Clarke MDS1 User manual

1
VARIABLE SPEED
JIG SAW
ASSEMBLY INSTRUCTIONS
0308
Part No. 6460200
MILL DRILL STAND
MODEL No. MDS1
Part No. 6500330
MILL DRILL STAND

2
Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE
International reserve the right to change specifications at any time without prior notice.
Whln disposing of this product, ensure it is disposed of according to all local ordinances. It must
not be disposed of with general household waste.
PARTS LIST
Unpack the carton and lay out all components, checking to ensure that
they are complete, against the list which follows.
Check also for any damage which may have occurred in transit. Please
notify your CLARKE dealer immediately should any be found.
(1) (2) (3)
(4) (5)
(6) (7)
(8)
(9) (10)
(11)
(12)
(13)
(14) (15)

3
PARTS LIST
ON NOITPIRCSED YTQ REBMUNTRAP
1lanaptnorF11001SDMTH
2slanapediS22001SDMTH
3lanaPraeR13001SDMTH
4flehS14001SDMTH
5yarT15001SDMTH
601MtuN46001SDMT
H
7mm01,rehsaWtalF46001SDMTH
8031X01M,001X01MtloBhcaoC46001SDMTH
98MtuN616001SDMTH
01mm8,rehsaWtalF236001SDMTH
11tloB21x
8M616001SDMTH
21mm6,rehsaWtalF76001SDMTH
3121X6MwercS76001SDMTH
4161MtuN16001SDMTH
51wercsniarD16001SDMTH
Please note, Parts 6-15 are supplied as a complete set (HTMDS1006)

4
ASSEMBLY
1. Attach the side panel (2) to
the rear panel (3) as shown
and secure into place
using, 4 nuts (11), bolts (9)
and flat washers (10).
2. Place the shelf (4) into the
position shown and using
the screw (13) and washer
(12) provided screw it into
position.
Do not fully tighten the
screw at this stage.

5
ASSEMBLY
3. Connect the second side
panel (2) to the rear panel
(3) as shown and secure
into place using, 4 nuts
(11), bolts (9) and flat
washers (10).
4. Place the front panel (1)
into position and screw the
other end of the shelf (4)
to the front panel (1),
using a screw (13) and
washer (12) provided.
5. Join the front panel (1) to
the side panels using 8
nuts (11), bolts (9) and flat
washers (10) provided.

6
ASSEMBLY
( 15 )
( 8 )
( 8 )
6. Place the tray (4) on top
of the stand and line up
the holes. Fix into place
using the remaining 4
screws (13) and washers
(12).
7. Place the drain bolt (15)
into position and secure
using the 24mm nut (14).
8. The compleated unit
should look like this.
9. The coach bolts (8) have
been shown in position for
reference.

7
10. Press here to open the
door on the front panel
11. Push the catch back into
place to lock the door.
ASSEMBLY
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a
period of 12 months from the date of purchase. Please keep your
receipt as proof of purchase. This guarantee is invalid if the product is
found to have been abused or tampered with in any way, or not used
for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission. This guarantee does not
effect your statutory rights.

8