Clarke FOCUS II MICRO RIDER 26D User manual

Micro Rider
READ THIS BOOK
LEA ESTE MANUAL
LISEZ CE MANUEL
EN
ES
FR
English (1 - 28)
Español (29 - 56)
Français (57 - 84)
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke machine
could result in injury to you or to other personnel; damage to the machine or to other property could
occur as well. You must have training in the operation of this machine before using it. If your operator(s)
cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
Instructions For Use - Original Instructions / Instrucciones de uso / Instructions d’utilisation
Models: 9087278020 - 9087280020
Form No. 9099236000 - 7/11 - Revised 6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 1
7/11
TABLE OF CONTENTS
INTRODUCTION............................................................................................................................................. 2
MANUAL PURPOSE AND CONTENTS .......................................................................................................................................... 2
TARGET........................................................................................................................................................................................... 2
HOW TO KEEP THIS MANUAL....................................................................................................................................................... 2
IDENTIFICATION DATA................................................................................................................................................................... 2
OTHER REFERENCE MANUALS................................................................................................................................................... 2
SPARE PARTS AND MAINTENANCE............................................................................................................................................. 2
CHANGES AND IMPROVEMENTS ................................................................................................................................................ 2
OPERATION CAPABILITIES........................................................................................................................................................... 2
CONVENTIONS .............................................................................................................................................................................. 2
UNPACKING/DELIVERY ................................................................................................................................ 3
SAFETY ..........................................................................................................................................................3
VISIBLE SYMBOLS ON THE MACHINE......................................................................................................................................... 3
SYMBOLS THAT APPEAR ON THIS MANUAL............................................................................................................................... 4
GENERAL INSTRUCTIONS............................................................................................................................................................ 4
MACHINE STRUCTURE ................................................................................................................................................................. 6
CONTROL PANEL........................................................................................................................................................................... 8
ACCESSORIES/OPTIONS ............................................................................................................................. 9
TECHNICAL DATA ......................................................................................................................................... 9
WIRING DIAGRAM........................................................................................................................................................................ 10
USE ...............................................................................................................................................................12
BATTERY CHECK/SETTING ON A NEW MACHINE .................................................................................................................... 12
BATTERY INSTALLATION AND BATTERY TYPE SETTING (WET OR GEL/AGM)..................................................................... 13
BEFORE MACHINE START-UP.................................................................................................................................................... 14
MACHINE START AND STOP....................................................................................................................................................... 17
MACHINE OPERATION (SCRUBBING/DRYING)......................................................................................................................... 17
TANK EMPTYING.......................................................................................................................................................................... 19
AFTER USING THE MACHINE..................................................................................................................................................... 20
PUSHING/TOWING THE MACHINE............................................................................................................................................. 20
MACHINE LONG INACTIVITY ...................................................................................................................................................... 20
MAINTENANCE............................................................................................................................................ 21
SCHEDULED MAINTENANCE TABLE ......................................................................................................................................... 21
MACHINE WORKING HOUR CHECK .......................................................................................................................................... 21
SQUEEGEE CLEANING ............................................................................................................................................................... 22
SQUEEGEE BLADE CHECK AND REPLACEMENT.................................................................................................................... 22
BRUSH/CYLINDRICAL BRUSH CLEANING................................................................................................................................. 23
RECOVERY TANK CLEANING ..................................................................................................................................................... 23
VACUUM SYSTEM MOTOR FILTER CLEANING......................................................................................................................... 24
SOLUTION FILTER CLEANING.................................................................................................................................................... 24
BATTERY CHARGING .................................................................................................................................................................. 25
CHEMICAL MIXING SYSTEM DRAINING .................................................................................................................................... 26
FUSE CHECK/REPLACEMENT.................................................................................................................................................... 26
SAFETY FUNCTIONS .................................................................................................................................. 26
EMERGENCY PUSH-BUTTON..................................................................................................................................................... 26
ANTI-SKID SAFETY SYSTEM ...................................................................................................................................................... 26
DRIVER’S SEAT MICROSWITCH................................................................................................................................................. 26
ELECTROMAGNETIC BRAKE...................................................................................................................................................... 26
TROUBLESHOOTING.................................................................................................................................. 27
SCRAPPING .................................................................................................................................................28
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
2FOCUS II Micro Rider - 9099236000 7/11
INTRODUCTION
NOTE
The numbers in brackets refer to the components shown in Machine Description chapter.
MANUAL PURPOSE AND CONTENTS
The purpose of this Manual is to provide the operator with all necessary information to use the machine properly, in a safe and
autonomous way. It contains information about technical data, safety, operation, storage, maintenance, spare parts and disposal.

Clarke in case of doubts concerning the interpretation of the instructions and for any further information.
TARGET


from the non-observance of this prohibition.
HOW TO KEEP THIS MANUAL
The User Manual must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause
damage to it.
IDENTIFICATION DATA
The machine serial number and model are shown on the plate (21) on the steering column.

serial number.

MACHINE model ...............................................................................
MACHINE serial number ...................................................................
OTHER REFERENCE MANUALS
– Electronic Battery Charger Manual (an integral part of this Manual, and available upon request)
Moreover, the following Manuals are available:
– Service Manual (that can be consulted at any Clarke Service Center)
– Spare Parts List (supplied with the machine)
SPARE PARTS AND MAINTENANCE

Centers. Only original spare parts and accessories must be used.
Call Clarke for service or to order spare parts and accessories, specifying the machine model and serial number.
CHANGES AND IMPROVEMENTS
Clarke constantly improves its products and reserves the right to make changes and improvements at its discretion without being

Any change and/or addition of accessory must be approved and performed by Clarke.
OPERATION CAPABILITIES



CONVENTIONS
Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say on the driver’s seat
(17).
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 3
7/11
UNPACKING/DELIVERY
To unpack the machine, carefully follow the instructions on the packing.
To move the machine manually, see the Pushing/Towing The Machine paragraph.
Upon delivery carefully check that the machine and its packing have not been damaged during transportation. In case of visible
damages, keep the packing and have it checked by the carrier that delivered it. Call the carrier immediately to complete a damage
claim.
Check that the machine is equipped with the following features:
– Technical documents:
 Scrubber-dryer User Manual with Spare Parts List
 Battery Charger Manual
– 2 lamellar fuses
– 1 battery charger spare connector
– 2 shims for 6V battery housing
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary
precautions to safeguard people and property.
The operator’s cooperation is essential in order to prevent injury. No accident prevention program is effective without the total
cooperation of the person responsible for the machine operation. Most of the accidents that may occur, are caused by failure to
comply with the simplest rules for exercising prudence. A careful and prudent operator is the best guarantee against accidents and
is essential for successful completion of any accident prevention program.
VISIBLE SYMBOLS ON THE MACHINE
WARNING!
Carefully read all the instructions before performing any operation on the machine.
WARNING!
Do not wash the machine with direct or pressurized water jets.
WARNING!

6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
4FOCUS II Micro Rider - 9099236000 7/11
SYMBOLS THAT APPEAR ON THIS MANUAL
DANGER!
It indicates a dangerous situation with risk of death for the operator.
WARNING!
It indicates a potential risk of injury for people or damage to objects.
CAUTION!
It indicates a caution or a remark related to important or useful functions. Pay careful attention to the
paragraphs marked by this symbol.
NOTE
It indicates a remark related to important or useful functions.
CONSULTATION
It indicates the necessity to refer to the User Manual before performing any procedure.
GENERAL INSTRUCTIONS

DANGER!
–Before performing any maintenance, repair, cleaning or replacement procedure disconnect the battery
connector and remove the ignition key.
–This machine must be used by properly trained operators only.
–
explosive gases are released.
–Do not wear jewerly when working near electrical components.
–Do not work under the lifted machine without supporting it with safety stands.
–
This machine is not suitable for collecting dangerous powders.
–Battery charging produces highly explosive hydrogen gas. Keep the tank assembly open during battery

WARNING!
–
–
number plate, match the electrical mains voltage.
–Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as
a handle. Do not close a door on the battery charger cable, or pull the battery charger cable around sharp
edges or corners. Do not run the machine on the battery charger cable.
–Keep the battery charger cable away from heated surfaces.
–Do not use the machine if the battery charger cable or plug is damaged. If the machine is not working as it
should, has been damaged, left outdoors or dropped into water, return it to the Service Center.
–
in. Before performing any maintenance procedure, disconnect the battery charger cable from the electrical
mains.
–Do not smoke while charging the batteries.
–To avoid any unauthorized use of the machine, remove the ignition key.
–Do not leave the machine unattended without being sure that it cannot move independently.
–Always protect the machine against the sun, rain and bad weather, both under operation and inactivity

not be used or kept outdoors in wet conditions.
–
–This machine is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the machine by a person responsible for they safety. Children should be
supervised to ensure that they do not play with the machine.
–Close attention is necessary when used near children.
6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 5
7/11
WARNING!
–
–Take all necessary precautions to prevent hair, jewerly and loose clothes from being caught by the machine
moving parts.
–Do not use the machine on incline.
–Do not tilt the machine more than the angle indicated on the machine itself, in order to prevent instability.
–Do not use the machine in particularly dusty areas.
–
–If the machine is to be used where there are other people besides the operator, it is necessary to install the
pivoting light (optional).
–While using this machine, take care not to cause damage to people or objects.
–Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.
–
–The machine operating temperature must be between +32°F and 104°F (0°C and +40°C).
–The machine storage temperature must be between +32°F and 104°F (0°C and +40°C).
–The humidity must be between 30% and 95%.
–
–
–Do not use the machine as a means of transport.
–
–
–Do not tamper with the machine safety guards and follow the ordinary maintenance instructions
scrupulously.
–Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged.
Always keep the openings free from dust, hairs and any other foreign material which could reduce the air

–
–To manually move the machine, the electromagnetic brake must be disengaged. When the operation is over,
the electromagnetic brake must be activated again. Do not use the machine when the electromagnetic brake
handwheel is screwed down.
–If the machine must be pushed for service reasons (missing batteries, discharged batteries, etc.) do not

–This machine cannot be used on roads or public streets.
–Pay attention during machine transportation when temperature is below freezing point. The water in the
recovery tank or in the hoses could freeze and seriously damage the machine.
–
brushes or pads could reduce safety.
–
assistance from the authorized personnel or from an authorized Service Center.
–If parts must be replaced, use ORIGINAL spare parts from an Authorized Dealer or Retailer.
–To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of

–Do not wash the machine with direct or pressurized water jets, or with corrosive substances.
–When WET batteries are installed on the machine, do not tilt the machine for more than 30° from the
horizontal plane to prevent the highly corrosive acid from leaking out of the batteries. If the machine must
be tilted to perform any maintenance procedure, remove the batteries.
–The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries,

6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
6FOCUS II Micro Rider - 9099236000 7/11
MACHINE DESCRIPTION
MACHINE STRUCTURE
1. Steering wheel
2. Control panel (see the following paragraph)
3. Ignition key
4. Forward/reverse gear pedal
5. Footboard
6. Front steering, driving and braking wheel
7. Electromagnetic brake unlocking lever
8. Emergency push-button
9. Battery connector
10. Brush/pad-holder deck
11. Bumper wheel
12. 
13. Solenoid valve
14. Solution/clean water opening/closing tap
15. Squeegee hook
16. Battery charger
17. Seat
18. Squeegee blades assembly
19. Recovery tank assembly
20. Recovery tank cover
17 98
15
3
2
1
14
19
16
20
18 13 12 11 10 465
7
P100431
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 7
7/11
MACHINE STRUCTURE (Continues)
21. 
22. Solution/clean water tank
23. 
24. Recovery water drain hose
25. Tank assembly stand
26. Container with debris collection grid
27. 
28. BOOST®vibrating deck
29. Bumper wheel
30. Squeegee
31. Squeegee vacuum hose
32. Squeegee bumper wheels
33. Squeegee support wheels
34. Squeegee mounting handwheels
35. Squeegee pitch adjusting handwheel
36. Vacuum system motor
37. 
38. Battery connection diagram
39. Batteries
40. Battery caps
41. Battery charger cable
42. Detergent tank (*)
43. Electronic component compartment cover
44. (Lifted) recovery tank assembly and driver’s seat
45. Solution/clean water draining adapter
46. Solution/clean water drain tap
(*) Only for machines with Chemical Mixing System (optional)
Front
24V
21 27 26
33
34
30
33
34
35
32
31
22
23
45
24
322829 46
38
4039
25
42
41
43
44
37 36 38
P100432
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
8FOCUS II Micro Rider - 9099236000 7/11
CONTROL PANEL
51. Reverse gear activation/deactivation switch
52. Reverse gear LED indicator
53. Detergent concentration control switch (*)
54. Detergent concentration LED indicators (*)
55. Mute function switch
56. Mute function switch LED
57. Horn switch
58. Ignition key
59. 
60. 
61. 
62. Battery warning lights
 Green warning light - charged battery
 Yellow warning light - semi-discharged battery
 Red warning light - discharged battery
63. Brush/pad-holder deck and squeegee lifting/lowering
switch
64. Brush/pad-holder deck and squeegee lifting/lowering LED
indicator
65. Vacuum system and squeegee lifting/lowering switch
66. Vacuum system and squeegee lifting/lowering LED
indicator
67. Extra-pressure switch
68. Extra pressure led indicator
69. Drive speed adjusting switches (enabled only when the
brushes are running)
70. Drive speed LED indicators
71. Hour counter and solution level display:
 When the machine is started, it displays for a few
seconds the number of working hours which have been
performed.
 While using the machine, it displays the solution/
washing water level in the tank (in percentage).
 When the level is above 90%, the display indicates
“FUL”.
 When the level is under 30%, the display indicates
“LO”.
 
NOTE
The display could indicate “LO” even if the tank is
not completely empty, thus allowing to complete
the cleaning cycle; in any case, it is recommended

brushes.
72. Anti-skid control activation LED indicator
73. Steering wheel height control lever
(*) Only for machines with Chemical Mixing System (optional)
69
7061
62 72
57
56
55
51
52
58
5960
73
64
63
67
68
65
53
54
66
71
P100433
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 9
7/11
ACCESSORIES/OPTIONS
In addition to the standard components, the machine can be equipped with the following accessories/options, according to the

– GEL/AGM batteries
– Brushes of different materials
– Pads of different materials
– Squeegee blades of different materials
– Chemical Mixing System
– Flashing light
– Mop and trash kit
– 0.9 HP (670 W) vacuum system motor
For further information concerning the optional accessories, contact an authorized Retailer.
TECHNICAL DATA
General technical data
Description FOCUS II MICRO RIDER
26D
FOCUS II MICRO RIDER
28 BOOST
Cleaning width 26 in (660 mm) 28 in (710 mm)
Squeegee width 35 in (890 mm)
Solution/clean water tank capacity 21 USgal (80 liters)
 0.26 to 0.8 USgal/min (1 to 3 liters/min)
Rear wheel diameter 9.8 in (250 mm)
 72 psi (0.5 N/mm2)
 130 psi (0.9 N/mm2)
Front steering, driving and braking wheel diameter 8.8 in (225 mm)
Vacuum system motor power 0.56 HP (420 W)
Drive system motor power 0.4 HP (300 W)
Maximum speed 3.7 mph (6 km/h)
Maximum gradient when working 2% (1.14°)
Sound pressure level at workstation (ISO 11201, ISO 4871, EN 60335-2-72) (LpA) 65 dB(A) ± 3 dB(A)
Machine sound pressure level (ISO 3744, ISO 4871, EN 60335-2-72) (LwA) 82 dB(A) 83 dB(A)
Vibration level at the operator’s arms (ISO 5349-1, EN 60335-2-72) < 98.4 in/s2(< 2.5 m/s2)
Vibration level at the operator’s body (ISO 2631-1, EN 60335-2-72) 3.1 in/s2(0.8 m/s2)
Battery compartment size (length x width x height) 14.9 x 21.2 x 11.8 in (380 x 540 x 300 mm)
Battery type 4 x 6V batteries, 180 Ah C5 (WET)
4 x 6V batteries, 180 Ah C5 (GEL/AGM)
Vacuum system capacity 0.0098 MPa (1,000 mmH2O)
Machine height 48.4 in (1,230 mm)
Machine maximum length 53.5 in (1,360 mm)
Minimum turning radius 59.0 in (1,500 mm)
Machine width without squeegee 670 mm 730 mm
Technical data for machines with brush/pad-holder deck
Description FOCUS II MICRO RIDER 26D
Brush/pad diameter 13.0 in (330 mm)
Weight without batteries and with empty tanks 385.8 lb (175 kg)
Maximum weight with batteries, full tanks and operator (GVW) 1,012 lb (459 kg)
Brush/pad motor power 2 x 0.53 HP (2 x 400 W)
Brush/pad-holder speed 230 rpm
Brush/pad-holder pressure with extra-pressure function turned off 66.1 lb (30 kg)
Brush/pad-holder pressure with extra-pressure function turned on 105.8 lb (48 kg)
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
10 FOCUS II Micro Rider - 9099236000 7/11
Technical Data with BOOST®deck
Description FOCUS II MICRO RIDER 28 BOOST
Brush size 28 x 14 in (711 x 355.6 mm)
Weight without batteries and with empty tanks 401 lb (182 kg)
Maximum weight with batteries, full tanks and operator (GVW) 1,027 lb (466 kg)
BOOST®deck motor power 0.75 HP (560 W)
Motor speed 2,200 rpm
BOOST®deck pressure with extra-pressure function turned off 81.5 lb (37 kg)
BOOST®deck pressure with extra-pressure function turned on 121 lb (55 kg)
WIRING DIAGRAM
Key
BAT 24V batteries
BE Flashing light (optional)
BRK Electromagnetic brake
BZ1 Reverse gear warning buzzer/horn
C1 Battery connector
C2 Battery charger main connector
C3 Battery charger sub-connector
C4 Brush deck connector
CH Battery charger
EB1 Function electronic board
EB2 Display electronic board
EB3 Dashboard instrument electronic board
ES1 Brush electromagnetic switch
EV1 Solenoid valve
F0 Battery fuse
F1 Brush deck fuse
F2 Main electronic board fuse
F3 Signal circuit fuse
F4 Actuator fuse
K1 Ignition switch
M1.1,2 Brush motor
M2 Vacuum system motor
M3 Drive system motor
M4 Detergent pump (optional)
M5 Brush deck actuator motor
m0 Actuator position 0 microswitch (Raised)
m1 Actuator position 1 microswitch (Normal)
m2 Actuator position 2 microswitch (Extra pressure)
M6 Squeegee actuator motor
PR1 Solution/clean water level pressure switch (into EB1)
RV1 Drive pedal potentiometer
SW1 Driver’s seat microswitch
Color codes
BK Black
BU Blue
BN Brown
GN Green
GY Grey
OG Orange
PK Pink
RD Red
VT Violet
WH White
YE Yellow
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 11
7/11
WIRING DIAGRAM (Continues)
P100434
6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
12 FOCUS II Micro Rider - 9099236000 7/11
USE
WARNING!

–DANGER
–WARNING
–
–
While reading this Manual, the operator must pay particular attention to the symbols shown on the plates.
Do not cover these plates for any reason and immediately replace them if damaged.
BATTERY CHECK/SETTING ON A NEW MACHINE
WARNING!
The electric components of the machine can be seriously damaged if the batteries are either improperly installed


Check the batteries for damage before installation.
Disconnect the battery connector and the battery charger plug.
Handle the batteries with great care.
Install the battery terminal protection caps supplied with the machine.
The machine requires 4 6 V batteries, connected according to the diagram (38).
The machine can be supplied in one of the following modes:
Batteries (WET or GEL/AGM) already installed and ready to be used
1. Open the cover (20) and check that the recovery tank (19) is empty, otherwise empty it with the drain hose (24).
2. Close the cover (20).
3. Carefully lift the recovery tank assembly (19) from left side.
4. Check that the batteries are connected to the machine with the connector (9).
5. Carefully lower the recovery tank assembly (19).
6. Insert the ignition key (58) and turn it to “I”. If the green warning light (62) turns on, the batteries are ready to be used. If the
yellow or red warning light turns on, the batteries must be charged (see the procedure in Maintenance chapter).
Without batteries
1. Buy appropriate batteries (see Technical Data paragraph).
 
2. Set the machine according to the type of batteries installed (WET or GEL/AGM) (see the following paragraph).
3. Install the batteries (see the following paragraph).
4. Charge the batteries.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 13
7/11
BATTERY INSTALLATION AND BATTERY TYPE SETTING (WET OR GEL/AGM)
Battery installation
1. Open the recovery tank cover (20) and check that the recovery tank (19) is empty, otherwise empty it with the recovery water
drain hose (24).
2. Close the cover (20).
3. Carefully lift the recovery tank assembly (19).
4. Install the batteries and connect them according to the diagram (38).
Battery type setting
Set the function electronic board of the machine and the battery charger according to the type of batteries installed (WET or GEL/
AGM) as shown below:
5. 

SETTING DISPLAY (71) BATTERY WARNING LIGHT INDICATION (62) BATTERY TYPE
1 WET
2 GEL-AGM
6. If the setting is to be changed, perform the following procedure.
7. Turn off the machine by turning the ignition key (58) to “0”.
8. Press and hold the switches (63) and (65) at the same time, then turn the ignition key (58) to “I”.
9. Release the switches (63) and (65) within 5 seconds of starting the machine.
10. Within 3 seconds, press the switch (65) to go to the next setting (1 to 6 in sequence).
NOTE
When performing steps 9 and 10, the settings are shown on the display (71) according to the code in the above table.
NOTE
The battery charger must be set according to the type of batteries.
Battery charging
11. Charge the batteries (see the procedure in Maintenance chapter).
6/14
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
14 FOCUS II Micro Rider - 9099236000 7/11
BEFORE MACHINE START-UP
WARNING!
At every machine start-up, check that, between the deck (5, 10 and 28) and the machine or between the

lifting. This check is necessary because, if the machine has been turned off without lifting the deck and the

Pad-holder installation/removal (for FOCUS II MICRO RIDER 26D)
According to the kind of cleaning to be performed, the machine can be equipped either with brushes (A, Fig. 1) or pad-holders (B)
with pads (C).
For the installation/removal, proceed as follows.
WARNING!
Before turning on the switch (63), always check that between the deck (10) and the machine there is no foreign
material which may prevent the deck from lifting.
1. Lift the deck by pressing the switch (63).
2. Turn the ignition key (58) to “0”.
3. Manually move the deck assembly to the left, then release the lever (D) and disassemble the covers (E) and (F) from the deck.
4. Install the brushes/pad-holders on the deck drive hub (G) by pushing them upwards until they are engaged.
5. 
WARNING!
If the machine is not perfectly assembled it can cause damage to people and property. Always check that all
components are assembled before starting the machine. Carefully inspect the machine before using it.
A
G
A
E
F
D
B
C
B
C
Front
Figure 1
P100435
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 15
7/11
Available brushes and their relevant application guides (suggestions only)
Models HEAVY GRIT LITE GRIT MEDIUM GRIT POLY SOFT NYLON UNIVERSAL
BRUSH 5K
General cleaning:
Concrete

Ceramic tiles/quarrystones
Marble
Vinyl tiles
Rubber tiles
Polishing:
Rubber tiles
Marble
Vinyl tiles
Pad installation/removal (for FOCUS II MICRO RIDER 28 BOOST®)
The machine with BOOST®
1. Insert the ignition key (58) and turn it to “I”.
WARNING!
Before turning on the switch (63), always check that between the deck (28) and the machine there is no foreign
material which may prevent the deck from lifting.
2. Lift the deck by pressing the switch (63).
3. Turn the ignition key (58) to “0” and remove it.
4. Install the pad (A, Fig. 3) so that it engages the plates on the BOOST®deck.
5. To remove the pad perform steps 1 to 3, then manually release the pad from the deck plate.
A
Figure 3
P100437
Squeegee installation
6. Install the squeegee (30) and fasten it with the handwheels (34), then connect the vacuum hose (31) to the squeegee.
7. 

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
16 FOCUS II Micro Rider - 9099236000 7/11

NOTE


CAUTION!

WARNING!


1. 
2. (For machines without Chemical Mixing System)
Fill the tank (22) with a solution suitable for the work to be performed.

Always follow the dilution instructions on the label of the chemical product used to prepare the solution.
The solution temperature must not exceed 104°F (40°C).
(For machines with Chemical Mixing System)
Fill the tank (22) with clean water.

The water temperature must not exceed 104°F (40°C).
Detergent tank replacement (for machines with Chemical Mixing System)
1. Open the recovery tank cover (20) and check that the recovery tank (19) is empty, otherwise empty it with the drain hose (24).
2. Close the recovery tank cover (20).
3. Carefully lift the recovery tank assembly (19) from left side.
4. Uncap the detergent tank (42).
5. Remove the empty container and replace it with a new one.
6. Insert the hose properly and screw down the cap on the detergent tank.
NOTE

it may be useful to drain the Chemical Mixing System once or several times (see the procedure in Maintenance chapter).
Driver’s position adjustment
1. Using the lever (73), adjust the height of the steering wheel (1) to reach a comfortable position.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSTRUCTIONS FOR USE ENGLISH
9099236000 - FOCUS II Micro Rider 17
7/11
MACHINE START AND STOP
Starting the machine
1. Prepare the machine as shown in the previous sections.
2. Turn the ignition key (58) to “I” without pressing the drive pedal (4). Check if the battery green warning light (62) turns on.
 If the yellow or red warning light turns on, turn the ignition key (58) back to “0” and charge the batteries (see the procedure
in Maintenance chapter).
3. Drive the machine to the working place with both hands on the steering wheel (1) and by pressing the pedal (4).
4. Reverse speed is selected with the switch (51, LED 52 on).
5. To go back to forward speed press again the switch (51, LED 52 off).
NOTE
The driver’s seat (17) is equipped with a safety sensor which allows the machine to be moved with the pedal (4) only
when the operator is on the driver’s seat.
NOTE

when the machine tilts laterally, regardless of the pressure on the pedal.
In this case, the reduction of speed is not a malfunction but a characteristic that improves the machine stability and
safety in every condition.
6. Lower the brush/pad-holder deck and the squeegee by pressing switch (63).
7. 
8. Start scrubbing, by starting it with both hands on the steering wheel (1) and by pressing the pedal (4).
 Adjust the speed with the switches (69) according to the necessities or the work to be performed.
NOTE
The machine is equipped with a safety system that turns on the brushes and vacuum system only when the machine is
moving.
Stopping the machine
9. Release the pedal (4).
10. It is not necessary to lock the machine during stopping or parking, because the electromagnetic brake on the wheel turns on
automatically when the drive pedal is not pressed.
11. Lift the brush/pad-holder deck and the squeegee by pressing the switch (63).
MACHINE OPERATION (SCRUBBING/DRYING)
1. Start the machine as shown in the previous paragraph.
2. If necessary, adjust the solution quantity by pressing the switches (59 and 60).
3. If necessary, to reduce the noise, turn on the mute function by pressing the switch (55).
NOTE
The mute function will reduce the vacuum suction performances as well, so it is suggested to use the mute function only

NOTE


B
A
Figure 4
P100438
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ENGLISH INSTRUCTIONS FOR USE
18 FOCUS II Micro Rider - 9099236000 7/11
Squeegee adjustment
1. 
all its length.
Adjustment of the detergent concentration in the solution
(For machines with Chemical Mixing System)
The system used to mix the detergent with the washing water can be activated by pressing the detergent concetratium control
switch (A, Fig. 5): when one of the LEDs is on, the detergent is added to the washing water.
1. 
2. Press the switch (A) to change the detergent concentration to reach the desired setting, or to reset (all LEDs off).
NOTE
Detergent percentage setting is stored into memory, even if the machine is turned off.
NOTE

B
A
C
D
E
F
0,4%
0,5 Oz/Gal
0,75%
1 Oz/Gal
1,5%
2 Oz/Gal
2,5%
3 Oz/Gal
Figure 5
P100439
Working with brush/pad-holder extra pressure function turned on
1. 
pressing the switch (E, Fig. 5).
2. To return to normal pressure, press the switch (E) again.
 The switch (E) is enabled only when the deck (5 and 10) is lowered and the LED (F) of the switch is on.
CAUTION!


of continuous overload.

If the overload takes place when the extra pressure function is on, the system automatically reduces the



key (58) to “0”. Turn on the machine by turning the ignition key (58) to “I”.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080