Clarke DK38 User manual

05_60162_B4
1
Before you start: 2 or more individuals recommended for assembly, approximate time 1.5 hrs.
Please read instructions COMPLETELY before assembly. This shelter MUST be securely anchored.
RECOMMENDED TOOLS
8' x 4' x 5'6" Pet Kennel
Assembly Manual
OR
Clarke International
Hemnall Street
Epping
Essex CM16 4LG
ENGLAND
www.clarkeinternational.com
PARTS & SERVICE: 0208 988 7400
E-mail: [email protected] or
[email protected]
SALES: UK 01992 565333 or
EXPORT: 00 44 (0)1992 565335
6/15/12
DESCRIPTION MODEL #
8' x 4' x 5'6"
A B C DK38
3503516
Peak Kennel 2.4 x 1.2 x 1.7 M - Green
C
A
B

05_60162_B4
2
PROPER ANCHORING OF THE FRAME IS THE RESPONSIBILITY OF THE CONSUMER.
Clarke®International are not responsible for damage to the unit or the contents from acts of nature. Any kennel that is not anchored
securely has the potential to cause damage. Periodically check the anchors to ensure stability of the kennel. Clarke®International
cannot be responsible for any kennel damaged as a result of improper anchoring. NOTE: Your kennel and cover can be quickly
removed and stored prior to severe weather conditions. If strong winds or severe weather is forecast in your area, we recommend
removal of kennel.
PRoPeR AncHoRinG And insTAllATion oF FRAme:
ATTenTion:
This kennel is manufactured with quality materials. It is designed to t the fabric cover included. Please anchor the kennel carefully
following the instructions in this manual. Proper anchoring, keeping cover tight and free of snow and debris is the responsibility of the
consumer. Please read and understand the installation detail, warnings and cautions prior to beginning installation.
cAUTion:
Use CAUTION when erecting the frame.
Risk of re. DO NOT smoke or use open ame devices (including grills, re pits, deep fryers, smokers or
lanterns) in or around the kennel. DO NOT store ammable liquids (gasoline, kerosene, propane, etc.) in
or around your kennel. Do not expose top or sides of the kennel to open re or other ame source.
WARninG:
Choose the location of your kennel carefully. DANGER: Keep away from electrical wires. Check for
overhead utility lines, tree branches or other structures. Check for underground pipes or wires before
you dig. DO NOT install near roof lines or other structures that could shed snow, ice or excessive run
off onto your kennel. DO NOT hang objects from the roof or support cables.
dAnGeR:
Overall kennel is easily cleaned with a garden hose or soap and water. A tight cover ensures longer life
and performance. Always maintain a tight cover. Loose fabric can accelerate deterioration of cover fabric.
Immediately remove any accumulated snow or ice from the roof structure with a broom, mop or other soft-
sided instrument. Use extreme caution when removing snow from cover- always remove from outside the
structure. DO NOT use hard-edged tools or instruments like rakes or shovels to remove snow. This could
result in punctures to the cover. DO NOT use bleach or harsh abrasive products to clean the fabric cover.
Cover is easily cleaned with mild soap and water.
cARe And cleAninG:

05_60162_B4
3
Quantity Part #
Description of Parts:
3-Way Side Connectors (R)
1/4" x 1-1/2" Bolts
1/4" Nuts
1'4" Gaskets
Plug for Tube
Clamp
Cross Rail 471
/ 4in.
Anchors
Front Panel
Cover
Top Rafter Poles 181
/ 2in.
Side Frame
Front Frame
8' x 4' x 5'6" Pet Kennel - Parts List - Model # DK38 3503516
3-Way Top Connectors
3-Way Side Connectors (L)
Foot
Ratchet
Back Panel
Cross Rail 461
/ 4in.
4-Way Side Connectors
4-Way Top Connectors
18108
18182
800248
10240
03025
800247
18166
01010
01011
15237
800215
18110
18107
18104
18111
18192
800249
18112
18109
803065
18105
6
5
4
1
1
24
2
18
18
18
6
1
11
2
2
3
1
6
3
2
1
NOTE: The anchors are available from our spare parts department.
Please quote the Part No. 18166

05_60162_B4
4
1. RooF AssemBlY
03025
01010
01011
800215
2. AssemBle Kennel
36
17
6
28
4
5
1
6
3
8
5
7
4
Fig. 1
Assemble your kennel's roof frame as shown. Fig. 1.
Assembly
Reference
Quantity
of Parts
Mfg.
Part #
1 2 18104
2 1 10105
3 2 18107
4 2 18108
5 2 18109
6 6 18110
7 3 18111
8 3 18112
Assemble the side panels so that the two holes in the
vertical tubes are on the top, and the wire mesh is
on the outside of the kennel. (Fig. 2)
Each connection should be held together with 2
clamp sets: (2) 800215 clamps, (1) 03025 bolt, (1)
01011 washer and (1) 01010 nut.
Position each clamp set where the wire mesh has
been cut (Fig. 3) and the head of the bolt should be
inside the kennel. The nut and washer should be on
the outside to ensure the safety of the animal.
The side panels of the kennel should be installed
between the front and rear panel (all of the clamps
should be in the same direction as the side wall) to
make the kennel the correct size. noTe:
It will be necessary to
open the gate to install the clamp
sets for that corner of the kennel.
Fig. 2
noTe: Holes in panels must be on top
800248
}
800247
Fig. 3
800248
800248
800248
800248
800248
800247

05_60162_B4
5
4. ATTAcH FRonT And BAcK PAnels
noTe: Wrap hook and loop
around the rafter.
noTe: The back panel is longer
than the front panel.
15237
Back Panel
Front Panel
With help, lift the roof assembly up
and over the assembled walls.
The (4) corner bends will insert into
the outer tubes on the front and rear of
the kennel. (Fig. 4)
The middle connection will go into the
middle connection that is closest to
the side bend (the cross rails are
two different lengths to accommodate
this offset). (Fig. 5)
After you have inserted all of the
uprights, go around the kennel again,
seating the roof completely (push the
roof assembly all the way down).
Lastly, insert the plastic plugs (part
#15237) into the open ends at the top
of the wall panels.
Fig. 4 Fig. 5
3. ATTAcH RooF
18182
18192
Secure the front and back panels to the roof
assembly using the "Hook and Loop" straps.
Secure the peak and then the sides to be sure the
position is correct. Secure the remaining straps
once the panel is in the correct position. (Fig. 6)
Fig. 6

05_60162_B4
6
6. ATTAcH FeeT And AncHoRs
5. ATTAcH coVeR
A. Hook Ratchet
in hole on panel
B. Pull webbing
through ratchet
and tighten
803065
18166
10240
Insert anchor rods around base of
kennel, evenly spaced.
noTe:
A: Insert the feet (800249) into the open ends of the
corner legs by lifting the kennel just high enough to t
the foot underneath. Apply force to secure the foot to
the corner legs. Repeat this for the remaining feet.
B: Insert one anchor (18166) in each hole of the bottom
rail, and press into the ground to secure. (Fig. 8)
A
A
A
A
A
AB
B
BB
B
B
B
B
BB
B
Fig. 7
Fig. 8

05_60162_B4
7
PARTS & SERVICE: 0208 988 7400
E-mail: [e-mail] or [e-mail]
SALES: UK 01992 565333 or EXPORT: 00 44 (0)1992 565335
www.clarkeinternational.com
Hemnall Street, Epping, Essex CM16 4LG
OTHER QUALITY LEISURE & GARDENING
PRODUCTS AVAILABLE FROM
LOGBUSTERS
BANQUETING TABLES
BBQ’s
PORTABLE GENERATORS
GARDEN TROLLEYS
BINOCULARS
LED HEADLIGHTS / FLASHLIGHTS
HOT & COLD POWER WASHERS
tarpaulins • insect killers
CAR COVERS
INVERTERS
JUMP STARTS
foot pumps • fans
LADDERS
AND MUCH MORE!