Cisco Aironet 1570 Series Manual

CHAPTER
2-1
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
2
Preparing for Installation
This chapter provides the safety warnings, guidelines and related information which you must follow
before starting with the installation of the access point. These sections are included in this chapter:
•Safety Warnings, page 2-2
•FCC Safety Compliance Statement, page 2-4
•Safety Precautions, page 2-4
•Access Point Installation Guidelines, page 2-5
•Safety Precautions when Installing Antennas, page 2-6
•Safety Instructions for Antennas and Radios, page 2-7
•Avoiding Damage to Radios in a Testing Environment, page 2-7
•Safety Instructions for Powering the Access Point, page 2-8
•Translated Safety Warnings, page 2-9

2-2
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Safety Warnings
Safety Warnings
To see translated versions of all safety warnings, browse to the document on Cisco.com, see Translated
Safety Warnings, page 2-9 for instructions.
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before
you work on any equipment, be aware of the hazards involved with electrical circuitry and be
familiar with standard practices for preventing accidents. Use the statement number provided at
the end of each warning to locate its translation in the translated safety warnings that
accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning This equipment is to be installed by trained and qualified personnel, as per these installation
instructions. The installer is responsible for obtaining any required local or national safety
inspections of the structural integrity of the installation by the local authority/inspection
department.
Warning Do not operate the unit near unshielded blasting caps or in an explosive environment unless the
device has been modified to be especially qualified for such use. Statement 364
Warning The cables specified in this installation guide that are used with the specified cable glands provide
protection against ingress of moisture for a Type 4/IP67 classified enclosure. If substitute cable
are used, the installer must ensure that the size (OD) of the cable meets the acceptable range
allowed by the cable gland.
Warning This equipment must be externally grounded using a customer-supplied ground wire before
power is applied. Contact the appropriate electrical inspection authority or an electrician if you
are uncertain that suitable grounding is available. Statement 366
Warning Read the installation instructions before connecting the system to the power source. Statement
1004
Warning Ultimate disposal of this product should be handled according to all national laws and
regulations. Statement 1040
Caution All installation methods for mounting an access point on any wall surface is subject to the acceptance of
local jurisdiction.

2-3
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Safety Warnings
Warning Only trained and qualified personnel should be allowed to install, replace, or service this
equipment. Statement 1030
Warning Installation of the equipment must comply with local and national electrical codes. Statement
1074
Warning Installation of the equipment must comply with local and national electrical codes. Statement
1074
Warning In order to comply with radio frequency (RF) exposure limits, see Appendix B, “Declarations of
Conformity and Regulatory Information”, to find the safe operating distance as required for
your local regulatory domain. Statement 339
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring.
Statement 1022
Warning Installation of the equipment must comply with local and national electrical codes. Statement
1074
Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement
1023
Warning This unit might have more than one power supply connection. All connections must be removed
to de-energize the unit. Statement 1028
Warning Only trained and qualified personnel should be allowed to install, replace, or service
this equipment. Statement 1030
Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)
requirements in IEC 60950 based safety standards. Statement 1033

2-4
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
FCC Safety Compliance Statement
Warning When installing or replacing the unit, the ground connection must always be made first and
disconnected last. Statement 1046.
Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical
Code, Section 54). Statement 1052
Caution Before connecting or disconnecting a power cord, you must remove power from the power cord using a
suitable service disconnect.
FCC Safety Compliance Statement
The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF
electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet
antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI
C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results
in user exposure substantially below the FCC recommended limits.
Safety Precautions
For safety and to achieve a good installation, please read and follow these safety precautions:
•Select your installation site with safety, as well as performance in mind. Remember: electric power
lines and phone lines look alike. For safety, assume that any overhead line can kill.
•Call your electric power company. Tell them your plans, and ask them to come look at your proposed
installation.
•Plan your installation carefully and completely before you begin. Successful raising of a mast or
tower is largely a matter of coordination. Each person should be assigned to a specific task and
should know what to do and when to do it. One person should be in charge of the operation to issue
instructions and watch for signs of trouble.
•When installing the access point and antennas, remember:
– Do not use a metal ladder.
– Do not work on a wet or windy day.
– Do dress properly—shoes with rubber soles and heels, rubber gloves, long sleeved shirt or
jacket.
•Use a rope to lift the access point. If the assembly starts to drop, get away from it and let it fall.
•If any part of the antenna system should come in contact with a power line, do not touch it or try to
remove it yourself. Call your local power company. They will remove it safely.
If an accident should occur, call for qualified emergency help immediately.

2-5
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Access Point Installation Guidelines
Access Point Installation Guidelines
Personnel installing the access point must understand wireless access points and bridging techniques and
grounding methods.
Because the access point is a radio device, it is susceptible to common causes of interference that can
reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:
•Review the FCC guidelines for installing and operating outdoor wireless LAN devices at
http://www.cisco.com/c/en/us/products/collateral/routers/3200-series-rugged-integrated-services-r
outers-isr/data_sheet_c78-647116.html
•Perform a site survey before beginning the installation.
•Install the access point in an area where structures, trees, or hills do not obstruct radio signals to and
from the access point.
•The access points can be installed at any height, but best throughput is achieved when all the access
points are mounted at the same height. We recommend installing the access points no higher than
40 feet to allow support for wireless clients on the ground.
Note To calculate path loss and to determine how far apart to install access points, consult an RF planning
expert.
Site Surveys
Every network application is a unique installation. Before installing multiple access points, you should
perform a site survey to determine the optimum use of networking components and to maximize range,
coverage, and network performance.
Site surveys reveal problems that can be resolved before the network is operational. Because
802.11a/b/g/n/ac operates in an unlicensed spectrum, there may be sources of interference from other
802.11a wireless devices (especially in multi-tenant buildings) that could degrade your 802.11 signals.
A site survey can determine if such interference exists at the time of deployment.
A proper site survey involves temporarily setting up mesh links and taking measurements to determine
whether your antenna calculations are accurate. Determine the correct locations and antenna types
before you drill holes and route cables and mounting equipment.
Consider the following operating and environmental conditions when performing a site survey:
•Data rates—Sensitivity and range are inversely proportional to data bit rates. The maximum radio
range is achieved at the lowest workable data rate. A decrease in receiver sensitivity occurs as the
radio data increases.
•Antenna type and placement—Proper antenna configuration is a critical factor in maximizing radio
range. As a general rule, range increases in proportion to antenna height. However, do not place the
antenna higher than necessary, because the extra height also increases potential interference from
other unlicensed radio systems and decreases the wireless coverage from the ground.
•Physical environment—Clear or open areas provide better radio range than closed or filled areas.
•Obstructions—Physical obstructions such as buildings, trees, or hills can hinder performance of
wireless devices. Avoid locating the devices in a location where there is an obstruction between the
sending and receiving antennas.
•How far is your wireless link?

2-6
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Safety Precautions when Installing Antennas
•Has a previous site survey been conducted?
•Do you have a clear Fresnel zone between the access points or radio line of sight?
•What is the minimum acceptable data rate within the link?
•Do you have the correct antenna (if more than one antenna is being offered?)
•Do you have access to both of the mesh site locations?
•Do you have the proper permits, if required?
•Are you following the proper safety procedures and practices?
•Have you configured the access points before you go onsite? It is always easier to resolve
configurations or device problems first.
•Do you have the proper tools and equipment to complete your survey.
Before Beginning the Installation
Before you begin the installation process:
•Ensure that a site survey has been performed.
•Ensure that your network infrastructure devices are operational and properly configured.
•Ensure that your controllers are connected to switch trunk ports.
•Ensure that your switch is configured with untagged access ports for connecting your access points.
•Ensure that a DHCP server with Option 43 configured is reachable by your access points, or
manually configure the controller information in the access point (for additional information, refer
to the “Configuring DHCP Option 43” section on page D-1).
•Become familiar with the access point installation components.
Safety Precautions when Installing Antennas
Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, as they may cause serious injury or death. For proper
installation and grounding of the antenna, please refer to national and local codes (e.g. U.S.:
NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54).
Statement 280
1. Before you install an antenna, contact your Cisco account representative to explain which mounting
method to use for the size and type of antenna that you are about to install.
2. Select your installation site with safety, as well as performance, in mind. Remember that electric
power lines and phone lines look alike. For your safety, assume that any overhead line can kill you.
3. Contact your electric power company. Tell them your plans and ask them to come look at your
proposed installation.
4. Plan your installation carefully and completely before you begin. Each person involved in an
installation should be assigned to a specific task and should know what to do and when to do it. One
person should be in charge of the operation to issue instructions and watch for signs of trouble.

2-7
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Safety Instructions for Antennas and Radios
5. When installing your antenna, follow these guidelines:
– Do not use a metal ladder.
– Do not work on a wet or windy day.
– Do dress properly—wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved
shirt or jacket.
6. If the assembly starts to drop, move away from it and let it fall. Because the antenna, mast, cable,
and metal guy wires are all excellent conductors of electrical current, even the slightest touch of any
of these parts to a power line completes an electrical path through the antenna and the installer.
7. If any part of the antenna system should come in contact with a power line, do not touch it or try to
remove it yourself. Call your local power company to have it removed safely.
8. If an accident should occur with the power lines, call for qualified emergency help immediately.
Safety Instructions for Antennas and Radios
Warning In order to comply with radio frequency (RF) exposure limits, see Appendix B, “Declarations of
Conformity and Regulatory Information”, to find the safe operating distance as required for
your local regulatory domain. Statement 339
Warning Do not locate the antenna near overhead power lines or other electric light or power circuits, or
where it can come into contact with such circuits. When installing the antenna, take extreme care
not to come into contact with such circuits, because they may cause serious injury or death. For
proper installation and grounding of the antenna, please refer to national and local codes (for
example, U.S.: NFPA 70, National Electric Code, Article 180, Canada: Canadian Electrical Code,
Section 54). Statement 1052
Warning Only trained and qualified personnel should be allowed to install, replace, or service this
equipment. Statement 1030
Avoiding Damage to Radios in a Testing Environment
The radios on outdoor units (bridges) have higher transmit power levels than radios on indoor units
(access points). When you test high-power radios in a link, you must avoid exceeding the maximum
receive input level for the receiver. At levels above the normal operating range, packet error rate (PER)
performance is degraded. At even higher levels, the receiver can be permanently damaged. To avoid
receiver damage and PER degradation, you can use one of the following techniques:
•Separate the omnidirectional antennas by at least 2 ft (0.6 m) to avoid receiver damage or by at least
25 ft (7.6 m) to avoid PER degradation.
Note These distances assume free space path loss and are conservative estimates. Required separation
distances for damage and performance degradation levels in actual deployments are less if
conditions are not non-line-of-sight.

2-8
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Safety Instructions for Powering the Access Point
•Reduce the configured transmit power to the minimum level.
•Use directional antennas, and keep them away from each other.
•Cable the radios together using a combination of attenuators, combiners, or splitters to achieve a total
attenuation of at least 60 dB.
For a radiated test bed, the following equation describes the relationships among transmit power, antenna
gain, attenuation, and receiver sensitivity:
txpwr + tx gain + rx gain - [attenuation due to antenna spacing] < max rx input level
Where:
txpwr = Radio transmit power level
tx gain = transmitter antenna gain
rx gain = receiver antenna gain
For a conducted test bed, the following equation describes the relationships among transmit power,
antenna gain, and receiver sensitivity:
txpwr - [attenuation due to coaxial components] < max rx input level
Caution Under no circumstances should you connect the antenna port from one access point to the antenna port
of another access point without using an RF attenuator. If you connect antenna ports, you must not
exceed the maximum survivable receive level of 0 dBm. Never exceed 0 dBm, or damage to the access
point can occur. Using attenuators, combiners, and splitters having a total of at least 60 dB of attenuation
ensures that the receiver is not damaged and that PER performance is not degraded.
Safety Instructions for Powering the Access Point
Warning Installation of the equipment must comply with local and national electrical codes. Statement
1074
Warning This equipment must be externally grounded using a customer-supplied ground wire before
power is applied. Contact the appropriate electrical inspection authority or an electrician if you
are uncertain that suitable grounding is available. Statement 366
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning Installation of the equipment must comply with local and national electrical codes. Statement
1074

2-9
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Translated Safety Warnings
Warning This equipment must be externally grounded using a customer-supplied ground wire before
power is applied. Contact the appropriate electrical inspection authority or an electrician if you
are uncertain that suitable grounding is available. Statement 366
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)
requirements in IEC 60950 based safety standards. Statement 1033
Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement
1023
Caution Power injectors must be used indoors only. Do not place a power injector in an unprotected outdoor
environment because water could get into the power injector and cause a short circuit and possible fire.
Caution When the access point is installed outdoors or in a wet or damp location, the AC branch circuit that is
powering the access point should be provided with ground fault protection (GFCI), as required by Article
210 of the National Electrical Code (NEC).
Translated Safety Warnings
The document containing the Translated Safety Warnings for Cisco Aironet 1570 Series Outdoor Access
Points is provided on the following page on Cisco.com:
http://www.cisco.com/c/en/us/products/collateral/wireless/bulletin-c25-735595.html

2-10
Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide
OL-32138-01
Chapter 2 Preparing for Installation
Translated Safety Warnings