Clarion NZ502E User manual

29NZ502E
English
English
INSTALLATION / WIRE
CONNECTION GUIDE
Before Starting
1. This set is exclusively for use in cars with a negative ground
12 V power supply.
2. Read these instructions carefully.
3. Besure to disconnect the battery “-” terminal before starting.
This is to prevent short circuits during installation. (Figure 1)
Package Contents
Main unit................................................... 1
Wiring harness.......................................... 1
GPS antenna ............................................ 1
Clamp for GPS antenna's cable............... 3
Double face tape for GPS Antenna .......... 1
Remote control unit.................................. 1
Battery (CR2025) ...................................... 1
(Installed in remote control)
Trim ring ................................................... 1
Cleaning cloth........................................... 1
Warranty Card .......................................... 1
Owner’s manual (CD-R) ........................... 1
Quick Start Guide and
Installation manual.....................................1
Electro tap ................................................ 2
Mounting Bracket key ............................. 2
Flush mount bolts .................................... 4
Hexagon Head Screw .............................. 5
AV cable
Rear radio stud and stopper ....................1
................................................... 1
Figure 1
Car battery
C
M
Y
CM
MY
CY
CMY
K
NZ502E_quick start guide_7-8121-2001-00-01_0807 29.pdf 1 2012-8-7 15:57:57

30 NZ502E
English
English
General Cautions
1. Do not open the case. There are no user- serviceable
parts inside. If you drop anything into the unit during
installation, consult your dealer or an authorized
Clarion service center.
2. Use a soft, dry cloth to clean the case. Never use
aroughcloth,thinner,benzine,oralcoholetc.For
tough dirt, apply a little cold or warm water to a soft
cloth and wipe off the dirt gently.
Cautions on Installation
1.Prepareallarticlesnecessaryforinstallingthe
source unit before starting.
2. This model features an operation panel that slides
forward.
On some types of cars, the operation panel may
make contact with the dashboard or gearshift
lever, in which cause it cannot be installed. Before
installing, check that the unit will not hamper
operation of the gearshift lever or obstruct your view
beforeselectingtheinstallationlocation.(Figure2)
3. Install the unit within 30° of the horizontal plane.
(Figure3)
4. If you have to do any work on the car body, such as
drilling holes, consult your car dealer beforehand.
5. Use the enclosed screws for installation. Using
otherscrewscancausedamage.(Figure4)
NZ502E
Figure3
NZ502E
Figure2
Gearshiftlever
(Checkthatitdoesnot
touchtheLCD)
Dashboard
Gearshiftlever
Figure4
Chassis Chassis
Damage
Max.8mm(M5screw)
NZ502E_quick start guide_120718.indd 30 2012-7-18 13:48:50

31NZ502E
English
English
Universal Mount
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracketinward, then secure the stopper as
showninFigure 6.
2. Insert the main unit into the universal
mounting bracket until it locks.
3. Mount the outer escutcheon so that all the
hooks are locked.
Note:
•Some carmodelsrequire specialmountingkitsfor
proper installation.Consult your Clariondealerfor
details.
•Fasten thefront stoppersecurely to prevent the
main unit from comingloose.
•Console opening dimensions
Hole
7-3/16" (182 mm)
2-1/16"(53 mm)
Hole
Hexagonal
bolt
Instrument panel
Stoppers
Screwdriver
Universal mounting bracket
Stoppers
2-Spring
Main Unit
Outer escutcheon
Note:
Set theouter escutcheon
so that itsmetallicparton
thebacksidefitsthe upper
edge of themainunit.
Figure 5
Installing The Main Unit
NZ502E_quick start guide_120718.indd 31 2012-7-18 13:48:51

32 NZ502E
English
English
Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
This unit is designed for fixed installation in the
dashboard.
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (*2). (Figure 7)
If the vehicle is not equipped with a factory-
installed radio, obtain an installation kit to install
the main unit in the following procedure.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the
direction of arrow to remove it. Repeat the
same for the other side to remove the springs
from the both sides. (Figure 6)
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped
for TOYOTA and NISSAN vehicles;
modification,such as drillingnewholes,ofthe
mounting brackets may be required for other
models.
3. Secure the unit in the dashboard, and then
reassemble the dashboard and the center
panel.
Note:
*1The parts and screws with this mark are used to install radio or included in the installation kit.
*2The screws with this mark are enclosed in this set.
*3In some cases, the center panel may require some modification (trimming, filling, etc.).
*4If thehook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool.
MainUnit 2-ScrewEngaging claw
2-Spring
ScrewdriverFigure 6
Mounting bracket *1
(1pairfortheleftandright
sides)
4-Hexagonal screw *2
(M5 ×8)
Center Panel *3
Pocket
*4
Figure 7
MainUnit
*1
*1
*1
*1
*1
*1
*1
*1
NZ502E_quick start guide_120718.indd 32 2012-7-18 13:48:51

33NZ502E
English
English
Cautions on Wiring
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the wires.
 Keepthemwellawayfromtheengine,andexhaustpipe,etc.Heatmaydamagethewires.
3. If the fuse should blow, check to see if the wiring is correct.
 Ifafuseisblown,replaceitwithanewoneofthesameamperageratingastheoriginal(15AFUSE).
4.Toreplacethefuse,removetheoldfuseonthebackoftheunitandinsertthenewone.(Figure8)
NOTE:
There are various types of fuse holder. Do not let the battery side touch other metal parts.
Figure8
Fuse(15AFUSE)
After the connection, fix the cord by a clamp
or insulation tape for protection.
Fuseholder
CAUTION
NZ502E_quick start guide_120718.indd 33 2012-7-18 13:48:51

34 NZ502E
English
English
Installtion Guide
17
Installationsguide
NZ502E_quick start guide_120718.indd 34 2012-7-18 13:48:52
WARNING
• Do not install the GPS antenna in a place where it may interfere with the operation of the
airbag or hinder the driver’s visual range.
• Do not use the navigation system with the GPS antenna cord cut off. The power cables in the
cord may be short-circuited.
Note:
• ThesuppliedGPSantennaisforinstallinginsidethevehicle.Donotinstallitoutsidethe
vehicle.
• InstalltheGPSantennamorethan50cmawayfromthemainunit,otheraudiodevicessuch
asCDplayer,andaradardetector.Ifitisinstallednearthesedevices,GPSreceptionmaybe
impaired.
• To improvetheGPSsignalreception,installtheGPSantennahorizontallyonaflatplane.
• DonotwaxorpaintthecoveroftheGPSantenna.Thismayreducetheperformanceofthe
GPSantenna.
• InstalltheGPSantennaatleast10cmawayfromthewindshield.
• WipeoffthedirtofthemountingsurfacebeforeinstallingtheGPSantenna.
GPS antenna
• Mount the GPS antenna.
Stick it surely on a at plane of
the passengerside dashboard
where GPS signal interruption is
minimized.
• Wire the GPS antenna cord.
Fasten the cord using the cord
holders.
Cord holder
Double-sided tape
Bottom face of the GPS antenna
• Stick the double-sided tape to the bottom
face of the GPS antenna.

35NZ502E
English
English
Wire Connections
Note:
•Beforeinstalling,besuretodisconnectthenegativecableofthecarbattery.
•Intheoptionaldevices,theRCAcablesandtheConnectorcablesareseparately-solditems.
Black
Radio Antenna Jack
4-Channel Amplifier
Subwoofer 1
Subwoofer 2
Line Out
Rear R
Line Out
Rear L
Line Out
Front R
Line Out
Video Out
Front L
Video in
Audio/R
Audio/L
Camera
Yellow
White
White
Red
Red
Red
White
Yellow
Purple
Gray
Gray
Red
Black
Black
Black
Black
White
Steering Wheel
Remote Control Terminal
Yellow
Monitor
Yellow
White
Red
Red
Rear zone out R
Rear zone out L
Red
White
Green
GPS
Antenna
External
Microphone
Connection
iPod/iPhone
MIC
SWI
CAMERA
VISUAL OUT
VISUAL IN
DVB-T Tuner (DTX501E)
DTV
CCA-748 (sold separately)
Rear Vision Camera
Refer to
page 36
NZ502E_quick start guide_120718.indd 35 2012-7-18 13:48:52

36 NZ502E
English
English
See next page for how to connect the parking brake cord.
15A
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Description
No.
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
B-1
B-2
B-3
B-4
B-5
B-6
B-7
B-8
Rear right-
Rear right+
Rear left-
Rear left+
Front left-
Front left+
Front right+
Front right-
GND
Illumination
Auto antenna
+12V accessory
+12V main power
+12V main power (Yellow)
Auto antenna (Blue)
Phone interrupt (Brown)
Parking (Grass-green)
Remote (Blue/White)
Reverse (Purple/White)
+12V accessory (Red)
No. Description
3
4
5
6
7
2
1
3
4
5
6
7
2
1
!!!!Warning!!!!
Parking brake safety
device must be connected
for complete operation
Yellow
Red
Yellow
Red
For VW and Audi: Change wiring as above
Note:
*1: Connecting the PHONE INTERRUPT terminal
The phone interrupt will mute the audio if the lead receives a negative or ground signal.
NZ502E_quick start guide_120718.indd 36 2012-7-18 13:48:52

37NZ502E
English
English
Connecting the parking brake cord
Connect the cord to parking brake lamp ground in the meter panel.
Note:
•ConnectingtheparkingbrakecordtolampgroundallowsyoutowatchiPod/iPhonevideo/DVDvideo/AVinputwhen
theparkingbrakeisengaged.
•Whentheparkingbrakecordisnotconnected,themonitorwillnotshowanyvideosources.
•If“AUDIOONLY”appearsonthescreenjustafterturningontheACCpowerofthecar,releasetheparkingbrake
whileconrmingsafety,andthenengagetheparkingbrakeagain.
Connecting the accessories
• Connecting to the external amplier
Theexternalamplierscanbeconnectedtothe6channelRCAoutputconnections.Ensurethattheconnectors
are not grounded or shorted to prevent damage to the unit.
• Connecting to iPod/iPhone device
TheiPod/iPhonedevicecanbeconnectedtodedicatediPod/iPhoneconnectiononthemainunit.Fordetailed
information,refertotheinstructionsheetormanualfortheiPod/iPhonecable.
Note:
•ThisunitmaynotsupportallfunctionsofalliPod/iPhonedevices.
•TheiPod/iPhoneconnectionwillchargeyouriPod/iPhoneunlesstheiPod/iPhonebatteryiscompletelydepleted.If
the specified cord of the cellular phone is connected to the phone interrupt cord of the main unit, the audio mute is
activated when cellular phone in use.
Parkingbrakelamp
cord to battery
Electro-tap
Parkingbrake
signal cord
Parkingbrake
signal cord
Stopper
Parkingbrake
signal cord
Parkingbrake
Parkingbrakecord
(Grass-green)
Parkingbrakecord
(Grass-green)
How to attach the electro-tap
1.PlacetheParkingbrakecordatthestopper,and
fold it back in the direction of the arrow
2.PasstheParkingbrakesignalcordthrough,and
fold it back in the direction of the arrow.
NZ502E_quick start guide_120718.indd 37 2012-7-18 13:48:52