Clarke MA10 12E User manual

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •F a x : 8 0 0 . 26 3. 5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
Operating Guidelines
MA10™12E
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
2. Fill the solution tank with clean
water, not to exceed 100° F.
3. The tank cap can be used for
dosing the detergent. One full cap
is 30 ml giving 1% detergent of the
0.8 gal (3 L) tank capacity. (*)
4. Connect the power plug to an
electrical socket.
1. Release the handle to remove the
tank assembly.
19. Wipe down the machine using a
damp cloth, and where needed
use a neutral cleaning product.
Then store the machine in a clean
and dry place.
18. Clean the squeegee bars and
the cylindrical brush with water.
Check for wear and replace
when necessary.
16. Remove the cylindrical brush by
turning the side knob clockwise.
14. Empty the recovery and solution
tank. Clean them with water.
13. Disconnect the power plug from
the electrical socket and rewind
the cord, starting at the machine,
and place it in the cord holder.
10. When necessary, empty the
recovery tank and rell the
solution tank to continue working.
11. To use the manual suction hose,
press the power switch to start the
machine in upright position. Turn the
hose connection to ON and use the
suction tube. When done, turn hose
connection to OFF. (**)
12. Park the machine in the upright
position and turn off the power
switch.
15. Check and clean the solution and
vacuum lter regularly.
17. Remove the squeegee bars.
7. Press the start/stop switch to start
the machine.
5. Press the black pedal to put the
machine in working position.
6. For double scrubbing, ip the
pedal to lift/lower squeegees.
8. Press the solution switch to start
the solution ow.
9. Move the machine with the handle
and start cleaning the oor.
When nished using
(*) ALWAYS FOLLOW THE DETERGENT DOSING RECOMMENDATION ON THE LABEL OF THE CHEMICAL PRODUCT USED.
(**) THE MANUAL SUCTION HOSE IS AN OPTIONAL ACCESSORY.

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •F a x : 8 0 0 . 26 3. 5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0. 26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E

9435 Winnetka Avenue North •Brooklyn Park, MN 55445
Phone: [phone] •Fax: [phone]
240 Superior Boulevard •Mississauga, Ontario, Canada L5T 2L2
Phone: [phone] •Fa x: 8 0 0.26 3.5111
The machine
doesn’t work
as it should?
The suction
doesn’t work
as it should?
The machine
doesn’t clean
as it should?
The brush
doesn’t work
as it should?
1. Check if the power supply cord is
damaged, faulty or disconnected
from the electrical mains.
2. Check if the recovery tank is full.
1. Check if you have pressed the
solution switch or the solution tank
is empty.
2. The switches are broken. (*)
3. Check if the squeegee bars are
dirty or the blades are worn or
damaged.
2. Check if the solution lter is dirty.
Clean it if needed.
1. Check if the cylindrical brush is
correctly installed and not worn out.
Replace when necessary.
(*) For these causes the maintenance
procedure must be performed by an
authorized Clarke Service Center.
For further information refer to the
Service Manual.
4. Check if the inspection compartment
is dirty. Check if the recovery vacuum
hose is disconnected or dirty.
3. Check if the holes in solution
dispensers are clogged. Remove
them and clean if needed.
1. If applicable, check if the manual
suction hose connection is turned
to “OFF”.
ATTENTION! Do not use the machine before you have read and understood the Instructions for Use Manual.
Troubleshooting
MA10™12E