clare ClareOne User manual

© 04April21 Clare Controls, LLC. 1 / 3 DOC ID: 2021-04-2104-03
ClareOne High/Low Temperature Sensor
Last modified: 04/22/21
Part number: CLR-C1-HLT
Description
The ClareOne High/Low Temperature Sensor is a supervised,
wireless sensor that detects both a high temperature (100° F)
and low temperature (40° F). The sensor is mounted using
double-sided adhesive tape (included).
When activated, the sensor transmits an alert or status to the
ClareOne panel. This includes supervisory, tamper, and low
battery. The sensor is powered by (2) replaceable 3-VDC,
lithium coin-cell batteries.
Important safety instructions
Before you install this sensor, be sure to:
•Read, keep, and follow all instructions.
•When there is a low battery, replace with compatible
batteries.
Installation
Mounting the sensor on metal can affect the transmission
range and magnet gap performance. Please test the sensor
from the desired location before permanently mounting it.
Freeze Sensor Mounting
Using the supplied mounting tape find a location that would
most likely get cold first (alarm trips at 40F) for example:
•Under a kitchen sink
•In the bathroom
•Avoid area that may retain heat as furnace rooms or
near hot water pipes.
High Temp Sensor Mounting
High Temp sensors are designed to detect an increase in the
room temperature. Locate the sensor up as high as possible as
heat rises, the sensor detects at 100F.
For Additional Tamper Security
Punch out the tamper cover on
the bottom of the sensor and
using the small screw; secure it to
the mounting location. When the
sensor is removed “tampered” the
tab remains providing a tamper
condition.
CAUTION: Battery may explode if mistreated. Do not
recharge, disassemble, or dispose of in fire.

2 / 3 DOC ID: 2021-04-2104-03
Programming
The following instructions step for pairing the sensor to the
ClareOne panel.
1. Ensure sensor is not faulted.
2. Put the ClareOne panel into sensor pairing mode. For
detailed programming instructions, refer to the ClareOne
Wireless Security and Smart Home Panel User Manual
(DOC ID 1871).
3. Sensor Enrollment: The sensor can be programmed for
just freeze temperature detection, high temperature
detection, or both.
a. Freeze Sensor Enrollment:
i. Remove the sensor cover allowing the
tamper to trip, the panel will respond.
ii. Select Freeze as sensor type and add
sensor.
b. High Temp Sensor Enrollment:
i. Remove both of the sensor’s batteries.
ii. While holding down the tamper insert
the batteries, the panel will respond.
iii. Select Heat as sensor type and add
sensor.
4. Follow the ClareOne panel’s on-screen prompts to name
the sensor and make any desired changes to its default
settings.
Note: The sensor has 2 unique ID numbers allowing it to report
both freeze and heat alarms independently.
Note: If a low battery alarm occurs, replace the battery within 7
days.
Testing
Test the sensor before mounting it in the permanent location.
To test the sensor:
Set the ClareOne Panel into test mode.
Freeze Alarm: Alarm triggers when the temperature drops
below 40° F (4.44° C), restores when temperature rises above
45° F (7.22° C).
High Temp Alarm: Alarm triggers when the temperature rises
above 100° F (37.77° C), restores when temperature drops
below 95° F (35° C).
Specifications
Compatible panel
ClareOne (CLR-C1-PNL1)
Transmitter frequency
433 MHz
Encrypted
Yes
Transmitted indications
High Temp. Detection 100° F (37.77° C)
Low Temp. Detection 40° F (4.44° C)
Tamper
Low battery
Supervisory
60-70 minutes
Battery type
(2x) 3 VDC Lithium coin-cell battery, CR2032
Battery life
Up to 8 years
Operating environment
Temperature
Relative humidity
32 to 120°F (0 to 48.8°C)
95%
Storage temperature
-30 to 140° F (-34 to 60° C)
Dimensions
2.25 × 1.0 × 0.5 in.
(57.15 × 25.4 × 12.7 mm)
Certification
s FCC: 15.109 Class B 15.231, Industry
Canada: ICES-003, RSS-210
Regulatory Information
Manufacturer
Clare Controls, Llc.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
FCC compliance
FCC / IC Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced
radio/TV technician for help.

3 / 3 DOC ID: 2021-04-2104-03
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation
of the device.
Cet appareil est conforme avec Industrie Canada
exempts de licence standard RSS (s). Son
fonctionnement est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas provoquer
d'interférences et (2) cet appareil doit accepter
toute interférence, y compris celles pouvant
causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human
exposure to radio frequency fields, the radiating
element shall be installed such that a minimum
separation distance of 20 cm is maintained from
the general population.
FCC: 2ABBZ-RF-HLT-433
IC: 11817A-RFHLT433
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation. Changes or
modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
This Class B digital apparatus complies with
Canadian ICES-3B.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
MANUFACTURER HEREBY DISCLAIMS ALL
WARRANTIES AND REPRESENTATIONS,
WHETHER EXPRESS, IMPLIED, STATUTORY
OR OTHERWISE INCLUDING (BUT NOT
LIMITED TO) ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO
THESE PRODUCTS AND ANY RELATED
SOFTWARE. MANUFACTURER FURTHER
DISCLAIMS ANY OTHER IMPLIED WARRANTY
UNDER THE UNIFORM COMPUTER
INFORMATION TRANSACTIONS ACT OR
SIMILAR LAW AS ENACTED BY ANY STATE.
(USA only) SOME STATES DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES,
SO THE ABOVE EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS AND YOU MAY
ALSO HAVE OTHER LEGAL RIGHTS THAT
VARY FROM STATE TO STATE.
MANUFACTURER MAKES NO
REPRESENTATION, WARRANTY, COVENANT
OR PROMISE THAT ITS ALARM PRODUCTS
AND/OR RELATED SOFTWARE (I) WILL NOT
BE HACKED, COMPROMISED AND/OR
CIRCUMVENTED; (II) WILL PREVENT, OR
PROVIDE ADEQUATE WARNING OR
PROTECTION FROM, BREAK-INS,
BURGLARY, ROBBERY, FIRE; OR (III) WILL
WORK PROPERLY IN ALL
Environmental
class
EU compliance
EN 54
EN 54-00:0000
1999/5/EC (R&TTE directive): Hereby, Clare
Controls declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to
your supplier or to a designated collection point.
For more information see: www.recyclethis.info.
Warranty information
Clare Controls offers a two (2) year limited warranty on original
Clare Controls components, from the date of shipment from
Clare Controls.
Contact Information
Clare Controls, LLC.
7519 Pennsylvania Ave, Suite 104
Sarasota, FL 34243
General: 941.328.3991
Fax: [phone]
www.clarecontrols.com
Integrator/Dealer Support: 941.404.1072
[e-mail]