect the Ethernet cable to the antenna using the termination kit.
Grounding the Antenna
The antenna must be grounded before connecting power.
Procedure
Step 1 Install grounding standoff included in the solar shield kit when the optional solar cover is used.
Use the included Electrical Joint Compound on both ends of grounding standoff and tighten the standoff to
10.2 +/- 1.0 kgf-cm of torque.
Step 2 Connect the antenna to building ground with the included ground screw and included Electrical Joint Compound.
Tighten the ground screw to 10.2 +/- 1.0 kgf-cm of torque.
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
18
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Grounding the Antenna

Connecting an Ethernet Cable to the Access Point
Installing a CAT 5e Ethernet Cable and Gland Assembly to the Access Point
Figure 23: CAT 5e Cable Gland Assembly
Screw nut4CAT 5e RJ45 Plug1
Seal5Gasket2
Thread-lock sealing nut6Clamp ring3
Before you begin
You must supply these tools and materials:
• Shielded outdoor-rated CAT 5e Ethernet cable with a diameter of 0.2 to 0.35 inch (5 to 9 mm)
• CAT 5e RJ-45 connector and installation tool
• Adjustable wrench or 28–mm box wrench
Procedure
Step 1 Disconnect power to the power injector and ensure all power sources to the AP are turned off.
Thisunit might havemorethan one powersupply connection. All connections must be removed
to de-energize the unit. Statement 1028
Danger
Step 2 Ensure a 6 AWG ground wire is connected to the AP (see Grounding the Antenna, on page 18).
Step 3 Remove the covering cap from the PoE port.
Step 4 Loosen and remove the cable sealing nut of the cable gland by turning it counterclockwise.
Verify that the cable gland has a rubber seal and ensure that it is not damaged.
Note
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
19
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Connecting an Ethernet Cable to the Access Point

If the cable gland and rubber gasket is not installed correctly, it causes the cable grip to leak.
Caution
Step 5 Insert the Ethernet cable's unterminated end through the sealing nut end of the cable gland.
Pass the Ethernet cable through the appropriate size cable seal and pull several inches of cable through the
adapted components.
Step 6 Install an RJ-45 connector on the Ethernet cable's unterminated end using your Ethernet cable installation
tool.
Step 7 Carefully connect the RJ45 cable connector to the PoE port on the AP.
Step 8 Slide the cable gland with the rubber seal towards the AP and screw the threaded end of the body into the AP,
and hand-tighten.
Step 9 Use an adjustable wrench or a 28–mm wrench to tighten the body's threaded end into the enclosure. Tighten
to 15 lbf-in (17 kgf-cm) of torque.
Step 10 Use an adjustable wrench and tighten the thread-lock seal nut to 15 lbf-in (17 kgf-cm) of torque.
Step 11 Route your Ethernet cable and cut off any excess cable.
Step 12 Install an RJ45 connector on the unterminated cable end and insert it into the power injector.
Step 13 Turn on the power to the power injector.
Installing a CAT 6/6A Ethernet Cable and Gland Assembly to the Antenna
Figure 24: CAT 6/6a Cable Gland Assembly
Screw nut5CAT 6/6A RJ45 Plug1
Cable Seal (Cable OD range 5 mm to 7 mm)6RJ45 wire load bar
Note the orientation into plug
2
Cable Seal (Cable OD range 7 mm to9 mm)7Gasket3
Cable sealing nut8Clamp ring4
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
20
Introduction to Cisco Catalyst 9130 Access Point with 9104 Stadium Antenna
Installing a CAT 6/6A Ethernet Cable and Gland Assembly to the Antenna