Clarion DXZ945MP User manual

DXZ945MP
DXZ946MP
-1-
Published by Service Dept.
Printed in Japan
Clarion Co., Ltd.
50Kamitoda,Toda-shi,Saitama335-8511Japan
ServiceDept.: 5-66Azuma,Kitamoto-shi,Saitama364-0007Japan
Tel:[phone] FAX: [phone]
298-6140-00 Dec.2003 P
Service Manual
Model
Model
AM/FM CD/MP3/WMA Player
Built-in DSP/EQ With Touchpanel
(PE-2635B-A / For U.S.A.)
(PE-2635K-A / For other countries)
(PE-2635K-B / For other countries)
SPECIFICATIONS
FM tuner section
Frequency range: 87.9MHz to 107.9MHz(U.S.A.)
87.0MHz to 108.0MHz(OTHERS)
Usable sensitivity: 9dBf
50dB quieting sensitivity: 15dBf
Alternate channel selectivity:
70dB
Stereo separation: 35dB (1kHz)
Frequency response: 30Hz to 15kHz (+/-3dB)
AM tuner section
Frequency range: 530kHz to 1710kHz(U.S.A.)
531kHz to 1629kHz(OTHERS)
Usable sensitivity: 25uV
CD player section
System: Compact disc digital audio system
Usable discs: Compact disc
Frequency response: 5Hz to 20kHz (+/-1dB)
S/N ratio: 100dB (1kHz)
Dynamic range: 96dB (1kHz)
Distortion: 0.01%
MP3/WMA mode
MP3 sampling rate: 11.025kHz to 48kHz
MP3 bit rate: 8kbps to 320kbps/VBR
WMA bit rate: 48kbps to 192kbps
Logical format: ISO9660 level1,2
JOLIET or Romeo
Audio section
Maximum power output: 53Wx4
Continous average power output:
18Wx4, into 4ohm, 20Hz to 20kHz,
1%THD
Line output level: 4V/F 2ch+4V/R 2ch (CD 1kHz)
4V/NON-FADER 2ch (CD 1kHz)
0.5V/2-ZONE 2ch (CD 1kHz)
Bass control action: +/-12dB (50Hz)
Treble control action: +/-12dB (12.5kHz)
General
Power supply voltage: 14.4V DC(10.8V to 15.6V allow-
able) negative ground
Current consumption: Less than 15A,3A
Speaker impedance: 4ohm(4ohm to 8ohm allowable)
Dimensions(mm):
Source unit; 178(W)x50(H)x155(D)
Remote control unit; 32(W)x56(H)x24(D)
Weight:
Source unit; 1.7kg
Remote control unit; 80g(including battery)
NOTES
* Use only compact discs bearing the or mark.
* Some CDs recorded in CD-R/CD-RW mode may not be
usable.
* WMA is the abbreviation of Windows Media Audio, an
audio file format developed by Microsoft Corporation.
*, and the Windows logo are trade-
marks, or registerd trademarks of Microsoft Corporation
in the United States and/or other countries.
* This product includes technology owned by Microsoft Cor-
poration and cannot be used or distributed without a li-
cense from MSLGP.
* This product is manufactured under license from Dolby
Laboratories."Dolby","Pro Logic" and the double-D sym-
bol are trademarks of Dolby Laboratories.
* We cannot supply PWB with component parts in principle.
When a circuit on PWB has failure, please repair it by
component parts base. Parts which are not mentioned in
service manual are not supplied.
* Specifications and design are subject to change without
notice for further improvement.

DXZ945MP
DXZ946MP -2-
To engineers in charge of repair or
inspection of our products.
Before repair or inspection, make sure to follow the
instructions so that customers and Engineers in
charge of repair or inspection can avoid suffering
any risk or injury.
1. Use specified parts.
The system uses parts with special safety features against
fire and voltage. Use only parts with equivalent character-
istics when replacing them.
The use of unspecified parts shall be regarded as remod-
eling for which we shall not be liable. The onus of product
liability (PL) shall not be our responsibility in cases where
an accident or failure is as a result of unspecified parts
being used.
2. Place the parts and wiring back in their original positions
after replacement or re-wiring.
For proper circuit construction, use of insulation tubes,
bonding, gaps to PWB, etc, is involved. The wiring con-
nection and routing to the PWB are specially planned using
clamps to keep away from heated and high voltage parts.
Ensure that they are placed back in their original positions
after repair or inspection.
If extended damage is caused due to negligence during
repair, the legal responsibility shall be with the repairing
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se-
curely in their original position after repair. Ensure for safety
reasons there is no possibility of secondary ploblems
around the repaired spots.
If extended damage is caused due to negligence of repair,
the legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the
parts for the automobile.
Disconnect the battery terminal after turning the ignition
key off. If wrong wiring connections are made with the
battery connected, a short circuit and/or fire may occur. If
extensive damage is caused due to negligence of repair,
the legal responsibility shall be with the repairing company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality is
observed in their appearance. Always replace them with
new ones. (The chip parts include resistors, capacitors,
diodes, transistors, etc). The negative pole of tantalum
capacitors is highly susceptible to heat, so use special care
when replacing them and check the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the
iron tip temperature is around 270 . Take care not to ap-
ply the iron tip repeatedly(more than three times)to the
same patterns. Also take care not to apply the tip with force.
7. Turn the unit OFF during disassembly and parts replace-
ment. Recheck all work before you apply power to the unit.
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the la-
ser optical diode lights up, keep your eyes more than 30cms
away from the lens. Prolonged viewing of the laser within
30cms may damage your eyesight.
9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body. Make
sure to avoid electrostatic charges on your clothes or body,
or discharge static electricity before handling the optical
pickup.
9-1. Laser diode
The laser diode terminals are shorted for transporta-
tion in order to prevent electrostatic damage. After
replacement, open the shorted circuit. When remov-
ing the pickup from the mechanism, short the termi-
nals by soldering them to prevent this damage.
9-2. Actuator
The actuator has a powerful magnetic circuit. If a
magnetic material is put close to it. Its characteris-
tics will change. Ensure that no foreign substances
enter through the ventilation slots in the cover.
9-3. Cleaning the lens
Dust on the optical lens affects performance. To
clean the lens, apply a small amount of isopropyl
alcohol to lens paper and wipe the lens gently.
COMPONENTS
PE-2635B-A,PE-2635K-A,PE-2635K-B
1. Main unit ----------- 1
2. Rmote controller RCB-164-600 1
3. Battery(SUM-3) ----------- 2
4. Mounting bracket 300-4976-00 1
5. Universal MTG-bracket 300-7742-00 1
6. DCP case 335-5734-30 1
7. Outer escutcheon(*B-A) 370-6089-00 1
8. Outer escutcheon(*K-A/B) 370-6089-01 1
9. Extension lead 854-6349-50 1
10. Parts bag -----------
10-1. Removal key 331-2497-00 2
10-2. Screw(M5x8) 716-0496-01 1
10-3. Pad screw(M1.7x6)(*B-A) 716-0872-11 1
CAUTIONS
Use of controls, adjustment or performance of procedures
other than those specified herein, may result in hazardous
radiation exposure.
The COMPACT DISC player should not be adjusted or re-
paired by anyone except properly qualified service person-
nel.
Bottom view
of DXZ945MP
*B-A: For DXZ945MP (PE-2635B-A)
*K-A/B: For DXZ946MP (PE-2635K-A/B)

DXZ945MP
DXZ946MP
-3-
ERROR DISPLAYS
TROUBLESHOOTING
ERROR 2
ERROR 3
ERROR 6
AMP GUARD
ERROR 2
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR P
ERROR R
A DISC is caught inside the CD deck and is not ejected.
A DISC cannot be played due to scratches,etc.
A DISC is loaded upside-down inside the CD deck and does not
play.
The speaker protection circuit is operating.During this operation,
if any volume operation is performed, the display shows
"AMP GUARD".
"AMP GUARD" sometimes functions when special test signals are
used.
A DISC inside the CD changer is not loaded.
A DISC inside the CD changer cannot be played due to scratches,
etc.
A DISC inside the CD changer cannot be played because it is
loaded upside-down.
A DISC inside the DVD changer cannot be played.
A DISC cannot be played due to scratches,etc.
A DISC inside the DVD changer cannot be played because it is
loaded upside-down.
Parental level error
Region code error
This is a failure of CD deck's mechanism.
Replace with a non-scratched,non-warped-disc.
Eject the disc then reload it properly.
This is a failure of CD changer's mechanism.
Replace with a non-scratched, non-warped disc.
Eject the disc then reload it properly.
This is a failure of DVD mechanism.
Retry or replace with a non-scratched, non-warped-disc.
Eject the disc then reload it properly.
Set the correct Parental level.
Eject the disc and replace correct region code disc.
CD/MP3/WMAGeneral
DVD changer
CD changer
Cause Measure
Error Display
Turn down sound volume. Function can also be restored by
turning the power off and on again.
(Speaker volume is reduced automatically when the speaker
protection circuit operates).
*When an optional CD/DVD changer is connected through the CeNET cable, this unit can control CD/DVD changer operations.
*If an error display other than the ones described above appears, press the reset button.
CD/MP3/WMA
Water droplets may form on the
internal lens when the car is parked in a
humid place.
File system is not correct.
File name or extension is not correct.
Let dry for about 1 hour with the power on.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
Use alphanumeric/ASCII characters for MP3/WMA file name.
Use ".M3U" for the file extension of a play list.
Sound is bad directly after power
is turned on.
Wrong filename
Play list play is not performed.
Power does not turn on.
(No sound is produced.)
No sound output when operating
the unit with amplifiers or power
antenna attached.
Nothing happens when buttons
are pressed.
Display is not accurate.
No sound heard.
Sound skips or is noisy.
Sound is cut or skipped.
Noise is generated or noise is
mixed with sound.
Fuse is blown.
Incorrect wiring.
Power antenna lead is shorted to
ground or excessive current is required
for remote-on the amplifiers or power
The microprocessor has malfunctioned
due to noise,etc.
DCP or main unit connectors are dirty.
There is a disc other than a compact
disc or foreign matter already in place.
MP3/WMA files are absent in a disc.
Files are not recognized as an
MP3/WMA file.
File system is not correct.
Disc is dirty.
Disc is heavily scratched or warped.
MP3/WMA files are not encoded properly.
Replace with a fuse of the same amperage.
Wire properly.
1. Turn the unit off.
2. Remove all wires attached to the power antenna lead. Check
each wire for a possible short to ground using an ohm meter.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire to the turn off before
power antenna lead one by one. If the amplifiers
all wires are attached, use an external relay to provide
remote-on voltage(excessive current required).
Wipe the dirt off with a soft cloth moistened with cleaning alcohol.
With the slooping console open, press and hold the [
for 3 seconds or longer.The foreign matter is forcibly ejected.
Write MP3/WMA files onto the disc properly.
Use MP3/WMA files encoded properly.
Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
Clean the disc with a soft cloth.
Replace with a disc with no scratches.
Use MP3/WMA files encoded properly.
General
Turn of f the power , then
press the [ RELEASE ]
button and remove the DCP.
Press the reset button with
a thin rod.
Measure
CD/MP3/WMA
Reset button
Problem Cause
antenna.
] button

DXZ945MP
DXZ946MP -4-
ANT
Ce-NET
Q602
IC602
IC302
IE-BUS
DRIVER
CD MECH MODULE
DCP
CD
MECH Q201
ACC 8V
STB
DRIVER
AUX IN
BL1
Q9
IC1
Q7 Q6
ISOLATION
IC501 IC401
IC507 IC509 IC508 IC451
IC452
B/U
ACC
AMP REM POWER ANT PHONE INT ILL
MECH 8V STB
RCA FRONT RCA REAR
RCA 2-ZONE
SP OUT
RCA NON FADER
IC101
Q450 Q452 Q451 Q453 Q454 Q455 Q456 Q457
IC201
Q226 Q231 Q229 Q213 Q212
Q603
IC230
SLOPE
MOTOR
MOTOR
DRIVER
ILL DET
ILL SW
T201
AUDIO
Q222,Q223
IC301
MASTER
IC604
IC606 IC605
VOL
DET
IE-BUS DRIVER
Q201
IC220 IC221
Q230
Q235 Q227
Q210
Q711
Q710
Q701
Q703
IC705
IC700
DCP U-COM
IC702
KEY
MATRIX
IC740
TOUCH PANEL
U-COM
(LCD DRIVER)
IC770
DISPLAY
CONTROLLER
IC762
IC701
CONTRAST
VR700
IR700
Q700
IR
RECEIV.
ROTARY
DIMM
SW
KEY ILL
LCD BACK LIGHT
BLINKING
LED
6V STB
8V STB
DSP 3.3V
AUDIO
BLOCK DIAGRAM
Main section

DXZ945MP
DXZ946MP
-5-
CD mechanism section
MP3&WMA Encoded disc/CD-DA disc
(CD-ROM ISO9660)
CD Mecha.
㵘㵘GS-1 P/U㵘CP-51
J2㵘10pin J1㵘15pin
IC101
DRIVER
3.3V(I/O) 1.6V(Core)
3.3V
FAN8047G3
IC6
IC4 IC9
DSP
LOGIC DRAM
TMS320DA140
SN74䌌䌖C139 K4S641632F-TC60
(CD-ROM I/F)
(1M x 16bit x 4B)
Q1
3.3V
(ECC)
IC7
Transistor IC102
(MPEG audio decode)
LOGIC
5V㸢3.3V CD㵘DSP
(WMA decode)
SN74䌌䌖74
TC94A15F
(CD-DA ESP)
(Digital servo)
IC2 (DF/DAC)
Regulator
3.3V㸢1.6V
3.3V
IC10
IC1
FLASH ROM
LOGIC
MBM29DL800BA
(8Mbit)
AUDIO
D-OUT
IC3
LOGIC
SN74HCT08
V-BUS
I/F-5V
ACC8V
J3 20pin
ACC5V
(TO MAIN UNIT)
DAC SN74䌌䌖C139
SYSTEM CHECK
The first time that this unit is turned on after wire connec-
tions are completed, this unit checks which equipment is
connected. (This is called the "system check.") When the
power is turned ON, and "System Check" is displayed, fol-
low the procedure below to perform the system check.
1. When "System Check" appears on the display, press the
[ROTARY] knob.
The system check starts.
When the system check is complete,"Completed" ap-
pears on the display.
2. Press the [ROTARY] knob again.
The main display for the radio mode appears.
CODEMATIC
This function prevents persons who do not know the touch
sequence from easily operating this unit. The Touch Code
display appears when DCP is attached and the power is
turned ON with "CODEMATIC" set to "ON".
If you touch the display in this screen in the preset order,
"SUCCESSFUL" is displayed and the power is turned OFF.
When the power is next turned ON, the Touch Code display
does not appear, and the main display in the radio mode or
CD mode is displayed.
CONNECTIONS
8MM
MA X
EXTENSION LEAD
1
AUX INPUT
2-ZONE OUTPUT
RED
GRN GRY
(For power amp)
BLK
RCA 4CH OUTPUT
PUR
(For center SP)
(For wireless headphone)
Ce NET
(For CD/DVD auto changer,TV)
16PIN SOCKET
(Power supply)
RCA 2CH OUTPUT
ANTENNA RECEPT.
(For radio antenna) * For details of connections, see "PRINTED
WIRING BOARD"(cf.page 31).

DXZ945MP
DXZ946MP -6-
052-3390-00 M30622MEP-126GP CD/MP3 Master Controller
1.Terminal Description
pin 1: DISP Reset : O : Reset pulse output to Display controller.
pin 2: TIME BASE :IN: Time base pulse input.
pin 3: DISP 5V REM : O : Not in use.
pin 4: EXT AMP REM : O : ON signal output to the power supply sec-
tion.
pin 5: SPEED PULSE :IN: The speed pulse input.
pin 6: BYTE :IN: The data length selection(8bit/16bit).
pin 7: CN VSS :IN: Connect to VSS.
pin 8: DISC/CATS : O : DISC/CATS LED control signal output.
pin 9: NU :IN: Not in use.
pin 10: RESET :IN: Reset signal input.
pin 11: X OUT : O : Crystal connection.
pin 12: VSS : - : Negative supply voltage.
pin 13: X IN :IN: Crystal connection.
pin 14: VCC : - : Positive supply voltage.
pin 15: NU :IN: Not in use.
pin 16: ACC DET :IN: ACC detection signal input.
pin 17: BU DET :IN: Backup detection signal input.
pin 18: KEY INT :IN: Key interrupting signal input.
pin 19: 27pin connect :IN: Connect to 27pin.
pin 20: DSP INIT RST : O : The reset signal output to DSP IC.
pin 21: NU : - : Not in use.
pin 22: BEEP : O : Beep out.
pin 23: DSP RST : O : Reset pulse output to the DSP IC.
pin 24: NU : O : Not in use.
pin 25:DD F SW : O : The frequency control signal output for
DC_DC_Converter.
pin 26: NU :IN: Not in use.
pin 27: IE BUS RX :IN: IE Bus serial data input.
pin 28: IE BUS TX : O : IE Bus serial data output.
pin 29: NU : O : Not in use.
pin 30: NU :IN: Not in use.
pin 31: NU :IN: Not in use.
pin 32: NU : O : Not in use.
pin 33: DSP SO : O : Serial data output to the DSP IC.
pin 34: DSP SI :IN: Serial data input from the DSP IC.
pin 35: DSP CLK : O : The clock pulse output to DSP.
pin 36: DSP RDY :IN: Ready signal input from the DSP IC.
pin 37: DSP RQ : O : Request signal output to the DSP IC.
pin 38: NU :IN: Not in use.
pin 39: NU :IN: Not in use.
pin 40: MP3 SRQ :IN: MP3 request signal input.
pin 41: MP3 CS : O : MP3 chip selection signal output.
pin 42: MP3 WP : O : MP3 wakeup signal output.
pin 43: MP3 RESET : O : MP3 reset signal output.
pin 44: NU :IN: Not in use.
pin 45: PLL SI :IN: Serial data input from the PLL IC.
pin 46: PLL SO : O : Serial data output to the PLL IC.
pin 47: PLL SCK : O : The clock pulse output to the PLL IC.
pin 48: PLL CE : O : The chip enable signal output to the PLL
IC.
pin 49: NU :IN: Not in use.
pin 50: RDS TEST :IN: For test.
pin 51: INIT 2 :IN: The initial setting input.
pin 52: INIT 1 :IN: The initial setting input.
pin 53: ILL DET :IN: Illumination ON signal input.
pin 54: NU : O : Not in use.
pin 55: OPEN POSI :IN: The open position detect signal input.
pin 56: CLOSE POSI :IN: The close position detect signal input.
pin 57: NU : O : Not in use.
pin 58: MOTOR+ : O : The control signal output to the motor.
pin 59: MOTOR- : O : The control signal output to the motor.
pin 60: VCC : - : Positive supply voltage.
pin 61: SUB 0 MUTE : O : 2-zone CD muting selection.
pin 62: VSS : - : Negative supply voltage.
pin 63: MAIN 0 MUTE : O : 2-zone CD muting selection.
pin 64: KEY ILL REM : O : Key illumination ON signal output.
pin 65: ST SD :IN: At receiving the FM station, this port de-
tects the stereo signal. At seeking or scan-
ning, this port detects the station detection
signal.
pin 66: NOISE DCHG : O : RDS noise discharge signal output.
pin 67: MUTE SPD UP : O : Station detection speed up command out-
put for RDS.
pin 68: RDS TEST ST : O : For the test mode.
pin 69: RDS MUTE : O : RDS mute signal output.
pin 70: RDS DATA :IN: RDS serial data input.
pin 71: Spect RST : O : Reset pulse output to spectrum analyzer.
pin 72: Spect RD :IN: Read pulse input from spectrum analyzer.
pin 73: RDS CLK :IN: RDS clock pulse input.
pin 74: E VOL CLK : O : The clock pulse output to the volume IC.
pin 75: E VOL DATA : O : The serial data output to the volume IC.
pin 76: SUB E VOL CK : O : The clock pulse output to Sub volume IC.
pin 77: SUB E VOL DT : O : The serial data output to Sub volume IC.
pin 78: INT AMP REM : O : Internal audio amplifier control.
pin 79: AMP MUTE : O : Muting signal output to the Audio Power
Amplifier.
pin 80: AMP REM DT :IN: Remote controller wire short detection.
pin 81: NAVI MUTE : O : Muting signal output to suppress the noise
without Navigation sound interrupting.
pin 82: LINE SYS MU : O : The system muting command output.
pin 83: NU : O : Not in use.
pin 84: PHONE INT :IN: The telephone interrupt signal input.
pin 85: AUTO ANT : O : Motor antenna control signal output.
pin 86: 5V REM : O : ON signal output to the 5V power supply.
pin 87: NOISE :IN: The noise level for RDS.
pin 88: S METER :IN: The input terminal of internal A/D convert-
er to monitor the radio field strength.
pin 89: KEY A/D :IN: The input terminal of the internal ADC for
key judgement.
pin 90: 2-zone Mute : O : 2-zone muting control.
pin 91: SPAN DATA :IN: The serial data input from the spectrum
analyzer.
pin 92: NU :IN: Not in use.
pin 93: SYS ACC : O : ACC detect signal output.
pin 94: A VSS : - : Analog ground.
pin 95: OFFSET DET :IN: The emergency signal input from the pow-
er IC.
pin 96: VREFI :IN: The reference voltage input.
pin 97: A VCC : - : Positive supply voltage for the internal an-
alog section.
pin 98: MP3 SI :IN: MP3 serial data input.
pin 99: MP3 SO : O : MP3 serial data output.
pin100: MP3 SCK : O : MP3 clock output.
051-6700-00 TMS320DA140PGE160 Digital Signal Processor
1.Terminal Description
pin 1: VSS : - : Negative supply voltage.
pin 2: Memo Addrss 22:O : Control signal output for Memory IC.
pin 3: VSS : - : Negative supply voltage.
pin 4: VDD : - : Positive supply voltage.
pin 5: Memo Addrss 10:O : Address output to Memory IC.
pin 6: C RESET : O : Reset pulse output to CD IC.
pin 7: Memo Addrss 11:O : Address output to Memory IC.
pin 8: Memo Addrss 12:O : Address output to Memory IC.
pin 9: Memo Addrss 13:O : Address output to Memory IC.
pin 10: Memo Addrss 14:O : Address output to Memory IC.
pin 11: Memo Addrss 15:O : Address output to Memory IC.
pin 12: VDD : - : Positive supply voltage.
pin 13: NU :IN: Not in use.
pin 14: VSS : - : Negative supply voltage.
pin 15: VSS : - : Negative supply voltage.
pin 16: VDD : - : Positive supply voltage.
pin 17: NU :IN: Not in use.
pin 18: NU :IN: Not in use.
pin 19: READY :IN: The ready signal input.
pin 20: PS : O : Control signal output for Memory IC.
EXPLANATION OF IC

DXZ945MP
DXZ946MP
-7-
pin 21: NU : O : Not in use.
pin 22: NU : O : Not in use.
pin 23: WRITE ENBL : O : The write enable signal output.
pin 24: M STRB : O : Control signal output for Memory IC.
pin 25: NU : O : Not in use.
pin 26: NU : O : Not in use.
pin 27: LD CONT : O : The loading control signal output.
pin 28: NU : O : Not in use.
pin 29: NU : O : Not in use.
pin 30: NU :IN: Not in use.
pin 31: CS :IN: The chip select command input.
pin 32: NU : - : Not in use.
pin 33: VDD : - : Positive supply voltage.
pin 34: VSS : - : Negative supply voltage.
pin 35: V BUS WUP :IN: V BUS WUP input.
pin 36: C BUS CE/TRB :I/O: Data bus chip enable signal output to CD
IC. Or mechanism sensor signal input.
pin 37: VSS : - : Negative supply voltage.
pin 38: C BUS CK/TRA :I/O: Data bus clock pulse output to CD IC. Or
mechanism sensor signal input.
pin 39: NU :IN: Not in use.
pin 40: VSS : - : Negative supply voltage.
pin 41: C BCK :IN: Bit clock pulse input from CD IC.
pin 42: NU : O : Not in use.
pin 43: C LRCK :IN: LR clock pulse input from CD IC.
pin 44: NU : O : Not in use.
pin 45: C SD :IN: Serial data input from CD IC.
pin 46: NU :IN: Not in use.
pin 47: MS SI :IN: Serial data input from Master Computer.
pin 48: C DAC BCK : O : Bit clock output for the internal DAC of CD
IC.
pin 49: MS SCK :IN: Serial clock input from Master Computer.
pin 50: VSS : - : Negative supply voltage.
pin 51: NU : O : Not in use.
pin 52: VDD : - : Positive supply voltage.
pin 53: C DAC LRCK : O : LR clock output for the internal DAC of CD
IC.
pin 54: MS CS :IN: Chip select input from Master Computer.
pin 55: NU : O : Not in use.
pin 56: VDD : - : Positive supply voltage.
pin 57: VSS : - : Negative supply voltage.
pin 58: C BUS 0 :I/O: Data bus for CD IC.
pin 59: C DAC SD : O : Serial data output for the internal DAC of
CD IC.
pin 60: MS SO : O : Serial data output to Master Computer.
pin 61: NU : O : Not in use.
pin 62: NU :IN: Not in use.
pin 63: NU :IN: Not in use.
pin 64: WUP :IN: V BUS WUP.
pin 65: SBSY :IN: Sub code block synchronous signal detec-
tion input.
pin 66: C BMOVF :IN: Buffer memory over flag input from CD IC.
pin 67: SCK :IN: The clock pulse input.
pin 68: VDD : - : Positive supply voltage.
pin 69: C BUS 1 :I/O: Data bus for CD IC.
pin 70: VSS : - : Negative supply voltage.
pin 71: LIMIT :IN: Inside limit switch signal input for the pick-
up.
pin 72: VSS : - : Negative supply voltage.
pin 73: C PF/ CHUCK :IN: C2 correction data input from CD IC. Or
chucking signal input from the mechanism.
pin 74: LD MUTE : O : Muting signal output to the CD mechanism.
pin 75: VDD : - : Positive supply voltage.
pin 76: VSS : - : Negative supply voltage.
pin 77: Clock Mode 1 :IN: Clock mode selection.
pin 78: Clock Mode 2 :IN: Clock mode selection.
pin 79: Clock Mode 3 :IN: Clock mode selection.
pin 80: NU :IN: Not in use.
pin 81: C BUS 2 :I/O: Data bus for CD IC.
pin 82: NU : O : Not in use.
pin 83: NU :IN: Not in use.
pin 84: NU : O : Not in use.
pin 85: NU : O : Not in use.
pin 86: NU :IN: Not in use.
pin 87: NU :IN: Not in use.
pin 88: NU :IN: Not in use.
pin 89: NU :IN: Not in use.
pin 90: VSS : - : Negative supply voltage.
pin 91: VDD : - : Positive supply voltage.
pin 92: NU :IN: Not in use.
pin 93: VSS : - : Negative supply voltage.
pin 94: CLK OUT : O : Clock pulse output.
pin 95: C BUS 3 :I/O: Data bus for CD IC.
pin 96: NU : O : Not in use.
pin 97: SYS CLK :IN: 16.92MHz
pin 98: RESET :IN: Reset signal input.
pin 99: Memo Data 0 :I/O: Parallel data input/output for Memory IC.
pin100: Memo Data 1 :I/O: Parallel data input/output for Memory IC.
pin101: Memo Data 2 :I/O: Parallel data input/output for Memory IC.
pin102: Memo Data 3 :I/O: Parallel data input/output for Memory IC.
pin103: Memo Data 4 :I/O: Parallel data input/output for Memory IC.
pin104: Memo Data 5 :I/O: Parallel data input/output for Memory IC.
pin105: Memo Addrss 16:O : Address output to Memory IC.
pin106: VSS : - : Negative supply voltage.
pin107: Memo Addrss 17:O : Address output to Memory IC.
pin108: Memo Addrss 18:O : Address output to Memory IC.
pin109: Memo Addrss 19:O : Address output to Memory IC.
pin110: Memo Addrss 20:O : Address output to Memory IC.
pin111: VSS : - : Negative supply voltage.
pin112: VDD : - : Positive supply voltage.
pin113: Memo Data 6 :I/O: Parallel data input/output for Memory IC.
pin114: Memo Data 7 :I/O: Parallel data input/output for Memory IC.
pin115: Memo Data 8 :I/O: Parallel data input/output for Memory IC.
pin116: Memo Data 9 :I/O: Parallel data input/output for Memory IC.
pin117: Memo Data 10 :I/O: Parallel data input/output for Memory IC.
pin118: Memo Data 11 :I/O: Parallel data input/output for Memory IC.
pin119: Memo Data 12 :I/O: Parallel data input/output for Memory IC.
pin120: CN VCC :IN: Connect to VCC.
pin121: Memo Data 13 :I/O: Parallel data input/output for Memory IC.
pin122: Memo Data 14 :I/O: Parallel data input/output for Memory IC.
pin123: Memo Data 15 :I/O: Parallel data input/output for Memory IC.
pin124: SRQ : O : V BUS SRQ output.
pin125: VDD : - : Positive supply voltage.
pin126: VSS : - : Negative supply voltage.
pin127: NU :IN: Not in use.
pin128: VSS : - : Negative supply voltage.
pin129: NU :IN: Not in use.
pin130: VDD : - : Positive supply voltage.
pin131: Memo Addrss 0: O : Address output to Memory IC.
pin132: Memo Addrss 1: O : Address output to Memory IC.
pin133: Memo Addrss 2: O : Address output to Memory IC.
pin134: Memo Addrss 3: O : Address output to Memory IC.
pin135: SYS POWER : O : System power supply control signal output.
pin136: Memo Addrss 4: O : Address output to Memory IC.
pin137: Memo Addrss 5: O : Address output to Memory IC.
pin138: Memo Addrss 6: O : Address output to Memory IC.
pin139: Memo Addrss 7: O : Address output to Memory IC.
pin140: Memo Addrss 8: O : Address output to Memory IC.
pin141: Memo Addrss 9: O : Address output to Memory IC.
pin142: VDD : - : Positive supply voltage.
pin143: Memo Addrss 21:O : Control signal output for Memory IC.
pin144: VSS : - : Negative supply voltage.

DXZ945MP
DXZ946MP -8-
051-6399-00 TC94A15F CD IC
1.Terminal Description
pin 1: IPF OUT : O : IP flag output.
pin 2: SB OK O : O : Sub code Q data CRCC OK signal output.
pin 3: CLOCKIO :I/O: The clock pulse input/output for the sub
code reading.
pin 4: VDD : - : Positive supply voltage.
pin 5: VSS : - : Negative supply voltage.
pin 6: DATA : O : DATA
pin 7: SF SY O : O : Playback frame synchronous signal output.
pin 8: SB SY O : O : Sub code block synchronous signal output.
pin 9: HSO : O : The play speed flag output.
pin 10: UHSO : O : The play speed flag output.
pin 11: AR SEL IN :IN: Fix to the high level.
pin 12: AWRC : O : The control signal output for the active
wide range VCO.
pin 13: P VDD : - : PLL positive supply voltage.
pin 14: PDO : O : Phase difference signal output of EFM-
PLCK.
pin 15: TMAX S : O : T max judgment output.
pin 16: TMAX : O : T max judgment output.
pin 17: LPF N :IN: Inverted input of LPF for PLL.
pin 18: LPF OUT : O : The output terminal for the Low Pass Fil-
ter.
pin 19: P Vref : - : PLL reference voltage.
pin 20: VCO FILTER : O : Loop filter for VCO.
pin 21: VCO Ref :IN: VCO reference voltage input.
pin 22: DTC N : O : For the analog slicer.
pin 23: DTC P : O : For the analog slicer.
pin 24: PLL VSS : - : PLL ground.
pin 25: SLCO : O : Output of internal DAC for data slice level
generation.
pin 26: RF IN :IN: RF signal input.
pin 27: RF RP :IN: RF ripple input.
pin 28: RF EQ OUT : O : The output of the RF equalizer.
pin 29: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 30: RES IN : - : For reference current setting.
pin 31: Vref OUT : O : The reference voltage output.
pin 32: VMDIR : O : The reference voltage output.
pin 33: TESTR : O : The compensation terminal for RFEQO off-
set.
pin 34: INVSEL :IN: MDI polarity selection.
pin 35: AGCI :IN: The input terminal of RF AGC amplifier.
pin 36: RF DCI :IN: The input terminal for RF peak detection.
pin 37: RF OUT : O : RF signal output.
pin 38: PN SEL :IN: The transistor type selection input for laser
diode driver. L=NPN, H=PNP.
pin 39: EQ SET : O : The equalizer setting terminal.
pin 40: RF VDD : - : RF power supply.
pin 41: LDO : O : The laser diode drive output.
pin 42: MDI :IN: Monitor photo diode signal input.
pin 43: RF VSS : - : RF ground.
pin 44: FNI 2 :IN: Main beam signal input.
pin 45: FNI 1 :IN: Main beam signal input.
pin 46: FPI 2 :IN: Main beam signal input.
pin 47: FPI 1 :IN: Main beam signal input.
pin 48: TPI :IN: Sub beam signal input.
pin 49: TNI :IN: Sub beam signal input.
pin 50: FTEO : O : For test.
pin 51: RF ZI :IN: RF ripple zero cross signal input.
pin 52: A VSS : - : Analog ground.
pin 53: RF RP : O : RF ripple signal output.
pin 54: RF DC : O : RF peak detection signal output. (hologram
suitable)
pin 55: FEI : O : Focus error signal output.
pin 56: SBAD : O : Sub beam add signal output.
pin 57: TEI : O : Tracking error signal output.
pin 58: TE Z IN :IN: Tracking error signal inpur for zero cross.
pin 59: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 60: FOO : O : Focus equalizer output.
pin 61: TRO : O : Tracking equalizer output.
pin 62: Vref : O : Reference voltage output.
pin 63: FMO : O : Field equalizer output / Speed error output.
pin 64: DMO : O : Disk equalizer output.
pin 65: IO2A :I/O: General input/output.
pin 66: IO3A :I/O: General input/output.
pin 67: MONIT : O : Internal DSP signal monitor.
pin 68: FG IN :IN: FG input for the spindle CAV servo.
pin 69: VSS : - : Negative supply voltage.
pin 70: VDD : - : Positive supply voltage.
pin 71: TESIN :IN: For test.
pin 72: X VSS : - : Master clock analog ground.
pin 73: X IN :IN: Crystal connection.
pin 74: X O : O : Crystal connection.
pin 75: X VDD : - : Clock power supply.
pin 76: D VSS : - : Digital ground.
pin 77: RO : O : Right channel data output for 1-bit DAC.
pin 78: D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 79: D Vref : O : Digital reference voltage.
pin 80: LO : O : Left channel data output for 1-bit DAC.
pin 81: D VSS : - : Digital ground.
pin 82: Z DET O : O : 1bit DAC zero flag output.
pin 83: VSS : - : Negative supply voltage.
pin 84: BUS 0 :I/O: CD IC Data input / output.
pin 85: BUS 1 :I/O: CD IC Data input / output.
pin 86: BUS 2 :I/O: CD IC Data input / output.
pin 87: BUS 3 :I/O: CD IC Data input / output.
pin 88: BU CK IN :IN: CD IC Data clock input.
pin 89: CCEI :IN: Chip enable input.
pin 90: RSTI :IN: Reset signal input.
pin 91: VDD : - : Positive supply voltage.
pin 92: EMPHI/FAO :I/O: Emphasis input for 1-bit DAC / Flag A
output.
pin 93: BCKI/FBO :I/O: Bit clock input for 1-bit DAC / Flag B out-
put.
pin 94: AIN/FCO :I/O: Audio input for 1-bit DAC / Flag C output.
pin 95: LRCKI/FDO :I/O: LR clock input for 1-bit DAC / Flag D out-
put.
pin 96: EMPHO : O : Emphasis flag output. H=Emphasis ON.
pin 97: B CK O : O : Bit clock output.
pin 98: A OUT : O : Audio signal output.
pin 99: LR CK O : O : LR clock output.
pin100: D OUT : O : Serial data output.
051-0350-91 NJM2904M Dual Operational Amplifier
1 2 3 4VEE
VCC 8
7 6 5

DXZ945MP
DXZ946MP
-9-
052-7068-00 M30626MHP-142GP Display Controller
1.Terminal Description
pin 1: NU :IN: Not in use.
pin 2: CONT CONT : O : LCD contrast control voltage output.
pin 3: DISP 5V REM : O : The power supply circuit control signal out-
put.
pin 4: LCD REM : O : On signal output for LCD power supply.
pin 5: REMOCON :IN: Remote controller signal input terminal.
pin 6: BYTE :IN: The data length selection(8bit/16bit).
pin 7: CN VSS :IN: Connect to VSS.
pin 8: NU :IN: Not in use.
pin 9: NU :IN: Not in use.
pin 10: RESET :IN: Reset signal input.
pin 11: X OUT : O : Crystal connection.
pin 12: VSS : - : Negative supply voltage.
pin 13: X IN :IN: Crystal connection.
pin 14: VCC : - : Positive supply voltage.
pin 15: NU :IN: Not in use.
pin 16: ACC DET :IN: ACC detection signal input.
pin 17: NU :IN: Not in use.
pin 18: ILL DET :IN: Illumination ON signal input.
pin 19: 27pin connect :IN: Connect to 27pin.
pin 20: LCD RESET : O : Reset pulse output to LCD.
pin 21: JOG CW :IN: Jog key signal input.
pin 22: JOG CCW :IN: Jog key signal input.
pin 23: NU : O : Not in use.
pin 24: PULSE DIMM : O : Dimmer pulse output for LCD back light.
pin 25: NU :IN: Not in use.
pin 26: NU :IN: Not in use.
pin 27: IE BUS RX :IN: IE Bus serial data input.
pin 28: IE BUS TX : O : IE Bus serial data output.
pin 29: NU : O : Not in use.
pin 30: NU :IN: Not in use.
pin 31: NU :IN: Not in use.
pin 32: NU : O : Not in use.
pin 33: TP TX : O : Touch Panel Controller communication line.
pin 34: TP RX : O : Touch Panel Controller communication line.
pin 35: TP REQ :IN: The request signal from the touch panel
micro computer.
pin 36: DATA/COMMAN : O : Data/Command flag output to the LCD driv-
er.
pin 37: NU : - : Not in use.
pin 38: NU :IN: Not in use.
pin 39: NU :IN: Not in use.
pin 40: NU :IN: Not in use.
pin 41: NU :IN: Not in use.
pin 42: LCD RD : O : Read command output to LCD.
pin 43: NU :IN: Not in use.
pin 44: LCD WR : O : Write command output to LCD.
pin 45: NU : O : Not in use.
pin 46: A20 LCD CS1 : O : The chip select signal output.
pin 47: F ROM Add 19: O : F ROM Address output.
pin 48: F ROM CE : O : Fixed to the low level in the normal condi-
tion.
pin 49: F ROM Add 18: O : F ROM Address output.
pin 50: NU : O : Not in use.
pin 51: F ROM Add 17: O : F ROM Address output.
pin 52: F ROM Add 16: O : F ROM Address output.
pin 53: F ROM Add 15: O : F ROM Address output.
pin 54: F ROM Add 14: O : F ROM Address output.
pin 55: F ROM Add 13: O : F ROM Address output.
pin 56: F ROM Add 12: O : F ROM Address output.
pin 57: F ROM Add 11: O : F ROM Address output.
pin 58: F ROM Add 10: O : F ROM Address output.
pin 59: F ROM Add 9 : O : F ROM Address output.
pin 60: VCC : - : Positive supply voltage.
pin 61: F ROM Add 8 : O : F ROM Address output.
pin 62: VSS : - : Negative supply voltage.
pin 63: F ROM Add 7 : O : F ROM Address output.
pin 64: F ROM Add 6 : O : F ROM Address output.
pin 65:F ROM Add 5 : O : F ROM Address output.
pin 66:F ROM Add 4 : O : F ROM Address output.
pin 67:F ROM Add 3 : O : F ROM Address output.
pin 68:F ROM Add 2 : O : F ROM Address output.
pin 69:F ROM Add 1 : O : F ROM Address output.
pin 70:F ROM Add 0 : O : F ROM Address output.
pin 71: NU :IN: Not in use.
pin 72: NU :IN: Not in use.
pin 73: NU :IN: Not in use.
pin 74: NU :IN: Not in use.
pin 75: NU :IN: Not in use.
pin 76: NU :IN: Not in use.
pin 77: NU :IN: Not in use.
pin 78: NU :IN: Not in use.
pin 79: F ROM Data 7 :I/O: F ROM Data input/output.
pin 80: F ROM Data 6 :I/O: F ROM Data input/output.
pin 81: F ROM Data 5 :I/O: F ROM Data input/output.
pin 82: F ROM Data 4 :I/O: F ROM Data input/output.
pin 83: F ROM Data 3 :I/O: F ROM Data input/output.
pin 84: F ROM Data 2 :I/O: F ROM Data input/output.
pin 85: F ROM Data 1 :I/O: F ROM Data input/output.
pin 86: F ROM Data 0 :I/O: F ROM Data input/output.
pin 87: NU :IN: Not in use.
pin 88: NU :IN: Not in use.
pin 89: NU :IN: Not in use.
pin 90: NU :IN: Not in use.
pin 91: NU :IN: Not in use.
pin 92: DISP OFF : O : The display OFF signal output.
pin 93: NU :IN: Not in use.
pin 94: A VSS : - : Analog ground.
pin 95: AUT DIMM :IN: The automatic dimmer signal input.
pin 96: VREFI :IN: The reference voltage input.
pin 97: A VCC : - : Positive supply voltage for the internal an-
alog section.
pin 98: NU :IN: Not in use.
pin 99: NU :IN: Not in use.
pin100: NU :IN: Not in use.
051-7201-08 TC7W00F Dual 2-inputs NAND Gate
1
2
3
4
8
7
6
5
VCC
GND
16 15 14 13 12
11
10
9
1 2 3 4 5 6 7 8GND
NC
NC
VCC
051-7285-08 CD74HC4050PWR Hex Buffer

DXZ945MP
DXZ946MP -10-
051-6074-00 GMFC-01-5VA STN LCD Controller
1.Terminal Description
pin 1: VDD : - : Positive supply voltage.
pin 2: NU : - : Not in use.
pin 3: NU : - : Not in use.
pin 4: 68_80X :IN: MPU interface setting.
pin 5: ECKL :IN: The clock selection.
pin 6: DIV 0 :IN: Clock dividing setting.
pin 7: DIV 1 :IN: Clock dividing setting.
pin 8: CKL IN :IN: External clock pulse input.
pin 9: NU : - : Not in use.
pin 10: VDD : - : Positive supply voltage.
pin 11: GND : - : Ground.
pin 12: X OUT : O : Crystal connection.
pin 13: X IN :IN: Crystal connection.
pin 14: VDD : - : Positive supply voltage.
pin 15: GND : - : Ground.
pin 16: NU : - : Not in use.
pin 17: NU : - : Not in use.
pin 18: NU : - : Not in use.
pin 19: NU : - : Not in use.
pin 20: NU : - : Not in use.
pin 21: NU : - : Not in use.
pin 22: NU : - : Not in use.
pin 23: NU : - : Not in use.
pin 24: NU : - : Not in use.
pin 25: VDD : - : Positive supply voltage.
pin 26: GND : - : Ground.
pin 27: CHIP SEL : O : The chip select signal output.
pin 28: CEO : O : Chip enable output.
pin 29: WRITE ENBL : O : The write enable signal output.
pin 30: GND : - : Ground.
pin 31: I/O 1 :I/O: Data input/output.
pin 32: I/O 2 :I/O: Data input/output.
pin 33: I/O 3 :I/O: Data input/output.
pin 34: I/O 4 :I/O: Data input/output.
pin 35: I/O 5 :I/O: Data input/output.
pin 36: I/O 6 :I/O: Data input/output.
pin 37: I/O 7 :I/O: Data input/output.
pin 38: I/O 8 :I/O: Data input/output.
pin 39: VDD : - : Positive supply voltage.
pin 40: HA 0 : O : Host address bus.
pin 41: HA 1 : O : Host address bus.
pin 42: HA 2 : O : Host address bus.
pin 43: HA 3 : O : Host address bus.
pin 44: HA 4 : O : Host address bus.
pin 45: HA 5 : O : Host address bus.
pin 46: HA 6 : O : Host address bus.
pin 47: HA 7 : O : Host address bus.
pin 48: HA 8 : O : Host address bus.
pin 49: NU : - : Not in use.
pin 50: GND : - : Ground.
pin 51: VDD : - : Positive supply voltage.
pin 52: VA 0 : O : Address bus.
pin 53: VA 1 : O : Address bus.
pin 54: VA 2 : O : Address bus.
pin 55: VA 3 : O : Address bus.
pin 56: VA 4 : O : Address bus.
pin 57: VA 5 : O : Address bus.
pin 58: VA 6 : O : Address bus.
pin 59: VA 7 : O : Address bus.
pin 60: VA 8 : O : Address bus.
pin 61: VA 9 : O : Address bus.
pin 62: GND : - : Ground.
pin 63: M4 : O : The pulse output to change drive-signal to
AC.
pin 64: VDD : - : Positive supply voltage.
pin 65: M16 : O : The pulse output to change drive-signal to
AC.
pin 66: FLM : O : Start pulse output for the common.
pin 67: M : O : The pulse output to change drive-signal to
AC.
pin 68: CL 1 C : O : Shift clock output for the common.
pin 69: CL 1 S : O : Shift clock output for the segment.
pin 70: CL 2 : O : Data clock output for the segment.
pin 71: LCD 0 : O : Data pulse output for the segment.
pin 72: LCD 1 : O : Data pulse output for the segment.
pin 73: LCD 2 : O : Data pulse output for the segment.
pin 74: LCD 3 : O : Data pulse output for the segment.
pin 75: VDD : - : Positive supply voltage.
pin 76: GND : - : Ground.
pin 77: NU : - : Not in use.
pin 78: NU : - : Not in use.
pin 79: NU : - : Not in use.
pin 80: NU : - : Not in use.
pin 81: NU : - : Not in use.
pin 82: NU : - : Not in use.
pin 83: NU : - : Not in use.
pin 84: NU : - : Not in use.
pin 85: CS 1 :IN: The chip select command input.
pin 86: VDD : - : Positive supply voltage.
pin 87: RESET :IN: Reset signal input.
pin 88: RDI(E) :IN: Read command input.(Enable clock input.)
pin 89: WRITE(W/R) :IN: Write control signal input.(Read control sig-
nal input.)
pin 90: A 0 :IN: The data flag input.
pin 91: GND : - : Ground.
pin 92: D 0 :I/O: The data signal input/output.
pin 93: D 1 :I/O: The data signal input/output.
pin 94: D 2 :I/O: The data signal input/output.
pin 95: D 3 :I/O: The data signal input/output.
pin 96: D 4 :I/O: The data signal input/output.
pin 97: D 5 :I/O: The data signal input/output.
pin 98: D 6 :I/O: The data signal input/output.
pin 99: D 7 :I/O: The data signal input/output.
pin100: GND : - : Ground.
051-5441-08 BD4828G-TR Precision Vlotage Detector 2.8V
Terminal description
pin 1: OUTPUT : N channel open drain output, positive logic.
pin 2: VDD : Positive supply voltage.
pin 3: GND : Ground.
pin 4: NC : Not in use.
pin 5: NC : Not in use.
1
2
3
5
4
N.C.
N.C.
OUTPUT
VDD
GND
051-5836-90 NJU7507
Band Pass Filter for Audio Spectrum Analyzer Display
1.Terminal Description
pin 1: OSC 1 : External resistor connection.
pin 2: OSC 2 : External resistor connection or External clock
pulse input.
pin 3: RST_/CKO : Reset signal input and 2/3 clock pulse out-
put.
pin 4: RD : Trigger pulse output for reading-out the VOUT
of each band.
pin 5: VSS : Ground.
pin 6: V OUT : Peak voltage of each band output.
pin 7: A IN : Audio signal input.
pin 8: VDD : Positive power supply.

DXZ945MP
DXZ946MP
-11-
051-6705-00 AK7720A Audio DSP with 2ch ADC and 6ch DAC
1.Terminal Description
pin 1: LFLT :IN: The capacitor and the resistor connection
terminal for PLL.
pin 2: A VSS : - : Analog ground.
pin 3: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 4: INIT RESET :IN: The initial reset input.
pin 5: CODEC RESET :IN: The CODEC reset input.
pin 6: DSP RESET :IN: DSP reset input.
pin 7: S MUTE :IN: The soft muting command input.
pin 8: B VSS : - : Ground for the bus interface section.
pin 9: PLL :IN: Open or Connect to DVSS usually.
pin 10: CKS :IN: The clock pulse selection.
pin 11: S Data in A :IN: DSP serial data input. Open or connect to
DVSS usually.
pin 12: S Data in 1 :IN: DSP serial data input.
pin 13: S Data in 2 :IN: DSP serial data input.
pin 14: S Data out 1 : O : DSP serial data output.
pin 15: S Data out 2 : O : DSP serial data output.
pin 16: S Data out 3/AD: O : DSP/ADC serial data output.
pin 17: S D OUT : O : The serial data output.
pin 18:LR CK I/O :I/O:SMODE(pin20) = L : 1fs clock input.
SMODE(pin20) = H : 1fs clock output.
pin 19: BIT CLK :I/O: SMODE(pin20) = L : 64fs clock input.
SMODE(pin20) = H : 64fs clock output.
pin 20: S MODE :IN: Slave master selection.
pin 21: Clock Out : O : Clock Out.
pin 22: D VSS : - : Digital ground.
pin 23: D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 24: XT I :IN: Oscillation terminal.
pin 25: XT O : O : Oscillation terminal.
pin 26: JX :IN: External jumping signal input.
pin 27: RQ :IN: The request signal input from the master
side.
pin 28: S CLK :IN: Sift clock input.
pin 29: SI :IN: Serial data input.
pin 30: SO : O : Serial data output.
pin 31: Write Ready : O : Write ready flag output.
pin 32: Data Ready : O : Data output ready flag output.
pin 33:CAS :O :The column address strobe output to
DRAM.
pin 34: RAS : O : The row address strobe output to DRAM.
pin 35: WRITE ENBL : O : The write enable signal output.
pin 36: D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 37: D VSS : - : Digital ground.
pin 38: A 0 : O : Address signal output.
pin 39: A 1 : O : Address signal output.
pin 40: A 2 : O : Address signal output.
pin 41: A 3 : O : Address signal output.
pin 42: A 4 : O : Address signal output.
pin 43: A 5 : O : Address signal output.
pin 44: A 6 : O : Address signal output.
pin 45: A 7 : O : Address signal output.
pin 46: A 8 : O : Address signal output.
pin 47: A 9 : O : Address signal output.
pin 48: A 10 : O : Address output to the external DRAM.
pin 49: A 11 : O : Address output to the external DRAM.
pin 50: A 12 : O : Address signal output.
pin 51: A 13 : O : Address signal output.
pin 52: A 14 : O : Address signal output.
pin 53: A 15 : O : Address signal output.
pin 54: A 16 : O : Address signal output.
pin 55: D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 56: D VSS : - : Digital ground.
pin 57: OUT ENABLE : O : The output enable command output.
pin 58: I/O 0 :I/O: Data input/output.
pin 59: I/O 1 :I/O: Data input/output.
pin 60: I/O 2 :I/O: Data input/output.
pin 61: I/O 3 :I/O: Data input/output.
pin 62: I/O 4 :I/O: Data input/output.
pin 63: I/O 5 :I/O: Data input/output.
pin 64: I/O 6 :I/O: Data input/output.
pin 65: I/O 7 :I/O: Data input/output.
pin 66: D VDD : - : Positive supply voltage for the digital sec-
tion.
pin 67: D VSS : - : Digital ground.
pin 68: TEST : - : For the Test.
pin 69: TEST : - : For the Test.
pin 70: B VSS : - : Ground.
pin 71: A OUT 3 R- : O : Inverted Right channel audio signal output
of DAC-3.
pin 72: A OUT 3 R+ : O : Non-inverted Right channel audio signal
output of DAC-3.
pin 73: NU : - : Not in use.
pin 74: A OUT 3 L- : O : Inverted Left channel audio signal output of
DAC-3.
pin 75: A OUT 3 L+ : O : Non-inverted Left channel audio signal out-
put of DAC-3.
pin 76: A OUT 2 R- : O : Inverted Right channel audio signal output
of DAC-2.
pin 77: A OUT 2 R+ : O : Non-inverted Right channel audio signal
output of DAC-2.
pin 78: NU : - : Not in use.
pin 79: A OUT 2 L- : O : Inverted Left channel audio signal output of
DAC-2.
pin 80: A OUT 2 L+ : O : Non-inverted Left channel audio signal out-
put of DAC-2.
pin 81: NU : - : Not in use.
pin 82: A OUT 1 R- : O : Inverted Right channel audio signal output
of DAC-1.
pin 83: A OUT 1 R+ : O : Non-inverted Right channel audio signal
output of DAC-1.
pin 84: NU : - : Not in use.
pin 85: A OUT 1 L- : O : Inverted Left channel audio signal output of
DAC-1.
pin 86: A OUT 1 L+ : O : Non-inverted Left channel audio signal out-
put of DAC-1.
pin 87: Vr DAC Low :IN: The reference voltage input.
pin 88: A VSS : - : Analog ground.
pin 89: A VSS : - : Analog ground.
pin 90: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 91: Vr DAC High :IN: The reference voltage input.
pin 92: NU : - : Not in use.
pin 93: Vr ADC Low :IN: The reference voltage input.
pin 94: A VSS : - : Analog ground.
pin 95: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 96: Vr ADC High :IN: The reference voltage input.
pin 97: A IN R- :IN: Inverted Right channel audio signal input.
pin 98: A IN R+ :IN: Non-inverted Right channel audio signal in-
put.
pin 99: A IN L- :IN: Inverted Left channel audio signal input.
pin100: A IN L+ :IN: Non-inverted Left channel audio signal in-
put.

DXZ945MP
DXZ946MP -12-
052-7066-00 M30102M2-557FP Touch Panel Controller
1.Terminal Description
pin 1: REQUEST : O : The request signal output.
pin 2: S DATA IN :IN: The serial data input.
pin 3: NU : O : Not in use.
pin 4: CN VSS :IN: Connect to VSS.
pin 5: NU : O : Not in use.
pin 6: NU : O : Not in use.
pin 7: RESET :IN: Reset signal input.
pin 8: X OUT : O : Crystal connection.
pin 9: VSS : - : Negative supply voltage.
pin 10: X IN :IN: Crystal connection.
pin 11: VCC : - : Positive supply voltage.
pin 12: NU : O : Not in use.
pin 13: NU :IN: Not in use.
pin 14: NU :IN: Not in use.
pin 15: NU : O : Not in use.
pin 16: Key I 3 :IN:Key scan signal input.
pin 17: Key O 2 : O : Key scan output terminal.
pin 18: NU : - : Not in use.
pin 19: Key O 1 : O : Key scan output terminal.
pin 20: Key I 2 :IN:Key scan signal input.
pin 21: Key I 1 :IN:Key scan signal input.
pin 22: Key I 0 :IN:Key scan signal input.
pin 23: Key O 0 : O : Key scan output terminal.
pin 24: NU : O : Not in use.
pin 25: NU : O : Not in use.
pin 26: NU : O : Not in use.
pin 27: NU : O : Not in use.
pin 28: TPW :IN: Touch panel wake input.
pin 29: PA : O : Connect to pin 28 by a resistor.
pin 30: CHK : O : The touch panel control output.
pin 31: VCC : - : Positive supply voltage.
pin 32: NU : O : Not in use.
pin 33: VSS : - : Negative supply voltage.
pin 34: NU : O : Not in use.
pin 35: IVCC : - : Smoothing capacitor connection.
pin 36: Y R IN :IN: Touch panel co-ordinates input.
pin 37: X R IN :IN: Touch panel co-ordinates input.
pin 38: Y G IN :IN: Touch panel co-ordinates input.
pin 39: X G IN :IN: Touch panel co-ordinates input.
pin 40: VREFI :IN: The reference voltage input.
pin 41: NU : - : Not in use.
pin 42: NU : - : Not in use.
pin 43: NU : - : Not in use.
pin 44: Y+ : O : Touch panel co-ordinates output.
pin 45: X+ : O : Touch panel co-ordinates output.
pin 46: Y- : O : Touch panel co-ordinates output.
pin 47: X- : O : Touch panel co-ordinates output.
pin 48: S DATA O : O : The serial data output.
051-3921-90 MD1423N DC to DC Converter
Terminal Description
pin 1: SS : - : Connect a capacitor for soft start.
pin 2: OCL- :IN: Over current detection.
pin 3: OCL+ :IN: Over current detection.
pin 4: GND : - : Signal ground.
pin 5: R/C :IN: Remote control signal input.
pin 6: VCC : - : Power supply terminal for control section.
pin 7: N.C. : - : No connection.
pin 8: V BOOT : - : High side drive supply for main MOS-FET.
pin 9: V GL : - : The gate terminal of the low side MOS-
FET.
pin 10: N.C. : - : No connection.
pin 11: V OUT : O : Power stage output terminal.
pin 12: V OUT : O : Power stage output terminal.
pin 13: V OUT : O : Power stage output terminal.
pin 14: V OUT : O : Power stage output terminal.
pin 15: N.C. : - : No connection.
pin 16: P GND : - : Power ground.
pin 17: N.C. : - : No connection.
pin 18: VDD : - : Power supply for the power stage.
pin 19: VDD : - : Power supply for the power stage.
pin 20: VDD : - : Power supply for the power stage.
pin 21: VDD : - : Power supply for the power stage.
pin 22: N.C. : - : No connection.
pin 23: V GH : - : The gate terminal of the high side MOS-
FET.
pin 24: N.C. : - : No connection.
pin 25: V B : - : Terminal for bootstrap. Bootstrap capacitor
between VB and VOUT. Supply for high
side circuit.
pin 26: GND : - : Signal ground.
pin 27: OSC : - : The resistor connection to set the frequen-
cy of oscillation.
pin 28: Vref : - : The reference voltage output terminal.
pin 29: N.C. : - : No connection.
pin 30: AMP OUT : O : The output terminal of the internal OP
amp.
pin 31: N.C. : - : No connection.
pin 32: AMP - :IN: The inverted input terminal of the internal
OP amp.
32
2.45V
OSC
2730
S
R
Q
123
AMP-
AMP OUT
OSC
Soft Start
OCL-
OCL+
Low
side
driver
High
side
driver
5.5V
4,26
16
9
GND
V GL
P GND
23
V GH
18,19,20,21
VDD
28
Vref
Bandgap
reference
5.0V
UVLO BOOTON/OFF5R/C
6 8
VCC V BOOT
High
Side
25
V B
11,12,13,14
V OUT

DXZ945MP
DXZ946MP
-13-
052-5055-00 MBM29DL800BA-90PFTN 8 M bit Flash Memory
1. Terminal Description
pin 1: Address 15 :IN: Address signal input.
pin 2: Address 14 :IN: Address signal input.
pin 3: Address 13 :IN: Address signal input.
pin 4: Address 12 :IN: Address signal input.
pin 5: Address 11 :IN: Address signal input.
pin 6: Address 10 :IN: Address signal input.
pin 7: Address 9 :IN: Address signal input.
pin 8: Address 8 :IN: Address signal input.
pin 9: NU : - : Not in use.
pin 10: NU : - : Not in use.
pin 11: WE :IN: Write enable signal input.
pin 12: RESET :IN: Reset signal input.
pin 13: NU : - : Not in use.
pin 14: NU : - : Not in use.
pin 15: Ready/Busy : O : Ready/Busy flag output, H = Ready.
pin 16: Address 18 :IN: Address signal input.
pin 17: Address 17 :IN: Address signal input.
pin 18: Address 7 :IN: Address signal input.
pin 19: Address 6 :IN: Address signal input.
pin 20: Address 5 :IN: Address signal input.
pin 21: Address 4 :IN: Address signal input.
pin 22: Address 3 :IN: Address signal input.
pin 23: Address 2 :IN: Address signal input.
pin 24: Address 1 :IN: Address signal input.
pin 25: Address 0 :IN: Address signal input.
pin 26: CE :IN: Chip enable signal input.
pin 27: VSS : - : Negative supply voltage.
pin 28: OE :IN: Output enable signal input.
pin 29: DQ 0 :I/O: The data input / output.
pin 30: DQ 8 :I/O: The data input / output.
pin 31: DQ 1 :I/O: The data input / output.
pin 32: DQ 9 :I/O: The data input / output.
pin 33: DQ 2 :I/O: The data input / output.
pin 34: DQ 10 :I/O: The data input / output.
pin 35: DQ 3 :I/O: The data input / output.
pin 36: DQ 11 :I/O: The data input / output.
pin 37: VCC : - : Positive supply voltage.
pin 38: DQ 4 :I/O: The data input / output.
pin 39: DQ 12 :I/O: The data input / output.
pin 40: DQ 5 :I/O: The data input / output.
pin 41: DQ 13 :I/O: The data input / output.
pin 42: DQ 6 :I/O: The data input / output.
pin 43: DQ 14 :I/O: The data input / output.
pin 44: DQ 7 :I/O: The data input / output.
pin 45: DQ 15/A-1 :I/O: The data input/output, The Address signal
input.
pin 46: VSS : - : Negative supply voltage.
pin 47: BYTE :IN: The data length selection(8bit/16bit).
pin 48: Address 16 :IN: Address signal input.
052-7067-00 MBM29F016A-90PFTN 16M bit Memory
1.Terminal Description
pin 1: NU : - : Not in use.
pin 2: NU : - : Not in use.
pin 3: A 19 :IN: Address input.
pin 4: A 18 :IN: Address input.
pin 5: A 17 :IN: Address input.
pin 6: A 16 :IN: Address input.
pin 7: A 15 :IN: Address input.
pin 8: A 14 :IN: Address input.
pin 9: A 13 :IN: Address input.
pin 10: A 12 :IN: Address input.
pin 11: CE_ :IN: Chip enable signal input. Negative logic.
pin 12: VCC : - : Positive supply voltage.
pin 13: NU : - : Not in use.
pin 14: RESET_ :IN: Reset signal input. Negative logic.
pin 15: A 11 :IN: Address input.
pin 16: A 10 :IN: Address input.
pin 17: A 9 :IN: Address input.
pin 18: A 8 :IN: Address input.
pin 19: A 7 :IN: Address input.
pin 20: A 6 :IN: Address input.
pin 21: A 5 :IN: Address input.
pin 22: A 4 :IN: Address input.
pin 23: NU : - : Not in use.
pin 24: NU : - : Not in use.
pin 25: NU : - : Not in use.
pin 26: NU : - : Not in use.
pin 27: A 3 :IN: Address input.
pin 28: A 2 :IN: Address input.
pin 29: A 1 :IN: Address input.
pin 30: A 0 :IN: Address input.
pin 31: DQ 0 :I/O: Data input / output.
pin 32: DQ 1 :I/O: Data input / output.
pin 33: DQ 2 :I/O: Data input / output.
pin 34: DQ 3 :I/O: Data input / output.
pin 35: VSS : - : Negative supply voltage.
pin 36: VSS : - : Negative supply voltage.
pin 37: VCC : - : Positive supply voltage.
pin 38: DQ 4 :I/O: Data input / output.
pin 39: DQ 5 :I/O: Data input / output.
pin 40: DQ 6 :I/O: Data input / output.
pin 41: DQ 7 :I/O: Data input / output.
pin 42: RY/BY_ : O : Ready / Busy_
pin 43: OE_ :IN: Output enable signal input. Negative logic.
pin 44: WE_ :IN: Wright enable signal input terminal. Nega-
tive logic.
pin 45: NU : - : Not in use.
pin 46: A 20 :IN: Address input.
pin 47: NU : - : Not in use.
pin 48: NU : - : Not in use.

DXZ945MP
DXZ946MP -14-
G OUT FL V IN FL G OUT FR V IN FR TN FR TN FL BNF 1R BNF 2R BNF 1L BNF 2L GND OUT FR GND OUT FL
42 41 40 39 38 37 36 35 34 33 32 31 30 29
GND
OUT SW
GND
OUT SR
GND
OUT SL
GND
OUT C
GND
OUT SB
VCC
GND
VEE
VDD
28
27
26
25
24
23
22
21
20
19
18
17
16
15
IN FR A
IN FL A
IN SW A
IN SR A
IN SL A
IN C A
IN SB A
IN FR B
IN FL B
IN SW B
IN SR B
IN SL B
IN C B
IN SB B
43
44
45
46
47
48
49
50
51
52
53
54
55
56
GND
G OUT SW
V IN SW
G OUT SR
V IN SR
G OUT SL
V IN SL
G OUT C
V IN C
GND
PORT A
PORT B
DATA
CLOCK
1 2 3 4 5 6 7 8 9
10
11
12 13 14
TONE
Swiches
Logic
051-9109-40 BS62LV256TI-70 32K x 8 bit Static RAM
1.Terminal Description
pin 1: OE :IN: Output enable signal input.
pin 2: A 11 :IN: Address signal input.
pin 3: A 9 :IN: Address signal input.
pin 4: A 8 :IN: Address signal input.
pin 5: A 13 :IN: Address signal input.
pin 6: WE :IN: Write enable signal input.
pin 7: VCC : - : Positive supply voltage.
pin 8: A 14 :IN: Address signal input.
pin 9: A 12 :IN: Address signal input.
pin 10: A 7 :IN: Address signal input.
pin 11: A 6 :IN: Address signal input.
pin 12: A 5 :IN: Address signal input.
pin 13: A 4 :IN: Address signal input.
pin 14: A 3 :IN: Address signal input.
pin 15: A 2 :IN: Address signal input.
pin 16: A 1 :IN: Address signal input.
pin 17: A 0 :IN: Address signal input.
pin 18: DQ 0 :I/O: Data signal input/output.
pin 19: DQ 1 :I/O: Data signal input/output.
pin 20: DQ 2 :I/O: Data signal input/output.
pin 21: GND : - : Ground.
pin 22: DQ 3 :I/O: Data signal input/output.
pin 23: DQ 4 :I/O: Data signal input/output.
pin 24: DQ 5 :I/O: Data signal input/output.
pin 25: DQ 6 :I/O: Data signal input/output.
pin 26: DQ 7 :I/O: Data signal input/output.
pin 27: CE :IN: Chip enable signal input.
pin 28: A 10 :IN: Address signal input.
051-6069-08 FAN8047G3 4 channel Motor Driver
Function Table
SW45 Mute1,2_ Mute 3_ Mute 4_ 1 ch 2 ch 3 ch 4 ch
in in in in out out out out
(pin 28) (pin 9) (pin 27) (pin 20) (pin13,14) (pin11,12) (pin17,18) (pin15,16)
H H H x ON ON ON ON A
H H L x ON ON OFF ON A
H L H x OFF OFF ON OFF
H L L x OFF OFF OFF OFF
L x x H OFF OFF OFF ON B
L x x L OFF OFF OFF OFF
1 2 3 4 5 6 7 8 9
10
11
12 13 14
Level
Shift
Level
Shift
28 27 26 25 24 23 22 21 20 19 18 17 16 15
Level
Shift
Level
Shift
Vref 1 1 ch in 2 ch in Reg on(H) Reg feed Reg out Ground P Vcc 1 Mute 1,2_ Ground 2 ch out - 2 ch out + 1 ch out - 1 ch out +
SW 45 Mute 3_ 4 ch in B Vref 2 4 ch in A 3 ch in S Vcc P Vcc Mute 4_ Ground 3 ch out- 3 ch out+ 4 ch out- 4 ch out+
Regulator
051-2053-00 LA47508 Four Bridge Channels Power Amplifier
1.Terminal Description
pin 1 : NU : Not in use.
pin 2: PWR GND 2 : Power ground terminal 2.
pin 3 : OUT 2- : Inverted power output terminal 2.
pin 4 : STANDBY : Standby signal input terminal.
pin 5 : OUT 2+ : Non inverted power output terminal 2.
pin 6 : VCC : Positive supply voltage.
pin 7 : OUT 1- : Inverted power output terminal 1.
pin 8: PWR GND 1 : Power ground terminal 1.
pin 9 : OUT 1+ : Non inverted power output terminal 1.
pin 10: R.Fil. : Connect the capacitor.
pin 11: IN 1 : Audio signal input terminal 1.
pin 12: IN 2 : Audio signal input terminal 2.
pin 13: Pre GND : Pre-Ground.
pin 14: IN 4 : Audio signal input terminal 4.
pin 15: IN 3 : Audio signal input terminal 3.
pin 16: On Time Mute : On Time Mute control.
pin 17: OUT 3+ : Non inverted power output terminal 3.
pin 18:PWR GND 3 :Power ground terminal 3.
pin 19: OUT 3- : Inverted power output terminal 3.
pin 20: VCC : Positive supply voltage.
pin 21: OUT 4+ : Non inverted power output terminal 4.
pin 22: MUTE : Mute signal input terminal.
pin 23: OUT 4- : Inverted power output terminal 4.
pin 24:PWR GND 4 :Power ground terminal 4.
pin 25: CLIP DET : Clip detection.
051-5034-90 BD3813KS Audio Sound Processor

DXZ945MP
DXZ946MP
-15-
1- 28
1- 28
1- 36
1- 5
1- 28
1- 58
1- 61
1- 60
1- 59
1- 57
1- 53
1- 54
1- 49
1- 64
1- 55
1- 55
1- 55
1- 56
1- 59
1- 41
1- 63
1- 40
1- 25
1- 62
1- 39
1- 8
1- 10
1- 24
1- 7
1- 15
1- 11
1- 16
1- 17
1- 12
1- 13
1- 14
1- 6
1- 27
1- 27
1- 9
1- 30
1- 29
1- 22
1- 33
1- 34
1- 20
1- 20
1- 21
1- 35
1- 48
1- 37
1- 42
1- 52
1- 51
1- 50
1
1- 47
1- 46
1- 44
1- 45
1- 43
1- 2
1- 4
1- 19
1- 3
1- 1
1- 23
1- 31
1- 31
1- 26
1- 32
1- 38
1- 38
1- 18
NO. PART NO. DESCRIPTION Q'TY
NO. PART NO. DESCRIPTION Q'TY
1 DCP-492-600 DCP ASSY (PE2635BA) 1
DCP-490-800 DCP ASSY (PE2635KA/B)
1-1 370-6074-00 ESCUTCHEON(PE2635BA) 1
370-6074-03 ESCUTCHEON(PE2635KA/B)
1-2 371-5777-00 TRIM PLATE 1
1-3 371-5758-00 FACE PANEL-R(PE2635BA) 1
371-5758-02 FACE PANEL-R(PE2635KA/B)
1-4 371-5759-00 FACE PANEL-L(PE2635BA) 1
371-5759-02 FACE PANEL-L(PE2635KA/B)
1-5 335-7059-00 REAR-CVR 1
1-6 335-7060-00 ILLUMI PLATE(R) 1
1-7 335-7061-00 ILLUMI PLATE(L) 1
1-8 380-5574-00 INNER KNOB 1
1-9 380-5575-00 KNOB 1
1-10 345-5355-00 RUBBER RING 1
1-11 382-6789-00 BUTTON(ENT) 1
1-12 382-6790-00 BUTTON(EJECT) 1
1-13 382-6791-00 BUTTON(ADJ/ISR) 1
1-14 382-6792-00 BUTTON(SOUND) 1
1-15 382-6793-00 BUTTON(REL)(PE2635BA) 1
382-6793-01 BUTTON(REL)(PE2635KA/B)
1-16 335-7063-00 IR-FILTER 1
1-17 335-7064-00 LENS 1
1-18 347-7189-00 DOUBLE FACE(TRIM/L) 1
1-19 347-7190-00 DOUBLE FACE(TRIM/C) 4
1-20 347-7193-00 DOUBLE FACE(T/P) 2
1-21 347-7194-00 SPACER(T/P) 2
1-22 347-7195-00 SURGE FILM(R) 1
1-23 347-7188-00 DOUBLE FACE(TRIM/R) 1
1-24 750-6720-00 SPRING (REL) 1
1-25 816-2641-50 FLAT WIRE(LCD/SW) 1
1-26 378-0537-00 BADGE 1
1-27 716-0872-01 PAD SCREW(M1.7x6) 2
1-28 716-0872-12 PAD SCREW(M1.7x8) 4
1-29 347-7196-00 SURGE FILM(L) 1
1-30 347-7200-00 DOUBLE FACE(KNOB) 1
1-31 347-7191-00 DOUBLE FACE 3
1-32 347-7192-00 DOUBLE FACE 1
1-33 347-7198-00 SHADE(ILLUMI R) 1
1-34 347-7199-00 SHADE(ES) 2
1-35 347-7197-00 SPACER(ES) 2
1-36 345-8647-00 CUSHION 1
1-37 013-9709-00 SWITCH ASSY(T/P) 1
1-38 347-7215-00 DOUBLE FACE(FACE SIDE) 2
1-39 074-1158-54 OUTLET SOCKET(4P) 1
1-40 060-4011-80 PHOTO-TR 1
1-41 001-7040-91 DIODE 2
1-42 331-3698-00 LCD-CVR 1
1-43 335-7065-00 LCD HOLDER 1
1-44 335-7066-00 ILLUMI PLATE 1
1-45 347-7201-00 REFLECTOR 1
1-46 347-7202-00 LCD FILM 1
1-47 347-7203-00 BLACK FILM 1
1-48 379-1299-81 LCD 1
1-49 716-0872-20 PAD SCREW(M1.7x4) 1
1-50 347-7204-00 PROTECT SHEET(T/P FPC) 1
1-51 347-7205-00 PROTECT SHEET(COM FPC) 1
1-52 345-5430-00 CUSHION(SEG FPC) 2
1-53 347-7206-00 SPACER(SEG FPC) 1
1-54 347-7207-00 SPACER(COM FPC) 1
1-55 013-6312-50 SWITCH 5
1-56 060-4017-90 IR-RECIEVER 1
1-57 ----------- LCD PWB 1
1-58 001-7078-90 DIODE 12
1-59 074-1239-75 OUTLET SOCKET(25P) 2
1-60 074-1239-80 OUTLET SOCKET(30P) 1
1-61 074-1205-85 OUTLET SOCKET(35P) 1
1-62 ----------- SWITCH PWB 1
1-63 076-0647-00 PLUG(16P) 1
1-64 016-6000-00 VR W/SHAFT 1
EXPLODED VIEW・PARTS LIST
DCP section

DXZ945MP
DXZ946MP -16-
D2
D1
A
B1
B2
Grease
application
Grease
application
Grease
application
D1
D2
A
B1
B2
Grease
application
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30 31
32
33
34
35
36
37
38
39
40
27
29
29
29
29
29
29
29
28
28
28
28
28
28
28
31
31
28
Finished figure
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
Inner escutcheon section
1 039-2409-00 INNER ES FPC 1
(WITHOUT COMPONENT)
2 074-1278-01 OUTLET SOKET 1
3 291-0102-00 STICKER 1
4 309-0772-02 FRONT PLATE 1
5 331-3115-01 DCP HOLDER 1
6 331-3117-01 LEVER-UP(R) 1
7 331-3118-01 LEVER-LO(R) 1
8 331-3119-00 LEVER-LO(L) 1
9 331-3120-00 LEVER-UP(L) 1
10 335-6499-00 CN-CVR 1
11 335-6505-00 ILLUMI PLATE 1
12 335-6903-00 ARM-CVR(L) 1
13 335-6904-00 ARM-CVR(R) 1
14 335-7176-00 HOOK 1
15 341-1740-00 ROLLER(ARM) 1
16 341-1802-00 SHAFT 1
17 345-8265-00 CUSHION 1
18 345-8627-00 CUSHION 1
19 346-0150-02 LEATHER SHEET 1
20 347-6275-00 FILM 1
21 347-6527-00 CUSHION 1
22 347-6528-00 INSULATER 1
23 370-5935-07 ESCUTCHEON 1
24 613-0717-00 INPUT GEAR 1
25 613-0719-00 ARM GEAR 1
26 613-0720-00 HUS-GEAR 1
27 716-0872-00 PAD SCREW(M1.7x5) 4
28 716-1468-20 SPECIAL-SCREW(M2x2.5) 10
29 716-1715-02 DECO-SCREW 11
30 716-1758-00 PAD SCREW 2
31 746-0768-20 SPECIAL WASHER 4
32 750-3303-20 SPRING(ARM) 1
33 750-3304-20 SPRING(GEAR) 1
34 750-3431-02 SPRING(HOOK) 1
35 750-3432-00 SPRING(MOTOR) 1
36 750-3457-00 SPRING 1
37 854-4380-01 EXTENSION LEAD 1
38 946-0079-01 GEAR-BOX ASSY 1
39 947-0513-02 T-LIM-GEAR-ASSY 1
40 634-0023-00 MOTOR-ASSY 1
*Grease:FLOIL31SB

DXZ945MP
DXZ946MP
-17-
NO. PART NO. DESCRIPTION Q'TY
Main section
1 331-2255-20 IC-HOLDER 1
2 074-1214-00 OUTLET SOCKET(PWR) 1
3 074-1194-00 OUTLET SOCKET(CeNET) 1
4 716-0717-10 STEEL SCREW(M2.3x3) 2
5 313-1781-00 HEAT SINK(TR) 1
6 305-0274-01 SIDE-CVR(L) 1
7 313-1844-01 HEAT SINK 1
8 313-1845-00 HEAT SINK 1
9 880-2090B TUNER PACK 1
10 092-4000-51 ANT-RECEPT 1
11 313-1651-21 HEAT SINK(TR) 1
12 345-5441-00 HEAT RUBBER 1
13 307-0699-00 REAR-CVR 1
14 855-5424-50 RCA PIN CORD(6CH) 1
15 855-5493-50 RCA PIN CORD(4CH) 1
16 305-0275-00 SIDE-CVR(R) 1
17 074-1138-70 OUTLET SOCKET(CD) 1
18 013-6103-00 TACT SWITCH(RESET) 1
19 001-7011-94 DIODE 1
20 ----------- MAIN PWB 1
21 074-1198-68 OUTLET SOCKET(SW) 1
22 076-0312-02 PLUG(MOTOR) 1
23 013-7206-50 DETECTOR SWITCH 1
24 331-3378-00 SW-HOLDER(OPEN-SW) 1
25 013-7106-00 DETECTOR SWITCH 1
NO. PART NO. DESCRIPTION Q'TY
26 714-2603-80 MACHINE SCREW(M2.6x3) 7
27 345-8701-00 CUSHION 1
28 347-6215-00 SPACER-FILM 1
29 780-2005-00 SPECIAL SCREW 2
30 347-7210-00 E-SHEET 2
31 347-7211-00 CUSHION 2
32 347-7209-00 INSULATOR 1
33 286-6361-00 SETPLATE(PE2635BA) 1
286-6414-00 SETPLATE(PE2635KA)
286-6415-00 SETPLATE(PE2635KB)
34 345-3799-20 RUBBER CAP 10
35 331-2744-00 STOPPER 1
36 303-0472-05 UPPER-CVR 1
37 347-6705-00 INSULATOR(R) 1
38 331-3324-00 CD-SUB-BRKT(REAR) 1
39 347-6821-00 SPACER FILM 2
40 929-0300-80 CD-MECH-MODULE 1
41 816-2643-50 FLAT WIRE(MECH/MAIN) 1
42 331-3581-00 MECH-BRKT(F) 1
43 347-7017-00 DOUBLE FACE 1
44 347-6536-00 PROTECT SHEET 1
45 345-5318-00 CUSHION(MECH-BRKT) 1
46 304-0460-01 LOWER-CVR 1
47 731-3008-87 TAPTIGHT(M3x8) 2
48 714-3006-81 MACHINE SCREW(M3x6) 4
49 731-3006-80 TAPTIGHT(M3x6) 9
49
49
48
16
31 31
30
39
40
41
39
26
26
38
26
37
46
32
33
44
29
4
Inner escutcheon
4
48
6
12
78
47
49
27 28
23
24 25
12
35
9
10
11
22
21
20
19
18 17
26
26
42
43
45
34
49
49
48
48
15
14
13
36
49
49
35

DXZ945MP
DXZ946MP -18-
CD mechanism section
H4
H5
G6
H6
H7
A5
A1
A2
A3
A4
G2
G3
B2
A8
A8
I1
M1
K3
K4
C1
A2
A3
G9
G8
G11
G5
G14
G6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29 30
31
32
33
34
35
36
37
38
39
40
41
42 43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
57
42
I1
I2
D2
D1
H6
H7
K1
K2
C3
67
H5
H4
32
29
H6
B1
H1
H2
H3
G13
D1
50
D2
G12
H2
H1
H3
44
A4
A5
E2 G2
G14
G5
G1
G3
E1
G4
M1
G9
G8
G11
C5
C2
G1
I2
C1
45 45
45
45
H6
C5
C2
C3
K1
K2
K3
K4
G12
G4
A1
G13
B1
B2
66
E1
E2
3-6
3-2
3-1
3-3
3-4 3-5
3-7

DXZ945MP
DXZ946MP
-19-
NO. PART NO. DESCRIPTION Q'TYNO. PART NO. DESCRIPTION Q'TY
1 SMA-182-100 SPD-MOTOR-ASSY 1
2 SMA-183-100 POW-MOTOR-ASSY 1
3 HBS-524-100 CLAMP-SUB-ASSY 1
3-1 620-1022-25 CLAMPER LINK 1
3-2 620-1023-23 CLAMPER PLATE 1
3-3 620-1024-23 SENSOR ARM 1
3-4 621-0626-21 STOPPER LINK 1
3-5 621-0627-21 DISC STOPPER 1
3-6 621-0708-20 CLAMPER RING 1
3-7 750-3471-20 SENSOR SPRING 1
4 966-0595-25 DRIVE-PLT-ASSY 1
5 966-0638-20 SH-RACK-ASSY 1
6 969-0065-31 PICK UP-ASSY 1
7 345-8704-20 CUSHION RUBBER 1
8 620-1025-22 ID-LOCK PLATE 1
9 620-1026-21 SPRING PLATE 1
10 620-1028-23 UPPER CHASSIS 1
11 620-1585-21 LOWER SHASSIS-W 1
12 621-0598-27 UPPER GUIDE 1
13 621-0600-26 SHIFT LEVER 1
14 621-0601-21 RACK 1
15 621-0602-22 LOCK ARM L 1
16 621-0603-25 LOCK ARM R 1
17 621-0605-22 GEAR COVER 1
18 621-0608-21 SECOND GEAR 1
19 621-0609-20 BASE GEAR 1
20 621-0610-20 IDLE GEAR A 1
21 621-0611-20 IDLE GEAR B 1
22 621-0612-21 ROLLER GEAR A 1
23 621-0616-20 POWER GEAR A 1
24 621-0617-20 POWER GEAR B 1
25 621-0618-20 POWER GEAR C 1
26 621-0619-20 POWER GEAR D 1
27 621-0620-20 THREAD GEAR A 1
28 621-0621-20 THREAD GEAR B 1
29 621-0622-21 ROLLER SLEEVE 2
30 621-0623-23 LS-HOLDER 1
31 621-0624-22 GUIDE RAIL 1
32 621-0629-20 LOADING ROLLER 2
33 621-0709-20 SH-BASE 1
34 621-0718-21 ROLLER GUIDE 1
35 621-0719-20 ROLLER GEAR 1
36 621-0720-20 ROLLER GEAR C 1
37 621-0721-20 ROLLER GEAR D 1
38 621-0723-20 IDLE CASE 1
39 621-0724-21 GEAR BASE 1
40 622-1660-20 ROLLER SHAFT 1
41 624-0018-01 LEAD SCREW 1
42 629-0086-20 DAMPER F 2
43 629-0087-20 DAMPER R 1
44 714-2003-81 MACHINE SCREW(M2x3) 2
45 716-1507-00 SCREW(M2x3) 7
46 716-1670-00 SCREW(M2x4) 2
47 716-1733-00 SCREW(M1.7x2.3) 2
48 716-3446-00 SCREW(M4.1x2.5) 2
49 716-3469-00 SCREW(phi1.7x4) 2
50 716-3473-00 SCREW(M2x3) 2
51 750-3465-21 ROLLER SPRING L 1
52 750-3466-20 ROLLER SPRING R 1
53 750-3467-21 SHIFT SPRING 1
54 750-3468-20 RACK SPRING 1
55 750-3469-20 CLAMPER SPRING 1
56 750-3470-20 ID-LOCK SPRING 1
57 750-3472-21 DR-SPRING F 2
58 750-3473-20 DR-SPRING RA 1
59 750-3474-20 DR-SPRING RB 1
60 750-3475-21 DR-SPRING C 1
61 803-4906-60 VINYL-COAT-WIRE(ORANGE) 1
62 816-2590-00 EXTENSION LEAD(GREEN) 1
63 816-2591-00 EXTENSION LEAD(YELLOW) 1
64 816-2592-00 EXTENSION LEAD(BLUE) 1
65 816-2593-00 EXTENSION LEAD(PURPLE) 1
66 816-2624-50 FLAT WIRE 1
67 ----------- LED PWB 1
68 ----------- CD PWB 1

DXZ945MP
DXZ946MP -20-
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
ELECTRICAL PARTS LIST
ANT1 092-4000-51 ANT-RECEPT
BL1 880-2090B TUNER PACK
C1 168-2232-55 0.022uF
C4 043-0540-02 16V1uF
C5 168-2732-55 16V 0.027uF
C6 168-2732-55 16V 0.027uF
C7 187-4763-35 16V47uF
C8 168-2232-55 0.022uF
C9 168-2232-55 0.022uF
C10 168-6822-55 6800pF
C11 042-1631-50 10V100uF
C12 042-1631-50 10V100uF
C14 166-2096-50 2pF CK
C15 166-2201-50 22pF CH
C16 168-1042-78 16V 0.1uF
C18 043-0540-02 16V1uF
C20 163-4763-15 6.3V47uF
C22 166-1011-50 100pF CH
C23 166-1011-50 100pF CH
C24 166-3311-50 330pF CH
C25 166-1501-50 15pF CH
C26 166-1801-50 18pF CH
C28 168-1832-55 0.018uF
C29 168-2232-55 0.022uF
C55 166-2201-50 22pF CH
C67 168-1032-55 0.01uF
C68 168-2232-55 0.022uF
C69 042-0671-02 10V22uF
C70 172-3341-15 0.33uF
C101 178-4742-78 0.47uF
C102 178-4742-78 0.47uF
C103 178-4742-78 0.47uF
C104 178-4742-78 0.47uF
C106 042-0560-84 16V470uF
C107 042-0560-56 50V3.3uF
C108 042-0560-63 16V22uF
C109 043-0506-50 0.1uF
C110 043-0506-50 0.1uF
C111 043-0506-50 0.1uF
C112 043-0506-50 0.1uF
C113 043-0506-50 0.1uF
C114 043-0506-50 0.1uF
C115 043-0506-50 0.1uF
C116 043-0506-50 0.1uF
C121 163-1063-35 16V10uF
C122 163-1063-35 16V10uF
C123 163-1063-35 16V10uF
C124 163-1063-35 16V10uF
C125 166-4711-50 470pF CH
C126 166-4711-50 470pF CH
C127 166-4711-50 470pF CH
C128 166-4711-50 470pF CH
C129 166-4711-50 470pF CH
C130 166-4711-50 470pF CH
C131 166-4711-50 470pF CH
C132 166-4711-50 470pF CH
C133 168-1032-55 0.01uF
C141 166-1011-50 100pF CH
C142 166-1011-50 100pF CH
C143 166-1011-50 100pF CH
C144 166-1011-50 100pF CH
C145 168-1032-55 0.01uF
C146 168-1032-55 0.01uF
C201 042-1545-00 16V2200uF
C202 172-2231-15 0.022uF
C203 042-1563-71 16V100uF
C204 042-0560-63 16V22uF
C205 168-4732-78 0.047uF
C206 168-1042-78 16V 0.1uF
C210 187-4763-35 16V47uF
C211 042-0560-63 16V22uF
C222 042-0560-84 16V470uF
C223 168-2232-55 0.022uF
C224 172-4731-15 0.047uF
C230 042-1631-50 10V100uF
C240 187-4763-35 16V47uF
C241 163-1063-35 16V10uF
C242 163-1063-35 16V10uF
C243 042-1631-50 10V100uF
C244 188-2263-37 16V22uF
C245 168-1042-78 16V 0.1uF
C246 188-2263-37 16V22uF
C247 042-1563-71 16V100uF
C248 042-1631-50 10V100uF
C249 168-1022-55 1000pF
C250 187-4763-45 25V47uF
C251 168-1042-78 16V 0.1uF
C252 168-4732-78 0.047uF
C253 168-1042-78 16V 0.1uF
C254 168-1022-55 1000pF
C255 166-1511-50 150pF CH
C256 168-2232-55 0.022uF
C257 168-1042-78 16V 0.1uF
C258 168-1042-78 16V 0.1uF
C259 189-4773-32 16V470uF
C260 187-4763-45 25V47uF
C262 168-1032-55 0.01uF
C263 043-0510-51 25V 10uF
C288 042-1452-81 10V220uF
C301 043-0540-01 10V2.2uF
C302 043-0540-01 10V2.2uF
C303 043-0540-01 10V2.2uF
C304 166-2211-50 220pF CH
C310 163-1063-35 16V10uF
C313 168-4732-78 0.047uF
C314 168-4732-78 0.047uF
C317 043-0540-01 10V2.2uF
C322 043-0540-01 10V2.2uF
C325 168-1042-78 16V 0.1uF
C326 043-0540-00 6.3V10uF
C327 043-0540-00 6.3V10uF
C328 043-0540-00 6.3V10uF
C329 043-0540-00 6.3V10uF
C330 043-0540-00 6.3V10uF
C331 043-0540-00 6.3V10uF
C332 043-0540-00 6.3V10uF
C333 043-0540-00 6.3V10uF
C334 043-0540-00 6.3V10uF
C335 043-0540-00 6.3V10uF
C337 043-0540-01 10V2.2uF
C338 043-0540-01 10V2.2uF
C339 166-1007-50 10pF CH
C340 166-1007-50 10pF CH
C341 166-1007-50 10pF CH
C342 166-1007-50 10pF CH
C401 168-1022-55 1000pF
C402 168-1022-55 1000pF
C403 042-0423-20 10V10uF
C404 168-1042-78 16V 0.1uF
C405 042-0423-20 10V10uF
C406 042-0423-20 10V10uF
C407 042-0423-20 10V10uF
C408 168-1042-78 16V 0.1uF
C409 168-1042-78 16V 0.1uF
C412 042-0423-20 10V10uF
C413 042-0423-21 10V22uF
C414 043-0540-00 6.3V10uF
C415 043-0540-00 6.3V10uF
C417 042-0423-20 10V10uF
C418 168-1042-78 16V 0.1uF
C419 168-1042-78 16V 0.1uF
C420 042-0423-20 10V10uF
C421 166-2201-50 22pF CH
C422 166-2201-50 22pF CH
C423 168-1042-78 16V 0.1uF
C424 168-1042-78 16V 0.1uF
C427 168-1042-78 16V 0.1uF
C428 168-1042-78 16V 0.1uF
C430 168-6822-55 6800pF
C431 042-0423-20 10V10uF
C435 168-1042-78 16V 0.1uF
C436 168-1042-78 16V 0.1uF
C448 043-0541-00 6.3V22uF
C449 043-0541-00 6.3V22uF
C450 043-0541-00 6.3V22uF
C451 043-0541-00 6.3V22uF
C452 043-0541-00 6.3V22uF
C453 043-0541-00 6.3V22uF
C454 043-0541-00 6.3V22uF
C455 043-0541-00 6.3V22uF
C470 043-0540-00 6.3V10uF
C471 043-0540-00 6.3V10uF
C474 043-0540-00 6.3V10uF
C475 043-0540-00 6.3V10uF
C476 043-0540-00 6.3V10uF
C477 043-0540-00 6.3V10uF
C478 042-0560-84 16V470uF
C479 042-0560-84 16V470uF
C490 166-1201-50 12pF CH
C491 166-1201-50 12pF CH
C500 043-0540-00 6.3V10uF
C501 043-0540-00 6.3V10uF
C502 043-0540-00 6.3V10uF
C503 043-0540-00 6.3V10uF
C504 043-0540-00 6.3V10uF
C505 043-0540-00 6.3V10uF
C506 043-0540-00 6.3V10uF
C507 043-0540-00 6.3V10uF
C508 163-1063-35 16V10uF
C509 166-5611-50 560pF CH
C510 166-5611-50 560pF CH
C511 043-0264-63 0.01uF
C512 043-0264-63 0.01uF
C513 166-5611-50 560pF CH
C514 166-5611-50 560pF CH
C515 043-0264-63 0.01uF
C516 043-0540-00 6.3V10uF
C517 043-0540-00 6.3V10uF
C518 166-5611-50 560pF CH
C519 166-5611-50 560pF CH
C520 166-5611-50 560pF CH
C521 166-5611-50 560pF CH
C522 043-0264-63 0.01uF
C523 043-0264-63 0.01uF
C524 043-0264-63 0.01uF
C525 043-0264-63 0.01uF
C526 043-0540-00 6.3V10uF
C527 043-0540-00 6.3V10uF
C528 043-0540-00 6.3V10uF
C529 043-0540-00 6.3V10uF
C530 043-0540-00 6.3V10uF
C531 043-0540-00 6.3V10uF
C532 043-0264-63 0.01uF
C533 043-0264-63 0.01uF
C534 166-5611-50 560pF CH
C535 166-5611-50 560pF CH
C536 043-0264-63 0.01uF
C537 166-5611-50 560pF CH
C538 166-5611-50 560pF CH
C539 043-0264-63 0.01uF
C540 043-0264-63 0.01uF
C541 043-0540-00 6.3V10uF
C542 043-0540-00 6.3V10uF
C543 166-1007-50 10pF CH
C544 166-1007-50 10pF CH
C606 168-4732-78 0.047uF
Main PWB(B1) section