Clarke CML6 User manual

USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS GC 08/22
MOTORCYCLE TABLE LIFT
MODEL NO: CML6
PART NO: 7610194

2
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
INTRODUCTION
Thank you for purchasing this CLARKE Motorcycle Table Lift.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
SPECIFICATION
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
Max Rated Load 500 kg
Product weight 13.7 kg
Product dimensions 494 x 312 x 163 mm
Min height of table 90 mm
Max height of table 400 mm
Max height of lifting cups from rest 470mm to bottom of cup
Min height of lifting cups from rest 160mm to bottom of cup
Table Size 450 x 150 mm

3
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
SAFETY PRECAUTIONS
1. Ensure that the lift is in good working order. Have any damaged parts
repaired or replaced immediately. Use genuine CLARKE parts only. The use
of unauthorised parts may be dangerous and will invalidate the warranty.
2. Only use the lift in a suitable, well lit work area.
3. Keep the work area clean and tidy and free from unrelated items.
4. Use the lift on level and solid ground, preferably concrete. Avoid soft/
unmade ground as the lift may sink in.
5. Ensure the engine is switched off and the transmission is in 1st or reverse
gear.
6. Ensure a minimum distance of 0.5 m between the motorcycle and static
objects such as doors, walls, etc, to allow for the motorcycle tilting.
7. Check the lifting point is rigid and centred on the lift saddles.
8. Place chocks under the wheels of the motorcycle.
9. Keep all non-essential persons at a safe distance whilst the lift is in use.
10. Ensure there are no personnel or obstructions under the motorcycle before
lowering.
11. Take care not to trap fingers in the moving parts of the lift.
12. DO NOT allow personnel to operate the lift unless they have read these
safety precautions.
13. DO NOT exceed the rated capacity of the lift.
14. DO NOT lift a motorcycle if there is a risk of spillage of fuel, battery acid or
other dangerous substances.
15. NEVER tamper with the product or modify it in any way, as this could prove
to be dangerous and will invalidate the guarantee. Only use the product
for the purpose for which it is intended.
16. When not in use, store the lift fully lowered, in a safe, dry, childproof area.
17. No responsibility can be accepted for incorrect use of the lift.
LIFTING OPERATIONS AND LIFTING EQUIPMENT REGULATIONS 1998
This lift, depending on use, may fall within the scope of LOLER. It is the owner’s
responsibility to determine whether or not it does and, if so, to comply with any
applicable requirements in LOLER, for having the lift thoroughly examined.

4
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
OPERATING INSTRUCTIONS
POSITIONING THE LIFT
NOTE: If required, the lift can be bolted to a floor or bench as a
permanent installation using the mounting bolt holes in the base.
(Mounting bolts not supplied).
The lift is raised by turning the spindle with the 21mm box wrench provided. DO
NOT attempt to use a power tool.
1. Position the motorcycle in a suitable area, checking that the surface
on which the lift will be placed is solid and flat (preferably concrete).
2. Ensure there is good access and clearance beneath the motorcycle for the
lift.
• The lift can be also be used in conjunction with a motorcycle
that is already raised on a motorcycle lift. Ensure that the lift is
fully located on the lift platform.
3. Slide the two sliding brackets
over the platform of the lift.
4. Inspect the underside of the
motorcycle for suitable
support points, bearing in
mind the centre of gravity of
the motorcycle and which
wheel is to be lifted from the
ground.
5. Screw the saddles into the
sockets of the sliding brackets.
6. Place the lift under the motorcycle in the approximate position required.
WARNING: BEFORE LIFTING, ENSURE THE SAFETY PRECAUTIONS ARE
STRICTLY FOLLOWED.
WARNING: BEFORE USE, ENSURE THAT THE MOTORCYCLE HAS A SUITABLE
STRUCTURE AND CENTRE OF GRAVITY TO ACCOMMODATE THE LIFT
SUPPORTS WITHOUT DAMAGING THE MOTORCYCLE.
CAUTION: DO NOT USE THE LIFT IF IT WILL FOUL ON THE EXHAUST OR
OTHER VULNERABLE PARTS. IF NECESSARY REMOVE ANY LOWER FAIRING
AND ENSURE THAT THE MOTORCYCLE IS STABLE ON THE SUPPORTS
BEFORE OPERATING.

5
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
LIFTING THE MOTORCYCLE
1. Use the box wrench to raise the platform until the saddles reach the
intended points of contact on the underside of the motorcycle. Adjust
the position of the lift and/or sliding brackets as necessary and proceed to
raise the motorcycle.
2. Lock the position of the sliding brackets for greater security using the bolts
on one side.
3. Turn the box wrench slowly and evenly to ensure no sudden movements of
the motorcycle.
4. For additional security it is advisable to retain the motorcycle on the
stand with suitable straps, especially if the motorcycle is already raised
from the ground on a motorcycle lift.
LOWERING THE MOTORCYCLE
1. When work is complete, check under the lift platform to ensure that there
are no obstructions and that it is safe to lower the unit.
2. Slowly turn the box wrench anti-clockwise to lower the motorcycle.
3. When the lift is fully lowered, ensure that the motorcycle is standing on its
wheels and is supported in the upright position.
CARE AND MAINTENANCE
1. Keep the lift clean and lubricate all moving parts with oil if required.
2. Before each use check for broken, cracked, bent, or loose parts, or any
visible damage to welds, saddle, frame and all parts including pins and
other fasteners. If any suspect item is found remove jack from service and
take necessary action to remedy the problem.
3. DO NOT use the lift if believed to have been subjected to abnormal load or
shock. Inspect and take appropriate action.
4. Store the lift in its lowest position in a dry location.
WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER AND
ENSURE THERE ARE NO PERSONS OR OBSTACLES BENEATH THE
MOTORCYCLE, OR IN THE PATH OF ITS DESCENT.

6
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
COMPONENT PARTS
No Description No Description
1 Table 13 Washer 20mm
2 Bolt M12 x 50 14 Outer lifting arm
3 Washer 12 15 Connecting spindle
4 Saddle 16 Centre spacer
5 Adjustable plate 17 Roller
6 Bolt M10 x 25 18 Inside lifting arm
7 Box Wrench 19 Bearing
8 Lifting screw 20 Front mounting block
9 Inside fixing spindle 21 Nut
10 Circlip 22 Locknut
11 Base plate 23 Rear mounting block
12 Outer frame roller 24 Nut M8

7
Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]
DECLARATIONS OF CONFORMITY