Clarity XLCgo User manual

User Guide

E
N
G
L
I
S
H
1
2
2
3
4
4
Contents
Product Specifications
Components
XLCgo Overview
Charging Your XLCgo
Getting Started
Pairing Your XLCgo with a Mobile device
Pairing Your XLCgo with DECT devices
5
6
8
10
13
Reconnecting Your XLCgo
Using Your XLCgo
Troubleshooting
Safety Instructions
Regulatory/Compliance Statement
55

1
E
N
G
L
I
S
H
Product Specifications
Operating Distance:
Operating Temperature:
Charging Time*:
Talk Time*:
Standby Time*:
Battery Type and Capacity:
10 meters with no obstructions
32F-104F
Around 3 hours
Up to 10 hours
Up to 100 hours
LITHIUM-ION POLYMER, 3.7V,950 mAh
*Varies by mobile phone settings and operator

2
Components
Thank you for choosing the Clarity XLCgo. Inside the package, you should find:
1 XLCgo main unit
1 Charging Cradle
1 USB cable
1 Air Vent Holder
1 User Guide
1 Lanyard
1
2
3
7
4
5
6
9
XLCgo Overview
1. Pairing Button
2. Tone Button
3. Volume Wheel
4. Answer on/off
5. Boost Button
6. Mute/ringer off Button
7. Power Switch
8. Audio Mode Switch
9. Charging Socket
10. 3.5mm Headphone Jack
8
10

3
E
N
G
L
I
S
H
Charging Your XLCgo
Before using your XLCgo for the first time, please plug the charger into the power source and
connect the other end to the charging socket on XLCgo or place in charging cradle to fully
charge the battery.
• Use only the supplied charger for charging
• Charging indication will be delayed a few seconds if XLCgo has not been used for a long
period of time.
•Battery Pack model BT198555/BT298555 supplied by SHENZHEN BYD LITHIUM BATTERY
COMPANY LIMITED
•For pluggable equipment, the socket-outlet (power adapter) shall be installed near the
equipment and shall be easily accessible.
•Rating label is at charger bottom.
Status Status Indicator Audio (Earpiece)
1. Charging Green light flashing No sound
2. Fully charged Green light steady then off No sound
3. Low battery Red light flashes "Battery Low"
4. Dead battery OFF No sound

4
Getting Started
Turning Your XLCgo On and Off:
A. Turning on
Push the power switch up
B. Turning off
Push the power switch down
Pairing Your XLCgo with a mobile device
1. Press and hold the Pair button on the side of the XLCgo until the pairing light starts
flashing red and blue and you hear "Start pairing with mobile device."
2. Open the settings on your mobile phone so that it begins searching for new devices.
3. Place the XLCgo and your device where they are close to each other.
4. Search for devices in your settings menu on your mobile device and select “Clarity”
5. When pairing is complete, the XLCgo’s status indicator will be steady blue and you
will hear "mobile device connected."

5
E
N
G
L
I
S
H
Pairing XLCgo with Clarity DECT devices
XLCgo pairs with the following Clarity DECT devices as an expandable speakerphone: XLC8,
XLC7BT, XLC3.4+ and XLC4.
1. Step one: Enter pairing mode on DECT base
•Press and hold the [FIND] key on base for 5 seconds, until the visual ringer starts flashing
2. Step two: Enter pairing mode on XLCgo
•Turn on XLCgo. Place it in the charging cradle and press & hold [PAIR] key (around 5
seconds) until you hear "Start pairing with base station" and DECT indicator flashes
green and red alternately. Then XLCgo enters DECT pairing mode.
3. Step three: Connection to the DECT device
•XLCgo is connected with the device automatically as soon as they are paired. When
connected, you hear voice guidance “Base station connected”. If not, it announces
"registration failed."
Reconnecting Your XLCgo
1. If XLCgo has been turned off, it will reconnect to the phone automatically after turning it
on; if not, press reconnect on the phone.
2. If the phone has been powered off and XLCgo is then disconnected, reconnect it via the
phone’s menu when the phone is on again. Or, turn XLCgo off and then back on.

6
Using Your XLCgo
1. Answer/End Calls
Press green answer key once
2. Adjust volume
Roll the Volume up or Volume down to increase/decrease the volume.
3. Boost Volume
Press the boost button to add additional volume to your phone calls
4. Audio Modes
Use this switch to change the audio mode
5. Mute/Silence Ringer
Press to mute phone calls while on a call or press to silence the ringer when a call is not
active

7
E
N
G
L
I
S
H
a. Please use the mobile phone for DIALING/HOLD/REJECT and other functions.
b. XLCgo is designed to work with mobile phones; the compatibility of some features
is not guaranteed for all devices.
Using Your XLCgo

8
Troubleshooting
I cannot pair with my mobile phone
- Ensure your XLCgo is powered on and fully charged
- Ensure the pairing function is turned on on your phone
-Ensure XLCgo is in pairing mode (flashes blue and red)
-Ensure XLCgo is in range of your phone.
If the above steps do not solve the problem, please turn o XLCgo and recharge it, and.then
try again.
-
My phone cannot be auto-reconnected XLCgo
- Manually connect XLCgo from your mobile phone
- Turn off the phone, then turn on again
- Turn off XLCgo, then turn on again.

9
E
N
G
L
I
S
H
If the above steps do not solve the problem, turn o XLCgo and reset it, then pair
XLCgo with your phone again.
I hear a “Battery Low” alert during the call, what happens?
- This is the Low battery alert. Please charge XLCgo.
I hear some noise during the call, why?
- There is an obstruction between XLCgo and your mobile. Please remove it. Alternately, try
relocating the phone and don’t hold it in your hand.

10
To reduce the risk of fire, electric shock, injury to persons and damage to property, read all
operating instructions and the following safety instructions before using your Clarity product.
Operating, storage and charging temperature is 10˚C to 40˚C (50˚F to 104˚F).
• Only use those Clarity products and accessories designed for use with this product.
• If you experience a skin irritation after using this product, discontinue use and contact
Clarity.
• CHILDREN. Never allow children to play with the product-small parts may be a choking
hazard.
• Do not disassemble the product as this may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock or fire when the product is
subsequently used.
• Unplug, discontinue use and contact Clarity if the product overheats or has a damaged
outer casing, cord or plug.
• Exposure to high volume sound levels or excessive sound pressure may cause temporary
or permanent damage to your hearing. Although there is no single volume setting that is
appropriate for everyone, you should always use your XLCgo with the volume set at
moderate levels and avoid prolonged exposure to high volume sound levels. The louder
the volume, the less time is required before your hearing could be affected. It is best to
not use this product directly next to your ear.
Safety Instructions

11
E
N
G
L
I
S
H
If you experience hearing discomfort, you should stop listening to the device through
your XLCgo and have your hearing checked by your doctor. To protect your hearing, some
hearing experts suggest that you:
1. Set the volume control in a low position before using your XLCgo and use as low a
volume as possible.
2. Avoid turning up the volume to block out noisy surroundings. Whenever possible, use
your XLCgo in a quiet environment with low background noise.
3. Limit the amount of time you use XLCgo at high volume levels.
4. Turn the volume down if the sound from the XLCgo preventsyou from hearing
people speaking near you.
WARNING:
•Do not expose your XLCgo to contact with sharp objects as this will cause scratches
and damage.
•Do not stick anything inside XLCgo as this may damage internal components.
•Only replace battery with the same type as a different type can cause damage and
defeat a safeguard.
•Do not use abrasive cleaning products or solvents to clean XLCgo.
•Do not expose XLCgo to extremely high or low temperatures that a battery can be
subjected to during use, storage or transportation, use under 1kpa and 2000m.

12
Charging Warnings
•Use only the charger supplied by Clarity to charge the product and follow the charging
instructions provided. Do not use the charger for any other purpose. Ensure that the
voltage rating corresponds to the power supply you intend to use.
Battery Warnings
• Do not dispose of the product in a fire or heat above 40°C (104°F), or mechanically
crushing or cutting of battery that can result in an explosion.
• RECYCLING The product must be recycled or disposed of properly. Contact your local
recycling center for battery removal and proper disposal.
•Leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of flammable liquid or gas;
•A battery subjected to extremely low air pressure that may result in an explosion or
leakage of flammable liquid or gas.

13
E
N
G
L
I
S
H
Regulatory/Compliance Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. Privacy of communications may not be ensured when using this equipment.

14
Industry Canada statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada's license-exempt RSS(s). Operation is subject to the following
two conditions: (1) This device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. This product
meets the applicable Innovation, Science and Economic Development Canada technical
specifications.
Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. For body worn
operation, this equipment has been tested and meets the FCC RF exposure guidelines. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.
Limited Warranty
Clarity offers a one (1) year limited warranty. For warranty details, conditions and technical
assistance, please visit our website: www.clarityproducts.com/warranty.

Clarity Products LLC
6131 Preservation Drive • Chattanooga, TN 37416
Tel: [phone] • Fax: [phone]
Website: www.clarityproducts.com
©2020 Clarity Products LLC. Clarity is trademark of Clarity Products LLC. registered in the US
and other countries. XLCgo, XLC8, XLC7BT, XLC3.4+ and XLC4 are trademarksof Clarity
Products LLC.
RevA (2-2020)
Printed in China
A ids