Citrix ByteMobile T1010 Quick guide

T-Series Traffic Director Install, Admin & Config Guide
ByteMobile T1000 Traffic Director
Installation, Configuration, and Administration Guide
Model T1010, T1100 and T1200
Release 1.0
Rev. H
Document Part Number: 707-00045-00
Printed: June 18, 2013
SAFETY NOTICE
The product described in this document has safety considerations.
Before installing or maintaining this product, please read the
instructions in the “Safety Information” section on page iii. Failure to
follow the safety instructions in this document may result in injury
to self and others, or may cause property damage.

© 2013 Citrix Systems, Inc. All Rights Reserved.
The information contained herein is the exclusive property of Citrix Systems, Inc. No part of this manual may be disclosed
or reproduced in whole or in part, be copied, photocopied, translated, or reduced to any electronic medium or machine
readable form without prior consent, in writing, from Citrix Systems, Inc.
Printed in the United States of America.
Disclaimer
The information in this document is subject to change without notice and should not be construed as a commitment by Citrix
Systems, Inc. Citrix assumes no responsibility for any errors that may appear in this document.
Trademarks
Citrix, ByteMobile, the ByteMobile logo, Smart Capacity, Smart Capacity at the Core, Macara, Monaco, Unison, Media
Fidelity, Web Fidelity, and Dynamic Interleaving are trademarks of Citrix Systems, Inc., or a subsidiary thereof, and are or
may be registered in the U.S. Patent and Trademark Office and other countries. All other trademarks are the property of their
respective owners.

T-Series Traffic Director Installation, Configuration and Administration Guide iii
Safety
Safety Information
Before using the information in this document and the product it supports, read the
information in this section, and the “Technical Assistance” section on page xix.
Before Installing
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.

iv T-Series Traffic Director Installation, Configuration and Administration Guide
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Safety Statements
These statements provide the caution and danger information used in this documentation.
Important: Each caution and danger statement in this documentation is labeled with a
number. This number is used to cross reference an English-language caution or
danger statement with translated versions of the caution or danger statement in
the Safety Information document.
For example, if a caution statement is labeled “Statement 1,” translations for
that caution statement are in the Safety Information document under
“Statement 1.”
Be sure to read all caution and danger statements in this documentation before
you perform the procedures. Read any additional safety information that comes
with your system or optional device before you install the device.
Statement 1
Danger: Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
•Do not connect or disconnect any cables or perform installation, maintenance,
or reconfiguration of this product during an electrical storm.
•Connect all power cords to a properly wired and grounded electrical outlet.
•Connect to properly wired outlets any equipment that will be attached to this
product.
•When possible, use one hand only to connect or disconnect signal cables.
•Never turn on any equipment when there is evidence of fire, water, or structural
damage.
•Disconnect the attached power cords, telecommunications systems, networks,
and modems before you open the device covers, unless instructed otherwise in
the installation and configuration procedures.

T-Series Traffic Director Installation, Configuration and Administration Guide v
•Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
Statement 3
Caution: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
•Do not remove the covers. Removing the covers of the laser product could result in
exposure to hazardous laser radiation. There are no serviceable parts inside the
device.
•Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
Danger: Some laser products contain an embedded Class 3A or Class 3B laser diode.
Note the following:
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
To Connect: To Disconnect:
1. Turn OFF all power sources and
equipment to be attached to this
product.
2. Attach all cables to the devices.
3. Attach signal cables to the
connectors.
4. Attach power cords to power
sources. For DC systems, ensure
correct polarity of -48VDC
connections: RTN is (+) and
-48VDC is (-). Earth ground should
use a two-hole lug for safety.
5. Turn ON all the power sources.
1. Turn OFF all power sources and
equipment to be attached to this
product.
•For AC systems, remove all power
cords from the shelf power
receptacles or interrupt power at the
ac power distribution unit.
•For DC system systems, disconnect
DC power sources at the breaker
panel or by turning off the power
source, then remove the DC cables.
2. Remove the signal cables from the
connectors.
3. Remove all cables from the devices
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A Laser de Classe 1
`

vi T-Series Traffic Director Installation, Configuration and Administration Guide
Statement 8
Caution: Never remove the cover on a power supply or any part that has the
following label attached.
Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no serviceable parts
inside these components. If you suspect a problem with one of these parts,
contact a service technician.
Statement 12
Caution: The following label indicates a hot surface nearby.
Statement 13
Danger: Overloading a branch circuit is potentially a fire hazard and a shock hazard
under certain conditions. To avoid these hazards, ensure that your system
electrical requirements do not exceed branch circuit protection requirements.
Refer to the information that is provided with your device for electrical
specifications.
Statement 29 (DC Models Only)
Caution: This equipment is designed to permit the connection of the earthed conductor of
the DC supply circuit to the earthing conductor at the equipment. If this
connection is made, all of the following conditions must be met:

T-Series Traffic Director Installation, Configuration and Administration Guide vii
•This equipment shall be connected directly to the DC supply system earthing
electrode conductor or to a bonding jumper from an earthing terminal bar or bus to
which the DC supply system earthing electrode conductor is connected.
•This equipment shall be located in the same immediate area (such as, adjacent
cabinets) as any other equipment that has a connection between the earthed
conductor of the same DC supply circuit and the earthing conductor, and also the
point of earthing of the DC system. The DC system shall not be earthed elsewhere.
•The DC supply source shall be located within the same premises as this equipment.
•Switching or disconnecting devices shall not be in the earthed circuit conductor
between the DC source and the point of connection of the earthing electrode
conductor.
Statement 31
Danger: Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
•Do not connect or disconnect any cables or perform installation, maintenance,
or reconfiguration of this product during an electrical storm.
•Connect all power cords to a properly wired and grounded electrical outlet.
•Connect to properly wired outlets any equipment that will be attached to this
product.
•When possible, use one hand only to connect or disconnect signal cables.
•Never turn on any equipment when there is evidence of fire, water, or structural
damage.
•Disconnect the attached power cords, telecommunications systems, networks,
and modems before you open the device covers, unless instructed otherwise in
the installation and configuration procedures.
•Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.

viii T-Series Traffic Director Installation, Configuration and Administration Guide
Statement 33
To Connect: To Disconnect:
1. Turn OFF all power sources and
equipment to be attached to this
product.
2. Attach all cables to the devices.
3. Attach signal cables to the
connectors.
4. Attach power cords to power
sources. For DC systems, ensure
correct polarity of -48VDC
connections: RTN is (+) and
-48VDC is (-). Earth ground should
use a two-hole lug for safety.
5. Turn ON all the power sources.
1. Turn OFF all power sources and
equipment to be attached to this
product.
•For AC systems, remove all power
cords from the shelf power
receptacles or interrupt power at the
ac power distribution unit.
•For DC system systems, disconnect
DC power sources at the breaker
panel or by turning off the power
source, then remove the DC cables.
2. Remove the signal cables from the
connectors.
3. Remove all cables from the devices
Caution: This device does not provide a power control button. Removing power supply
modules or turning off the unit does not turn off the electrical current supplied to the
device. The device also might have more than one power cord. To remove all electrical
current from the device, ensure that all power cords are disconnected from the power
source.
T1000 DC Power Option:
T1000 AC Power Option:
OFF
1 2

T-Series Traffic Director Installation, Configuration and Administration Guide ix
Statement 34
Fiber Optic Safety Information, Statement 1
Caution: To reduce the risk of electric shock or energy hazards:
•This equipment must be installed by trained service personnel in a
restricted-access location, as defined by the NEC and IEC 60950-1, First
Edition, The Standard for Safety of Information Technology Equipment.
•Connect the equipment to a properly grounded safety extra low voltage
(SELV) source. A SELV source is a secondary circuit that is designed so
that normal and single fault conditions do not cause the voltages to
exceed a safe level (60 V direct current).
•Incorporate a readily available approved and rated disconnect device in
the field wiring.
•See the specifications in the product documentation for the required
circuit-breaker rating for branch circuit overcurrent protection.
•Use copper wire conductors only. See the specifications in the product
documentation for the required wire size.
•See the specifications in the product documentation for the required
torque values for the wiring-terminal nuts.
Danger: Hazardous Radiation
Fiber optic products use laser radiation with the potential to cause injury. Uncovered
ports may release this radiation. Avoid direct exposure to laser radiation. Do not stare
into the beam, and do not view directly with optical instruments. Do not remove any
protective shields on fiber optic transceiver modules.

x T-Series Traffic Director Installation, Configuration and Administration Guide

Table of Contents
T-Series Traffic Director Installation, Configuration and Administration Guide xi
Safety Information
Before Installing iii
Safety Statements iv
About This Guide
Objective xv
Audience xv
Organization xvi
T-Series Related Documents xvi
Unison Related Documents xvii
Citrix NetScaler Documents xvii
Revision History xvii
Document Conventions xviii
Notices and Statements in this Document xix
Documentation Feedback xix
Technical Assistance xix
Chapter 1 Introduction
Traffic Director Architecture 1-2
Product Capabilities 1-4
Hardware Overview 1-8
Common Hardware Features 1-11
Chapter 2 Installing the T1000
Overview of Installing T1000 2-1
Cautions and Warnings 2-2
Preparing for Installation 2-4
Handling Static-Sensitive Devices 2-6
Unpacking the Shipping Container 2-7
Table of Contents

Contents
xii T-Series Traffic Director Installation, Configuration and Administration Guide
Rack Mounting the T1000 2-8
Making Data Plane Connections 2-11
Making Management Connections 2-18
Connecting and Disconnecting AC Power 2-19
Connecting and Disconnecting DC Power 2-22
Accessing and Configuring the Management Plane 2-29
Accessing and Configuring the LOM Port 2-31
Chapter 3 Basic T1000/Unison Load-Balancing Configuration
Physical Integration of T1000 with Unison 3-2
Managing Configurations 3-3
Assigning VLANs, IP Addresses, and Ports 3-4
Configuring T1000 Basic Functions 3-8
Configuring T1000 Data Plane for Layer-2 and Layer-3 3-11
Configuring T1000 Load Balancing 3-17
Configuring Health Checks and Redundancy 3-22
Configuring Source NAT (SNAT) 3-26
Configuring Security 3-27
Testing with Network Diagnostic and Shell Tools 3-29
Chapter 4 Dynamic Routing Protocol Configuration for T1000/Unison
Overview 4-1
OSPF Protocol and Setup 4-1
OSPF Configuration 4-2
Chapter 5 Administration
Using the T1000 Command Line Interface (CLI) 5-1
Using the T1000 Graphical User Interface (GUI) 5-2
Lights-Out Management 5-4
Upgrading the T1000 Operating System 5-4
Installing/Upgrading T1000 License 5-7
Authentication and Authorization 5-9
Configuring SNMP 5-15
Collecting Real-Time Statistics from the CLI 5-23
Advanced Administration 5-23
Appendix A T1000 Specifications
Environmental Specifications A-1
Power Characteristics A-2
Physical Characteristics A-3
Regulatory Compliance A-4

T-Series Traffic Director Installation, Configuration and Administration Guide xiii
Contents
Appendix B Replacement Parts
Replaceable Components List B-1
Replacing an AC Power Supply B-2
Replacing a DC Power Supply B-4
Appendix C Legal Notices
Legal Notice C-1
Trademarks C-2
Third-Party Disclosures C-2
Important Notes C-2
Product Recycling and Disposal C-3
Battery Return Program C-3
Electronic Emission Notices C-4
Index

Contents
xiv T-Series Traffic Director Installation, Configuration and Administration Guide

T-Series Traffic Director Installation, Configuration and Administration Guide xv
About This Guide
We are pleased that you have chosen the Bytemobile T1000 Traffic Director. As a network
element in the T-Series architecture, the T1000 Traffic Director intelligently load balances
traffic for Smart Capacity™ solutions on Bytemobile’s Unison™ platform. The
high-performance T1000 enables operators to efficiently and cost-effectively manage
explosive growth in data traffic while delivering a high-quality experience to their
subscribers.
The T1000 Traffic Director can also provide advanced routing capabilities and load
balancing for the Bytemobile T3100 Adaptive Traffic Manager.
Note: This manual uses the generic term “T1000” to refer to all hardware models of
the T1000 Traffic Director, including the T1010, T1100, and T1200. Specific
model names are used only when necessary.
Objective
This manual describes how to install, configure, operate and maintain the T1000 Traffic
Director. Before completing the steps in this manual, read the safety instructions at the
beginning of this document.
Audience
This manual is intended for personnel who have been qualified to install and maintain
T1000 systems. Readers should be familiar with installing hardware and software in a
network operations center or in a mobile operator data center.
About This Guide

xvi T-Series Traffic Director Installation, Configuration and Administration Guide
About This Guide
Organization
This document is organized as follows:
T-Series Related Documents
The ByteMobile T-Series documentation set includes the following components:
•T3100 Architecture Overview
•T3100 Hardware Installation Guide
•T3100 Network Configuration Guide
•T3100 Network Configuration Worksheet
•T3100 Application Configuration Guide
•T3100 CLI Reference
•T3100 System Administration Guide
•T3100 Web GUI Reference
•T3100 Field Replacement Unit (FRU) QuickStart Guides
•T3100 Alarms and Troubleshooting Guide
•T3100 Safety and Notices Guide
Chapter Description
Safety Information All hardware-related safety information. Read this
section before installing the T1000 or performing
hardware maintenance.
Chapter 1, “Introduction” Overview of T1000 features and architecture.
Chapter 2, “Installing the T1000” Complete hardware installation procedures. Also
includes racking instructions and management
plane configuration.
Chapter 3, “Basic T1000/Unison
Load-Balancing Configuration” Describes how to configure Layer-2 and Layer-3 networking features of the T1000, and how to
configure the T1000 to load-balance Unison
platform traffic.
Chapter 4, “Dynamic Routing Protocol
Configuration for T 1000/Unison” Describes how to configure T1000 network features to support dynamic routing protocols
such as OSPF on Unison deployments.
Chapter 5, “Administration” Provides procedures for logging on to the T1000
CLI and GUI. Also describes how to integrate the
SNMP management features for monitoring
performance and managing alarms and events.
Appendix A, “T1000 Specifications” Hardware specifications for the T1000 platform.
Appendix B, “Replacement Parts” List of replacement parts for T1000. Includes
replacement instructions where appropriate.
Appendix C, “Legal Notices” Legal notices, copyrights, third-party software
disclosures, and other legal information.

T-Series Traffic Director Installation, Configuration and Administration Guide xvii
Unison Related Documents
•T2100 Installation, Configuration and Administration Guide
•T1000 Installation, Configuration and Administration Guide
•T-Series EMS Installation Guide and Reference
Consult the latest release notes for important information not contained in the
documentation set, such as resolved issues, known issues, and operating considerations.
Note: Manuals and release notes may be superseded by revised versions. ByteMobile
recommends visiting support.bytemobile.com for the latest releases of all
customer documents.
Unison Related Documents
The Bytemobile Unison documentation set includes the following components.
•Unison Architecture Overview
•Unison OSN Configuration Guide
•Unison Policy Manager Guide
•Unison KPI Tool Guide
•Unison Web Proxy Log File Specification
•Unison Media Proxy Log File Specification
•Unison OSN Disk Partitioning Spreadsheet
•Unison OSN Hardware Sizing Calculator
Citrix NetScaler Documents
The T1000 uses a common technology platform developed for the Citrix NetScaler
appliance. Certain configuration and administration features are shared by both the T1000
and by the NetScaler.
Citrix provides a documentation website
(http://support.citrix.com/proddocs/topic/netscaler/ns-gen-netscaler93-wrapper-con.html)
with a searchable database of documents that are also intended to support T1000
deployments. In particular, the following sections are applicable to T1000:
•Administration
•Reference Material (includes Command Reference Guide, Log Message Reference,
and SNMP OID Reference)
Revision History
Bytemobile periodically releases updated versions of manuals to address known issues with
the product, to correct errors, and to document features introduced in service pack releases.
The revision level and document release date are noted on the front cover.
This document has the following revision history (earlier revisions not shown):
•Rev. G: Seventh revision of this document. Has the following changes:

xviii T-Series Traffic Director Installation, Configuration and Administration Guide
About This Guide
–Updated rear panel view of the T1200. See “Model T1200 Hardware” on page 1-11.
–Updated rear panel views of the T1200 for ac and dc power connection in Chapter 2,
“Installing the T1000.”
–Updated the set lb vserver command in the procedure outlined in “Configuring
Minimum Servers and Backup Path” on page 3-24.
–Revised procedure for “Configuring Source NAT (SNAT)” on page 3-26.
–Added example to “Configuring Health Monitors” on page 3-22.
–Added additional information about configuring per-node weights to “Creating
Services” on page 3-19.
–Added additional procedure for binding the management IP address to a
VLAN/interface in “Setting Management IP Address” on page 3-8.
•Rev. H (DRAFT PENDING): Seventh revision of this document. Has the following
changes:
–Updated the heat and power output specifications of the T1200 in Appendix A,
“T1000 Specifications.”
–Updated the description of the number of power cords supplied with the AC power
T1200 in Chapter 2, “Installing the T1000.” The T1200 ships with 4 cords and not 2,
as previously indicated.
–Procedures previously available only to support personnel, such as “Upgrading the
T1000 Operating System” on page 5-4, have been added to the standard edition of
this document. The support-only edition of this document has been deprecated.
Document Conventions
This document uses the following conventions:
Convention Description
boldface Commands, keywords, user inputs, and menu choices.
italic Directory paths, file names, syntax items (parameters) that must
be replaced with specific values, emphasis on new terms, and
publication titles.
[ ] Keywords or arguments that appear within square brackets are
optional. Square brackets also indicate default responses to
system prompts.
{ x | x | x } A choice of keywords (represented by x) appears in braces
separated by vertical bars. You must select one.
^ or Ctrl Represent the key labeled Control. For example, when you read
^D or Ctrl-D, you should hold down the Control key while you
press the D key.
screen font Examples of information displayed on the screen.
boldface screen font Examples of information that you must enter.
< > Nonprinting characters, such as passwords, appear in angled
brackets.

T-Series Traffic Director Installation, Configuration and Administration Guide xix
Notices and Statements in this Document
Notices and Statements in this Document
The caution and danger statements in this document are also in the separate multilingual
Safety Guide. Each statement is numbered for reference to the corresponding statement in
the Safety Information document. The following notices and statements are used in this
document:
Note: These notices provide important tips, guidance, or advice.
Important: These notices provide information or advice that might help you avoid
inconvenient or problem situations.
Attention: These notices indicate possible damage to programs, devices, or data. An
attention notice is placed just before the instruction or situation in which
damage could occur.
Caution: These statements indicate situations that can be potentially hazardous to you. A
caution statement is placed just before the description of a potentially hazardous
procedure step or situation.
Danger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
Documentation Feedback
Bytemobile is committed to continuously improving the technical accuracy and usability of
its product documentation. If you have suggestions, comments, or corrections, please send
them to [email protected]. Your comments will help improve the next version of
the manual.
Technical Assistance
ByteMobile Technical Services for customers focuses on four areas: Professional Services,
Solutions Engineering, Customer Support, and Education Services. These services are
provided by an experienced team of data networking and support services professionals.
•Professional Services at pr[email protected] are provided for
network design, deployment, and documentation. Customized professional services
are also available in areas such as security monitoring and application verification.
•Solutions Engineering Services at solutions_engineeri[email protected] are
provided for custom feature development, third-party software integration and
certification, new hardware platform certification and user-interface customization.

xx T-Series Traffic Director Installation, Configuration and Administration Guide
About This Guide
•Customer Support Services at su[email protected] are available worldwide, on
a 24x7x365 basis for ByteMobile commercial customers with maintenance contracts
in place.
•Education Services, at [email protected], offer a curriculum of technical
training courses. Delivery methods include Classroom Training, Virtual Classroom
Training, and Web Based Training. Education Services can tailor classroom training
to meet individual customer and deployment requirements.
You can also find information about ByteMobile Technical Services at www.bytemobile.com.