Clare Controls CLIQ.mini User manual

DOC ID - 1284 • Rev 09 1 / 7
CLIQ.mini Quick Start Guide
Content
Introduction...1
Included and recommended tools...1
CLIQ.mini diagram...2
Installation options...3
LED Display...6
Troubleshooting...6
Warranty Information...7
Support...7
Last modified: 11/11/19
Introduction
Thank you for choosing Clare Controls. In today’s competitive market place, we
can appreciate that you have many choices for your home automation needs.
This document is intended as a quick-start guide, not a full product guide. For
more information, view the full CLIQ.mini Controller Installation and Setup Guide
(DOC ID 1263).
Included and recommended tools
Ensure all accessories are included. If not, contact your dealer.
Included with the CLIQ.mini.
•CLIQ.mini smart home control hub
•Ethernet cable
•Paper clip/Reset tool
•Power over ethernet (PoE) injector
•PoE power supply
•Mounting bracket and screws
•UUID/Mac identification labels
Recommended tools:
•#2 Phillips head screwdriver (used for mounting bracket installation)
•Needle node pliers (used to insert micro USB plug into CLIQ.mini)

DOC ID - 1284 • Rev 09 2 / 7
CLIQ.mini diagram
The following image is a diagram of the CLIQ.mini controller. Use this diagram
during installation and for reference.
Figure 1: CLIQ.mini diagram
(1) Recessed push button
(2) 2 USB ports
(3) Wire routing channel
(4) Wall mount slot
(5) Micro USB port
(6) Ethernet port

DOC ID - 1284 • Rev 09 3 / 7
Installation options
Select an installation option.
Installation Option 1: PoE (Power over Ethernet)
To connect to ClareHome you must have the Install Assist app, a CLIQ.mini
controller, and access to your home’s Wi-Fi.
Note: This method requires that the user has 2 Ethernet cables.
Figure 2: PoE wired connection
To setup your CLIQ.mini using PoE:
1. Connect the CLIQ.mini to the included PoE injector using an ethernet cable.
2. Connect the PoE injector to the router using a second Ethernet cable, and
then plug in the injector’s power supply.
Note: If the LED does not change to solid blue, see “LED Display” on page 6
or “Troubleshooting” on page 6.
3. Download Install Assist app for iOS or Android. You can now use apps to add
smart home devices. Refer to the Clare Controls Knowledge Base for
information on supported devices.
Note: A Fusion project must be created.

DOC ID - 1284 • Rev 09 4 / 7
Installation Option 2: Wi-Fi
To connect the CLIQ.mini using Wi-Fi, you will need access to the Install Assist
app, a CLIQ.mini controller, and the home’s Wi-Fi network.
Figure 3: Wi-Fi connection
To setup your mini using the power supply and ethernet:
1. Connect the CLIQ.mini to the included PoE injector using an ethernet cable.
2. Download the Install Assist app.
3. Open the Wi-Fi settings on your phone and connect to the CLIQ.mini’s
broadcasted network (ClareWifi-xxxx).
4. Open the Install Assist app and tap WiFi Config.
a. Enter the home’s Wi-Fi SSID and password, tap Next, and then follow the
on-screen instructions.
b. Wait for the LED on the CLIQ.mini to turn solid blue. The CLIQ.mini is now
connected to Wi-Fi.
c. Note: If the LED does not change to solid blue, see “LED Display” on
page 6 or “Troubleshooting” on page 6.

DOC ID - 1284 • Rev 09 5 / 7
5. Reconnect your mobile device to your home’s Wi-Fi, and then re-open the
Install Assist app.
6. You can now use the app to add smart home devices. Refer to the Clare
Controls Knowledge Base for information on supported devices.
Note: A Fusion project will also need to be created.
Wall mount
Once the CLIQ.mini is configured and connected to the home’s network, wall
mount the CLIQ.mini.
To wall mount the CLIQ.mini:
1. Attach the mounting bracket to the gang box.
2. Plug in the CLIQ.mini, and then slide it on to the mounting bracket.

DOC ID - 1284 • Rev 09 6 / 7
LED Display
The CLIQ.mini has an LED status indicator. Use the LED chart below to
determine the CLIQ.mini’s status.
Table 1: CLIQ.mini LED status
LED
LED behavior
Solid blue
Everything is working correctly.
Solid red
ClareOS is not operational. Shut down and power cycle the CLIQ.mini.
Blinking blue
The CLIQ.mini is not connected to the internet. Check your router status.
Blinking red
The CLIQ.mini is not connected to your home network. Shutdown and power
cycle the CLIQ.mini.
Note: Rapid blinding indicates Wi-Fi configuration is needed (CLIQ.mini is in AP
mode).
Blinking red and blue
Firmware update in progress, may take up to 10 minutes.
Not lit
There is no power connected to the CLIQ.mini. Check that the power supplies
are plugged in and wired correctly.
Troubleshooting
In certain states the CLIQ.mini must be reset or power cycled.
Note: When the CLIQ.mini reboots, it can take up to 25 seconds to successfully
restart in AP mode.
To shutdown the CLIQ.mini:
1. Slide the provided paper clip/reset tool into the recessed push button and
hold down for 5 seconds.

DOC ID - 1284 • Rev 09 7 / 7
To shutdown and power cycle the CLIQ.mini in AP mode:
1. Slide the provided paper clip/reset tool into the recessed push button and
hold down for 20 seconds.
Warranty Information
Clare Controls offers a three (3) year limited warranty on original Clare Controls
components, from the date of shipment form Clare Controls. To view complete
limited warranty details, including limitations and exclusions, see
www.clarecontrols.com/warranty.
Support
Dealer Support –contact Clare Technical Services at:
[email protected]
Homeowner Support –contact ClareCare
[email protected]