Clarion NAX963HD User manual

Service information
Control no.: 06SI010-R
CLARION Europa GmbH, Hessenring 19-21, 64546 Morfelden-Walldorf, ++49 6105 / 977-0 Fx / 977-100
06SI010-R10.11.06 Page 1of 2
HDD access error message
1) Model outline:
NAX963HD
2) Description:
The navigation shows “ACCESS ERROR” on the display, as shown below.
3) Solution
Reset the NAX963HD navigation unit to the factory setting by following
the below mentioned procedure:
1)Press “Menu” on the main unit.
2)Select “Settings” on the touch screen
3)Press “Next”
4)Select “ Service option”
5)Select “Reset to Factory Settings”
6)Press “OK”, when asked for.

Service information
Control no.: 06SI010-R
CLARION Europa GmbH, Hessenring 19-21, 64546 Morfelden-Walldorf, ++49 6105 / 977-0 Fx / 977-100
06SI010-R10.11.06 Page 2of 2
Attention:
All user data on the hard drive will be lost and the factory settings will be
installed again.
After the installation of the factory settings,the NAX963HD will start up
automatically.
It may happen that the NAX963HD show this error message again. In this
case, switch off the unit and restart it manually. Now the error message
shall not be shown again.
In case the error message will not disappear,a hardware defect on the
unit is detected and the unit has to be exchanged via CEF.

NAX963HD
-1-
Service Manual
Published by Service Dept.
Printed in Japan
ClarionCo.,Ltd.
50Kamitoda,Toda-shi,Saitama 335-8511 Japan
ServiceDept.: 5-66Azuma,Kitamoto-shi, Saitama 364-0007 Japan
Tel:[phone] FAX:[phone]
298-6375-00 AUG.2006
Model
HDD Navigation System
(QY-5000E-A)
SPECIFICATIONS
Navigation System
GPS receiving frequency:
1575.42 MHz, C/A Code
Sensibility: -130 dBm or better
Number of GPS channels:
15 channels
Voice synthesis: ADPCM,
Sampling frequency;11.025 kHz
Power supply voltage: +14V
Ground: Negative
Current consumption: less than 3.0A
Dimensions(mm): 205(W)x29.5(H)x169(D)
GPS aerial
Mode: Microstrip flat aerial
Dimensions(mm): 30.4(W)x11.7(H)x35.5(D)
Impedance: 50 ohm
NOTES
About the hard disk drive
* Data saved to the hard disk drive may get lost in case of
a breakdown, malfunction, or other trouble of this unit.
Importing Data via USB Port
* Data may be broken when using USB memories sticks
in the following situation: When disconnecting the USB
memory stick or turning the power off during writing or
reading data. When affected by static electricity or elec-
tric noises.
* Music files (MP3, WMA, etc.) stored in the USB memory
stick cannot be played back.
("Data" : Including the stored locations and their data,
route data, data stored in the Favourite & Frequent List,
setting data set from the Setting menu, and data imported
from the USB memory stick (Wallpapers, Safety Cam-
era locations, etc.)
* The special equipment is necessary to replace IC103.
* We cannot supply PWB with component parts in
principle. When a circuit on PWB has failure, please
repair it by component parts base.
Parts which are not mentioned in service manual are
not supplied.
* Specifications and design are subject to change without
notice for further improvement.
This product is a lead free model.
Lead free solder is used in PWB stamped LF mark.
Please keep the following conditions when you repair.
1. Use lead free solder.
* Koki's lead free solder S3X-55M 0.6mm
(CLARION Parts No.642-0231-01)
* Koki's lead free solder S3X-55M 1.0mm
(CLARION Parts No.642-0231-02)
2. Use a nitrogen solder system.
3. Do not use "General solder" and "Lead free solder"
together.

NAX963HD -2-
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in charge
of repair or inspection can avoid suffering any risk or
injury.
1. Use specified parts.
The system uses parts with special safety features against fire
and voltage. Use only parts with equivalent characteristics
when replacing them.
The use of unspecified parts shall be regarded as remodeling
for which we shall not be liable. The onus of product liability
(PL) shall not be our responsibility in cases where an accident
or failure is as a result of unspecified parts being used.
2. Place the parts and wiring back in their original positions after
replacement or re-wiring.
For proper circuit construction, use of insulation tubes, bond-
ing, gaps to PWB, etc, is involved. The wiring connection and
routing to the PWB are specially planned using clamps to keep
away from heated and high voltage parts. Ensure that they are
placed back in their original positions after repair or inspec-
tion.
If extended damage is caused due to negligence during re-
pair, the legal responsibility shall be with the repairing com-
pany.
3. Check for safety after repair.
Check that the screws, parts and wires are put back securely
in their original position after repair. Ensure for safety reasons
there is no possibility of secondary ploblems around the re-
paired spots.
If extended damage is caused due to negligence of repair, the
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts
for the automobile.
Disconnect the battery terminal after turning the ignition key
off. If wrong wiring connections are made with the battery con-
nected, a short circuit and/or fire may occur. If extensive dam-
age is caused due to negligence of repair, the legal responsi-
bility shall be with the repairing company.
5. Cautions in soldering
Please do not spread liquid flux in soldering.
Please do not wash the soldering point after soldering.
6. Cautions in soldering for chip capacitors
Please solder the chip capacitors after pre-heating for replace-
ment because they are very weak to heat.
Please do not heat the chip capacitors with a soldering iron
directly.
7. Cautions in handling for chip parts.
Do not reuse removed chips even when no abnormality is ob-
served in their appearance. Always replace them with new
ones. (The chip parts include resistors, capacitors, diodes, tran-
sistors, etc).
Please make an operation test after replacement.
8. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron
tip temperature is around 270 . Take care not to apply the
iron tip repeatedly(more than three times)to the same patterns.
Also take care not to apply the tip with force.
9. Turn the unit OFF during disassembly and parts replacement.
Recheck all work before you apply power to the unit.
COMPONENTS
QY-5000E-A
1. Main unit ----------- 1
2. RDS-TMC amtenna ZCA-412-310 1
3. Microphone for voice control 081-0034-00 1
4. GPS antenna 096-0147-00 1
5. Power supply lead 854-6451-50 1
(5A Fuse 120-0050-00 1)
6. RGB cable(2.5m) 855-2433-01 1
7. CeNET cable(2.5m) 855-3421-90 1
8. Accessory bag ----------- 1
8-1. Electro-tap(for speed sensor) 060-0018-00 2
8-2. Electro-tap 060-0305-00 1
8-3. Mounting bracket 300-7362-03 2
8-4. Cord holder 321-1026-01 10
8-5. Canoe clip 335-2515-00 4
8-6. Waterproof rubber 345-7473-00 1
8-7. Double-sided tape for fastening the antenna
347-6369-00 1
8-8. Inatallation bolt(M4x6) 714-4006-8B 4
1 2 3
4 5 6
7
8
8-1 8-2 8-3
8-4 8-5 8-6
8-7 8-8

NAX963HD
-3-
The provider of RDS-TMC is not
automatically selected.
Error Message Cause Remedy
USB memory
device ACCESS ERROR
The USB memory device cannot be
accessed.
The USB memory is not
connected correctly. Connect the USB memory again.
The USB memory is not recognised. Connect another USB memory.
Hard Disk Drive TEMP ERROR
Cannot operate correctly due to high
temperature. Please wait until
temperature becomes normal again.
The HDD cannot be accessed
because the temperature in the
vehicle is extremely high
Please wait until the temperature
becomes appropriate.
TEMP ERROR
Cannot operate correctly due to low
temperature. Please wait until
temperature becomes normal again.
The HDD cannot be accessed
because the temperature in the
vehicle is extremely low
Please wait until the temperature
becomes appropriate.
ACCESS ERROR
Malfunction occured in the HDD.
Please consult your nearest dealer.
The HDD cannot be accessed.
The sectors or clusters of the
HDD may be damaged.
Problem Check point Remedy
Connection of power cable
Connection of RGB cable
Output of RGB signal
Output level of RGB signal
Dot clock
Connect power cable properly.
Confirm the frequency of the dot clock. (TP534)
Connect RGB cable properly.
Connect microphone properly.
Connect GPS antenna properly.
Connect antenna properly.
Change the installation position.
Separate from the antenna of the vehicle.
(especially, glass antenna)
Connect internal wiring (ANT700,ANT701) properly.
Connect speed pulse cable properly.
Connection of CeNET cable Connect CeNET cable properly.
Power supply circuit Confirm the output voltage of the power properly.
TP1000 HDD_5V
TP1001 D_5V
TP1003 D_3.3V
TP1008 DDR_2.5V
TP1004 VCC 1.22V
Confirm the output of RGB signal.
TP1115 R
TP1116 G
TP1114 R
Confirm the output level of RGB signal.
TP1115 R
TP1116 G
TP1114 R
Confirm collector voltage of Q803.
0V : MUTE-ON
3.3V : MUTE-OFF
Confirm IC800.
pin9(SDTO):Data output according to voice input.
pin10(LRCK):11.025KHz
pin11(MCLK):8.46MHz
pin12(SCLK):705KHz
Confirm collector voltage of Q801.
0V : MUTE-ON
3.3V : MUTE-OFF
Confirm audio wave form of TP801(AD_IN).
Confirm an output signal of TP1105(ECC).
Confirm the power supply voltage.
TP2101 R_TU8V
TP2113 TUNER3.2V
Confirm the oscillation of X2102(10MHz)
and output power of TP2209 (BU5V).
Measure pin1(VOUT) of Gyro(IC702) with the
tester. Confirm the voltage.
At geostationary: about 2.5V
When sets are rotatedand: voltage moves.
Confirm IC801.
pin1(LRCK):11.025KHz
pin18(MCLK):8.46MHz
pin19(BCLK):705KHz
pin20(DIN):Data input
Confirm an analog aoudio signal output of pin12 of
IC801.
HDD Insert HDD, and put protecting.
Adjust the volume properly.
The color of the screen is defective.
Guide voice doesn't sound. Volume level of guide voice
Clock and data input of DAC(IC801)
Output of DAC(IC801)
MUTE setting
Connection of microphone
Connection of speed pulse
Connection of GPS antenna
Connection of antenna
Setting position of window antenna
Noise source in car (PC,DC/AC converter)
Connection of internal wiring
Wave form of speed pulse
Input signal of ADC(IC800)
Clock and data output of ADC(IC800)
Gyro sensor
Stop the equipment that generates the noise.
Tuner Pack
RDS/TMC microcomputer
Selection of "TMC Provider screen". Select "Automatic".
Power indicator doesn't light.
(The power supply doesn't enter).
Screen is not displayed.
Map is not displayed.
The car position doesn't move.
GPS reception is defective.
RDS-TMC reception is defective.
Voice recognition is defective.
TROUBLESHOOTING
ERROR MESSAGES

NAX963HD -4-
IC403
SRAM
512KB
IC200,IC201,
IC202,IC203
DDR-SDRAM
128MB(256Mbx4)
IC400
DISK ON CHIP
64MB
IC800
ADC
SENSOR
I/F
J1102 J1103 P701
(Connector for production)
IC700
ADC
BL700
GPS
Tuner Pack
J701
IC702
GYRO
SENSOR
J800
MIC IC803
FILTER
R/G/B
IC401
BUS BUFER
16 64
16
16
IC501
FPGA
CSYNC
IC103
CPU
IC602
BUS
BUFFER
2.5inch 30GB
HARD DISK DRIVE
16
SCIF5
SCIF0
USB Host
ATAPI
RGB
DDR I/FEX-BUS
SSI0 SSI1
CS0
EX_CS0
8
H-UDI
JTAG
IC801
DAC
Control
IR IN
(96MHz)
(32MHz)
IC1102,IC1103
RGB
BUFFER
GUIDE
SIG.
TTS/WAVE (GUIDE VOICE)
VOICE RECOGNITION
16 X101
OSC
48MHz
X100
OSC
14.31818MHz
EXTALDOTCLKIN USBCLKAUDIO_CLK
CLKOUT
(CKIO)
32MHz - FPGA - DOC - DEBUG CN
CLKIN(CKIO)
From SH7770
32MHz
EX_CS2
IC909
MICOM
IC912
IE-BUS
DRIVER
X900
XTAL
10MHz
IC802,IC804
BUFFER
SCIF2 UART
J500(Unmounting)
DEBUG CONNECTOR for Development
X102
OSC
8.46MHz
IC2105
MICOM
RDS-
DEMODURATOR
IC2102
BL2101
RDS/TMC Tuner
C2B
X2102
XTAL
10MHz
X2101
XTAL
4.33MHz
UART
UART
UART
SCIF7
16 EX_CS4
EX_CS7 EX_CS1
From SH7770
32MHz
From SH7770
32MHz
IC908
EEPROM
1Kbit
Note
RDS-TMC PWB Block
Main PWB Block J1100 J1101
Control signal Other signal
Video signal Audio signal
㪧㪸㫉㪸㫃㫃㪼㫃㩷BUS 㪪㪼㫉㫀㪸㫃㩷㪺㫆㫄㫄㫌㫅㫀㪺㪸㫋㫀㫆㫅
CSYNC
TP
IC505
PLL
(9.1101MHz㪄10.085663MHz)
PDOUT4FSCEXCLK
SCIF4
ANT AMP
RDS-TMC
ANT
GPS
ANT
POWER
SUPPLY
BLOCK
Q1100,Q1101,IC1100,IC1101
SENSOR I/F:
PKB,BACK,ECC
B/U
12V
IC502
BUFFER
MIC CON.
CeNET
CONN. CeNET
CONN.
To RDS
CONNECT.
HDD
CONNECT. USB CON.
BU12V, PKB/BACK/ECC
CONNECTOR RGB
CONNECTOR SERIAL
CONNECTOR
BLOCK DIAGRAM
Video/Audio/Control block

NAX963HD
-5-
Debug Connector
Reset Block
IC103
CPU
SH Navi1
/RESET /RESET_OUT
SRAM
FPGA
HDD
ADC (AK5357)
IC904
Detector
R3112N211A
IC900
Detector
R3112N211A
IC901
Detector
R3112N211A
HDD_5V DET.
10K
3.9K 3.3K
D_5V
DET VOLT(high):4.81V DET VOLT(Low):4.58V
0.033uF
100
DDR_2.5V DET.
D_3.3V DET.
DDR
2.5V
0.033uF
100
Disk On Chip
/BUSY
/RSTIN
D_3.3V
D_3.3V
D_3.3V
D_3.3V D_3.3V
Delay:150ms
1000pF1000pF
/PERI _RESET
47K
D_3.3V
D_5V
1000pF
100
D_3.3V
IC909
SUB
Micon
/RESET
/CPU_RST
100
1000pF
100
10K
/IDE_RST 82
100
/RESET_OUT
/RESET_IN
D_3.3V
100
16K 39K
D_3.3V
0.033uF
100
/NAVI_RESET
100
1000pF
47K
D_3.3V
100
1000pF
SN74ALVC08 (2/4)
SN74ALVC08 (3/4)
SN74ALVC08 (4/4)
SN74ALVC08
47K
10K
10K
/BASE_RESET
/SH_RESET_OUT
/DOC_RST IN
/NAVI_RESET
/DOC_BUSY
1000pF
1000pF
Delay:150ms
Delay:150ms
DET VOLT(high):2.20V DET VOLT(Low):2.10V
DET VOLT(high):3.11V DET VOLT(Low):2.96V
Reset block

NAX963HD -6-
Power Detect Block
Micro Controller
B/U 12V
IC903 Detector R3111N271A
ACC_DET
BU_9V_DET
ACC DET.
/SYS-ACC
B/U DET.
/P_OFF
NAVI_PON
/BU-DET
Power supply ON/OFF SW on Mian PWB
Power-OFF signal from SH
B/U-VOLT watch signal to SH
SN74LVC2G32
TC7S32FU
SN74LVC1G08
47K
4.7K
56K
24.7K
47K10K
10K
0.1u
Q900
2SA1586
47K
100
100
B/U_3.3V
B/U_3.3V
B/U_3.3V B/U_3.3V
D_3.3V
Power supply (Power circuit block)
B/U DET. VOLT(high):9.26V DET. VOLT(Low):8.82V
1SS355
1000pF
100
S-TV
Ce-net Connector
ACC
IC103 SH-Navi1
NMI
IC909 SUB Micro Controller
/SHUTDOWN 100
47K
Shout down signal by compulsion from microcomputer
1000pF
/P_OFF_B
/NMI_MONI
/SHUTDOWN
/BU_DET
1000pF
NMI
100
D_3.3V
SN74ALVC08(1/4)
GPIO2A20/TX9
GPIO2A22/CSK9
/NAVI_MONI
10K
D_3.3V
10K
D_3.3V
Power detect block

NAX963HD
-7-
Power circuit block
Power Circuit Block
CAR BATTERY IC1002
B/U_5V TDA3664
Max. permissible current:100mA
Max. permissible current:150mA
Max. permissible current:3000mA [D_3.3V] , [D_5V] ON/OFF SW by VCC_1.22V
* Setting of timing for core power of [Navi core-FPGA] and I/O power. * [D_5V] ON/OFF SW for protection of [Navi core] and [FPGA].
IC1000 B/U_3.3V LM2954
IC1005 VCC_1.22V DDR_2.5V TPS5120
IC1003 HDD_5V LM3485
IC1001 A_9V BA09CC0WFP
10k
3.9k
10k
2SD1306
2SA2096
4700uF x 2
100(1/4W) x6
RDS PWB
NAVI_P_ON
Detector 2.20V Release 2.10V Det.
Detector 4.81V Release 4.58V Det. Detector 3.11V Release 2.96V Det.
1.22V
2.5V
IC1006 D_3.3V BD00KA5WFP
Coin Battery
DC/DC (200kHz)
DC/DC (100kHz)
Linear Linear
Linear
IC1004 A_5V BA05CC0WFP
Vref
Logic
SRAM
GPS Receiver
SHNavi1 FPGA SHNavi1 DDR
DDR HDD
SHNavi1 FPGA
Audio DAC/ADC
USB
Sub Micon
GPS Receiver Gyro
Analog circuit
Audio DAC/ADC
Mic
RGB Encoder
Logic
Max. permissible current:3000mA
Max. permissible current:500mA
Max. permissible current:1000mA
Max. permissible current:1000mA
Max. permissible current:3000mA
10k
470
10k
2SC4081
2SB1188
220
Power supply circuit ON/OFF SW on Navi PWB
RDS/TMC Tuner
8.5uA typ.
120uA max.
85mA typ. 95mA max.
GPS Receiver
Tuner Micon
RDS De- Modulator
105mA max.
500mA max. 40mA max.
20mA max. (DataSheet)
13.5mA max. (DataSheet)
30mA max. (DataSheet)
30mA max. (DataSheet)
2.2u
15k (F) 15k (F)
Linear
Linear

NAX963HD -8-
5A Fuse
(120-0050-00) Main power supply (Yellow)
Speed sensor (Pink)
Reverse gear signal (Purple/white)
Ground (Black)
NAX963HD
Front view (inside of Escutcheon)
Rear view
VRX868RVD
GPS antenna
(096-0147-00)
Microphone for voice control
(081-0034-00)
RDS-TMC antenna
(ZCP-412-310)
Power supply lead
(854-6451-50)
RGB cable
(855-2433-01)
CeNET cable
(855-3421-90)
Handbrake (Green)
Connectors
Example of connecting to the VRX868RVD
HDD
1
RDS-TMC antenna recept.
3
12
3 4
Mic.jack
6
GPS antenna recept.
8
578
6
Power supply connector
2468
1357
4
1
2
3
4
5
6
7
8
N.C.
PARKING BRAKE
N.C.
SPEED SENSOR
GROUND
REVERSE SIG.
BATTERY (+)
N.C.
RGB connector
3
7
5
68
2
1
4
7
1
2
3
4
5
6
7
8
B
C-SYNC
R
N.C.
N.C.
G
N.C.
N.C.
1234
USB connector
2
1
2
3
4
5V
D-
D+
GND
CeNET connector
11 12
78910
3456
1132
5
1
2
3
4
5
6
7
8
GND
SYS B/U
L-CH(+)
EXT(+)
EXT(-)
GUS(+)
R-CH(+)
R-CH(-)
9
10
11
12
13
SYS ACC
BUS(-)
L-CH(-)
ILLUMI.
N.C.
WIRE CONNECTION

NAX963HD
-9-
EXPLANATION OF IC
051-3304-90 LP2954IMX Voltage Regulator
Terminal Description
pin 1: Power out : O : DC power voltage output.
pin 2: Sense :IN: The voltage regulator may be pin-strapped
for 5V operation using its internal resistive
divider by tying the Output and Sense pins
together.
pin 3: Shut Down_ :IN: A logic-level signal will shut off the regu-
lator output when aLOW(<1.2V) is
applied to the Shutdown input.
pin 4: Ground : - : Ground.
pin 5: Error_ : O : Error flag output.
pin 6: 5V-TAP :IN: The voltage regulator may be pin-strapped
for 5V operation using its internal resistive
divider by tying the Feedback pin and 5V-
Tap pins together.
pin 7: Feed back :IN: Feed back voltage input.
pin 8: INPUT :IN: Positive power supply input.
051-3356-90 BD00KA5WFP
Positive Voltage Regurator(Adjustable)
051-3377-90 LM3485MM Hysteretic PFET Buck Controller
General Description
The LM3485 is a high efficiency PFET switching regulator controller
that can be used to quickly and easily develop a small, low cost,
switching buck regulator for a wide range of applications.
The hysteretic control architecture provides for simple design without
any control loop stability concerns using a wide variety of external
components.
The PFET architecture also allows for low component count as well
as ultra-low dropout, 100% duty cycle operation.
Another benefit is high efficiency operation at light loads without an
increase in output ripple.
Current limit protection is provided by measuring the voltage across
the PFET's RDS(ON), thus eliminating the need for a sense resistor.
The cycle-by-cycle current limit can be adjusted with a single resis-
tor, ensuring safe operation over a range of output currents.
Terminal Description
pin 1: I SENSE : The current sense input pin. This pin should
be connected to Drain node of the external
PFET.
pin 2: GND : Signal ground.
8
7
6
5
INPUT
FEEDBACK
5V TAP
ERROR_
1
2
3
4
OUTPUT
SENSE
SHUTDOWN_
GROUND
5.
4.
3.
2.
1.
Adjust
Output
N.C.
Vcc
On/Off (H=ON)
FinGround
R1
R2
Vc
Vo
I SENSE
GND
NC
FB
1
2
3
4
V IN
P GATE
PWR GND
ADJ
8
7
6
5
pin 3: NC : No connection.
pin 4:FB :The feedback input. Connect the FB to a
resistor voltage divider between the output
and GND for an adjustable output voltage.
pin 5: ADJ :Current limit threshold adjustment. It con-
nects to an internal 5.5uA current source. A
resistor is connected between this pin and
the input Power Supply. The voltage across
this resistor is compared with the VDS of the
external PFET to determine if an over-current
condition has occurred.
pin 6: PWR GND : Power ground.
pin 7: P GATE : Gate Drive output for the external PFET.
PGATE swings between VIN and VIN-5V.
pin 8: V IN : Power supply input pin.
051-3380-90 TPS5120DBTRG4
Dual output, Two-phase synchronous buck DC/DC controller
Terminal Description
pin 1: INV 1 :IN: Inverting input of CH 1 error amplifier, skip
comparator, and OVP1/UVP1 comparator.
pin 2: FB 1 : O : Feedback output of CH 1 error amplifier.
pin 3: SOFT START 1 :I/O:Soft start pin for CH1.
pin 4: PWM/SKIP :IN: PWM/SKIP mode select pin.
pin 5: CT :I/O:External capacitor from CT to GND for
adjusting the triangle oscillator.
pin 6: 5V STBY :IN: 5V linear regulator output.
pin 7: GND : - : Control ground.
pin 8: REF : O : 0.85V reference voltage output.
pin 9: STBY 1 :IN: Standby control for CH1.
pin 10: STBY 2 :IN: Standby control for CH2.
pin 11: FLT :I/O:Fault latch timer pin.
pin 12: POWER GOOD : O : Power good open-drain output.
pin 13: SOFT START 2 :I/O:Soft start pin for CH2.
pin 14: FB 2 : O : Feedback output of CH 2 error amplifier.
pin 15: INV 2 :IN: Inverting input of CH 2 error amplifier, skip
comparator, and OVP2/UVP2 comparator.
pin 16: LH 2 :I/O:Bootstrap capacitor connection for CH2
high-side gate drive.
pin 17: OUT 2u : O : Gate drive output for CH2 high-side
switching FETs.
pin 18: LL 2 :I/O:Bootstrap this pin for CH2 high-side gate
driving return and output current protec-
tion. Connect this pin to the junction of
the high-side FETs for a floating drive
configuration.
pin 19: OUT 2d : O : Gate drive output for CH2 low side gate
drive.
pin 20: OUT GND 2 : - : Ground for CH1 FET drivers.
pin 21: REG 5V IN :IN:External 5V input.
pin 22: Vref 5 : O : 5V internal regulator output.
pin 23: TRIP 2 :IN: External resistor connection for CH2 out-
put current control.
pin 24: VCC : - : Supply voltage input.
pin 25: TRIP 1 :IN: External resistor connection for CH1 out-
put current control.
pin 26: OUT GND 1 : - : Ground for CH1 FET drivers.
pin 27: OUT 1d : O : Gate drive output for CH1 low side gate
drive.
pin 28: LL 1 :I/O:Bootstrap this pin for CH1 high-side gate
driving return and output current protec-
tion. Connect this pin to the junction of
the high-side FETs for a floating drive
configuration.
pin 29: OUT 1u : O : Gate drive output for CH1 high-side
switching FETs.
pin 30: LH 1 :I/O:Bootstrap capacitor connection for CH1
high-side gate drive.

NAX963HD -10-
051-5344-90 NJM2267V-TE2 Dual Video Driver
051-5408-38 R3112N211A-TR-FA Voltage Drop Detector 2.1V
Terminal description
pin 1: OUTPUT : N channel open drain output.
This terminal will output L, if the voltage of
VDD becomes lower than the setting voltage.
pin 2: VDD : Positive supply voltage.
pin 3: GND : Ground.
pin 4: N.C. : Not in use.
pin 5: C.T. : Delay time capacitor connection.
051-5418-28 R3111N271A-TR-FA
Precision Voltage Down Detector 2.7V
Terminal description
pin 1: OUTPUT : N channel open drain output.
This terminal will output L, if the voltage of
VDD becomes lower than the setting voltage.
pin 2: VDD : Positive supply voltage, negative logic input.
pin 3: GND : Ground.
pin 4: NC : Not in use.
pin 5: NC : Not in use.
051-6650-90 NB2305AT1HDR2G 3.3V Zero Delay Clock Buffer
Terminal Description
pin 1: REF : Input reference frequency, 5 V tolerant input.
pin 2: CLK 2 : Buffered clock output.
pin 3: CLK 1 : Buffered clock output.
pin 4: GND : Ground.
pin 5: CLK 3 : Buffered clock output.
pin 6: VDD : 3.3 V supply.
pin 7: CLK 4 : Buffered clock output.
pin 8: CLK OUT : Buffered clock output, internal feedback on
this pin.
6dB
75ohm Driver
750
ohm
2.0k
ohm
2.2k ohm
14
3
6dB
75ohm Driver
750
ohm
2.0k
ohm
2.2k ohm
85
6
7 2
GNDVCC
1
2
3
5
4
C.T.
N.C.
OUTPUT
VDD
GND
1
2
3
5
4
N.C.
N.C.
OUTPUT
VDD
GND
CLK OUT
CLK 4
VDD
CLK 3
8
7
6
5
REF
CLK 2
CLK 1
GND
1
2
3
4
PLL
Bit CK IN 19
LR CK IN 1
DATA IN 20
Vref P 5
Vref N 6
V MID 8
Audio
Interface Digital Filters
DAC Vout L P12
Vout L N11
DAC Vout R P9
Vout R N10
A VDD 4
A GND 7
Serial data IN 14
LATCH IN 13
Serial CK IN 15
Control
Interface Zero Flag L17
Zero Flag R16
Master Clock 18
D VDD2D GND3
051-6834-00 XC3S50-4VQG100I-0985 FPGA
Terminal Description
pin 1: A20 : Address input.
pin 2: A19 : Address input.
pin 3: GND : Ground.
pin 4: A18 : Address input.
pin 5: A5 : Address input.
pin 6: VCCO : 3.3V power supply for IC.
pin 7: VCCAUX : 2.5V power supply for AUX.
pin 8: A4 : Address input.
pin 9: A3 : Address input.
pin 10: GND : Ground.
pin 11: A2 : Address input.
pin 12: A1 : Address input.
051-6718-90 AK5357VT-E2 96kHz 24Bit ADC
Terminal Description
pin 1: A IN R :IN: R channel audio signal input.
pin 2: A IN L :IN: L channel audio signal input.
pin 3: CK S 1 :IN: Clock Mode select.
pin 4: V COMMON : O : Common voltage output = A VDD/2
pin 5: A GND : - : Analog ground.
pin 6: A VDD : - : Positive voltage supply for analog section.
pin 7: D VDD : - : Positive voltage supply for digital section.
pin 8: D GND : - : Digital ground.
pin 9: SDO : O : Audio Serial data output.
pin 10: LR CK I/O :I/O:Output channel clock. L output in Master
Mode at Power-down mode.
pin 11: MASTER CLK :IN: Master clock input.
pin 12: S CLK :I/O:Audio Serial data clock input. L output in
Master Mode at Power-down mode.
pin 13: PDN :IN: Power down & reset signal input.
L = Power-down mode.
pin 14: DIF :IN: Audio interface format.
H = 24bit I2S compatible
L = 24bit MSB justified
pin 15: CK S 2 :IN: Clock Mode select.
pin 16: CK S 0 :IN: Clock Mode select.
051-6731-90 WM8718SEDS/R
24 bit Differential Stereo DAC with Volume control

NAX963HD
-11-
pin 13: D15 : Data input/output.
pin 14: D14 : Data input/output.
pin 15: D13 : Data input/output.
pin 16: D12 : Data input/output.
pin 17: D11 : Data input/output.
pin 18: VCCINT : 1.2V power supply for Core.
pin 19: VCCO : 3.3V power supply for IC.
pin 20: GND : Ground.
pin 21: D10 : Data input/output.
pin 22: D9 : Data input/output.
pin 23: D8 : Data input/output.
pin 24: M1 : Configuration mode setting.
pin 25: M0 : Configuration mode setting.
pin 26: M2 : Configuration mode setting.
pin 27: CS_B : For Configuration.
pin 28: RDWR_B : Read/Write signal input.
pin 29: GND : Ground.
pin 30: D7 : Data input/output.
pin 31: VCCO : 3.3V power supply for IC.
pin 32: D6 : Data input/output.
pin 33: VCCAUX : 2.5V power supply for AUX.
pin 34: D5 : Data input/output.
pin 35: D4 : Data input/output.
pin 36: NC : Not in use.
pin 37: NC : Not in use.
pin 38: N_SH_RDY : Ready signal output for CPU.
pin 39: CKIO : Clock input.
pin 40: NC : Not in use.
pin 41: GND : Ground.
pin 42: INIT_B : For Configuration.
pin 43: D3 : Data input/output.
pin 44: D2 : Data input/output.
pin 45: VCCINT : 1.2V power supply for Core.
pin 46: VCCO : 3.3V power supply for IC.
pin 47: D1 : Data input/output.
pin 48: D0 : Data input/output.
pin 49: N_WE1 : Write enable input.
pin 50: N_WE0 : Write enable input.
pin 51: DONE : High output after configuration.
pin 52: CCLK : Configuration clock input.
pin 53: N_RD : Read signal input.
pin 54: N_CS_FPGA :Chip select input.
pin 55: NC : Not in use.
pin 56: GND : Ground.
pin 57: VCCO : 3.3V power supply for IC.
pin 58: VCCAUX : 2.5V power supply for AUX.
pin 59: NC : Not in use.
pin 60: NC : Not in use.
pin 61: NC : Not in use.
pin 62: N_EIRQ1 : Interrupt signal output for CPU.
pin 63: NC : Not in use.
pin 64: NC : Not in use.
pin 65: VOL_DATA : Data output to Audio-ADC.
pin 66: GND : Ground.
pin 67: VOL_CLK : Clock output to Audio-ADC.
pin 68: VOL_CS : Chip select output to Audio-ADC.
pin 69: VCCINT : 1.2V power supply for Core.
pin 70: VCCO : 3.3V power supply for IC.
pin 71: EXTCONT : EXT-AUDIO ON/OFF signal for CeNET.
pin 72: N_MUTE : Audio mute.
pin 73: GND : Ground.
pin 74: N_ILL : Illumination detect.
pin 75: NC : Not in use.
pin 76: TDO : For JTAG.
pin 77: TCK : For JTAG.
pin 78: TMS : For JTAG.
pin 79: GYRO_DATA : Data input from GYRO-ADC.
pin 80: ADC_CLK : Clock output to GYRO-ADC.
pin 81: ADC_CS : Chip select output to GYRO-ADC.
pin 82: GND : Ground.
pin 83: VCCO : 3.3V power supply for IC.
pin 84: VCCAUX : 2.5V power supply for AUX.
pin 85: PKB : Parking signal input.
pin 86: N_BACK : Back signal input.
pin 87: NC : Not in use.
pin 88: NC : Not in use.
pin 89: NC : Not in use.
pin 90: N_RESETI : Reset input.
pin 91: SPEED_IN : Speed pulse input.
pin 92: NC : Not in use.
pin 93: VCCINT : 1.2V power supply for Core.
pin 94: VCCO : 3.3V power supply for IC.
pin 95: GND : Ground.
pin 96: A22 : Address input.
pin 97: A21 : Address input.
pin 98: HSWAP_EN : For Configuration.
pin 99: PROG_B : For Configuration.
pin100: TDI : For JTAG.
051-6921-90 TPS2041BDGNR
SINGLE, CURRENT-LIMITED, POWER-DISTRIBUTION SWITCH
OC_ ( pin 5 ):Overcurrent and overtemperature false re-
porting, active-low, open-drain output.
051-6923-08 ADCS7476AIMF 1 M SPS 12 bit ADC
051-7289-90 MC74HC4046ADT PLL
Terminal Description
pin 1: PC P OUT : Phase Comparator Pulse Output
pin 2: PC 1 OUT : Phase Comparator 1 Output
pin 3: COMP IN : Comparator Input
pin 4: VCO OUT : VCO Output
pin 5: INH : Inhibit Input
pin 6: C 1 A : Capacitor C1 Connection A
pin 7: C 1 B : Capacitor C1 Connection B
pin 8: GND : Ground (0 V) VSS
pin 9: VCO IN : VCO Input
pin 10: DEM OUT : Demodulator Output
pin 11: R 1 : Resistor R1 Connection
pin 12: R 2 : Resistor R2 Connection
pin 13: PC 2 OUT : Phase Comparator 2 Output
pin 14: SIG IN : Signal Input
pin 15: PC 3 OUT : Phase Comparator 3 Output
pin 16: VCC : Positive Supply Voltage
1
2
3
4
OUT
OUT
OUT
OC_
GND
IN
IN
EN_ ( L = Switch ON )
8
7
6
5
LOGIC
6
5
4
Chip Select input
Serial data output
Clock pulse input
1
2
3
VDD
GND
Analog signal input : Vin

NAX963HD -12-
051-7529-90 SN74LVC541APW Octal Bus Buffer
Truth Table
Switch G 1 ( pin 1 ) G 2 ( pin 19 )
OFF H H
OFF H L
OFF L H
ON L L
051-7534-90 SN74LVC1G97DCKR
Configurable Multiple-function Gate
Truth Table
Y IN 2 IN 1 IN 0
L L L L
L L L H
H L H L
H L H H
L H L L
H H L H
L H H L
H H H H
051-7537-90 SN74LVC1G14DCKR
Single Schmitt-Trigger Inverter Gate
051-7539-90 SN74LVC3G34DCTR Triple Buffers
051-7503-78 SN74LVCHR16245AGR 8 x 2 Bus Transceiver
Truth Table
OE_ DIR SW 1 SW 2
L L ON OFF
L H OFF ON
H L OFF OFF
H H OFF OFF
051-7505-08 SN74LV08APWR Quad 2-input AND Gate
051-7505-18 SN74ALVC08PWR Quad 2-input AND Gate
051-7520-08 SN74LVC1G04DCKR Single Inverter
051-7522-08 SN74LVC1G32DCKR Single 2-inputs OR Gate
051-7524-08 SN74LVC1G08DCK Single 2-inputs AND GATE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
SW-1SW-2
Logic
SW-1SW-2 Logic
DIR 1
GND
VDD
GND GND GND GND
GND GND GND
VDD VDD
VDD OE 1_ OE 2_DIR 2
14 13 12
11
10
9 8
1 2 3 4 5 6 7GND
VDD
1
2
3
5
4
VCC
OUT
NC
IN
GND
1
2
3
5
4
VCC
GND
1
2
3
5
4
VCC
GND
20 19 18 17 16 15 14 13 12
11
1 2 3 4 5 6 7 8 9
10 GROUND
G1 VCC
G2
Logic
IN 2
VCC
Y
6
5
4
IN 1
GND
IN 0
1
2
3
IN 0 3
IN 1 1
IN 2 6
Y4
1
2
3
N.C.
GND
5
4
VCC
8 7 6 5
GND
VDD
1 2 3 4

NAX963HD
-13-
051-7540-90 SN74LVC2G32DCTR Dual 2-input OR Gate
051-9125-60 BS616LV4013EI-70 4 M bit SRAM
Terminal Description
pin 1: A 4 :IN: Address signal input.
pin 2: A 3 :IN: Address signal input.
pin 3: A 2 :IN: Address signal input.
pin 4: A 1 :IN: Address signal input.
pin 5: A 0 :IN: Address signal input.
pin 6: CE_ :IN: Chip enable signal input.
pin 7: DQ 0 :I/O:The data input / output.
pin 8: DQ 1 :I/O:The data input / output.
pin 9: DQ 2 :I/O:The data input / output.
pin 10: DQ 3 :I/O:The data input / output.
pin 11: VCC : - : Positive supply voltage.
pin 12: GND : - : Ground.
pin 13: DQ 4 :I/O:The data input / output.
pin 14: DQ 5 :I/O:The data input / output.
pin 15: DQ 6 :I/O:The data input / output.
pin 16: DQ 7 :I/O:The data input / output.
pin 17: WE_ :IN: Write enable signal input.
pin 18: A 17 :IN: Address signal input.
pin 19: A 16 :IN: Address signal input.
pin 20: A 15 :IN: Address signal input.
pin 21: A 14 :IN: Address signal input.
pin 22: A 13 :IN: Address signal input.
pin 23: A 12 :IN: Address signal input.
pin 24: A 11 :IN: Address signal input.
pin 25: A 10 :IN: Address signal input.
pin 26: A 9 :IN: Address signal input.
pin 27: A 8 :IN: Address signal input.
pin 28: NU : - : Not in use.
pin 29: DQ 8 :I/O:The data input / output.
pin 30: DQ 9 :I/O:The data input / output.
pin 31: DQ 10 :I/O:The data input / output.
pin 32: DQ 11 :I/O:The data input / output.
pin 33: VCC : - : Positive supply voltage.
pin 34: GND : - : Ground.
pin 35: DQ 12 :I/O:The data input / output.
pin 36: DQ 13 :I/O:The data input / output.
pin 37: DQ 14 :I/O:The data input / output.
pin 38: DQ 15 :I/O:The data input / output.
pin 39: LB_ :IN: Upper byte control signal input.
pin 40: UB_ :IN: Lower byte control signal input.
pin 41: OE_ :IN: Output enable signal input.
pin 42: A 7 :IN: Address signal input.
pin 43: A 6 :IN: Address signal input.
pin 44: A 5 :IN: Address signal input.
Truth Table
CE_ WE_ OE_ LB_ UB_ DQ 0 DQ 8
in in in in in to to
(pin 6) (pin 17) (pin 41) (pin 39) (pin 40) DQ 7 DQ 15
H X X X X high Z high Z
L H H X X high Z high Z
L H L L L output output
L H L H L high Z output
L H L L H output high Z
L L X L L input input
L L X H L X input
L L X L H input X
051-9333-30 MT46V16M16P-6T-IT
256M bit DDR SDRAM (16M words x 16 bits)
Terminal Description
pin 1: VDD : - : Positive voltage supply.
pin 2: DQ 0 :I/O:Data signal input/output.
pin 3: VDD Q : - :Positive power supply for the data I/O
ports.
pin 4: DQ 1 :I/O:Data signal input/output.
pin 5: DQ 2 :I/O:Data signal input/output.
pin 6: VSS Q : - : Ground terminal for the data I/O ports.
pin 7: DQ 3 :I/O:Data signal input/output.
pin 8: DQ 4 :I/O:Data signal input/output.
pin 9: VDD Q : - :Positive power supply for the data I/O
ports.
pin 10: DQ 5 :I/O:Data signal input/output.
pin 11: DQ 6 :I/O:Data signal input/output.
pin 12: VSS Q : - : Ground terminal for the data I/O ports.
pin 13: DQ 7 :I/O:Data signal input/output.
pin 14: NU : - : Not in use.
pin 15:VDD Q : - : Positive power supply for the data I/O
ports.
pin 16: Lower DQ S :I/O:Read data strobe output / Write data
strobe input.
pin 17: NU : - : Not in use.
pin 18: VDD : - : Positive voltage supply.
pin 19: NU : - : Not in use.
pin 20: Lower DM :IN: When this pin is High, the data input are
masked.
pin 21: WE :IN: Write enable signal input.
pin 22: CAS :IN: Column address strobe input.
pin 23: RAS :IN: Row address strobe input.
pin 24: CS IN :IN: The chip select command input.
pin 25: NU : - : Not in use.
pin 26: BA 0 :IN: Bank address input.
pin 27: BA 1 :IN: Bank address input.
pin 28: A10(AP) :IN: Address signal input.
pin 29: A 0 :IN: Address signal input.
pin 30: A 1 :IN: Address signal input.
pin 31: A 2 :IN: Address signal input.
pin 32: A 3 :IN: Address signal input.
pin 33: VDD : - : Positive voltage supply.
pin 34: VSS : - : Negative voltage supply.
pin 35: A 4 :IN: Address signal input.
pin 36: A 5 :IN: Address signal input.
pin 37: A 6 :IN: Address signal input.
pin 38: A 7 :IN: Address signal input.
pin 39: A 8 :IN: Address signal input.
pin 40: A 9 :IN: Address signal input.
pin 41: A 11 :IN: Address signal input.
pin 42: A 12 :IN: Address signal input.
pin 43: NU : - : Not in use.
pin 44: CKE :IN: Clock enable signal input.
pin 45: CK :IN: Master clock input.
pin 46: /CK :IN:Master clock input.
pin 47: Upper DM :IN: When this pin is High, the data input are
8 7 6 5
1 2 3 4GROUND
VDD

NAX963HD -14-
masked.
pin 48: VSS : - : Negative voltage supply.
pin 49: Vref : - : Reference voltage.
pin 50: NU : - : Not in use.
pin 51: Upper DQ S :I/O:Read data strobe output / Write data
strobe input.
pin 52: VSS Q : - : Ground terminal for the data I/O ports.
pin 53: NU : - : Not in use.
pin 54: DQ 8 :I/O:Data signal input/output.
pin 55: VDD Q : - : Positive power supply for the data I/O
ports.
pin 56: DQ 9 :I/O:Data signal input/output.
pin 57: DQ 10 :I/O:Data signal input/output.
pin 58: VSS Q : - : Ground terminal for the data I/O ports.
pin 59: DQ 11 :I/O:Data signal input/output.
pin 60: DQ 12 :I/O:Data signal input/output.
pin 61: VDD Q : - : Positive power supply for the data I/O
ports.
pin 62: DQ 13 :I/O:Data signal input/output.
pin 63: DQ 14 :I/O:Data signal input/output.
pin 64: VSS Q : - : Ground terminal for the data I/O ports.
pin 65: DQ 15 :I/O:Data signal input/output.
pin 66: VSS : - : Negative voltage supply.
IC103 R8A77700ADA01BGV
RISC Microcomputer for QY5000EA
Terminal Description
pin 1: VSSQ25 : DDR ground
pin 2: VCCQ25 : DDR 2.5V power supply
pin 3: DSA[6] : DDR-SDRAM address output
pin 4: DSA[4] : DDR-SDRAM address output
pin 5: DSA[2] : DDR-SDRAM address output
pin 6: DSA[0] : DDR-SDRAM address output
pin 7: DSRAS# : DDR-SDRAM row address select output
pin 8: DSCAS# : DDR-SDRAM column address select out-
put
pin 9: DSDQ[36] : DDR-SDRAM data input/output
pin 10: DSDM[4] : DDR-SDRAM data select output
pin 11: DSDQ[39] : DDR-SDRAM data input/output
pin 12: DSDQ[45] : DDR-SDRAM data input/output
pin 13: DSDM[5] : DDR-SDRAM data select output
pin 14: DSDQ[46] : DDR-SDRAM data input/output
pin 15: DSDQ[52] : DDR-SDRAM data input/output
pin 16: DSDM[6] : DDR-SDRAM data select output
pin 17: DSDQ[55] : DDR-SDRAM data input/output
pin 18: DSDQ[61] : DDR-SDRAM data input/output
pin 19: DSDM[7] : DDR-SDRAM data select output
pin 20: DSDQ[63] : DDR-SDRAM data input/output
pin 21: TX0/MD［2］: In the reset operation, this port is CPU
setting input. At usually operation, this
port is serial data output to GPS receiv-
er.
pin 22: TX1/MD［3］: In the reset operation, this port is CPU
setting input. At usually operation, this
port is not in use.
pin 23: TX3/IrDA-TX/MD[5] : In the reset operation, this port is CPU
setting input. At usually operation, this
port is not in use.
pin 24: TX5/HSPI0_CLK : Serial data output to RDS microcomput-
er.
pin 25: NU : Not in use.
pin 26: NU : Not in use.
pin 27: NU : Not in use.
pin 28: NU : Not in use.
pin 29: VSSDLL : DLL ground
pin 30: VDDPLL1 : PLL 1.25V power supply
pin 31: VSSPLL1 : PLL ground
pin 32: VCCQ25 : DDR 2.5V power supply
pin 33: VSSQ25 : DDR ground
pin 34: VCCQ25 : DDR 2.5V power supply
pin 35: DSA[7] : DDR-SDRAM address output
pin 36: DSA[3] : DDR-SDRAM address output
pin 37: DSA[1] : DDR-SDRAM address output
pin 38: DSBA[0] : DDR-SDRAM bank address output
pin 39: /DSWE : DDR-SDRAM write enable.
pin 40: DSDQ[32] : DDR-SDRAM data input/output
pin 41: DSDQS[4] : DDR-SDRAM data input/output
pin 42: DSDQ[35] : DDR-SDRAM data input/output
pin 43: DSDQ[41] : DDR-SDRAM data input/output
pin 44: DSDQS[5] : DDR-SDRAM data strobe input/output
pin 45: DSDQ[42] : DDR-SDRAM data input/output
pin 46: DSDQ[48] : DDR-SDRAM data input/output
pin 47: DSDQS[6] : DDR-SDRAM data strobe input/output
pin 48: DSDQ[51] : DDR-SDRAM data input/output
pin 49: DSDQ[57] : DDR-SDRAM data input/output
pin 50: DSDQS[7] : DDR-SDRAM data strobe input/output
pin 51: DSDQ[59] : DDR-SDRAM data input/output
pin 52: RX0 : GPS serial data input
pin 53: NU : Not in use.
pin 54: NU : Not in use.
pin 55: RX5/HSPI0_CS# : Serial data input from RDS microcomput-
er.
pin 56: NU : Not in use.
pin 57: NU : Not in use.
pin 58: NU : Not in use.
pin 59: TX6/MD[10] : In the reset operation, this port is CPU
setting input. At usually operation, this
port is not in use.
pin 60: VDDDLL : DLL 1.25V power supply
pin 61: VDDPLL2 : PLL 1.25V power supply
pin 62: VSSPLL2 : PLL ground
pin 63: VCCQ25 : DDR 2.5V power supply
pin 64: VCCQ25 : DDR 2.5V power supply
pin 65: VSSQ25 : DDR ground
pin 66: VCCQ25 : DDR 2.5V power supply
pin 67: DSA[5] : DDR-SDRAM address output
pin 68: DSBA[1] : DDR-SDRAM bank address output
pin 69: VSSQ25 : DDR ground
pin 70: NU : Not in use.
pin 71: DSDQ[37] : DDR-SDRAM data input/output
pin 72: DSDQ[38] : DDR-SDRAM data input/output
pin 73: DSDQ[44] : DDR-SDRAM data input/output
pin 74: VCCQ25 : DDR 2.5V power supply
pin 75: VSSQ25 : DDR ground
pin 76: DSDQ[47] : DDR-SDRAM data input/output
pin 77: DSDQ[53] : DDR-SDRAM data input/output
pin 78: DSDQ[54] : DDR-SDRAM data input/output
pin 79: DSDQ[60] : DDR-SDRAM data input/output
pin 80: VCCQ25 : DDR 2.5V power supply
pin 81: DSDQ[62] : DDR-SDRAM data input/output
pin 82: NU : Not in use.
pin 83: VSSQ25 : DDR ground
pin 84: TX2/MD[4] : In the reset operation, this port is CPU
setting input. At usually operation, this
port is serial data output.
pin 85: TX4/HSPI0_TX : Serial data output
pin 86: TX7/HSPI1_TX :Serial data output to sub-microcomputer

NAX963HD
-15-
pin 87: NU : Not in use.
pin 88: TX9/GPIO_2A20 : Used as GPIO. /P_OFF
pin 89: NU : Not in use.
pin 90: VSSQ : I/O power ground
pin 91: VCCQ : I/O 3.3V power supply
pin 92: VCCQ : I/O 3.3V power supply
pin 93: EXTAL : External clock input (48MHz)
pin 94: DSCK# : DDR-SDRAM clock output (inverted)
pin 95: DSCAP : DDR-SDRAM controller CAP
pin 96: VCCQ25 : DDR 2.5V power supply
pin 97: VSSQ25 : DDR ground
pin 98: VCCQ25 : DDR 2.5V power supply
pin 99: DSA[10] : DDR-SDRAM address output
pin100:VSSQ25 : DDR ground
pin101:DSCS# : DDR-SDRAM area space selection
pin102:DSDQ[33] : DDR-SDRAM data input/output
pin103:DSDQ[34] : DDR-SDRAM data input/output
pin104:DSDQ[40] : DDR-SDRAM data input/output
pin105:VCCQ25 : DDR 2.5V power supply
pin106:VSSQ25 : DDR ground
pin107:DSDQ[43] : DDR-SDRAM data input/output
pin108:DSDQ[49] : DDR-SDRAM data input/output
pin109:DSDQ[50] : DDR-SDRAM data input/output
pin110:DSDQ[56] : DDR-SDRAM data input/output
pin111:VCCQ25 : DDR 2.5V power supply
pin112:DSDQ[58] : DDR-SDRAM data input/output
pin113:NU : Not in use.
pin114:VSSQ25 : DDR ground
pin115:RX2 :Serial data input
pin116:RX4/HSPI0_RX :Serial data input
pin117:RX7/HSPI1_RX : Serial data input from sub-microcomput-
er
pin118:NU : Not in use.
pin119:RX9/GPIO_2A21 : Used as GPIO. /BU_DET
pin120:VSSQ :I/O power ground
pin121:VCCQ : I/O 3.3V power supply
pin122:VSSQ :I/O power ground
pin123:VSSQ :I/O power ground
pin124:XTAL : CPU crystal connection
pin125:DSCK : DDR-SDRAM clock output
pin126:NU : Not in use.
pin127:VCCQ25 : DDR 2.5V power supply
pin128:VCCQ25 : DDR 2.5V power supply
pin129:VSSQ25 : DDR ground
pin130:VCCQ25 : DDR 2.5V power supply
pin131:VSSQ25 : DDR ground
pin132:VCCQ25 : DDR 2.5V power supply
pin133:VSSQ25 : DDR ground
pin134:VDD : Core 1.25V power supply
pin135:VSS : Core power ground
pin136:VCCQ25 : DDR 2.5V power supply
pin137:VSSQ25 : DDR ground
pin138:VCCQ25 : DDR 2.5V power supply
pin139:VSSQ25 : DDR ground
pin140:VDD : Core 1.25V power supply
pin141:VSS : Core power ground
pin142:VCCQ25 : DDR 2.5V power supply
pin143:VSSQ25 : DDR ground
pin144:VDD : Core 1.25V power supply
pin145:VSSQ25 : DDR ground
pin146:VSS : Core power ground
pin147:VSSQ :I/O power ground
pin148:VCCQ : I/O 3.3V power supply
pin149:VCCQ : I/O 3.3V power supply
pin150:VSSQ :I/O power ground
pin151:VCCQ : I/O 3.3V power supply
pin152:VSSQ :I/O power ground
pin153:TRST# : H-UDI reset input
pin154:NU : Not in use.
pin155:NU : Not in use.
pin156:DSA[11] : DDR-SDRAM address output
pin157:DSA[12] : DDR-SDRAM address output
pin158:DSA[8] : DDR-SDRAM address output
pin159:DSA[9] : DDR-SDRAM address output
pin160:VCCQ25 : DDR 2.5V power supply
pin161:VSSQ :I/O power ground
pin162:TMS : H-UDI mode input
pin163:TDI : H-UDI data input
pin164:TDO : H-UDI data output
pin165:TCK : H-UDI clock input
pin166:DSCKE : DDR-SDRAM clock output enable
pin167:NU : Not in use.
pin168:DSA[13] : DDR-SDRAM address output
pin169:VSSQ25 : DDR ground
pin170:VSSQ25 : DDR ground
pin171:VCCQ : I/O 3.3V power supply
pin172:NU : Not in use.
pin173:NU : Not in use.
pin174:NU : Not in use.
pin175:NU : Not in use.
pin176:DSDQ[30] : DDR-SDRAM data input/output
pin177:DSDQ[26] : DDR-SDRAM data input/output
pin178:DSDQ[31] : DDR-SDRAM data input/output
pin179:DSDQ[27] : DDR-SDRAM data input/output
pin180:VDD :Core 1.25V power supply
pin181:VSS : Core power ground
pin182:NU : Not in use.
pin182:NU : Not in use.
pin184:ASEBRK# : Emulator input/output（brake,
acknowledge）
pin185:NU : Not in use.
pin186:DSDQ[29] : DDR-SDRAM data input/output
pin187:DSDQ[25] : DDR-SDRAM data input/output
pin188:DSDM[3] : DDR-SDRAM data select output
pin189:DSDQS[3] :DDR-SDRAM data input/output
pin190:VSS : Core power ground
pin191:VDD :Core 1.25V power supply
pin192:NU : Not in use.
pin193:NU : Not in use.
pin194:NU : Not in use.
pin195:NU : Not in use.
pin196:DSDQ[23] : DDR-SDRAM data input/output
pin197:DSDQ[19] : DDR-SDRAM data input/output
pin198:DSDQ[28] : DDR-SDRAM data input/output
pin199:DSDQ[24] : DDR-SDRAM data input/output
pin200:VCCQ25 : DDR 2.5V power supply
pin201:VSS : Core power ground
pin202:NU : Not in use.
pin203:NU : Not in use.
pin204:NU : Not in use.
pin205:NU : Not in use.
pin206:DSDM[2] : DDR-SDRAM data select output

NAX963HD -16-
pin207:DSDQS[2] : DDR-SDRAM data strobe input/output
pin208:DSDQ[22] : DDR-SDRAM data input/output
pin209:DSDQ[18] : DDR-SDRAM data input/output
pin210:VSSQ25 : DDR ground
pin211:VDD : Core 1.25V power supply
pin212:NU : Not in use.
pin213:NU : Not in use.
pin214:NU : Not in use.
pin215:NU : Not in use.
pin216:DSDQ[20] : DDR-SDRAM data input/output
pin217:DSDQ[16] : DDR-SDRAM data input/output
pin218:DSDQ[21] : DDR-SDRAM data input/output
pin219:DSDQ[17] : DDR-SDRAM data input/output
pin220:VDD : Core 1.25V power supply
pin221:VSSQ :I/O power ground
pin222:SPDIF_IN : Extended GPIO data latch output
pin223:SPDIF_OUT : FPGA PROG_B output
pin224:NU : Not in use.
pin225:NU : Not in use.
pin226:DSDQ[14] : DDR-SDRAM data input/output
pin227:DSDQ[10] : DDR-SDRAM data input/output
pin228:DSDQ[15] : DDR-SDRAM data input/output
pin229:DSDQ[11] : DDR-SDRAM data input/output
pin230:VSS : Core power ground
pin231:VCCQ : I/O 3.3V power supply
pin232:SSI_SDATA１: Data output to DAC for guide signal
pin233:SSI_SDATA0 : The data input from ADC for microphone
pin234:NU : Not in use.
pin235:AUDIO_CLK : Audio clock input for SSI module
(8.46MHz)
pin236:DSDM[1] : DDR-SDRAM data select output
pin237:DSDQS[1] : DDR-SDRAM data strobe input/output
pin238:VSSQ25 : DDR ground
pin239:VSSQ25 : DDR ground
pin240:VSSQ25 : DDR ground
pin241:VSS : Core power ground
pin242:SSI_WS0 : LR clock input
pin243:SSI_SCK0 : Serial bit clock input
pin244:SSI_WS1/HAC_RES#
: LR clock input
pin245:SSI_SCK1 : Serial bit clock input
pin246:DSDQ[12] : DDR-SDRAM data input/output
pin247:DSDQ[8] : DDR-SDRAM data input/output
pin248:DSDQ[13] : DDR-SDRAM data input/output
pin249:DSDQ[9] : DDR-SDRAM data input/output
pin250:VSSQ25 : DDR ground
pin251:VSS : Core power ground
pin252:NU : Not in use.
pin253:NU : Not in use.
pin254:NU : Not in use.
pin255:NU : Not in use.
pin256:DSDQ[6] : DDR-SDRAM data input/output
pin257:DSDQ[2] : DDR-SDRAM data input/output
pin258:DSDQ[7] : DDR-SDRAM data input/output
pin259:DSDQ[3] : DDR-SDRAM data input/output
pin260:VCCQ25 : DDR 2.5V power supply
pin261:VSSQ :I/O power ground
pin262:IDED[7] : IDE data input/output
pin263:IDED[8] : IDE data input/output
pin264:IDERST# : IDE reset output
pin265:DIRECTION : IDE bus buffer direction control output
pin266:DSDQ[5] : DDR-SDRAM data input/output
pin267:DSDQ[1] : DDR-SDRAM data input/output
pin268:DSDM[0] : DDR-SDRAM data select output
pin269:DSDQS[0] : DDR-SDRAM data strobe input/output
pin270:VSSQ25 : DDR ground
pin271:VCCQ : I/O 3.3V power supply
pin272:IDED[5] : IDE data input/output
pin273: IDED[10] : IDE data input/output
pin274:IDED[6] : IDE data input/output
pin275:IDED[9] : IDE data input/output
pin276:DSDQ[4] : DDR-SDRAM data input/output
pin277:DSDQ[0] : DDR-SDRAM data input/output
pin278:VCCQ25 : DDR 2.5V power supply
pin279:VCCQ25 : DDR 2.5V power supply
pin280:VCCQ25 : DDR 2.5V power supply
pin281: VDD :Core 1.25V power supply
pin282:IDED[3] : IDE data input/output
pin283: IDED[12] : IDE data input/output
pin284:IDED[4] : IDE data input/output
pin285: IDED[11] : IDE data input/output
pin286:DSVREF : DDR-SDRAM reference voltage input
pin287:VSS : Core power ground
pin288:VSS : Core power ground
pin289:VSS : Core power ground
pin290:VSS : Core power ground
pin291:VSS : Core power ground
pin292:IDED[1] : IDE data input/output
pin293: IDED[14] : IDE data input/output
pin294:IDED[2] : IDE data input/output
pin295: IDED[13] : IDE data input/output
pin296: VDD :Core 1.25V power supply
pin297: VDD :Core 1.25V power supply
pin298: VDD :Core 1.25V power supply
pin299: VDD :Core 1.25V power supply
pin300: VDD :Core 1.25V power supply
pin301:VCCQ : I/O 3.3V power supply
pin302:IDEIOWR# : IDE disk write output
pin303:IODREQ : IDE-DMA request input
pin304:IDED[0] : IDE data input/output
pin305: IDED[15] : IDE data input/output
pin306:NU : Not in use.
pin307:NU : Not in use.
pin308:VSS : Core power ground
pin309:VSS : Core power ground
pin310:VSS : Core power ground
pin311:VSSQ :I/O power ground
pin312:IDEINT : IDE interrupt request input
pin313:IODACK# : IDE-DMA acknowledge output
pin314:IDEIORDY : IDE ready input
pin315:IDEIORD# : IDE disk resd output
pin316:NMI# : NMI
pin317:IRQ#[4]/EX_CS#[6] : Interrupt input
pin318:IRQ#[5]/EX_CS#[7] : Chip select output
pin319:IRQ#[1]/EX_WAIT[1]
: Interrupt input
pin320: VDD :Core 1.25V power supply
pin321: VDD :Core 1.25V power supply
pin322:IDECS#[0] : IDE chip select output
pin323:IDEA[2] : IDE address output
pin324:IDEA[0] : IDE address output
pin325:IDEA[1] : IDE address output

NAX963HD
-17-
pin326:NU : Not in use.
pin327:IRQ#[0] : Interrupt input
pin328:NU : Not in use.
pin329:NU : Not in use.
pin330:VSSQ :I/O power ground
pin331:VSS : Core power ground
pin332:NU : Not in use.
pin333:NU : Not in use.
pin334:NU : Not in use.
pin335:IDECS#[1] : IDE chip select output
pin336:NU : Not in use.
pin337:NU : Not in use.
pin338:NU : Not in use.
pin339:NU : Not in use.
pin340:VCCQ : I/O 3.3V power supply
pin341:VDD : Core 1.25V power supply
pin342:GPIO-3-A27 : LED1 control signal output to sub-micro-
computer
pin343:GPIO-3-A28 : LED2 control signal output to sub-micro-
computer
pin344:IRREC : Remote control input
pin346:NU : Not in use.
pin347:NU : Not in use.
pin348:NU : Not in use.
pin349:NU : Not in use.
pin350:VSSQ :I/O power ground
pin351:VSS : Core power ground
pin352:VSSRTC : RTC ground
pin353:NU : Not in use.
pin354:RESOUT# : Reset output
pin355:RESET# : Reset input
pin355:RESET# : Reset input
pin356:NU : Not in use.
pin357:NU : Not in use.
pin358:NU : Not in use.
pin359:NU : Not in use.
pin360:VCCQ : I/O 3.3V power supply
pin361:VCCQ : I/O 3.3V power supply
pin362:NU : Not in use.
pin363:NU : Not in use.
pin364:NU : Not in use.
pin365:NU : Not in use.
pin366:NU : Not in use.
pin367:NU : Not in use.
pin368:EX_CS#[4]/EXCPU_IRQ#
: Chip select output
pin369:VCCQ : I/O 3.3V power supply
pin370:VSSQ :I/O power ground
pin371:VCCQ : I/O 3.3V power supply
pin372:VSSQ :I/O power ground
pin373:VCCQ : I/O 3.3V power supply
pin374:VSSQ :I/O power ground
pin375:VCCQ : I/O 3.3V power supply
pin376:VSS : Core power ground
pin377:VDD : Core 1.25V power supply
pin378:VSSQ :I/O power ground
pin379:VCCQ : I/O 3.3V power supply
pin380:VSSQ :I/O power ground
pin381:VCCQ : I/O 3.3V power supply
pin382:VSS : Core power ground
pin383:VDD : Core 1.25V power supply
pin384:VSSQ : I/O power ground
pin385:VCCQ : I/O 3.3V power supply
pin386:VSSQ : I/O power ground
pin387:VCCQ : I/O 3.3V power supply
pin388:VSS : Core power ground
pin389: VDD :Core 1.25V power supply
pin390:VSSQ :I/O power ground
pin391:VCCQ : I/O 3.3V power supply
pin392:VSSQ :I/O power ground
pin393:VCCQ : I/O 3.3V power supply
pin394:VCCRTC : RTC power supply 3.3V
pin395:NU : Not in use.
pin396:NU : Not in use.
pin397: WE#[2] : EXBUS write enable output
pin398: WE#[3] : EXBUS write enable output
pin399:VCCQ : I/O 3.3V power supply
pin400:VSSQ :I/O power ground
pin401:VCCQ : I/O 3.3V power supply
pin402:D[4] : EXBUS data input/output
pin403:D[0] : EXBUS data input/output
pin404: WE#[1] : EXBUS write enable output
pin405:EX_CS#[1] : EXBUS extended area chip select output
pin406:RD/WR# : EXBUS read/write
pin407:NU : Not in use.
pin408:NU : Not in use.
pin409:NU : Not in use.
pin410:A[3] : EXBUS Address output.
pin411:A[7] : EXBUS Address output.
pin412:A[8] : EXBUS Address output.
pin413:A[15] : EXBUS Address output.
pin414:A[19] : EXBUS Address output.
pin415:A[23] : EXBUS Address output.
pin416:NU : Not in use.
pin417:VSSQ :I/O power ground
pin418:VCCQ : I/O 3.3V power supply
pin419:NU : Not in use.
pin420:NU : Not in use.
pin421:GPIO-3-A25 :PLL 4fsc/K output
pin422:VSSA : Analog ground
pin423:CBU :DAC capacitor connection
pin424:VSSQ :I/O power ground
pin425:VCCQ : I/O 3.3V power supply
pin426:NU : Not in use.
pin427:VSSA : Analog ground
pin428: RD# : EXBUS read output
pin429:NU : Not in use.
pin430:VSSQ :I/O power ground
pin431:D[11] : EXBUS data input/output
pin432:D[8] : EXBUS data input/output
pin433:D[5] : EXBUS data input/output
pin434:D[1] : EXBUS data input/output
pin435: WE#[0] : EXBUS write enable output
pin436:EX_CS#[0] : EXBUS extended area chip select output
pin437:EX_WAIT[0]/EXCPU_RDY#
: EXBUS extended area external weight
signal input
pin438:NU : Not in use.
pin439:NU : Not in use.
pin440:NU : Not in use.
pin441:A[2] : EXBUS Address output.
pin442:A[6] : EXBUS Address output.

NAX963HD -18-
pin443:A[9] : EXBUS Address output.
pin444:A[14] : EXBUS Address output.
pin445:A[18] : EXBUS Address output.
pin446:A[22] : EXBUS Address output.
pin447:NU : Not in use.
pin448:OVC :USB over current detection
pin449:NU : Not in use.
pin450:DISP/CSYNC#/DE : CSYNC signal output
pin451:NU : Not in use.
pin452:GPIO-3-A26 :PLL Dclk/N output
pin453:NU : Not in use.
pin454:REXT : DAC external reference
pin455:VCCA : Analog 3.3V power supply
pin456:VSSQ :I/O power ground
pin457:NU : Not in use.
pin458:NU : Not in use.
pin459:VSSQ :I/O power ground
pin460:VSSQ :I/O power ground
pin461:D[14] : EXBUS data input/output
pin462:D[12] : EXBUS data input/output
pin463:D[9] : EXBUS data input/output
pin464:D[6] : EXBUS data input/output
pin465:D[2] : EXBUS data input/output
pin466:NU : Not in use.
pin467:NU : Not in use.
pin468:NU : Not in use.
pin469:NU : Not in use.
pin470:NU : Not in use.
pin471:NU : Not in use.
pin472:A[1] : EXBUS Address output.
pin473:A[5] : EXBUS Address output.
pin474:A[11] : EXBUS Address output.
pin475:A[13] : EXBUS Address output.
pin476:A[17] : EXBUS Address output.
pin477:A[21] : EXBUS Address output.
pin478:A[25] : EXBUS Address output.
pin479:PENC : USB power enable output
pin480:HP : USB port D+
pin481:NU : Not in use.
pin482:NU : Not in use.
pin483:VSSQ :I/O power ground
pin484:NC3 / 4fscEXCLK : 4fsc clock (14.31818MHz)
pin485:AG : Video signal Green output
pin486:VSSA : Analog ground
pin487:NU : Not in use.
pin488:VSSQ :I/O power ground
pin489:VCCA : Analog 3.3V power supply
pin490:VCCQ : I/O 3.3V power supply
pin491:VCCQ : I/O 3.3V power supply
pin492:D[15] : EXBUS data input/output
pin493:D[13] : EXBUS data input/output
pin494:D[10] : EXBUS data input/output
pin495:D[7] : EXBUS data input/output
pin496:D[3] : EXBUS data input/output
pin497:EX_CS#[2]/EXCPU_CS#[0]
: Chip select output
pin498:CS#[0] :Chip select output
pin499:CLK ＯＵＴ : CKIO output (32MHz)
pin500:NU : Not in use.
pin501:NU : Not in use.
pin502:NU : Not in use.
pin503:A[0] : Not in use.
pin504:A[4] : EXBUS Address output.
pin505:A[10] : EXBUS Address output.
pin506:A[12] : EXBUS Address output.
pin507:A[16] : EXBUS Address output.
pin508:A[20] : EXBUS Address output.
pin509:A[24] : EXBUS Address output.
pin510:USBCLK : USB clock input (48MHz)
pin511:HM : USB port D-
pin512:NU : Not in use.
pin513:DOTCLKIN : Dot clock input
pin514:NU : Not in use.
pin515:NU : Not in use.
pin516:AR : Video signal Red output
pin517:AB : Video signal Blue output
pin518:NU : Not in use.
pin519:VSSQ :I/O power ground
pin520:VCCA : Analog 3.3V power supply
052-1325-00 M30621MCA-FX2GP RDS-TMC
Terminal Description
pin 1: NU : - : Not in use.
pin 2: NU : - : Not in use.
pin 3: NU : - : Not in use.
pin 4: NU : - : Not in use.
pin 5: RDS CLK :IN: RDS clock pulse input.
pin 6: NU : - : Not in use.
pin 7: NU : - : Not in use.
pin 8: NU : - : Not in use.
pin 9: RESET :IN: Reset signal input.
pin 10: X out : O : Crystal connection.
pin 11: VSS : - : Negative voltage supply.
pin 12: X in :IN: Crystal connection.
pin 13: VCC : - : Positive voltage supply.
pin 14: NU : - : Not in use.
pin 15: ACC DET :IN: ACC detection signal input.
pin 16: NU : - : Not in use.
pin 17: B/U DET :IN: Backup voltage ON signal input.
pin 18: NU : - : Not in use.
pin 19: NU : - : Not in use.
pin 20: NU : - : Not in use.
pin 21: NU : - : Not in use.
pin 22: SH RX :IN: Serial data input from SH.
pin 23: SH TX : O : Serial data output to SH.
pin 24: NU : - : Not in use.
pin 25: NU : - : Not in use.
pin 26: NU : - : Not in use.
pin 27: NU : - : Not in use.
pin 28: NU : - : Not in use.
pin 29: NU : - : Not in use.
pin 30: NU : - : Not in use.
pin 31: NU : - : Not in use.
pin 32: SYS ON : O : System ON signal output.
pin 33: NU : - : Not in use.
pin 34: NU : - : Not in use.
pin 35: NU : - : Not in use.
pin 36: NU : - : Not in use.
pin 37: NU : - : Not in use.
pin 38: NU : - : Not in use.
pin 39: NU : - : Not in use.
pin 40: NU : - : Not in use.
pin 41: NU : - : Not in use.
pin 42: NU : - : Not in use.