Clarke Woodworker CDE1000 Installation and operation manual

OPERATING & MAINTENANCE
INSTRUCTIONS
MODEL No: CDE1000
Part No:6471165
GC0514
DUST EXTRACTOR

2
INTRODUCTION
Thank you for purchasing this CLARKE Dust Extractor which is intended to keep
work areas free from dust particles & wood shavings etc.
Please read this manual thoroughly and follow the instructions carefully. Before
attempting to use the product, thoroughly familiarise yourself with the product
& its operation. In doing so you will ensure the safety of yourself and that of
others around you, and you can look forward to the product giving you long
and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tam-
pered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL RECYCLING POLICY
Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE regula-
tions in relation to the treatment, recycling & recovery and environ-
mentally sound disposal of the WEEE.
In effect, this means that this product must not be disposed of with
general household waste. It must be disposed of according to the laws
governing Waste Electrical and Electronic Equipment (WEEE) at a recognised
disposal facility.
SPARE PARTS & SERVICING CONTACTS
For parts & Servicing, please contact your nearest dealer, or CLARKE International, on
one of the following numbers.
PARTS & SERVICE TEL: [phone]
PARTS & SERVICE FAX: [phone]

3
TABLE OF CONTENTS
INTRODUCTION ...................................................................................2
GUARANTEE ........................................................................................2
ENVIRONMENTAL RECYCLING POLICY .............................................2
SPARE PARTS & SERVICING CONTACTS .............................................2
TECHNICAL SPECIFICATION ............................................................... 3
SAFETY PRECAUTIONS ........................................................................4
ELECTRICAL CONNECTIONS ..............................................................6
UNPACKING & ASSEMBLY ..................................................................7
OPERATION & MAINTENANCE ...........................................................9
TROUBLESHOOTING ............................................................................9
PARTS LIST & DIAGRAM......................................................................10
DECLARATION OF CONFORMITY .......................................................11
TECHNICAL SPECIFICATION
Please note that the details and specifications contained herein, are correct at the
time of going to print. However, CLARKE International reserve the right to change
specifications at any time without prior notice.
Specification
Weight 10 kg
Dimensions (d x h) 390 x 665 mm
Inlet Hose Diameter / Length 100 x 2000 mm
Air Flow 183 m3/h
Suction 25000 Pa
Container Volume 50 L
Input Voltage 230v / 50 Hz
Motor Speed 20000 rpm
Input Wattage 1100 W
Fuse Rating 13 A
A weighted sound pressure level (Lpa) 80 dB

4
SAFETY PRECAUTIONS
WORK AREA
1. ALWAYS keep the work area clean and well lit. Floors should always be
kept clear. Cluttered or dark areas invite accidents.
2. ALWAYS keep children away and keep visitors at a safe distance from the
work area, especially whilst operating the machine.
PERSONAL SAFETY
1. ALWAYS stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a machine while you are tired or
under the influence of medication, drugs or alcohol.
2. NEVER over-reach. Keep your proper footing and balance at all times to
enable better control of the machine in unexpected situations.
3. ALWAYS wear safety goggles, manufactured to the latest European Safety
Standards. Everyday eyeglasses do not have impact resistant lenses and
are not safety glasses.
4. ALWAYS concentrate on the job in hand, no matter how trivial it may
seem. Accidents are caused by carelessness due to familiarity.
5. ALWAYS keep your proper footing and balance at all times. For best
footing, wear rubber soled shoes. Keep floor clear of oil, scrap wood, etc.
GENERAL USE AND CARE
1. ALWAYS ensure that the appliance cannot be started inadvertently by
using the ON/OFF switch whenever carrying out maintenance.
2. ALWAYS maintain in top condition. Keep appliances clean for the best and
safest performance. Follow maintenance instructions.
3. NEVER modify this product in any way. Use it only for the purpose for which
it is designed.
4. ALWAYS check for damage. Check for any condition that may affect the
machine’s operation. Any damage should be properly repaired or the
part replaced. If in doubt, DO NOT use the machine. Consult your Clarke
dealer.
5. ALWAYS keep the mains cable well away from any machinery and ensure
an adequate electrical supply is close to hand so that the operation is not
restricted by the length of cable.
6. NEVER drag the machine by its power cable, or pull the cable to
disconnect it from the power supply.
7. ALWAYS ensure the switch is off before plugging into mains. Avoid
accidental starting.

5
8. NEVER use if the ON/OFF switch does not turn it on and off. A machine
that cannot be controlled with the switch is dangerous and must be
repaired.
9. ALWAYS store out of reach of children and do not allow persons unfamiliar
with these instructions to operate this machine.
DUST EXTRACTOR SAFETY INSTRUCTIONS
1. ALWAYS ensure that the dust extractor is properly positioned where
necessary to prevent it from moving during use and that the immediate
area is kept clear.
2. ALWAYS use a face or dust mask if operation is particularly dusty such as
when disposing of the contents of the collecting bag.
3. ALWAYS disconnect the dust extractor from the power supply before
servicing or removing & emptying the collecting bag etc.
4. NEVER leave the dust extractor running unattended. Turn power off and
wait for the machine to come to a complete stop before leaving.
5. DO NOT pick up flammable or readily combustible material, hot ashes,
coals, burning cigarettes or other smoking substances etc. or use in the
presence of explosive liquids or vapour.
6. DO NOT use in enclosed areas where flammable, explosive or toxic
vapours are given off, by oil based paints, paint thinner, petrol etc.
7. DO NOT use if the electric cable, plug, collection bag or the motor is in
poor condition.
8. ALWAYS use in an upright position.
SERVICING
1. If necessary, have your machine repaired by a qualified person using
identical replacement parts. This will ensure that the safety of the machine
is maintained.
Please keep these instructions in a safe place for future reference.

6
ELECTRICAL CONNECTIONS
This product is provided with a 13 amp BS 1363 plug, fitted with a 13amp fuse and
MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably
through an approved plug, or a suitably fused isolator switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in the mains lead should be wired up in accordance
with the following colour code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible cable of this appliance may not correspond with
the coloured markings identifying terminals in your plug, proceed as follows:
• Connect the GREEN & YELLOW coloured cord to the plug
terminal marked with a letter E or Earth symbol “ ” or
coloured GREEN or GREEN & YELLOW.
• Connect the BROWN coloured cord to the plug terminal
marked a letter “L” or coloured RED.
• Connect the BLUE coloured cord to the plug terminal marked
a letter “N” or coloured BLACK
If this appliance is found to be fitted with a plug which is moulded on to the
electric cable (i.e. non-rewireable) please note:
1. The plug must be thrown away if it is cut from the electric cable. There is a
danger of electric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the
correct replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local Clarke dealer
or most electrical stockists.
FUSE RATING
The fuse in the plug must be replaced with one of the same rating and this
replacement must be ASTA approved to BS1362.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD).

7
UNPACKING
When unpacking please check contents and advise your dealer immediately
if any parts are missing. The essential parts of the machine are as follows;
1. Motor casing
2. Shavings container
3. On/off switch
4. Locking strap
Release the locking strap and
remove the motor casing.
The following are supplied loose
and require assembly;
5. Inlet hose (100 mm dia)
6. Hose clamps (x2)
7 Filter cartridge
8 Filter bags
9 Inlet adaptor set (28, 35, 40,
63 & 99mm diameter sizes)
Instruction manual (this
document)

8
ASSEMBLY
1. Place filter cartridge (1) into filter bag
(2).
2. Fold any overhang into the filter
cartridge.
3. Push the filter cartridge (1)
complete with bag (2), onto the fan
housing part of the motor casing
(3).
4. Sit the entire motor casing on the
container and secure with the
locking strap as shown in Fig 1.
5. Attach the inlet hose to the machine
body using one hose clamp as shown
in Fig 6.

9
6. Secure the other end of the inlet
hose to the hose coupling using the
other hose clamp as shown in Fig 7.
• The inlet adaptors can then be
connected as required to suit the size
of the extract duct on the wood-
working appliance to be used.
OPERATION & MAINTENANCE
Start the machine using the ON/OFF switch (I=on/O=off). Connect the inlet
hose to the outlet on your woodworking appliance using the inlet adaptors.
Take care never to suck in foreign objects such as screws, nails, large pieces
of plastic or wood.
Regularly inspect the filter for damage before use and replace if necessary.
Regularly check the tightness of the filter, filter bag and locking ring.
Check the power cable to ensure it is sound and free from cracks, bare wires
etc. Avoid using solvents when cleaning plastic parts.
TROUBLESHOOTING
melborP esuacelbaborP ydemerdetsegguS
.nurtonlliwrotoMrohctiws,elbacevitcefeD
.rotom
lacirtcelekcehC
llaotsnoitcennoc
fI.stnenopm
oc
ruoytlusnoc,lufsseccusnu
.relaedekralC
.riaehtnitsudevissecxEropartsgnikcolesooL
gnitcelloC.esohtsuahxe
.degamadgab
.snoitcennocnethgiT
.gabecalpeR
morfesiondetcepxenU
.rotom/naf
.gnibburstnenopmocesooL
edisnipu
-dliubtsuD
.gnisuoh
.relaedekralCruoytlusnoC
sliaftubsnurenihcaM
.deepsllufhcaerot
.egatlovwoL
.nrowrodegam
adrotoM
Ha ybderiapertinuev
.relaedekralCruoy
polevedotsliafrotoM
.rewoplluf
.dedaolrevotiucricylppuS
roezisre
dnudaelnoisnetxE
.gnoloot
.tiucrictnereffidesU
.daelnoisnetxeecalpeR

10
PARTS LIST & DIAGRAM
ON EDOC NOITPIRCSED ytQ ON EDOC NOITPIRCSED ytQ
1100001ECDSWreniatnoC151510001ECDSWgulp/elbacrewoP1
2200001ECDSWpartsgnikcoL161610001ECDSWhctiwsFFO/NO1
3300001ECDS
WretlifegdirtraC171710001ECDSWdnalgelbaC1
4400001ECDSWrotoM181810001ECDSWrehsawgnirpsmm51
5500001ECDSW51x5.5wercS19191000
1ECDSWrehsawaidmm51
6600001ECDSWdilreniatnoC102020001ECDSWnoihsucrebbuR2
7700001ECDSW51x5.5wercS112120001ECDSWgabretli
F1
8800001ECDSWegnopsgnoL122220001ECDSW1gnilpuocesoH1
9900001ECDSWegnopsdnuoR132320001ECDSWspmalcesoH2
01010001ECDSWgnisa
crotomH/R142420001ECDSW2gnilpuocesoH1
11110001ECDSW54x5MwercS152520001ECDSWesohtelnI1
21210001ECDSW52x5MwercS362620001EC
DSW21x5MwercS4
31310001ECDSW)kcalb(tun5M372720001ECDSW)etihw(tun5M4
41410001ECDSWgnisacrotomH/L1