Civintec CRYSTAL CT9 PRO User manual

CRYSTAL TOUCH TERMINAL
CT9 PRO INSTALLATION GUIDE
V2.0.1
Suitable models:
CT9-T-P, CT9-T-QP, CT9-T-P-M, CT9-T-QP-M,
CT9-T-P-UV, CT9-T-P-M-UV, CT9-T-QP-UV, CT9-T-QP-M-UV

The table below contains the history of changes made to the present
document.
Version Date Document Version History
V1.0 .0 2022-07-15 Original Version
*All rights reserved
*Subjects changed without notice
Information furnished by CIVINTEC Global Co., Limited. is believed to be
accurate and reliable. However, no responsibility is assumed by CIVINTEC
Global Co., Limited. for its use; or for any infringement of patents or other
rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent right of
CIVINTEC Global Co., Limited.
Introduction
This document is about CT9 Pro terminal installation instructions; please strictly
follow the instructions in the installation. In order to prevent screen bursting, do
not to touch the TP screen hard during installation.
V2.0 .1 2022-09-07 Optimize 4G cable

Technical Specification
CRYSTAL TOUCH
Display
Keypad
ISO-protocol
Contactless cards
Secure Access Module
Communication Interface
Operation System
Memory
Current consumption
CT9 Pro
3.5" touch screen
125KHz Prox, 125KHz EM, 13.56MHz Mifare® Classic, Ultralight®,
Ultralight®C, Mifare® Plus, DESFire® EV1/EV2, NFC tags (T2T, T4T)
Touch PIN Pad
125KHz, 13.56MHz ISO14443A/B, ISO18092 NFC
* Not all ISO14443 B cards have been implemented in the reader,
please contact Civintec for more details on current status.
ISO7816 (T=0, T=1) 1 SAM module, more on request
1x Wiegand Input (WG26, WG32, WG34, WG40, WG42, WG50,
WG56, WG58, WG64, WG128, Wg256), RS485 , BLE 4.0,
TCP/IP, 4G
LINUX
64MB LPDDR, 128MB Nand Flash
Average 800mA@ 12VDC
Protection Class
Operation Temperature
Operation Humidity
Certification
Installation
IP65 waterproof
-20 ~ +60°C
0-90% relative humidity non-condensing
CE approved
Terminal block connector, wall mount
Tamper switch 1* tamper alarm switch
Controllable buzzer, speaker with controllable volume
Indicator
I/O Port 1*I/O Port, 2*Wiegand(in)
2 inputs – Door contact, door exit
Barcode/QR scanner
· Area image 640 x 480 pixels, Filed of View 68°(H) x 51(V)
· Decode range: 20mm-150mm(QR 20MIL)
· Roll/Pitch/Yaw: 360°, ±55°, ±55°
· Multiple formats supported (1D & 2D Codes): QR Code,
Micro QR code, PDF417, Code 128, Code 39 and most
mainstream 1D and 2D barcodes.
9-30VDC, PoE(IEEE802.3af/at High Power interface,
optional – over JACK (connector)
Power Supply
Relay connections 1 relay output, Max switching voltage 30V, Max switching
current 2A

01 Terminal Introduction
3.5” Touch Screen Display
Card Reading Area
①
②
QR Code
③
1
2
3

SAM Slot
BLE & firmware upgrade interface
Software upgrade interface
Relay
PIN interfaces
Buzzer
Connector for 4G
Connector for QR Code
PoE (Optional)
①
②
③
⑤
⑥
⑨
④Tamper alarm
Speaker
RJ45 TCP/IP port
⑦
⑧
⑩
111111
1
3
24
5
6
9
8
7
11
10
02 Terminal introduction
6
12
121212
RJ45 TCP/IP port
The default IP address is"192.168.1.140".

03
①②
1
2
3
③
Installation plate Modules Introduction
CT9-T/H-QP Installation Plate CT9-M(E)-T Installation Plate
Tamper Alarm 4G Module (Optional)
QR Code Scanner (Optional) ④4G SIM slot
4

04 Package content
CT9 Pro terminal device
Installation plate
Screw
Screw expand tube
8 PIN Connector
2 PIN Connector
Fixing screw
RJ45 connector
No. Items Picture Volume
1
1
1
4
4
2
1
4
1
①
②
④
⑤
⑥
⑦
⑧
⑨
Waterproof silicone strip
③1
⑩
QR Code Scanner
(Optional)

05
165
18.1
6.8

06
Plug waterproof silicone strip into the groove at the upper end of CT9 Pro
installation plate.
Waterproof silicone strip

07
Ensure that the area behind the tamper switch bulb of the installation plate is
flat. Make sure that the Tamper Alarm button is completely against the wall for
correct tamper alarm functionality.
Screw
⑤

08
Unscrew the fixing screw from terminal and remove the installation plate from
terminal. Ensure that the installation plate is fixed in the correct direction, the
arrows pointing upwards.

09
According to the holes parameter of installation plate, punch holes in the wall
and install pipe expanding. Make sure to punch holes in strict accordance with
the parameters to avoid of plate deformation and failure installation. There’re
two choices to punch holes.
Screw expand tube X4
Wall Mount
⑥

10
There’s hole on installation plate, the hole is used for TCP/IP cable and connector
wires. Thread the cables through hole before fixing it on the wall.
TCP/IP
Connector wires

11
When installing directly to wall or door, use the installation holes as picture
describes. Make sure not to tighten the screws too hard as doing so will
deform and skew the installation plate. This may affect the tamper switch
functionality of the terminal.
Screw
⑤Screw
⑤
Screw
⑤Screw ⑤
Screw
⑤Screw
⑤
Screw
⑤
Screw
⑤
TYPE 1 of Installation Hole TYPE 2 of Installation Hole

12
Refer to general standard for IP wire connection, connect and fix RJ45
connector to TCP/IP cable which thread through upper hole.
RJ45 Connector
⑩
12
34
56
78
2
3
4
1
5
6
7
8
PIN
TX+
TX-
RX+
unused
unused
RX-
unused
unused

13
Refer to CT9 Pro terminal PIN definition, connect the cables with 8Pin or
2PIN connector and fasten screws. 2PIN connector is used for relay output.
2 PIN Connector
8 PIN Connector
⑧
⑦

14
Pin No. Pin Name Description
NO2
D0
D1
D2
GND
IN0
IN1
IN2
Direction Voltage
----
IN
IN
IN/OUT
Ground
IN
IN
IN
----
5V
5V
5V
0V
5V
5V
5V
REMARK
9
10
11
12
13
14
15
16
Pin No. Pin Name Description REMARK
NO1
IO2
IO1
IO0
TR-
TR+
GND
DC+
Relay 1 NO Normally Open
Tamper Alarm
Access Denied
Access Granted
RS485 Send/Receive Data-
RS485 Send/Receive Data+
Ground
9-30V DC Power
Direction Voltage
----
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
Ground
Power
Max.30V DC
5V
5V
5V
5V
5V
0V
9-30V
1
2
3
4
5
6
7
8
NO1
IO2
IO1
IO0
TR-
TR+
GND
DC+
9
10
11
12
13
14
15
16
NO2
D0
D1
D2
GND
IN0
IN1
IN2
1
2
3
4
5
6
7
8
NC1
COM1
COM2
NC2
17 18 19 20
Pin No. Pin Name Description Direction Voltage
NC1
COM1
COM2
NC2
Relay 1 NC Normally Closed
Relay 1 Common
No Connected
No Connected
----
----
----
----
Max.30V DC
Max.30V DC
----
----
REMARK
17
18
19
20
No Connected
Wiegand D0/DAT
Wiegand D1/CLK
Output Buzzer Control
Ground
Input Buzzer control
Input Entry Exit Button
Input Door Contact
*
*
*

15
1 2 3
CT9 Pro is with SAM secure access module for data encryption. In order to
install the SAM into the terminal open the SAM socket by unlocking and
opening the lid. Then place the SAM into the socket lock it into place by
closing the lid and sliding it into locked position.
SAM
SAM

15
1 2 3
CT9 Pro is with the option of 4G wireless communication. There’s SIM slot
on installation plate to insert SIM card. In order to install the SIM card into
terminal open the SIM socket by unlocking and opening the lid. Then place
SIM card into socket lock it into place by closing the lid and sliding it into
locked position.
SAM
SIM

16
At the first time when you get the machine, you need to remove the QR
code cover. Remove the two screws at the bottom of QR Code reader, and
then hold the QRcode left and right and pull it out according to the direction
of the picture. Be careful not to pull the QR code cover out too much, as its
cable is connected to the CT9 Pro machine.