Clare Controls CLIQ.host Assembly instructions

© Clare Controls, LLC. 1 / 4 Doc ID - 613 • REV 11
CLIQ.host Controller Installation Sheet
Last modified: 09/29/16
Description
The Clare Controls CLIQ.host controller provides all device
management services to AppModules, supports all Clare user
interface services, and acts as the gateway to the ClareCloud
for system updates. The controller comes complete with the
ClareOS and all AppModules preloaded. The controller also
comes equipped with a 908.4 MHz transceiver for controlling
your other devices, such as integrated lighting, thermostats,
sensors, and door locks.
Note: Models are subject to change without any prior notice.
WARNING: Any changes or modifications made to this product
not expressly authorized by the manufacturer could void the
user’s right to operate this device.
Unpacking the CLIQ.host
Remove all contents from the CLIQ.host packaging and ensure
you have the following items.
 1 × CLIQ.host device
 1 × power supply
 3 × terminal connectors
 1 × terminal connector jig
 2 × RJ12 to DB-9 connectors (null modem)
 6 × IR emitters
 1 × 908.4 MHz antenna and extender cable
 4 × rubber foot covers
Record the device’s UUID number (labeled on the bottom of
the device) on the line below, or scan the QR code (also on the
label) with a scanning app, and then email the number to your
system programmer. Your system programmer will need this
UUID information to configure the CLIQ.host device.
UUID: __________________________________
Do not use this UUID for more than one account.
WARNING: Do not apply power to the CLIQ.host until
installation is complete. Failure to do so may result in bodily
injury and/or damage to the equipment.
Installation
The CLIQ.host can be mounted in a structured enclosure, set
on a rack shelf, or placed in any room near your devices.
Note: The CLIQ.host contains a 908.4 MHz transceiver. To
prevent radio frequency (RF) interference from external
sources, we recommend that you place the CLIQ.host away
from devices that may cause interference and away from
conductive metals.
Mounting the CLIQ.host in a structured enclosure
When mounting the CLIQ.host in a structured enclosure, we
recommend using the Leviton Structured Media Enclosure or
the Suttle SOHO Access Enclosure panels fitted with the
ClareHome Structured Enclosure Extender (P/N CH-EXT-28
and CH-EXT-42) for added protection against heat build-up.
(Panels and extenders are sold separately.)
To mount the CLIQ.host in a structured enclosure:
1. Place the CLIQ.host inside the structured enclosure with
the rear of the device facing up, see Figure 1.
2. Using cable ties, secure the CLIQ.host to the enclosure.
Note: Be sure to leave at least 1U of spacing (1.75 in.
(4.45 cm)) above and below the CLIQ.host when mounting.
Figure 1: CLIQ.host mounted in a structured enclosure
(1) Mount CLIQ.host with cable ties
(1)

2 / 4 Doc ID - 613 • REV 11
Connecting devices to the CLIQ.host
After placing your CLIQ.host, make the connections to your
other devices. Figures 2 and 3 identify the LEDs and ports on
the front and rear of the CLIQ.host. Refer to the documentation
that came with each of your other devices for detailed
information about connecting those devices to the CLIQ.host.
To connect the CLIQ.host:
1. Connect your serial devices (optional) to either of the two
RS-232 ports using an RJ12 to RS-232 cable, or an RJ12
to DB9 null modem cable (included). See Figure 3, item 1.
For RJ12 pinouts, see Figure 6.
2. Connect your IR devices (optional) to the 12-pin terminal
connector (included), and then insert the connector into
the port labeled “IR Outputs.” See Figure 3, item 2.
If your IR device comes with a 3.5 mm connector, you will
need to cut and strip the wires before connecting it to the
terminal connector.
When connecting an IR emitter, attach the striped wire to
positive (+) and the black wire to negative (-).
3. Connect a CS-BR-1 Streams Audio Bridge (optional) to a
USB port on the CLIQ.host. See Figure 3, item 3.
Note: The USB connection allows the CS-BR-1 to encode
up to three simultaneous audio streams onto the CobraNet
network.
4. Connect your digital I/O devices (optional) to the 8-pin
terminal connector, and then insert the terminal connector
into the port labeled “I/O.” See Figure 3, item 4.
When connecting devices, wire it such that ports 1 and 2
share the same 12 VDC power and ground and ports 3
and 4 share the same power and ground.
5. Use an Ethernet cable (not included) to connect your
CobraNet switch to the port labeled “CobraNet.” See
Figure 3, item 5.
Note: The CobraNet port is preset with the static IP
address 172.30.100.1. All CobraNet devices used on the
same subnet must use an address from 172.30.100.2 to
172.30.100.254.
6. Use an Ethernet cable (not included) to connect to your
data network switch to the port labeled “Ethernet.” See
Figure 3, item 6.
Notes
 The Network port is preset to DHCP. If you are using
the Streaming Media server in your project, a fixed IP
address is not required and should be configured as
“localhost.”
 If you are using a device, such as an RTI remote that
requires the controller to have a fixed IP, you must set
the fixed IP using a MAC/DHCP reservation on the local
router.
7. Connect relay contacts (e.g., garage door contacts) to the
6-pin terminal connector, and then insert the terminal
connector into the port labeled “Relay.” See Figure 3,
item 7.
8. Attach the 908.4 MHz antenna or optional antenna
extender to the antenna port. See “Attaching the antenna”
below.
Figure 2: CLIQ.host front
(1) LED – It illuminates purple when booting and blue when running
normally
Figure 3: CLIQ.host rear connections
(1) RS-232 (2 ports)
(2) IR Outputs
(3) USB ports
(4) I/O
(5) CobraNet
(6) Ethernet
(7) Relay
(8) Antenna port
(9) Power – 12 VDC
Attaching the antenna
The 908.4 MHz antenna can be mounted to the CLIQ.host
controller, or further away using an extender cable (included)
to enhance radio performance. When mounting the CLIQ.host
inside a structured enclosure, always mount the antenna
outside the enclosure using the extender cable.
To attach the antenna directly to the CLIQ.host:
1. Remove the 908.4 MHz antenna from its packaging.
2. Screw antenna to the antenna port on the rear of the
CLIQ.host until the antenna is snug. Do not over-tighten
the antenna. See Figure 4.
RS232 IR Outputs USB I/O CobraNet Ethernet Relay
#1 #2
12vdc
Networks
#1 #2 1 2 3456
12vdc
Gnd
#3
#1
#2
12vdc
Gnd
#4
NC
NO
C
NC NO
C
(1) (2) (3) (4) (5) (6) (7) (8) (9)

Doc ID - 613 • REV 11 3 / 4
Figure 4: Attaching the antenna to the CLIQ.host
To attach the antenna using the extender cable:
1. Using a 17/64 in. drill bit, drill a hole in the sidewall of the
ClareHome Structured Enclosure Extender, near the
CLIQ.host.
2. On the extender cable, remove the locknut and washer
from the SMA Male connector. See Figure 5.
3. Insert the threaded end of the connector though the hole,
and then replace the washer and locknut, tightening the
locknut until the connector is secure and does not wobble
in the hole.
4. Screw the antenna to the connector until the antenna is
snug.
5. Attach the other end of the extender cable to the antenna
port on the rear of the CLIQ.host. See Figure 3, item 8.
Figure 5: Attaching the antenna with the extender cable
(1) SMA Male connector
(2) Washer
(3) Locknut
(1) (3)
(2)

4 / 4 Doc ID - 613 • REV 11
RS-232 port pinouts
If you are using your own RJ12 cable (rather than the one
supplied), ensure your RJ12 cable connector pinouts match
the pinouts on the RS-232 ports, as shown in Figure 6.
Figure 6: RS-232 ports with pinouts
Powering the CLIQ.host
Plugging in the power adapter automatically turns on the
CLIQ.host and starts the boot process.
To connect power to the CLIQ.host:
1. Plug one end of the power adapter into a power receptacle
on the back of the CLIQ.host labeled “12vdc.” See
Figure 3, item 9.
2. Check the LED on the front of the CLIQ.host. It illuminates
purple when booting and blue when running normally. See
Figure 2, item 1.
Time, date, and time zone
Your CLIQ.host controller automatically detects and sets its
time, date, and time zone when you connect it to your data
network. CLIQ.host uses NTP and synchronizes the date and
time at boot up and periodically throughout the day.
Configure, test, and deploy a project
Refer to the Fusion Configuration Tool Administrator Guide
(Doc ID 069) for instructions on creating, testing, and deploying
a project. When you deploy the project from Fusion, it will
deploy to the CLIQ.host.
Adding the rubber foot covers
To prevent the unit from sliding, use the four rubber foot covers
included with your CLIQ.host.
To add the rubber foot covers:
 Peel each foot cover from the paper backing and place
one on each foot on the bottom of the CLIQ.host.
Contact information
Clare Controls
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
Support: 941.404.1072
Fax: [phone]
www.clarecontrols.com
Specifications
I/O ports
RS-232 [1]
2
IR outputs
6 (2 pins per IR)
USB [2]
2
I/O
4 (8 pins)
CobraNet
1
Ethernet
1
Relay
6 pin, (2 normally open, 2 normally closed)
General
Processor
Freescale iMX6
Operating system
Linux
Memory
2 GB DRAM, 1 GB NAND Flash
Power
8.4 W (700 mA at 12 VDC)
Operating temperature
41 to 113°F (5 to 45°C)
Relative humidity
10 to 90%, non-condensing
Dimensions (W × H × D)
1.3 × 8 × 6 in.
3.3 × 20.32 × 15.24 cm
[1] CLIQ.host units support RS232 speeds of 300 baud and higher.
[2] CLIQ.host units marked Rev C or higher use both USB ports. Units
marked Rev B or lower, or with a numerical revision level, are use the
top USB port only. See the label on the bottom of the unit to
determine its revision level.
Regulatory information
Manufacturer
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
FCC compliance
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Warranty information
Clare Controls offers a three (3) year limited warranty on
original Clare Controls components, from the date of
shipment from Clare Controls. To view complete limited
warranty details, including limitations and exclusions,
www.clarecontrols.com/warranty.
Scan the code
to view product
warranty details.
RS232
#1 #2